Rietveld analyses and piezoelectric properties of niobium doped bismuth titanate systems

Bi 4Ti 3- xNbxO 12 (BITNb) samples, with × ranging from 0 to 0.40 were obtained using a polymeric precursor solution. Rietveld analyses confirmed that the powders crystallize in an orthorhombic structure free of secondary phases with space group Fmmm. Raman analysis evidenced a sharp increase in the bands intensity located at 129 cm -1 and 190 cm -1 due the lattice distortion in BIT02Nb and BIT04Nb compositions. UV-vis spectra indicated that addition of niobium causes a reduction of defects in the BIT lattice due the suppression of oxygen vacancies located at BO-6 octahedral. Size and morphology of particles as well as electrical behavior of BIT ceramics were affected by addition of donor dopant. Polarization reversal was investigated by applying dc voltage through a conductive tip during the area scanning and was investigated by piezoresponse force microscopy (PFM). PFM measurements revealed a decrease in piezoelectric response with increasing Nb concentration originating from a reduced polarizability along the a-axis. High spontaneous polarization is noted for the less doped sample due the reduction of strain energy and pin charged defects after niobium addition. Copyright © 2010 American Scientific Publishers.

Mango flower induction in the brazilian northeast Semi-arid with gibberellin synthesis inhibitors

Mangoes in the Brazilian semi-arid stands out in the national scenario due to high yields and fruit quality, and also to the possibility of all-year production taking advantage of the climatic conditions as well as management technique (irrigation, pruning and growth regulators application) for plant growth and blossom control. Paclobutrazol soil drench applied is normally used for production management of mangoes. This research deals with the evaluation of the effect of foliar applied growth regulators to mango, cultivar 'Kent', as regard to their efficiency for blossom management, in order to allow off season mango production. Three growth regulators (prohexadione-Ca, trinexapac-ethyl and chlormequat chloride) were foliar applied, at two dosages and compared to paclobutrazol applied as soil-drench. In order to compare the effects of the treatment, data were recorded related to panicle emission (percentage and length), period of time until blossom and production, yield (number and plant weight) and post-harvest quality of the fruit (total soluble solids, titratable acidity, pH, firmness, flesh and skin color and appearance). The results showed that prohexadione-Ca and chlormequat chloride induced a 15-day early harvest, while paclobutrazol, alone or combined with prohexadione-Ca, allow to harvest 25 days in advance, when compared to trinexapac-ethyl and control trees. Growth regulators foliar applied and paclobutrazol applied as soil-drench delayed mangoes fruit ripening in post-harvest.

Uniconazole on mango floral induction cultivar 'Kent' at submedio são francisco region, Brazil

In order to provide efficient crop management which enables the scaling of the production of mango in semi-arid conditions and achieve a greater precision in the recommendation, evaluating the effect and the influence of uniconazole foliar spray, on the emission of vegetative flushes in the cultivar 'Kent', field tests were carried out in a productive orchard. Treatments tested were three uniconazole dosages, 500, 1,000 and 1,500 mg L-1, with one, two or three respective foliar sprayings. Another treatment with paclobutrazol was used at 2.0 g a.i./m of canopy diameter, with a single application via soil and a control (without spraying of plant growth regulators), where spreader-sticker was added and the pH was adjusted. With 30, 60 and 90 days after the first spraying of the flowering inducer the growth of branches were evaluated, as well as the percentage of flowering in all treatments after 120 days of first spraying. The sprayings started in the orchard after the emission of the second vegetative flush after pruning of production, through airassisted sprayer with flow rate of 1,000 L ha-1. The experimental design was done through randomized blocks with four replications, using three plants per plot. It was observed that paclobutrazol was significantly highlighted in relation to other treatments and that the uniconazole with one, two and three foliar sprayings presented inhibition of the vegetative growth in mango 'Kent' and showed, even at low proportions, signs of flowering.

