986 resultados para plant yield component
Resumo:
O principal objectivo desta tese é obter uma relação directa entre a composição dos gases liquefeitos de petróleo (GLP), propano, n-butano e isobutano, usados como aerossóis propulsores numa lata de poliuretano de um componente, com as propriedades das espumas produzidas por spray. As espumas obtidas, terão de ter como requisito principal, um bom desempenho a temperaturas baixas, -10ºC, sendo por isso designadas por espumas de Inverno. Uma espuma é considerada como tendo um bom desempenho se não apresentar a -10/-10ºC (temperatura lata/ spray) glass bubbles, base holes e cell collapse. As espumas deverão ainda ter densidades do spray no molde a +23/+23ºC abaixo dos 30 g/L, um rendimento superior a 30 L, boa estabilidade dimensional e um caudal de espuma a +5/+5ºC superior a 5 g/s. Os ensaios experimentais foram realizados a +23/+23ºC, +5/+5ºC e a -10/-10ºC. A cada temperatura, as espumas desenvolvidas, foram submetidas a testes que permitiram determinar a sua qualidade. Testes esses que incluem os designados por Quick Tests (QT): o spray no papel e no molde das espumas nas referidas temperaturas. As amostras do papel e no molde são especialmente analisadas, quanto, às glass bubbles, cell collapse, base holes, cell structur e, cutting shrinkage, para além de outras propriedades. Os QT também incluem a análise da densidade no molde (ODM) e o estudo do caudal de espumas. Além dos QT foram realizados os testes da estabilidade dimensional das espumas, testes físicos de compressão e adesão, testes de expansão das espumas após spray e do rendimento por lata de espuma. Em todos os ensaios foi utilizado um tubo adaptador colocado na válvula da lata como método de spray e ainda mantida constante a proporção das matérias-primas (excepto os gases, em estudo). As experiências iniciaram-se com o estudo de GLPs presentes no mercado de aerossóis. Estes resultaram que o GLP: propano/ n-butano/ isobutano: (30/ 0/ 70 w/w%), produz as melhores espumas de inverno a -10/-10ºC, reduzindo desta forma as glass bubbles, base holes e o cell collapse produzido pelos restantes GLP usados como aerossóis nas latas de poliuretano. Testes posteriores tiveram como objectivo estudar a influência directa de cada gás, propano, n-butano e isobutano nas espumas. Para tal, foram usadas duas referências do estudo com GLP comercializáveis, 7396 (30 /0 /70 w/w %) e 7442 (0/ 0/ 100 w/w %). Com estes resultados concluí-se que o n-butano produz más propriedades nas espumas a -10/- 10ºC, formando grandes quantidades de glass bubbles, base holes e cell collapse. Contudo, o uso de propano reduz essas glass bubbles, mas em contrapartida, forma cell collapse.Isobutano, porém diminui o cell collapse mas não as glass bubbles. Dos resultados experimentais podemos constatar que o caudal a +5/+5ºC e densidade das espumas a +23/+23ºC, são influenciados pela composição do GLP. O propano e n-butano aumentam o caudal de espuma das latas e a sua densidade, ao contrário com o que acontece com o isobutano. Todavia, pelos resultados obtidos, o isobutano proporciona os melhores rendimentos de espumas por lata. Podemos concluir que os GLPs que contivessem cerca de 30 w/w % de propano (bons caudais a +5/+5ºC e menos glass bubbles a -10/-10ºC), e cerca 70 w/w % de isobutano (bons rendimentos de espumas, bem como menos cell collapse a -10/-10ºC) produziam as melhores espumas. Também foram desenvolvidos testes sobre a influência da quantidade de gás GLP presente numa lata. A análise do volume de GLP usado, foi realizada com base na melhor espuma obtida nos estudos anteriores, 7396, com um GLP (30 / 0/ 70 w/w%), e foram feitas alterações ao seu volume gás GLP presente no pré-polímero. O estudo concluiu, que o aumento do volume pode diminuir a densidade das espumas, e o seu decréscimo, um aumento da densidade. Também indico u que um mau ajuste do volume poderá causar más propriedades nas espumas. A análise económica, concluiu que o custo das espumas com mais GLP nas suas formulações, reduz-se em cerca de 3%, a quando de um aumento do volume de GLP no pré-polímero de cerca de 8 %. Esta diminuição de custos deveu-se ao facto, de um aumento de volume de gás, implicar uma diminuição na quantidade das restantes matérias-primas, com custos superiores, já que o volume útil total da lata terá de ser sempre mantido nos 750 mL. Com o objectivo de melhorar a qualidade da espuma 7396 (30/0/70 w/w %) obtida nos ensaios anteriores adicionou-se à formulação 7396 o HFC-152a (1,1-di fluoroetano). Os resultados demonstram que se formam espumas com más propriedades, especialmente a -10/-10ºC, contudo proporcionou excelentes shaking rate da lata. Através de uma pequena análise de custos não é aconselhável o seu uso pelos resultados obtidos, não proporcionando um balanço custo/benefício favorável. As três melhores espumas obtidas de todos os estudos foram comparadas com uma espuma de inverno presente no mercado. 7396 e 7638 com um volume de 27 % no prépolímero e uma composição de GLP (30/ 0 / 70 w/w%) e (13,7/ 0/ 86,3 w/w%), respectivamente, e 7690, com 37 % de volume no pré-polímero e GLP (30/ 0 / 70 w/w%), apresentaram em geral melhores resultados, comparando com a espuma benchmark . Contudo, os seus shaking rate a -10/-10ºC, de cada espuma, apresentaram valores bastante inferiores à composição benchmarking.
