Health monitoring of web plastifying dampers subjected to cyclic loading through vibration tests

This article investigates experimentally the application of health monitoring techniques to assess the damage on a particular kind of hysteretic (metallic) damper called web plastifying dampers, which are subjected to cyclic loading. In general terms, hysteretic dampers are increasingly used as passive control systems in advanced earthquake-resistant structures. Nonparametric statistical processing of the signals obtained from simple vibration tests of the web plastifying damper is used here to propose an area index damage. This area index damage is compared with an alternative energy-based index of damage proposed in past research that is based on the decomposition of the load?displacement curve experienced by the damper. Index of damage has been proven to accurately predict the level of damage and the proximity to failure of web plastifying damper, but obtaining the load?displacement curve for its direct calculation requires the use of costly instrumentation. For this reason, the aim of this study is to estimate index of damage indirectly from simple vibration tests, calling for much simpler and cheaper instrumentation, through an auxiliary index called area index damage. Web plastifying damper is a particular type of hysteretic damper that uses the out-of-plane plastic deformation of the web of I-section steel segments as a source of energy dissipation. Four I-section steel segments with similar geometry were subjected to the same pattern of cyclic loading, and the damage was evaluated with the index of damage and area index damage indexes at several stages of the loading process. A good correlation was found between area index damage and index of damage. Based on this correlation, simple formulae are proposed to estimate index of damage from the area index damage.

Assessment of expected damage on buildings subjected to Lorca earthquake through an energy-based seismic index method and nonlinear dynamic response analyses

The city of Lorca (Spain) was hit on May 11th, 2011, by two consecutive earth-quakes of magnitudes 4.6 and 5.2 Mw, causing casualties and important damage in buildings. Many of the damaged structures were reinforced concrete frames with wide beams. This study quantifies the expected level of damage on this structural type in the case of the Lorca earth-quake by means of a seismic index Iv that compares the energy input by the earthquake with the energy absorption/dissipation capacity of the structure. The prototype frames investigated represent structures designed in two time periods (1994–2002 and 2003–2008), in which the applicable codes were different. The influence of the masonry infill walls and the proneness of the frames to concentrate damage in a given story were further investigated through nonlinear dynamic response analyses. It is found that (1) the seismic index method predicts levels of damage that range from moderate/severe to complete collapse; this prediction is consistent with the observed damage; (2) the presence of masonry infill walls makes the structure very prone to damage concentration and reduces the overall seismic capacity of the building; and (3) a proper hierarchy of strength between beams and columns that guarantees the formation of a strong column-weak beam mechanism (as prescribed by seismic codes), as well as the adoption of counter-measures to avoid the negative interaction between non-structural infill walls and the main frame, would have reduced the level of damage from Iv=1 (collapse) to about Iv=0.5 (moderate/severe damage)

Seismic performance and damage evaluation of a reinforced concrete frame with hysteretic dampers through shake-table tests

Passive energy dissipation devices are increasingly implemented in frame structures to improve their performance under seismic loading. Most guidelines for designing this type of system retain the requirements applicable to frames without dampers, and this hinders taking full advantage of the benefits of implementing dampers. Further, assessing the extent of damage suffered by the frame and by the dampers for different levels of seismic hazard is of paramount importance in the framework of performance-based design. This paper presents an experimental investigation whose objectives are to provide empirical data on the response of reinforced concrete (RC) frames equipped with hysteretic dampers (dynamic response and damage) and to evaluate the need for the frame to form a strong column-weak beam mechanism and dissipate large amounts of plastic strain energy. To this end, shake-table tests were conducted on a 2/5-scale RC frame with hysteretic dampers. The frame was designed only for gravitational loads. The dampers provided lateral strength and stiffness, respectively, three and 12 times greater than those of the frame. The test structure was subjected to a sequence of seismic simulations that represented different levels of seismic hazard. The RC frame showed a performance level of "immediate occupancy", with maximum rotation demands below 20% of the ultimate capacity. The dampers dissipated most of the energy input by the earthquake. It is shown that combining hysteretic dampers with flexible reinforced concrete frames leads to structures with improved seismic performance and that requirements of conventional RC frames (without dampers) can be relieved.

Identification of Degraded Land in the Canary Islands; Tests and Reviews

Degraded Land is an area that either by natural causes (fires, floods, storms or volcanic eruptions) or more by direct or indirect causes of human action, has been altered or modified from its natural state. Restoration is an activity that initiates or accelerates the recovery of an ecosystem. It can be defined as the set of actions taken in order to reverse or reduce the damage caused in the territory. In the case of the Canary Islands there is a high possibility for the territory to suffer processes that degrade the environment, given that the islands are very fragile ecosystems. Added to this they are territories isolated from the continent, which complicates the process of restoring them. In this paper, the different types of common degraded areas in the Canary Islands are identified, as well as the proposed solutions for remediation, such as afforestation of agricultural land or landfill closure and restoration.

Identification and correction of besouro's faults: impact on test‐driven development experiments

Context. This thesis is framed in experimental software engineering. More concretely, it addresses the problems arisen when assessing process conformance in test-driven development experiments conducted by UPM's Experimental Software Engineering group. Process conformance was studied using the Eclipse's plug-in tool Besouro. It has been observed that Besouro does not work correctly in some circumstances. It creates doubts about the correction of the existing experimental data which render it useless. Aim. The main objective of this work is the identification and correction of Besouro's faults. A secondary goal is fixing the datasets already obtained in past experiments to the maximum possible extent. This way, existing experimental results could be used with confidence. Method. (1) Testing Besouro using different sequences of events (creation methods, assertions etc..) to identify the underlying faults. (2) Fix the code and (3) fix the datasets using code specially created for this purpose. Results. (1) We confirmed the existence of several fault in Besouro's code that affected to Test-First and Test-Last episode identification. These faults caused the incorrect identification of 20% of episodes. (2) We were able to fix Besouro's code. (3) The correction of existing datasets was possible, subjected to some restrictions (such us the impossibility of tracing code size increase to programming time. Conclusion. The results of past experiments dependent upon Besouro's data could no be trustable. We have the suspicion that more faults remain in Besouro's code, whose identification requires further analysis.