Flexibility and torsional resistance of three nickel-titanium retreatment instrument systems

Aim To assess the dimensional characteristics, flexibility and torsional behaviour of nickel-titanium retreatment instruments. Methodology Using image analysis software and high-resolution digital images, the instrument length, tip angle, diameter at 3mm from the tip and the distance between the blades (pitch length) of the following eight instruments were measured (n=12 for each measurement parameter): the ProTaper Universal retreatment (PTU-R) D1, D2 and D3 instruments; the R-Endo R1, R2 and R3 retreatment instruments; and the Mtwo retreatment (Mtwo-R) sizes 25 and 15 retreatment instruments. Maximum torque and the angular deflection at fracture as well as the bending moment at 45° were measured (n=12) according to the International Standards Organisation (ISO) specification number 3630-1. Data were analysed using the analysis of variance (α=0.05). Results The length of the active part of the instruments was found to vary according to the depth of the canal into which they were designed to reach. The pitch length also increased along the active length. The PTU-R D1 and the Mtwo-R instruments had active tips. Measurements of the bending moment at 45° revealed that the Mtwo-R 15 instrument was the most flexible, whereas the PTU-R D1 was the least flexible. The maximum torque tended to increase as the instrument diameter at 3mm from the tip increased, whereas the angular deflection at fracture varied in the opposite direction. Conclusions The geometrical characteristics of the retreatment instruments and their flexibility and torsion behaviour were consistent with their intended clinical application. © 2011 International Endodontic Journal.

Is it possible to make pixel-based radar image classification user-friendly?

In this paper we would like to shed light the problem of efficiency and effectiveness of image classification in large datasets. As the amount of data to be processed and further classified has increased in the last years, there is a need for faster and more precise pattern recognition algorithms in order to perform online and offline training and classification procedures. We deal here with the problem of moist area classification in radar image in a fast manner. Experimental results using Optimum-Path Forest and its training set pruning algorithm also provided and discussed. © 2011 IEEE.

Extração de vias combinando métodos de detecção de regiões e linhas em imagens de intensidade de pulso laser

This paper aims at extracting street centerlines from previously isolated street regions by using the image of laser scanning intensity. In this image, streets are easily identified, since they manifest as dark, elongate ribbons contrasting with background objects. The intensity image is segmented by using the region growing technique, which generates regions representing the streets. From these regions, the street centerlines are extracted in two manners. The first one is through the Steger lines detection method combined with a line length thresholding by which lines being shorter than a minimum length are removed. The other manner is by combining the skeletonization method of regions based on the Medial Axis Transform and with a pruning process to eliminate as much as possible the ramifications. Experiments showed that the Steger-based method provided results better than the method based on skeletonization.

Influence of cutting instruments and adhesive systems on hybrid layer formation.

Influence of cutting instruments and The aim of this study was to analyze the hybrid layer in noncarious dentin prepared by different cutting instruments and restored with composite resin. The cavities were randomly prepared in 40 specimens using a high-speed diamond bur (KG Sorensen 1013) and an ultrasonic tip (CVDentus C22). The cavities were restored with composite resin by varying the adhesive system between the Adper™ Single Bond (2 x 1 system, primer+adhesive) and the Prompt L-Pop™ (3 x 1 system, self-etching). The restorations were hemisected longitudinally and analyzed in the SEM (Scanning electron microscopy) in order to evaluate the hybrid layer and resinous tags characteristics, using scores ranging from 1 to 6. The Pearson test revealed a high correlation coefficient and good significance levels for both intra- and inter-raters values (r=0.90). The data were statistically analyzed using the Mann-Whitney test (P≤0.05). A larger proportion of regular hybrid layers with numerous tags were observed in the dentin prepared using the high-speed diamond burs and restored with a 2 × 1 adhesive system. Alternatively, the 3 × 1 adhesive system promoted the generation of a thin hybrid layer with few tags. After preparation using an ultrasonic tip revealed few or no tags after the preparation and 2 × 1 or 3 × 1 adhesive system application. The high-speed diamond burs produced a dentin surface that was more favorable to restorative material adhesion than the ultrasonic tips, regardless of the adhesive system used.

Efeitos de diferentes tipos de poda nos teores de nutrients emflores e frutos de goiabeira

A better understanding of the differences between the levels of nutrients, depending on the type of pruning used in the cultivation of the guava tree, may allow a more adequate understanding of the physiological processes of this fruit. The analysis of flowers is a tool that can be used to assist in assessing the nutritional status of crops, especially perennials. We evaluated the effects of different types of pruning on nutrient concentrations in flowers and fruit, at different developmental stages and in different parts of the fruit. The study was carried out in Vista Alegre do Alto, in orchards of guava variety Paluma. Flowers and fruit were collected in orchards, one under heavy pruning and the other with continuous pruning. The fruit were collected in two stages (two millimeters length and mature) and divided into basal part and apex, with the top toward the stalk. Flowers were collected in the same orchards as the fruits, sampling the basal part and apex of the flowers. F tests were performed and, when necessary, the Scott-Knott test at α= 5%. Overall, there were nutritional differences among flowers and fruits in relation to the type of pruning employed; drastic pruning provided higher levels of nutrients compared with continuous pruning. In relation to the portion of the samples, especially for fruit, there were differences between the apex and base, as well as between different stages of fruit collection.