Resumo:
OBJECTIVE: To evaluate possible adverse reproductive outcomes in an area adjacent to a petrochemical plant in southern Brazil. METHODS: A review of 17,113 birth records of the main hospital of the municipality of Montenegro, southern Brazil, from 1983 to 1998 was carried out. Three groups of cases were selected: (1) newborns with major congenital malformations; (2) newborns with low birth weight (<2,500 g); and (3) stillborns (>500 g). A control was assigned to each case. Controls were the first newborns weighing > or = 2,500 g without malformations and of case-matching sex. Mother's residence during pregnancy was used as an exposure parameter. Statistical analyses were performed using Chi-square test or Fisher test, odds ratio, 0.05 significance level, and 95% confidence interval. RESULTS: For unadjusted analysis, it was found a correlation between low birth weight and geographical proximity of mother's residence to the petrochemical plant (OR = 1.66; 95% CI = 1.01--2.72) or residence on the way of preferential wind direction (OR = 1.62; 95% CI = 1.03--2.56). When other covariates were added in the conditional logistic regression (maternal smoking habits, chronic disease and age), there was no association. CONCLUSIONS: Despite final results were negative, low birth weight could be a good parameter of environmental contamination and should be closely monitored in the studied area.
Resumo:
In the management of solid waste, pollutants over a wide range are released with different routes of exposure for workers. The potential for synergism among the pollutants raises concerns about potential adverse health effects, and there are still many uncertainties involved in exposure assessment. In this study, conventional (culture-based) and molecular real-time polymerase chain reaction (RTPCR) methodologies were used to assess fungal air contamination in a waste-sorting plant which focused on the presence of three potential pathogenic/toxigenic fungal species: Aspergillus flavus, A. fumigatus, and Stachybotrys chartarum. In addition, microbial volatile organic compounds (MVOC) were measured by photoionization detection. For all analysis, samplings were performed at five different workstations inside the facilities and also outdoors as a reference. Penicillium sp. were the most common species found at all plant locations. Pathogenic/toxigenic species (A. fumigatus and S. chartarum) were detected at two different workstations by RTPCR but not by culture-based techniques. MVOC concentration indoors ranged between 0 and 8.9 ppm (average 5.3 ± 3.16 ppm). Our results illustrated the advantage of combining both conventional and molecular methodologies in fungal exposure assessment. Together with MVOC analyses in indoor air, data obtained allow for a more precise evaluation of potential health risks associated with bioaerosol exposure. Consequently, with this knowledge, strategies may be developed for effective protection of the workers.
Resumo:
This work addresses the treatment by nanofiltration (NF) of solutions containing NaCN and NH(4)Cl at various pH values. The NF experiments are carried out in a Lab-Unit equipped with NF-270 membranes for model solutions that are surrogates of industrial ammoniacal wastewaters generated in the coke-making processes. The applied pressure is 30 bar. The main objective is the separation of the compounds NaCN and NH(4)Cl and the optimization of this separation as a function of the pH. Membrane performance is highly dependent on solution composition and characteristics, namely on the pH. In fact, the rejection coefficients for the binary model solution containing sodium cyanide are always higher than the rejections coefficients for the ammonium chloride model solution. For ternary solutions (cyanide/ammonium/water) it was observed that for pH values lower than 9 the rejection coefficients to ammonium are well above the ones observed for the cyanides, but for pH values higher than 9.5 there is a drastic decrease in the ammonium rejection coefficients with the increase of the pH. These results take into account the changes that occur in solution, namely, the solute species that are predominant, with the increase of the pH. The fluxes of the model solutions decreased with increased pH. (C) 2010 Elsevier B.V. All rights reserved.