Application of PZT and FBG impedance sensors for structural health monitoring of reinforced concrete beams strengthened with FRP composite materials

Esta Tesis tiene como objetivo principal el desarrollo de métodos de identificación del daño que sean robustos y fiables, enfocados a sistemas estructurales experimentales, fundamentalmente a las estructuras de hormigón armado reforzadas externamente con bandas fibras de polímeros reforzados (FRP). El modo de fallo de este tipo de sistema estructural es crítico, pues generalmente es debido a un despegue repentino y frágil de la banda del refuerzo FRP originado en grietas intermedias causadas por la flexión. La detección de este despegue en su fase inicial es fundamental para prevenir fallos futuros, que pueden ser catastróficos. Inicialmente, se lleva a cabo una revisión del método de la Impedancia Electro-Mecánica (EMI), de cara a exponer sus capacidades para la detección de daño. Una vez la tecnología apropiada es seleccionada, lo que incluye un analizador de impedancias así como novedosos sensores PZT para monitorización inteligente, se ha diseñado un procedimiento automático basado en los registros de impedancias de distintas estructuras de laboratorio. Basándonos en el hecho de que las mediciones de impedancias son posibles gracias a una colocación adecuada de una red de sensores PZT, la estimación de la presencia de daño se realiza analizando los resultados de distintos indicadores de daño obtenidos de la literatura. Para que este proceso sea automático y que no sean necesarios conocimientos previos sobre el método EMI para realizar un experimento, se ha diseñado e implementado un Interfaz Gráfico de Usuario, transformando la medición de impedancias en un proceso fácil e intuitivo. Se evalúa entonces el daño a través de los correspondientes índices de daño, intentando estimar no sólo su severidad, sino también su localización aproximada. El desarrollo de estos experimentos en cualquier estructura genera grandes cantidades de datos que han de ser procesados, y algunas veces los índices de daño no son suficientes para una evaluación completa de la integridad de una estructura. En la mayoría de los casos se pueden encontrar patrones de daño en los datos, pero no se tiene información a priori del estado de la estructura. En este punto, se ha hecho una importante investigación en técnicas de reconocimiento de patrones particularmente en aprendizaje no supervisado, encontrando aplicaciones interesantes en el campo de la medicina. De ahí surge una idea creativa e innovadora: detectar y seguir la evolución del daño en distintas estructuras como si se tratase de un cáncer propagándose por el cuerpo humano. En ese sentido, las lecturas de impedancias se emplean como información intrínseca de la salud de la propia estructura, de forma que se pueden aplicar las mismas técnicas que las empleadas en la investigación del cáncer. En este caso, se ha aplicado un algoritmo de clasificación jerárquica dado que ilustra además la clasificación de los datos de forma gráfica, incluyendo información cualitativa y cuantitativa sobre el daño. Se ha investigado la efectividad de este procedimiento a través de tres estructuras de laboratorio, como son una viga de aluminio, una unión atornillada de aluminio y un bloque de hormigón reforzado con FRP. La primera ayuda a mostrar la efectividad del método en sencillos escenarios de daño simple y múltiple, de forma que las conclusiones extraídas se aplican sobre los otros dos, diseñados para simular condiciones de despegue en distintas estructuras. Demostrada la efectividad del método de clasificación jerárquica de lecturas de impedancias, se aplica el procedimiento sobre las estructuras de hormigón armado reforzadas con bandas de FRP objeto de esta tesis, detectando y clasificando cada estado de daño. Finalmente, y como alternativa al anterior procedimiento, se propone un método para la monitorización continua de la interfase FRP-Hormigón, a través de una red de sensores FBG permanentemente instalados en dicha interfase. De esta forma, se obtienen medidas de deformación de la interfase en condiciones de carga continua, para ser implementadas en un modelo de optimización multiobjetivo, cuya solución se haya por medio de una expansión multiobjetivo del método Particle Swarm Optimization (PSO). La fiabilidad de este último método de detección se investiga a través de sendos ejemplos tanto numéricos como experimentales. ABSTRACT This thesis aims to develop robust and reliable damage identification methods focused on experimental structural systems, in particular Reinforced Concrete (RC) structures externally strengthened with Fiber Reinforced Polymers (FRP) strips. The failure mode of this type of structural system is critical, since it is usually due to sudden and brittle debonding of the FRP reinforcement originating from intermediate flexural cracks. Detection of the debonding in its initial stage is essential thus to prevent future failure, which might be catastrophic. Initially, a revision of the Electro-Mechanical Impedance (EMI) method is carried out, in order to expose its capabilities for local damage detection. Once the appropriate technology is selected, which includes impedance analyzer as well as novel PZT sensors for smart monitoring, an automated procedure has been design based on the impedance signatures of several lab-scale structures. On the basis that capturing impedance measurements is possible thanks to an adequately deployed PZT sensor network, the estimation of damage presence is done by analyzing the results of different damage indices obtained from the literature. In order to make this process automatic so that it is not necessary a priori knowledge of the EMI method to carry out an experimental test, a Graphical User Interface has been designed, turning the impedance measurements into an easy and intuitive procedure. Damage is then assessed through the analysis of the corresponding damage indices, trying to estimate not only the damage severity, but also its approximate location. The development of these tests on any kind of structure generates large amounts of data to be processed, and sometimes the information provided by damage indices is not enough to achieve a complete analysis of the structural health condition. In most of the cases, some damage patterns can be found in the data, but none a priori knowledge of the health condition is given for any structure. At this point, an important research on pattern recognition techniques has been carried out, particularly on unsupervised learning techniques, finding interesting applications in the medicine field. From this investigation, a creative and innovative idea arose: to detect and track the evolution of damage in different structures, as if it were a cancer propagating through a human body. In that sense, the impedance signatures are used to give intrinsic information of the health condition of the structure, so that the same clustering algorithms applied in the cancer research can be applied to the problem addressed in this dissertation. Hierarchical clustering is then applied since it also provides a graphical display of the clustered data, including quantitative and qualitative information about damage. The performance of this approach is firstly investigated using three lab-scale structures, such as a simple aluminium beam, a bolt-jointed aluminium beam and an FRP-strengthened concrete specimen. The first one shows the performance of the method on simple single and multiple damage scenarios, so that the first conclusions can be extracted and applied to the other two experimental tests, which are designed to simulate a debonding condition on different structures. Once the performance of the impedance-based hierarchical clustering method is proven to be successful, it is then applied to the structural system studied in this dissertation, the RC structures externally strengthened with FRP strips, where the debonding failure in the interface between the FRP and the concrete is successfully detected and classified, proving thus the feasibility of this method. Finally, as an alternative to the previous approach, a continuous monitoring procedure of the FRP-Concrete interface is proposed, based on an FBGsensors Network permanently deployed within that interface. In this way, strain measurements can be obtained under controlled loading conditions, and then they are used in order to implement a multi-objective model updating method solved by a multi-objective expansion of the Particle Swarm Optimization (PSO) method. The feasibility of this last proposal is investigated and successfully proven on both numerical and experimental RC beams strengthened with FRP.

