The influence of heat treatment on structures of the aggregated state of polyamide-1010

The structural parameters of the aggregated state of polyamide (PA)-1010 annealed at various temperatures were computed by means of the desmearing intensity from Smalt Angle X-ray Scattering (SAXS) measurements and by using the concept of the distance distribution function. The results indicated that the structural parameters of the aggregated state were strongly dependent upon heat treatment conditions and the maximum values of the structural parameters were obtained for the samples annealed at T = 175 degrees C. The particle size Z annealed at different temperature was ranged between 8.1-12.8nm, and the values of the distance distribution function P-max(Z) were obtained when Z = 4.0-6.8 nm. Using one dimension electron density correlation function (1D EDCF) method long period (L) and thickness of the lamellar (d(0)) were estimated and were found to increase with the increase of the degree of crystallinity.

The phase inversion and morphology of nylon 1010 polypropylene blends

Noncompatibilized and compatibilized blends of nylon 1010/PP blends having five different viscosity ratios were prepared by melt extrusion. Glycidyl methacrylate-grafted-polypropylene (PP-g-GMA) was used as the compatibilizer to enbance the adhesion between the two polymers and to stabilize the blend morphology. The effect of the viscosity ratio on the morphology of nylon 1010/polypropylene blends was investigated, with primary attention to the phase-inversion behavior and the average particle size of the dispersed phase. The relationship between the mechanical properties and the phase-inversion composition was investigated as well. Investigation of the morphology of the blends by microscopy indicated that the smaller the viscosity ratio (eta(PP)/eta(PA)) the smaller was the polypropylene concentration at which the phase inversion took place and polypropylene became the continuous phase. The compatibilizer induced a sharp reduction of particle size, but did not have a major effect on the phase-inversion point. An improvement :in the mechanical properties was found when nylon 1010 provided the matrix phase. (C) 1996 John Wiley & Sons, Inc.

APPLICATION OF THE MOMENT METHODS TO ANALYSIS OF X-RAY-DIFFRACTION LINE-PROFILE FOR PA1010-BMI SYSTEM

Pure X-ray diffraction profiles have been analysed for polyamide 1010 and PA1O1O-BMI system by means of multipeak fitting resolution of X-ray diffraction. The methods of variance and fourth moment have been applied to determine the particle size and strain values for the paracrystalline materials. The results indicated that both variance and fourth moment of X-ray diffraction line profile yielded approximately the same values of the particle size and the strain. The particle sizes of (100) reflection have been found to decrease with increasing BMI content, whereas the strain values increased.

MORPHOLOGY AND DYNAMIC-MECHANICAL PROPERTIES OF NYLON 66/POLY(ETHER IMIDE) BLENDS

The morphology and dynamic mechanical properties of blends of poly(ether imide) (PEI) and nylon 66 over the full composition range have been investigated. Torque changes during mixing were also measured. Lower torque values than those calculated by the log-additivity rule were obtained, resulting from the slip at the interface due to low interaction between the components. The particle size of the dispersed phase and morphology of the blends were examined by scanning electron microscopy. The composition of each phase was calculated. The blends of PEI and nylon 66 showed phase-separated structures with small spherical domains of 0.3 similar to 0.7 mu m. The glass transition temperatures (T(g)s) of the blends were shifted inward, compared with those of the homopolymers, which implied that the blends were partially miscible over a range of compositions. T-g1, corresponding to PEI-rich phase, was less affected by composition than T-g2, corresponding to nylon 66-rich phase. This indicated that the fraction of PEI mixed into nylon 66-rich phase increased with decreasing PEI content and that nylon 66 was rarely mixed into the PEI-rich phase. The effect of composition on the secondary relaxations was examined. Both T-beta, corresponding to the motion of amide groups in nylon 66, and T-gamma, corresponding to that of ether groups in PEI, were shifted to higher temperature, probably because of the formation of intermolecular interactions between the components.

SYNTHESIS AND PROPERTIES OF LAFEO3 ULTRAFINE POWDERS

The ultrafine LaFeO3 with particle size of 12 similar to 75nm was prepared by sol-gel method. In the process of gel to ultrafine powder, the weight loss reached 90%. The lowest forming temperature of single phase crystalline LaFeO3 ultrafine powder was ob

Spatial variation of suspended particulate matter in the Yellow Sea

A joint oceanographic cruise between the Institute of Oceanography, Chinese Academy of Science and the Department of Oceanography, Seoul National University was carried out in the Yellow Sea during the summer of 1996 to investigate the concentration and particle-size distribution of suspended particulate matter (SPM). The general trends in the surface and bottom waters show that SPM concentrations and particle sizes decreased seawards in both the western (Chinese) and eastern (Korean) coastal regions of the Yellow Sea. In the bottom waters, SPM concentrations were higher and particle sizes were larger along the eastern coast than along the western coast. We suggest this is due to the resuspension of bottom sediments by strong onshore summer typhoons in the southwestern coastal waters of Korea.