Forced oscillations with continuum models of atomic force microscopy

The dynamics of the AFM-atomic force microscope follows a model based in a Timoshenko cantilever beam with a tip attached at the free end and acting with the surface of a sample. General boundary conditions arise when the tip is either in contact or non-contact with the surface. The governing equations are given in matrix conservative form subject to localized loads. The eigenanalysis is done with a fundamental matrix response of a damped second-order matrix differential equation. Forced responses are found by using a Galerkin approximation of the matrix impulse response. Simulations results with harmonic and pulse forcing show the filtering character and the effects of the tip-sample interaction at the end of the beam. © 2012 American Institute of Physics.

Biosolid soil application: Toxicity tests under laboratory conditions

A large volume of generated sewage sludge makes its disposal a problem. The usage of sludge in agriculture is highlighted by a number of advantages. However, heavy metals and other toxic compounds may exercise harmful effects to soil organisms. This study evaluated the possible toxic effects of a biosolid sample, under laboratory conditions, for 30 days, using diplopods Rhinocricus padbergi and plants Allium cepa (onion) as test organisms. The data obtained demonstrated that the biosolid raw sample had genotoxic potential for Allium cepa root tip cells. In the diplopods exposed to biosolid sample, epithelium disorganization in the midgut and a reduction of the volume of the hepatic cells were observed after 7 days of exposure. After 30 days, the animals still showed a reduction of the volume of the hepatic cells, but in minor intensity. Allium cepa analysis showed genotoxicity, but this effect was reduced after 30 days of bioprocessing by diplopods. This study was important to know the effects as well as to determine how this waste could be applied concerning the soil living organisms and plants. © 2012 Cintya Ap. Christofoletti et al.

Ultrasonic activation of internal bleaching agents

Aim: To evaluate the effectiveness of ultrasonic activation of bleaching agents during ex vivo internal bleaching. Methodology: Fifty canine human teeth were artificially stained, root filled and divided into five groups (n = 10) that received SP - sodium perborate plus deionized water (control group), CP - 37% carbamide peroxide gel, CPUS - 37% carbamide peroxide gel plus ultrasonic application, HP - 35% hydrogen peroxide gel or HPUS - 35% hydrogen peroxide gel plus ultrasonic application. In groups CP and HP, the bleaching agent was left inside the pulp chamber for three applications of 10 min. In groups CPUS and HPUS, the same process was performed, but ultrasonic vibration was applied to the bleaching agent by an alloy tip for 30 s, with 30 s intervals. Two sessions were performed. The colour was measured initially and after each session by an intraoral dental spectrophotometer. The variation (Δ) of the colour parameters based on the CIELab system L*, a* and b*, and the colour alteration ΔE* were calculated after first and second section. Data were analysed by one-way anova and Tukey's test. Results: There was no significant difference amongst groups for ΔL*, Δa* and ΔE*, but there was a significant difference for Δb* in the first and second sessions (P = 0.0006 and 0.0016, respectively). After the first session, Δb* was significantly greater for groups HP and HPUS, without a significant difference between them. For the second session, group HPUS had the greatest Δb* values, but they were similar to groups HP and SP; group CP had the lowest values, which were similar to groups CPUS and SP. Conclusion: Ultrasonic activation of bleaching agents during ex vivo internal bleaching was no more effective than conventional internal bleaching procedures, without activation. © 2012 International Endodontic Journal.