Analysis of quality of experience in 3D video systems

Esta tesis presenta un estudio exhaustivo sobre la evaluación de la calidad de experiencia (QoE, del inglés Quality of Experience) percibida por los usuarios de sistemas de vídeo 3D, analizando el impacto de los efectos introducidos por todos los elementos de la cadena de procesamiento de vídeo 3D. Por lo tanto, se presentan varias pruebas de evaluación subjetiva específicamente diseñadas para evaluar los sistemas considerados, teniendo en cuenta todos los factores perceptuales relacionados con la experiencia visual tridimensional, tales como la percepción de profundidad y la molestia visual. Concretamente, se describe un test subjetivo basado en la evaluación de degradaciones típicas que pueden aparecer en el proceso de creación de contenidos de vídeo 3D, por ejemplo debidas a calibraciones incorrectas de las cámaras o a algoritmos de procesamiento de la señal de vídeo (p. ej., conversión de 2D a 3D). Además, se presenta el proceso de generación de una base de datos de vídeos estereoscópicos de alta calidad, disponible gratuitamente para la comunidad investigadora y que ha sido utilizada ampliamente en diferentes trabajos relacionados con vídeo 3D. Asimismo, se presenta otro estudio subjetivo, realizado entre varios laboratorios, con el que se analiza el impacto de degradaciones causadas por la codificación de vídeo, así como diversos formatos de representación de vídeo 3D. Igualmente, se describen tres pruebas subjetivas centradas en el estudio de posibles efectos causados por la transmisión de vídeo 3D a través de redes de televisión sobre IP (IPTV, del inglés Internet Protocol Television) y de sistemas de streaming adaptativo de vídeo. Para estos casos, se ha propuesto una innovadora metodología de evaluación subjetiva de calidad vídeo, denominada Content-Immersive Evaluation of Transmission Impairments (CIETI), diseñada específicamente para evaluar eventos de transmisión simulando condiciones realistas de visualización de vídeo en ámbitos domésticos, con el fin de obtener conclusiones más representativas sobre la experiencia visual de los usuarios finales. Finalmente, se exponen dos experimentos subjetivos comparando varias tecnologías actuales de televisores 3D disponibles en el mercado de consumo y evaluando factores perceptuales de sistemas Super Multiview Video (SMV), previstos a ser la tecnología futura de televisores 3D de consumo, gracias a una prometedora visualización de contenido 3D sin necesidad de gafas específicas. El trabajo presentado en esta tesis ha permitido entender los factores perceptuales y técnicos relacionados con el procesamiento y visualización de contenidos de vídeo 3D, que pueden ser de utilidad en el desarrollo de nuevas tecnologías y técnicas de evaluación de la QoE, tanto metodologías subjetivas como métricas objetivas. ABSTRACT This thesis presents a comprehensive study of the evaluation of the Quality of Experience (QoE) perceived by the users of 3D video systems, analyzing the impact of effects introduced by all the elements of the 3D video processing chain. Therefore, various subjective assessment tests are presented, particularly designed to evaluate the systems under consideration, and taking into account all the perceptual factors related to the 3D visual experience, such as depth perception and visual discomfort. In particular, a subjective test is presented, based on evaluating typical degradations that may appear during the content creation, for instance due to incorrect camera calibration or video processing algorithms (e.g., 2D to 3D conversion). Moreover, the process of generation of a high-quality dataset of 3D stereoscopic videos is described, which is freely available for the research community, and has been already widely used in different works related with 3D video. In addition, another inter-laboratory subjective study is presented analyzing the impact of coding impairments and representation formats of stereoscopic video. Also, three subjective tests are presented studying the effects of transmission events that take place in Internet Protocol Television (IPTV) networks and adaptive streaming scenarios for 3D video. For these cases, a novel subjective evaluation methodology, called Content-Immersive Evaluation of Transmission Impairments (CIETI), was proposed, which was especially designed to evaluate transmission events simulating realistic home-viewing conditions, to obtain more representative conclusions about the visual experience of the end users. Finally, two subjective experiments are exposed comparing various current 3D displays available in the consumer market, and evaluating perceptual factors of Super Multiview Video (SMV) systems, expected to be the future technology for consumer 3D displays thanks to a promising visualization of 3D content without specific glasses. The work presented in this thesis has allowed to understand perceptual and technical factors related to the processing and visualization of 3D video content, which may be useful in the development of new technologies and approaches for QoE evaluation, both subjective methodologies and objective metrics.

A study of the mechanical behaviour of the human aortic artery by means of non-linear finite element models