Resuspension and advection processes affecting suspended particulate matter concentrations in the central English Channel

Suspended particulate matter (SPM) measurements obtained along a cross-section in the central English Channel (Wight-Cotentin transect) indicate that the area may be differentiated into: (1) an English coastal zone, associated with the highest concentrations; (2) a French coastal zone, with intermediate concentrations; and (3) the offshore waters of the Channel, characterised by a very low suspended-sediment load. The SPM particle-size distribution was modal close to the English coast (main mode 10-12 mu m); the remainder of the area was characterised by flat SPM distributions. Examination of the diatom communities in the SPM suggest:; that material resuspended in the intertidal zone and the estuarine environments was advected towards the offshore waters of the English Channel. Considerable variations in SPM concentrations occurred during a tidal cycle: maximum concentrations were sometimes up to 3 times higher than the minimum concentrations, Empirical orthogonal function (EOF) analysis of the SPM concentration time series indicates that, although the bottom waters were more turbid than the surficial waters, this was not likely to be the result of in situ sediment resuspension. Instead, the observed variations appear to be controlled mainly by advective mechanisms. The limited resuspension was probably caused by: (1) the limited availability of fine-grained material within the bottom sediments, and (2) 'bed-armouring' processes which protect the finer-grained fractions of the seabed material from erosion and entrainment within the overlying flow during the less energetic stages of the tide.

A preliminary study on fingerprinting approach in marine sediment dynamics with the rare earth elements

Locating the quantitized natural sediment fingerprints is an important work for marine sediment dynamics study. The total of 146 sediment samples were collected from the Shelf of the East China Sea and five rivers, including Huanghe (Yellow), Changjiang (Yangtze), Qiantang, Ou and Min River. The sediment grain size and the contents of rare earth elements (REEs) were measured with laser particle size analyzer and ICP-MS technology. The results show that absolute REE content (Sigma REE) and the concentration ratio of light REEs to heavy REEs (L/HREE) are different in the sediments among those rivers. There are higher REE contents in being less than 2 m and 2-31 mu m fractions in the Changjiang Estuary surface sediments. The REE contents of bulk sediment are dominated by the corresponding values of those leading size-fractions. Sigma REE of sediment is higher close to the estuaries and declines seaward on the inner shelf of the East China Sea (ECS). The L/HREE ratio has a tendency of increase southward from 28 degrees N. Hydrodynamic conditions plays a predominate role on spacial distributions of the surficial sediment's REE parameters. In some situations, the currents tend to remove the coarser light grains from initial populations, as well as the deposit of the finer heavy mineral grains. In other situations, the currents will change the ratio of sediment constituents, such as ratio between silts and clays in the sediments. As a result, the various values of Sigma REE or L/HREE ratio in different bulk sediments are more affected by the change of size-fractions than source location. Under the long-term stable hydrodynamic environment, i.e., the East China Sea Shelf, new sediment transport model based on the size and density gradation concept may help to understand the spatial distribution patterns of REE parameters.

Estimation of suspended sediment concentrations using Pulse-coherent Acoustic Doppler Profiler (PCADP)

The objective of the study is to investigate the suitability of using Pulse-coherent Acoustic Doppler Profiler (PCADP) to estimate suspended sediment concentration (SSC). The acoustic backscatter intensity was corrected for spreading and absorption loss, then calibrated with OBS and finally converted to SSC. The results show that there is a good correlation between SSC and backscatter intensity with R value of 0.74. The mean relative error is 22.4%. Then the time span of little particle size variation was also analyzed to exclude the influence of size variation. The correlation coefficient increased to 0.81 and the error decreased to 18.9%. Our results suggest that the PCADP can meet the requirement of other professional instruments to estimate SSC with the errors between 20% and 50%, and can satisfy the need of dynamics study of suspended particles.