Influence of CVD diamond tips and Er:YAG laser irradiation on bonding of different adhesive systems to dentin

Aim: The aim of this study was to compare the microtensile bond strength of three adhesive systems, using different methods of dentin preparation. Materials and methods: A hundred and eight bovine teeth were used. The dentin from buccal face was exposed and prepared with three different methods, divided in 3 groups: Group 1 (DT)- diamond tip on a high-speed handpiece; Group 2 (CVD)-CVD tip on a ultrasonic handpiece; Group 3 (LA)-Er: YAG laser. The teeth were divided into 3 subgroups, according adhesive systems used: Subgroup 1-Adper Single Bond Plus/3M ESPE (SB) total-etch adhesive; Subgroup 2-Adper Scotchbond SE/3M ESPE (AS) selfetching adhesive; Subgroup 3-Clearfil SE Bond/Kuraray (CS) selfetching adhesive. Blocks of composite (Filtek Z250-3M ESPE) 4 mm high were built up and specimens were stored in deionized water for 24 hours at 37°C. Serial mesiodistal and buccolingual cuts were made and stick-like specimens were obtained, with transversal section of 1.0 mm2. The samples were submitted to microtensile test at 1 mm/min and load of 10 kg in a universal testing machine. Data (MPa) were subjected to ANOVA and Tukey's tests (p < 0.05). Results and conclusion: Surface treatment with Diamond or CVD tips associated with Clearfil SE Bond adhesive produced significantly lower bond strength values compared to other groups. Surface treatment with Er: YAG laser associated with Single Bond Plus or Clearfil SE Bond adhesives and surface treatment with CVD tip associated with Adper Scotchbond SE adhesive produced significantly lower bond strength values compared to surface treatment with diamond or CVD tips associated with Single Bond Plus or Adper Scotchbond SE adhesives. Clinical significance: Interactions between laser and the CVD tip technologies and the different adhesive systems can produce a satisfactory bonding strength result, so that these associations may be beneficial and enhance the clinical outcomes.

A New Miniature Characid (Ostariophysi: Characiformes: Characidae), with Phylogenetic Position Inferred from Morphological and Molecular Data

Erythrocharax altipinnis is described from the Serra do Cachimbo, Pará, Brazil. The new taxon is distinguished from all of the Characidae genera by having the pelvic bones firmly attached through the isquiatic processes; a nearly triangular hiatus in the musculature covering the anterior chamber of the swim bladder between the first and second pleural ribs (pseudotympanum); the pedunculate, notably expanded and distally compressed teeth in both jaws; circumorbital series represented by antorbital and four infraorbital bones with laterosensory canals not enclosed; a single tooth row in the premaxillary with the teeth perfectly aligned and similar in shape and cusp number; the first three branched dorsal-fin rays distinctly elongate in males; a bright red adipose and caudal fins in life; a conspicuous dark midlateral stripe extending from the opercle to the tip of the median caudal-fin rays; and by the absence of a humeral spot. The phylogenetic position of the new taxon is discussed using morphological and molecular datasets, with conflicting results of both approaches discussed. Additionally, a summarized discussion on the current problems in the Characidae taxonomy is presented and the principal biases in the morphological dataset are also discussed. © 2013 Netto-Ferreira et al.

Morphological diversity of setae on the second maxilliped of fiddler crabs (Decapoda: Ocypodidae) from the southwestern Atlantic coast

Fiddler crabs are deposit feeders, and use the setae on their mouth appendages to manipulate sediment particles to extract food. The number of spoon-tipped setae on the second maxilliped is frequently related to the distribution of fiddler crabs on estuarine sediments, but no study has compared the morphological diversity of these setae among multiple fiddler crab species. Here, we describe and classify the setae of the second maxillipeds of the nine Uca spp. known from the Brazilian coast. The second maxilliped of each species was examined by scanning electron microscopy. Six types of setae (five papposerrate, and one pappose) were described on the meropodite of the second maxilliped. Among the papposerrate setae, one type had a spoon-like tip, and the morphology of this type, especially the degree of curvature, differed between species. Members of Uca leptodactylus, U. uruguayensis, and U. maracoani had highly concave spoon-tipped setae. In U. rapax and U. cumulanta, the setal tip was moderately curved, while in U. thayeri, U. burgersi, and U. mordax, this curvature was slight. At the other extreme, the meropodite of the second maxilliped of U. vocator lacked setae altogether. This is the first study that describes differences in the degree of curvature of spoon-tipped setae in fiddler crabs. This trait may be strongly related to the distribution of these fiddler crabs on different estuarine substrates. © 2012, The American Microscopical Society, Inc.

Hisonotus bocaiuva, a new species from the rio São Francisco basin, Brazil (Teleostei: Loricariidae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)