En la presente tesis desarrollamos una estrategia para la simulación numérica del comportamiento mecánico de la aorta humana usando modelos de elementos finitos no lineales. Prestamos especial atención a tres aspectos claves relacionados con la biomecánica de los tejidos blandos. Primero, el análisis del comportamiento anisótropo característico de los tejidos blandos debido a las familias de fibras de colágeno. Segundo, el análisis del ablandamiento presentado por los vasos sanguíneos cuando estos soportan cargas fuera del rango de funcionamiento fisiológico. Y finalmente, la inclusión de las tensiones residuales en las simulaciones en concordancia con el experimento de apertura de ángulo. El análisis del daño se aborda mediante dos aproximaciones diferentes. En la primera aproximación se presenta una formulación de daño local con regularización. Esta formulación tiene dos ingredientes principales. Por una parte, usa los principios de la teoría de la fisura difusa para garantizar la objetividad de los resultados con diferentes mallas. Por otra parte, usa el modelo bidimensional de Hodge-Petruska para describir el comportamiento mesoscópico de los fibriles. Partiendo de este modelo mesoscópico, las propiedades macroscópicas de las fibras de colágeno son obtenidas a través de un proceso de homogenización. En la segunda aproximación se presenta un modelo de daño no-local enriquecido con el gradiente de la variable de daño. El modelo se construye a partir del enriquecimiento de la función de energía con un término que contiene el gradiente material de la variable de daño no-local. La inclusión de este término asegura una regularización implícita de la implementación por elementos finitos, dando lugar a resultados de las simulaciones que no dependen de la malla. La aplicabilidad de este último modelo a problemas de biomecánica se estudia por medio de una simulación de un procedimiento quirúrgico típico conocido como angioplastia de balón. In the present thesis we develop a framework for the numerical simulation of the mechanical behaviour of the human aorta using non-linear finite element models. Special attention is paid to three key aspects related to the biomechanics of soft tissues. First, the modelling of the characteristic anisotropic behaviour of the softue due to the collagen fibre families. Secondly, the modelling of damage-related softening that blood vessels exhibit when subjected to loads beyond their physiological range. And finally, the inclusion of the residual stresses in the simulations in accordance with the opening-angle experiment The modelling of damage is addressed with two major and different approaches. In the first approach a continuum local damage formulation with regularisation is presented. This formulation has two principal ingredients. On the one hand, it makes use of the principles of the smeared crack theory to avoid the mesh size dependence of the structural response in softening. On the other hand, it uses a Hodge-Petruska bidimensional model to describe the fibrils as staggered arrays of tropocollagen molecules, and from this mesoscopic model the macroscopic material properties of the collagen fibres are obtained using an homogenisation process. In the second approach a non-local gradient-enhanced damage formulation is introduced. The model is built around the enhancement of the free energy function by means of a term that contains the referential gradient of the non-local damage variable. The inclusion of this term ensures an implicit regularisation of the finite element implementation, yielding mesh-objective results of the simulations. The applicability of the later model to biomechanically-related problems is studied by means of the simulation of a typical surgical procedure, namely, the balloon angioplasty.

Business, development and inclusive supply chains. Exploring pathways for the sustainable incorporation of the poor as suppliers in agrifood supply chains