Effects of diet, stocking density, and environmental factors on growth, survival, and metamorphosis of Manila clam Ruditapes philippinarum larvae

A series of experiments was conducted to evaluate the effects of diet, stocking density, and environmental factors on growth, survival, and metamorphosis of Manila clam Ruditapes philippinarum larvae. These experiments examined the following factors: diet (Isochrysts spp., Chlorella spp., and a mixture of Isochrysis spp. and Chlorella spp. [ 1: 1 w/w]), stocking density (5, 10, 15, and 20 larvae ml(-1)), light intensity (un-shaded, partially shaded, and fully shaded), water filtration (unfiltered and sand-filtered), water exchange (50% and 100% once every other day, 25%, 50%, and 100% once daily; 50% and 100% twice daily), and the use of substrate (with and without sand as the substrate). Results indicated that Chlorella spp. could replace 50% of Isochrysis spp. as a food source for the Manila clam larvae without affecting growth, survival, and metamorphosis. Larval growth decreased significantly with increasing stocking density. A density of 5-10 larvae ml(-1) appeared to be optimal for normal growth of Manila clam larvae. Neither diet nor stocking density used in the study had a significant effect on larval survival. Under partially shaded (light intensity = 1000-5000 lx) and fully shaded (light intensity <500 lx) conditions, larval growth was significantly faster than under direct sunlight (un-shaded). A water exchange rate of 50% twice daily provided optimum larval growth. Larvae grew significantly faster in the unfiltered water than in the sand-filtered water. Using sand as the substrate in the culture system significantly depressed the metamorphosis rate. The type and particle size of sand used as the substrate did not significantly affect growth and metamorphosis rates of the larvae. (C) 2005 Published by Elsevier B.V.

Low-temperature molten salt synthesis and characterization of CoWO4 nano-particles

CoWO4 nano-particles were successfully synthesized at a low temperature of 270 degrees C by a molten salt method, and effects of such processing parameters as holding time and salt quantity on the crystallization and development Of CoWO4 crystallites were initially studied. The products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM). and photoluminescent spectra techniques (PL), respectively. Experimental results showed that the well-crystallized CoWO4 nano-particles with ca. 45 nm in diameter could be obtained at 270 degrees C for a holding time of 8 h with 6:1 mass ratio of the salt to CoWO4 precursor, and XRD analysis evidenced that the as-prepared sample was a pure monoclinic phase Of CoWO4 with wolframite structure. Their PL spectra revealed that the CoWO4 nano-particles displayed a very strong PL peak at 453 nm with the excitation wavelength of 230 nm, and PL properties of CoWO4 crystallites relied on their crystalline state, especially on their particle size. (C) 2009 Elsevier B.V. All rights reserved.

Extraction of Nitraria tangutorum seed oil by supercritical carbon dioxide and determination of free fatty acids by HPLC/APC/IMS with fluorescence detection

The seed oil from Nitraria tangutorum samples was obtained by supercritical carbon dioxide extraction methods. The extraction parameters for this methodology, including pressure, temperature, particle size and extraction time, were optimized. The free fatty acids in the seed oil were separated with a pre-column derivation method and 1,2-benzo-3,4-dihydrocarbazole-9-ethyl-p-toluenesulfonate (BDETS) as a labeling regent, followed by high-performance liquid chromatography (HPLC) with fluorescence detection. The target compounds were identified by mass spectrometry with atmospheric pressure chemical ionization (APCI in positive-ion mode). HPLC analysis shows that the main compositions of the seed oil samples were free fatty acids (FFAs) in high to low concentrations as follows: linoleic acid, oleic acid, hexadecanoic acid and octadecanoic acid. The assay detection limits (at signal-to-noise of 3:1) were 3.378-6.572 nmol/L. Excellent linear responses were observed, with correlation coefficients greater than 0.999. The facile BDETS derivatization coupled with mass spectrometry detection allowed the development of a highly sensitive method for analyzing free fatty acids in seed oil by supercritical CO2 extraction. The established method is highly efficient for seed oil extraction and extremely sensitive for fatty acid profile determination. (C) 2007 Elsevier B.V. All rights reserved.