Resumo:
A discussion of the most interesting results obtained in our laboratories, during the supercritical CO(2) extraction of bioactive compounds from microalgae and volatile oils from aromatic plants, was carried out. Concerning the microalgae, the studies on Botryococcus braunii and Chlorella vulgaris were selected. Hydrocarbons from the first microalgae, which are mainly linear alkadienes (C(23)-C(31)) with an odd number of carbon atoms, were selectively extracted at 313 K increasing the pressure up to 30.0 MPa. These hydrocarbons are easily extracted at this pressure, since they are located outside the cellular walls. The extraction of carotenoids, mainly canthaxanthin and astaxanthin, from C. vulgaris is more difficult. The extraction yield of these components at 313 K and 35.0 MPa increased with the degree of crushing of the microalga, since they are not extracellular. On the other hand, for the extraction of volatile oils from aromatic plants, studies on Mentha pulegium and Satureja montana L were chosen. For the first aromatic plant, the composition of the volatile and essential oils was similar, the main components being the pulegone and menthone. However, this volatile oil contained small amounts of waxes, which content decreased with decreasing particle size of the plant matrix. For S. montana L it was also observed that both oils have a similar composition, the main components being carvacrol and thymol. The main difference is the relative amount of thymoquinone, which content can be 15 times higher in volatile oil. This oxygenated monoterpene has important biological activities. Moreover, experimental studies on anticholinesterase activity of supercritical extracts of S. montana were also carried out. The supercritical nonvolatile fraction, which presented the highest content of the protocatechuic, vanilic, chlorogenic and (+)-catechin acids, is the most promising inhibitor of the enzyme butyrylcholinesterase. In contrast, the Soxhlet acetone extract did not affect the activity of this enzyme at the concentrations tested. (C) 2011 Elsevier B.V. All rights reserved.
Resumo:
This paper starts with the analysis of the unusual inherence mechanism, from two aspects: accumulating and human error. We put forward twelve factors affected the decision of the emergency treatment plan in practice and summarized the evaluation index system combining with literature data. Then we screened out eighteen representative indicators by used the FDM expert questionnaire in the first phase. Hereafter, we calculated the weight of evaluation index and sorted them by the FAHP expert questionnaire, and came up with the frame of the evaluation rule by combined with the experience. In the end, the evaluation principles are concluded.
Resumo:
A growth trial with Senegalese Sole (Solea senegalensis Kaup, 1858) juveniles fed with diets containing increasing replacement levels of fishmeal by mixtures of plant protein sources was conducted over 12 weeks. Total fat contents of muscle, liver, viscera, skin, fins and head tissues were determined, as well as fatty acid profiles of muscle and liver (GC-FID analysis). Liver was the preferential local for fat deposition (5.5–10.8% of fat) followed by fins (3.4–6.7% fat). Increasing levels of plant protein in the diets seems to be related to increased levels of total lipids in the liver. Sole muscle is lean (2.4–4.0% fat), with total lipids being similar among treatments. Liver fatty acid profile varied significantly among treatments. Plant protein diets induced increased levels of C16:1 and C18:2 n -6 and a decrease in ARA and EPA levels. Muscle fatty acid profile also evidenced increasing levels of C18:2 n 6, while ARA and DHA remained similar among treatments. Substitution of fishmeal by plant protein is hence possible without major differences on the lipid content and fatty acid profile of the main edible portion of the fish – the muscle.
Resumo:
High salinity causes remarkable losses in rice productivity worldwide mainly because it inhibits growth and reduces grain yield. To cope with environmental changes, plants evolved several adaptive mechanisms, which involve the regulation of many stress-responsive genes. Among these, we have chosen OsRMC to study its transcriptional regulation in rice seedlings subjected to high salinity. Its transcription was highly induced by salt treatment and showed a stress-dose-dependent pattern. OsRMC encodes a receptor-like kinase described as a negative regulator of salt stress responses in rice. To investigate how OsRMC is regulated in response to high salinity, a salt-induced rice cDNA expression library was constructed and subsequently screened using the yeast one-hybrid system and the OsRMC promoter as bait. Thereby, two transcription factors (TFs), OsEREBP1 and OsEREBP2, belonging to the AP2/ERF family were identified. Both TFs were shown to bind to the same GCC-like DNA motif in OsRMC promoter and to negatively regulate its gene expression. The identified TFs were characterized regarding their gene expression under different abiotic stress conditions. This study revealed that OsEREBP1 transcript level is not significantly affected by salt, ABA or severe cold (5 °C) and is only slightly regulated by drought and moderate cold. On the other hand, the OsEREBP2 transcript level increased after cold, ABA, drought and high salinity treatments, indicating that OsEREBP2 may play a central role mediating the response to different abiotic stresses. Gene expression analysis in rice varieties with contrasting salt tolerance further suggests that OsEREBP2 is involved in salt stress response in rice.