El panorama global está cambiando, y esto influye sobre la forma en la que entendemos y tratamos de alcanzar un desarrollo humano sostenible. El crecimiento de la población conlleva una mayor presión sobre los recursos, pero también supone una mayor cantidad de mano de obra y de talento; la concentración en áreas urbanas está cambiando las dinámicas sociales y desafiando los canales de comercialización tradicionales, pero también genera nuevos mercados y fomenta la innovación; los cambios en la economía global están reduciendo los tradicionales desequilibrios de poder entre los países occidentales y el resto del mundo; y las crecientes interconexiones crean nuevos riesgos pero también oportunidades para lanzar iniciativas de alcance global. Todas estas tendencias nos están obligando a repensar qué es el desarrollo humano y de qué manera deberíamos afrontar el reto de la pobreza. Es comúnmente aceptado que la globalización implica interdependencia y que, para conseguir un desarrollo humano sostenible, la colaboración entre actores de distintos ámbitos es necesaria. Se observa una creciente convergencia de temas, intereses y soluciones en torno al desarrollo sostenible, incluso en diferentes países y sectores, lo que está facilitando la colaboración estratégica entre empresas, gobiernos y sociedad civil. Existen pocas duda a día de hoy sobre el papel fundamental que las empresas deben desempeñar en la transición mundial hacia la sostenibilidad ambiental y la erradicación de la pobreza. Las empresas están evolucionando desde un enfoque tradicional centrado en la maximización de beneficios económicos hacia un enfoque holístico que integra la sostenibilidad y la responsabilidad social como parte del núcleo de negocio de las compañías. En el ámbito medioambiental, muchas empresas ya han comenzado a actuar y tratan de reducir sus emisiones, sus desechos y su consumo de energía. Sin embargo la contribución de las empresas a la reducción de la pobreza no está tan clara. Actualmente en torno a 1,2 miles de millones de personas viven en situación de extrema pobreza. La mayoría de estas personas aún vive en zonas rurales donde la mayor parte de la población activa trabaja en el sector agrícola. Por lo tanto, mejorar las oportunidades y reducir los riesgos de los productores más vulnerables en el sector de la agricultura puede ser un motor de desarrollo rural y reducción de la pobreza, especialmente en países de bajo nivel de desarrollo cuyas economías están fundamentalmente basadas en la agricultura. Algunas empresas comienzan a incluir a los pobres en sus operaciones como consumidores, proveedores y emprendedores. Esta tesis se centra en las potenciales oportunidades relacionadas con la incorporación sostenible de los pobres como proveedores de productos y/o de mano de obra. La colaboración entre empresas y productores vulnerables de países en desarrollo es un tema relativamente nuevo y todavía poco estudiado. La pregunta que guía esta tesis es: “¿Cómo pueden las empresas facilitar la inclusión sostenible en cadenas de suministro de productores vulnerables de los países menos desarrollados?”. Para responder a la pregunta anterior, la autora ha aplicado una metodología de casos de estudio. Esta metodología se considera apropiada porque la investigación sobre cadenas de suministro inclusivas es todavía escasa y porque es necesario entender en profundidad un fenómeno de la vida real, y para ello es fundamental conocer su contexto. En primer lugar, se realiza una revisión de literatura para identificar las proposiciones y los constructos teóricos que guiarán la posterior recogida de datos. La revisión de literatura se divide en dos partes: una más general que explora la dimensión social de la sostenibilidad en cadenas de suministro, y una más específica que se centra en la incorporación de los pobres como proveedores en cadenas de suministro. A lo largo de la última década, ha habido un crecimiento exponencial de los estudios académicos sobre la sostenibilidad de las cadenas de suministro, pero la mayoría de los esfuerzos se han dirigido hacia la dimensión medioambiental de la sostenibilidad. Por lo tanto la revisión de literatura, que se presenta en la Sección 3.1 (página 35) y que profundiza en la sostenibilidad social de las cadenas de suministro, puede considerarse una contribución en sí misma. Esta revisión de literatura revela que la investigación sobre aspectos sociales en cadenas de suministro está cobrando impulso en distintas áreas de conocimiento, principalmente en los ámbitos de investigación sobre “gestión de cadenas de suministro”, “responsabilidad social corporativa” y “estudios del desarrollo”. La investigación existente sobre sostenibilidad social de cadenas de suministro se centra en tres temas: aclarar la definición de sostenibilidad social; analizar la implementación de estrategias de sostenibilidad social en cadenas de suministro; y estudiar el apoyo de las em presas líderes a proveedores vulnerables para facilitar su transición hacia la sostenibilidad. Un marco conceptual que resume los principales hallazgos de esta primera parte de la revisión de literatura es planteado en la Figura 7 (página 48). No obstante, en el área de investigación que está emergiendo en torno a la sostenibilidad social de las cadenas de suministro, los estudios relacionados con la reducción de la pobreza son aún escasos. Además se aprecia una falta de contribuciones desde y sobre los países menos desarrollados, así como una clara tendencia a reflejar la visión de las empresas líderes de las cadenas de suministro, olvidando la perspectiva de los proveedores. La segunda parte de la revisión de literatura presentada en la Sección 3.2 (página 51) profundiza en tres líneas de investigación que exploran, desde distintas perspectivas, la inclusión de los pobres en cadenas de suministro. Estas líneas son “Global Value Chains” (GVC), “Base of the Pyramid” (BoP) y “Sustainable Supply Chain Management” (SSCM). La investigación en GVC analiza las cadenas de suministro desde la perspectiva de la globalización económica y el comercio internacional, poniendo especial énfasis en las implicaciones para los países en desarrollo y las comunidades vulnerables. GVC caracteriza las cadenas de suministro según la forma en la que son gobernadas, las oportunidades de mejora que existen para los productores que forman parte de la cadena y el grado de inclusión o exclusión de las comunidades más pobres y vulnerables. La investigación en BoP explora las relaciones comerciales entre empresas y comunidades pobres. La premisa fundamental del concepto BoP es la posibilidad de combinar la generación de beneficios con la reducción de la pobreza. La propuesta original es que mediante la venta de productos y servicios a las comunidades pobres de países en desarrollo, la pobreza puede ser reducida al tiempo que las empresas incrementan sus beneficios, especialmente las grandes empresas multinacionales. Esta idea ha ido evolucionando y, a día de hoy, los investigadores BoP consideran la incorporación de los pobres no sólo como consumidores sino también como empleados, proveedores y co-creadores. La investigación en SSCM ha estado fundamentalmente orientada al estudio de la dimensión medioambiental de la sostenibilidad de cadenas de suministro. Sin embargo, la creciente externalización de la producción a países en desarrollo y las demandas de los grupos de interés para que las empresas aborden todos los aspectos de la sostenibilidad han llevado a los académicos de SSCM a reconocer la importancia de integrar asuntos relacionados con la reducción de la pobreza en sus investigaciones. Algunos estudios comienzan a apuntar los principales retos a los que se enfrentan las empresas para colaborar con productores vulnerables en sus cadenas de suministro. Estos retos son: falta de comunicación, altos costes de transacción y el incremento de la complejidad de las operaciones. Las contribuciones de estas tres líneas de investigación son complementarias para el estudio de las cadenas de suministro inclusivas. Sin embargo, raramente han sido consideradas conjuntamente, ya que pertenecen a ámbitos de conocimiento distintos. Esta tesis integra las aportaciones de GVC, BoP y SSCM en un marco conceptual para la creación y gestión de cadenas de suministro inclusivas. Este marco conceptual para cadenas de suministro inclusivas queda representado en la Figura 9 (página 68). El marco conceptual refleja las motivaciones que llevan a las empresas a colaborar con productores vulnerables, los retos a los que se enfrentan al hacerlo, y los caminos o estrategias que están siguiendo para construir y operar cadenas de suministro inclusivas de manera que sean beneficiosas tanto para la empresa como para los productores vulnerables. A fin de validar y refinar el marco conceptual propuesto, tres casos de estudio se llevan a cabo. Las cadenas de suministro analizadas por los casos de estudio pertenecen al sector agrícola y sus principales proveedores se encuentran en países de África subsahariana. Múltiples métodos de recolección de datos y triangulación son utilizados para mejorar la fiabilidad de los datos. La autora desarrolló trabajos de campo en Senegal, Etiopía y Tanzania. Estos viajes permitieron enriquecer el proceso de recogida de información mediante entrevistas semiestructuradas y conversaciones informales con los principales actores de la cadena de suministro y mediante la observación directa de los procesos y las interacciones entre productores vulnerables y empresas. El Caso de estudio A (Sección 5.1 en página 96) es un caso de estudio único. Analiza la cadena de suministro local de verduras en Senegal. La organización focal es Manobi, una empresa senegalesa que provee servicios de bajo coste a emprendedores locales del sector agrícola. El Caso de estudio A proporciona un interesante análisis del funcionamiento de una cadena de suministro local en un país en desarrollo y muestra como la provisión de servicios profesionales puede mejorar el desempeño de productores vulnerables. El Caso de estudio B (Sección 5.2 en página 122) es un caso de estudio único. Analiza la cadena de suministro global de flor cortada con origen en Etiopía. La organización focal es EHPEA, la Asociación Etíope de Productores y Exportadores Hortícolas, cuya misión es promover y salvaguardar la posición competitiva del sector agrícola etíope en el mercado global. El Caso de estudio B ayuda a comprender mejor la perspectiva de los proveedores respecto a los requerimiento de sostenibilidad del mercado global. También muestra cómo la inclusión de los productores en el proceso de desarrollo de un estándar privado facilita su implementación posterior. El Caso de estudio C (Sección 5.3 en página 143) es un caso de estudio múltiple. Analiza la cadena de suministro global de café especial con origen en Tanzania. Las organizaciones focales son comerciantes que conectan de manera directa a pequeños agricultores de café en países en desarrollo con empresas tostadoras de café en países desarrollados. El Caso de estudio C muestra cómo un pequeño agricultor puede proveer un producto “premium” al mercado global, y participar en un segmento diferenciado del mercado a través de una cadena de suministro transparente y eficiente. Las aportaciones empíricas de los casos de estudio ayudan a validar y mejorar el marco conceptual sobre cadenas de suministro inclusivas (ver discusión en el Capítulo 6 en página 170). El resultado es la propuesta de una nueva versión del marco conceptual representado en la Figura 40 (página 195). Los casos de estudio también proporcionan interesantes aportaciones en relación a la gestión de cadenas de suministro inclusivas y muestran las perspectivas de distintos actores implicados. Esta tesis arroja luz sobre el papel de las empresas en la creación y la gestión de cadenas de suministro inclusivas llevando a cabo una revisión de literatura multidisciplinar y analizando tres casos de estudio en países africanos. Como resultado, esta tesis presenta una serie de contribuciones empíricas y teóricas al ámbito de investigación emergente en torno a las cadenas de suministro inclusivas (Capítulo 7). Esta tesis también pretende ser útil a profesionales que deseen facilitar la incorporación de los pobres como proveedores en condiciones justas y beneficiosas. ABSTRACT The global outlook is changing, and this is influencing the way we understand and try to achieve sustainable human development. Population growth entails increasing pressure over resources, but it also provides greater workforce and talent; concentration in urban areas is changing social dynamics and challenging traditional marketing channels, but also creating news markets and driving innovation; the global economy shift is rebalancing the traditional power imbalance between Western countries and the rest of the world, making new opportunities to arise; and interconnections and global interdependence create new risks but also opportunities for launching initiatives with a global reach. All these trends are impelling us to rethink what development is and in which way poverty alleviation should be approached. It is generally agreed that globalization implies interdependence and, in order to achieve sustainable human development, collaboration of all actors is needed. A convergence of issues, interests and solutions related to sustainable development is being observed across countries and sectors, encouraging strategic collaboration among companies, governments and civil society. There is little doubt nowadays about the crucial role of the private sector in the world’s path towards environmental sustainability and poverty alleviation. Businesses are evolving from a “business as usual” stance to a more sustainable and responsible approach. In the environmental arena, many companies have already “walk the talk”, implementing environmental management systems and trying to reduce emissions and energy consumption. However, regarding poverty alleviation, their contribution is less clear. There are around 1.2 billion people living in extreme poverty. Most of this people still live in rural areas where the agricultural sector employs a big part of the active population. Therefore, improving opportunities and reducing risks for vulnerable producers in the agri-food sector can be a primary engine of rural development and poverty alleviation, particularly in the poor, agriculture-based economies of least developed countries. Some companies are beginning to include the poor into their operations as consumers, suppliers and entrepreneurs. This thesis focuses specifically on the potential opportunities related to the sustainable incorporation of the poor as suppliers of products and/or labor. Business collaboration with vulnerable producers in developing countries is a relatively new trend and it is still understudied. The overall question guiding this thesis is: “How can businesses facilitate the sustainable inclusion of vulnerable producers from least developed countries into supply chains?”. In order to answer the research question, the author has applied a case study research strategy. This methodology is considered appropriate because research about inclusive supply chains is still at an early stage, and because there is a need to understand a real-life phenomenon in depth, but such understanding encompasses important contextual conditions. First, a literature review is conducted, in order to identify the research propositions and theoretical constructs that will guide the data collection. The literature review is divided in two parts: a more general one that explores the social dimension of sustainability of supply chains, and a more specific one that focuses on the incorporation of the poor as suppliers in supply chains. During the last decade, there has been an exponential growth of studies in the field of supply chain sustainability, but research efforts have traditionally been directed towards the analysis of the environmental dimension. Therefore, the literature review presented in Section 3.1 (page 35) that delves into social sustainability of supply chains can be considered a contribution in itself. This literature review reveals that the investigation of social issues in supply chains is gaining momentum and comes from different academic disciplines, namely Supply Chain Management, Corporate Social Responsibility and Development Studies. Existing research about social sustainability of supply chains focuses on three issues: clarify the definition of social sustainability; analyze the implementation of social sustainability strategies in supply chains; and study lead companies’ support to vulnerable suppliers in their transition towards sustainability. A conceptual framework that outlines the main findings that emerge from this first part of literature review is proposed in Figure 7 (page 48). Nevertheless, in this nascent field of social sustainability of supply chains, studies related to poverty alleviation are still scarce. Moreover, a lack of contributions from and about least developed countries has been observed, as well as a tendency to reflect on the lead firms’ standpoint, neglecting the suppliers’ perspective. The second part of the literature review (Section 3.2 in page 51) delves into three research streams that are exploring the inclusion of the poor into supply chains from different viewpoints. These research streams are Global Value Chains (GVC), Base of the Pyramid (BoP) and Sustainable Supply Chain Management (SSCM). GVC research discusses the dynamics of economic globalization and international trade, putting special emphasis in the implications for developing countries and vulnerable communities. GVC characterizes supply chains by the way they are governed, the upgrading opportunities that exist for producers in the chain and the degree of inclusion or exclusion of impoverished communities. BoP research explores trading relationships between businesses and impoverished communities. The core premise of the BoP concept is the possibility to combine profits with poverty alleviation. The original BoP proposition is that by marketing innovative products and services to poor communities in developing countries, poverty would be reduced and companies would increase their benefits, especially multinational companies. This idea has evolved to consider the incorporation of the poor to business activities not only as consumers, but also as employees, entrepreneurs and co-creators. The SSCM school of thought has mainly focused on studying the environmental dimension of supply chain sustainability, neglecting the consideration of the social perspective. However, in recent years, increasing outsourcing of production to developing countries and stakeholders’ demands for a more holistic approach to business sustainability have led SSCM scholars to acknowledge the importance of integrating poverty concerns in this field’s research agenda. Some SSCM studies identify the main operational challenges for companies which engage with vulnerable suppliers in their supply chains: missing communication, higher transactional and operational costs and increased complexity. Contributions from these three research streams are complementary for the study of inclusive supply chains. However, they have been rarely considered together, since they belong to different research areas. This thesis seeks to play a dovetailing role in this scenario by proposing a conceptual framework for creating and operating inclusive supply chains that builds on contributions from GVC, SSCM and BoP research. This framework for inclusive supply chains is depicted in Figure 9 (page 68), and explains the motivations that drive businesses to collaborate with vulnerable suppliers, the chal lenges they face in doing so, and the pathways they are following in order to build and operate inclusive supply chains profitably for both buying companies and vulnerable suppliers. In order to validate and refine the proposed framework, three case studies are carried out. The supply chains analyzed by the case studies belong to the agri-food sector and source from Sub-Saharan African countries. Multiple data collection methods and triangulation are used in order to improve reliability of findings. The author carried out field work in Senegal, Ethiopia and Tanzania. These travels enriched the data collection process, providing semi-structured interviews and informal conversations with the main actors in the supply chains, as well as direct observation of processes and interactions among companies and vulnerable suppliers. Case study A (Section 5.1 in page 96) is a single case study. It analyzes a local supply chain in Senegal providing vegetables to the local market. The focal organization is Manobi, a Senegalese inclusive business which provides affordable ICT services to local entrepreneurs in the agri-food sector. Case study A provides interesting insights into the dynamics of local supply chains and how professional services can help to improve their performance. Case study B (Section 5.2 in page 122) is a single case study. It analyzes a global supply chain with origin in Ethiopia providing cut flowers to the global commodity market. The focal organization is EHPEA, Ethiopian Horticulture Producers and Exporters Association, whose mission is to promote and safeguard the competitive position of the Ethiopian horticulture sector within the global market. Case study B helps to better understand the suppliers’ perspective regarding global market sustainability requirements and shows how the inclusion of suppliers in the process of development of a private standard has a positive impact in its implementation. Case study C (Section 5.3 in page 143) is a multiple case study. It analyzes a global supply chain with origin in Tanzania providing coffee to the global niche market of specialty coffee. The focal organizations are traders who are directly connecting smallholder coffee farmers in developing countries to coffee roasters in developed countries. Case study C shows how smallholder farmers can supply a premium product and be incorporated in a differentiated market segment through a transparent and efficient supply chain. The empirical findings from the case studies help to validate and refine the conceptual framework (see discussion in Chapter 6). The proposal of a new version of the conceptual framework is depicted in Figure 40 (page 195). The case studies also provide interesting insights related to the management of inclusive supply chains and show the perspectives of the different actors involved. This thesis sheds some light on the role of businesses in the creation and operation of inclusive supply chains by carrying out a cross-disciplinary literature review and analyzing three case studies in African countries. In doing so, this thesis presents a series of theoretical and empirical contributions to the emerging academic field of inclusive supply chains (Chapter 7). This thesis also intends to be useful to practitioners willing to improve the incorporation of the poor as suppliers in fair and profitable conditions.