Resumo:
Some previous studies have suggested that some of the volatile organic compounds (VOCs) found in composting plants may have a toxic effect that can influence, besides surroundings populations, workers from the composting plants. Impact of waste management to the environment and workers is already recognised as an environment and occupational health concerns. Several studies regarding the VOCs and bioaerosols emissions from composting have been conducted all over Europe and also in Asia. However, in Portugal the studies developed are scarce and normally VOCs are not studied and recognized as a risk factor present in this occupational setting. Consudering this, a study was developed in a Portuguese composting plant aiming to clarify if there was VOCs presence in the workplaces.
Resumo:
Fungal contamination in composting facilities has been associated with increased respiratory and skin pathologies among compost workers. In this study we aim to characterize the fungal contamination caused by Aspergillus genera within a totally indoor composting plant located in Portugal. Air samples of 50L were collected from 6 sampling sites through an impaction method. Surfaces samples were collected by swabbing the surfaces of the same indoor sites. Pre-treatment and waste screw were the sampling sites of the analyzed composting plant with the highest Aspergillus load in the air. Globally, the genus Aspergillus presented the highest prevalence both in the air from (90.6%), and surfaces from the same sampling sites (60.8%). The results obtained in this study claim the attention to the need of further research regarding the fungal contamination dur to Aspergillus genus in composting plants.
Resumo:
The handling of waste can be responsible for occupational exposure to particles and fungi. The aim of this study was to characterize exposure to particles and fungi in a composting plant. Measurements of particulate matter were performed using portable direct-reading equipment. Air samples of 50L were collected through an impaction method with a flow rate of 140L/min onto malt extract agar supplemented with chloramphenicol (0.05%). Surfaces samples were also collected. All the samples were incubated at 27ºC for 5 to 7 days. Particulate matter data showed higher contamination for PM, and PM10 sizes. Aspergillus genus presents the highest air prevalence (90.6%). Aspergillus niger (32.6%), A. fumigatus (26.5%) and A. flavus (16.3%) were the most prevalent fungi in air sampling, and Mucor sp. (39.2%), Aspergillus niger (30.9%) and A. fumigatus (28.7%) were the most found in surfaces. the results obtained claim the attention to the need of further research.
Resumo:
The handling of waste and compost that occurs frequently in composting plants (compost turning, shredding, and screening) has been shown to be responsible for the release of dust and air borne microorganisms and their compounds in the air. Thermophilic fungi, such as A. fumigatus, have been reported and this kind of contamination in composting facilities has been associated with increased respiratory symptoms among compost workers. This study intended to characterize fungal contamination in a totally indoor composting plant located in Portugal. Besides conventional methods, molecular biology was also applied to overcome eventual limitations.
Resumo:
Dissertação de Mestrado, Estudos Integrados dos Oceanos, 22 de Janeiro de 2016, Universidade dos Açores.
Resumo:
Independent component analysis (ICA) has recently been proposed as a tool to unmix hyperspectral data. ICA is founded on two assumptions: 1) the observed spectrum vector is a linear mixture of the constituent spectra (endmember spectra) weighted by the correspondent abundance fractions (sources); 2)sources are statistically independent. Independent factor analysis (IFA) extends ICA to linear mixtures of independent sources immersed in noise. Concerning hyperspectral data, the first assumption is valid whenever the multiple scattering among the distinct constituent substances (endmembers) is negligible, and the surface is partitioned according to the fractional abundances. The second assumption, however, is violated, since the sum of abundance fractions associated to each pixel is constant due to physical constraints in the data acquisition process. Thus, sources cannot be statistically independent, this compromising the performance of ICA/IFA algorithms in hyperspectral unmixing. This paper studies the impact of hyperspectral source statistical dependence on ICA and IFA performances. We conclude that the accuracy of these methods tends to improve with the increase of the signature variability, of the number of endmembers, and of the signal-to-noise ratio. In any case, there are always endmembers incorrectly unmixed. We arrive to this conclusion by minimizing the mutual information of simulated and real hyperspectral mixtures. The computation of mutual information is based on fitting mixtures of Gaussians to the observed data. A method to sort ICA and IFA estimates in terms of the likelihood of being correctly unmixed is proposed.
Resumo:
Linear unmixing decomposes a hyperspectral image into a collection of reflectance spectra of the materials present in the scene, called endmember signatures, and the corresponding abundance fractions at each pixel in a spatial area of interest. This paper introduces a new unmixing method, called Dependent Component Analysis (DECA), which overcomes the limitations of unmixing methods based on Independent Component Analysis (ICA) and on geometrical properties of hyperspectral data. DECA models the abundance fractions as mixtures of Dirichlet densities, thus enforcing the constraints on abundance fractions imposed by the acquisition process, namely non-negativity and constant sum. The mixing matrix is inferred by a generalized expectation-maximization (GEM) type algorithm. The performance of the method is illustrated using simulated and real data.