Vivienda y Revolución. El Concurso entre Camaradas de la OSA, la Sección de Tipificación del Stroykom y la Casa Experimental de Transición Narkomfin (1926-1930) = Housing and Revolution. OSA’s Comradely Competition, Typification Section of the Stroykom and Narkomfin Experimental Transitional House (1926-1930)

La cuestión del asentamiento socialista en la URSS durante la década de 1920 estuvo caracterizada por el objetivo de definir y establecer un estado socialista en términos políticos, sociales y económicos. En este contexto de inestabilidad y cambio, un grupo de arquitectos pertenecientes a la Asociación de Arquitectos Contemporáneos, OSA, y liderado por Moisey Ginzburg, abordó el tema de la vivienda obrera asumiendo la responsabilidad y el compromiso por alcanzar un nuevo orden social. Su misión no consistió únicamente en solucionar el problema del alojamiento para los trabajadores en las grandes ciudades soviéticas, sino en redefinirlo como el marco adecuado para una sociedad sometida a un cambio sin precedentes que, al mismo tiempo y en un proceso dialéctico, debía contribuir a la construcción de esa nueva sociedad. La respuesta dada por la OSA trascendió el diseño inmediato bajo los estándares modernos establecidos en Occidente y tomó forma en un proceso de investigación que habría de prolongarse durante cinco años. Este trabajo, que culminó con la construcción y puesta en crisis de la Casa Narkomfin, se desarrolló en tres aproximaciones sucesivas. La primera, de carácter conceptual, consideró la participación ciudadana, así como de especialistas independientes, formalizándose en el Concurso entre Camaradas convocado por la OSA en 1926. La segunda aproximación al problema de la vivienda obrera se articuló a través de la investigación llevada a cabo por la Sección de Tipificación del Stroykom, esta vez desde premisas científicas y metodológicas. Finalmente, las conclusiones alcanzadas fueron transferidas a la práctica arquitectónica por medio de la construcción de seis Casas Experimentales de Transición, entre las que destacó la Casa Narkomfin. Este último acercamiento, de carácter empírico, ha sido tradicionalmente examinado por los expertos como un hecho aislado. Sin embargo, su estudio debe trascender necesariamente el genio del autor-creador en favor del proceso de investigación al que pertenece. En esta tesis, la Casa Narkomfin no se presenta sólo como el paradigma de vivienda soviética de vanguardia al que estamos acostumbrados, sino como un prototipo que recoge los principios y conclusiones alcanzados en las aproximaciones conceptuales y científicas precedentes. Únicamente desde este punto de vista cobra sentido la consideración de Ginzburg sobre su propio edificio como un medio propositivo y no impositivo: un proyecto concebido como una herramienta de transición hacia una sociedad más avanzada. ABSTRACT The question of mass housing in the USSR during the Twenties was marked by the drive to define and establish a socialist state in political, social and economic terms. In this context of instability and change, a group of architects gathered together under the Association of Contemporary Architects, OSA, led by Moisey Ginzburg, to address the issue of mass housing, thus taking on the responsibility and being committed to creating a new social order. Their quest not only involved solving the problem of housing for workers in large Soviet cities, but also redefining this solution as an appropriate framework for a society undergoing dramatic changes which, at the same time and in a dialectical process, would contribute to the creation of this new society. The solution provided by OSA transcended Modern standards of immediate design set by the West and was the result of a research process that would last five years. This work culminated in the construction of Narkomfin House and its self-criticism, developed in three successive approaches. The first was conceptual, being formalized in the Comradely Competition held by the OSA in 1926 and taking into account the participation of citizens and independent experts. The second approach to the problem of mass housing involved research developed by the Typification Section of the Stroykom, this time under scientific and methodological premises. Finally, the conclusions reached were put in practice with the construction of six Experimental Transitional Houses of which the most notable is Narkomfin House. This third empirical approach has traditionally been examined by scholars in isolation. However, its study must necessarily transcend the genius of the author-creator and involve the research process of which it is part. In this thesis, Narkomfin House is presented not only as the paradigm in Soviet housing avant-garde we are used to, but also as a prototype reflecting the principles and conclusions reached in the preceding conceptual and scientific approaches. Only from this point of view does Ginzburg’s understanding of his own building as a proactive and non-imposed environment make sense: a project conceived as a transition tool towards a more advanced society.

Activation of human monocytes induces differential resistance to apoptosis with rapid down regulation of caspase-8/FLICE

Cells of the monocyte/macrophage lineage play a central role in both innate and acquired immunity of the host. However, the acquisition of functional competence and the ability to respond to a variety of activating or modulating signals require maturation and differentiation of circulating monocytes and entail alterations in both biochemical and phenotypic profiles of the cells. The process of activation also confers survival signals essential for the functional integrity of monocytes enabling the cells to remain viable in microenvironments of immune or inflammatory lesions that are rich in cytotoxic inflammatory mediators and reactive free-radical species. However, the molecular mechanisms of activation-induced survival signals in monocytes remain obscure. To define the mechanistic basis of activation-induced resistance to apoptosis in human monocytes at the molecular level, we evaluated the modulation of expression profiles of genes associated with the cellular apoptotic pathways upon activation and demonstrate the following: (i) activation results in selective resistance to apoptosis particularly to that induced by signaling via death receptors and DNA damage; (ii) concurrent with activation, the most apical protease in the death receptor pathway, caspase-8/FLICE is rapidly down-regulated at the mRNA level representing a novel regulatory mechanism; and (iii) activation of monocytes also leads to dramatic induction of the Bfl-1 gene, an anti apoptotic member of the Bcl-2 family. Our findings thus provide a potential mechanistic basis for the activation-induced resistance to apoptosis in human monocytes.

Viral mediated expression of insulin-like growth factor I blocks the aging-related loss of skeletal muscle function

During the aging process, mammals lose up to a third of their skeletal muscle mass and strength. Although the mechanisms underlying this loss are not entirely understood, we attempted to moderate the loss by increasing the regenerative capacity of muscle. This involved the injection of a recombinant adeno-associated virus directing overexpression of insulin-like growth factor I (IGF-I) in differentiated muscle fibers. We demonstrate that the IGF-I expression promotes an average increase of 15% in muscle mass and a 14% increase in strength in young adult mice, and remarkably, prevents aging-related muscle changes in old adult mice, resulting in a 27% increase in strength as compared with uninjected old muscles. Muscle mass and fiber type distributions were maintained at levels similar to those in young adults. We propose that these effects are primarily due to stimulation of muscle regeneration via the activation of satellite cells by IGF-I. This supports the hypothesis that the primary cause of aging-related impairment of muscle function is a cumulative failure to repair damage sustained during muscle utilization. Our results suggest that gene transfer of IGF-I into muscle could form the basis of a human gene therapy for preventing the loss of muscle function associated with aging and may be of benefit in diseases where the rate of damage to skeletal muscle is accelerated.

Jac1, a mitochondrial J-type chaperone, is involved in the biogenesis of Fe/S clusters in Saccharomyces cerevisiae

A minor Hsp70 chaperone of the mitochondrial matrix of Saccharomyces cerevisiae, Ssq1, is involved in the formation or repair of Fe/S clusters and/or mitochondrial iron metabolism. Here, we report evidence that Jac1, a J-type chaperone of the mitochondrial matrix, is the partner of Ssq1 in this process. Reduced activity of Jac1 results in a decrease in activity of Fe/S containing mitochondrial proteins and an accumulation of iron in mitochondria. Fe/S enzyme activities remain low in both jac1 and ssq1 mutant mitochondria even if normal mitochondrial iron levels are maintained. Therefore, the low activities observed are not solely due to oxidative damage caused by excess iron. Rather, these molecular chaperones likely play a direct role in the normal assembly process of Fe/S clusters.

Excision of 8-oxoguanine within clustered damage by the yeast OGG1 protein

Clustered damages are formed in DNA by ionising radiation and radiomimetic anticancer agents and are thought to be biologically severe. 7,8-dihydro-8-oxoguanine (8-oxoG), a major DNA damage resulting from oxidative attack, is highly mutagenic leading to a high level of G·C→T·A transversions if not previously excised by OGG1 DNA glycosylase/AP lyase proteins in eukaryotes. However, 8-oxoG within clustered DNA damage may present a challenge to the repair machinery of the cell. The ability of yeast OGG1 to excise 8-oxoG was determined when another type of damage [dihydrothymine, uracil, 8-oxoG, abasic (AP) site or various types of single-strand breaks (SSBs)] is present on the complementary strand 1, 3 or 5 bases 5′ or 3′ opposite to 8-oxoG. Base damages have little or no influence on the excision of 8-oxoG by yeast OGG1 (yOGG1) whereas an AP site has a strong inhibitory effect. Various types of SSBs, obtained using either oligonucleotides with 3′- and 5′-phosphate termini around a gap or through conversion of an AP site with either endonuclease III or human AP endonuclease 1, strongly inhibit excision of 8-oxoG by yOGG1. Therefore, this large inhibitory effect of an AP site or a SSB may minimise the probability of formation of a double-strand break in the processing of 8-oxoG within clustered damages.

Early p53 alterations in mouse skin carcinogenesis by UVB radiation: immunohistochemical detection of mutant p53 protein in clusters of preneoplastic epidermal cells.

High levels of the p53 protein are immunohistochemically detectable in a majority of human nonmelanoma skin cancers and UVB-induced murine skin tumors. These increased protein levels are often associated with mutations in the conserved domains of the p53 gene. To investigate the timing of the p53 alterations in the process of UVB carcinogenesis, we used a well defined murine model (SKH:HR1 hairless mice) in which the time that tumors appear is predictable from the UVB exposures. The mice were subjected to a series of daily UVB exposures, either for 17 days or for 30 days, which would cause skin tumors to appear around 80 or 30 weeks, respectively. In the epidermis of these mice, we detected clusters of cells showing a strong immunostaining of the p53 protein, as measured with the CM-5 polyclonal antiserum. This cannot be explained by transient accumulation of the normal p53 protein as a physiological response to UVB-induced DNA damage. In single exposure experiments the observed transient CM-5 immunoreactivity lasted for only 3 days and was not clustered, whereas these clusters were still detectable as long as 56 days after 17 days of UVB exposure. In addition, approximately 70% of these patches reacted with the mutant-specific monoclonal antibody PAb240, whereas transiently induced p53-positive cells did not. In line with indicative human data, these experimental results in the hairless mouse model unambiguously demonstrate that constitutive p53 alterations are causally related to chronic UVB exposure and that they are a very early event in the induction of skin cancer by UVB radiation.