陕北桥镇油田延长组长2、长1油层组沉积相及储层研究

The Ordos Basin is a large-scale craton superimposed basin locating on the west of the North China platform, which was the hotspot of interior basin exploration and development. Qiaozhen oil field located in the Ganquan region of south-central of Ordos Basin. The paper is based on the existing research data, combined with the new theory and progress of the sedimentology, sequence stratigraphy, reservoir sedimentology, petroleum geology, etc, and analyzes systematically the sedimentary and reservoir characteristics in the chang2 and chang1 oil-bearing strata group of Yanchang formation On the basis of stratigraphic classification and comparison study, the strata chang2 and chang1 were divided into five intervals. Appling the method of cartography with single factor and dominance aspect, we have drawn contour line map of sand thickness, contour line map of ratio between sand thickness and stratum thickness. We discussed distribution characteristics of reservoir sand body and evolution of sedimentary facies and microfacies. And combining the field type section , lithologic characteristics, sedimentary structures, the sedimentary facies of single oil well and particle size analysis and according to the features of different sequence, the study area was divided into one sedimentary facies、three parfacies and ten microfacies. The author chew over the characteristics of every facies, parfacies and microfacies and spatial and temporal distribution. Comprehensive research on petrologic characteristics of reservoir , diagenesis types, pore types, distribution of sand bodies, physical properties, oiliness, reservoir heterogeneities, characteristics of interlayer, eventually research on synthetic classifying evaluation of reservoir.The reservoir is classified four types: Ⅰ、Ⅱ、Ⅲ、Ⅳ and pore type, fracture-porosity type. Take reservoir's average thickness, porosity, permeability, oil saturation and shale content as parameters, by using clustering analysis and discriminant analysis, the reservoir is classified three groups. Based on the evaluation, synthetizing the reservoir quality, the sealing ability of cap rock, trap types, reservoir-forming model ,in order to analyze the disciplinarian of accumulation oil&gas. Ultimately, many favorable zones were examined for chang23，chang223，chang222，chang221，chang212，chang12，chang11 intervals. There are twenty two favorable zones in the research area. Meanwhile deploy the next disposition scheme.

白水剖面黄土-红粘土化学风化的粒度效应

The loess-red clay deposit in the Loess Plateau, as large regions mixed in the dust depositional areas, may recorded the chemical weathering features and recycling of the detritus material of the earth’s surface from the wide range upwind of the Loess Plateau. And the loess-red clay sequence is rare information for recovering the continent's weathering history of Late Cenozoic, as it’s clear sense of age. The concentrations of elements in loess-red clay are largely affected by grain size. Therefore, we divided samples of a long loess-red clay section and six spacial sections into three fractions in order to counteracting the effect of particle size on the values of weathering proxies. First, the loess unit L1 and S1 of six sections located at Guyuan, Baishui, Changwu, Yongshou, Yangling and Lantian, Chinese Loess Plateau were sampled. These samples were divided into three fractions: <5μm, 5-20μm, 20-63μm, which were then analyzed for the primary elements using an X-ray fluorescence analyser. Results show that the effect of particle is much smaller on the fraction <5μm than other fractions. Therefore, the fraction <5μm can reflect the change of chemical weathering intensity much better. In addition, we divided Baishui section samples into three fractions, and analyzed them with X-ray fluorescence for primary elements. Results show that the value of CIA vary in different size fractions, indicating different weathering progress. Elements K, Na, Ca and Mg in the <5μm fraction have a sequence which is the reverse of Bowen Sequence. This may be a important sense for the change of source regions.

浑善达克沙地全新世气候变化与风沙活动—夏日淖湖泊沉积记录

Atmospheric dust as an important factor for climate feedbacks is mainly derived from and drove by the aeolian activities of the semi-arid regions in Asia. Therefore, reconstructing the history of aeolian activities in this region has a great significance in understanding the dynamics of past and future climate changes. This paper made a systematical sedimentology, geochemisty and high-resolution chronology analysis on the sediments from the Xiarinao Lake, which located in Hunshandake Desert, Inner Mongolia, and compared with the meteorological records for identifying the indicator of aeolian activities and climate changes. Based on above work, the evolution history of the aeolian activities and climate changes since 11,000 a BP was reconstructed and the dynamics of the aeolian activities and climate changes in the Hunshandake Desert was discussed. The indicator of aeolian activities was established through the comparison of the clastic and chemical records with the meteorological registers in recent 50 years: 1. The sediments of Xiarinao Lake are mainly derived from eaolian clastic materials and composed of two major components: one is the sand fraction (<4 ) similar to the composition of sand dunes, the other is the silt fraction (>4 ) similar to the atmospheric dust. The sand content and the median grain size, particularly the sand content, show a close association with the intensity of wind, indicating that the particle-size composition of the sediments reflect the variations of the aeolian activities. 2. The proportion of soluble salts relative to the total carbonates in the sediments was correlated to the arid degree registered in meteorological records, suggesting that arid degree might be associated with changes of wind speed and the relative proportion of soluble salts to the total carbonate could be used as the indicator of aridity. 3. The δ18O of authigenic calcite in the Xiarinao Lake show a well correlation with both the atmosphere precipitation and variation of the moisture indicated by the concentrations of soluble salts, suggesting that δ18O of anthigenic calcite is a reliable indicator of humidity. Based on above studies, the evolution history of the aeolian activities and climate changes since 11,000 a BP was reconstructed. At the same time, their association and underlying dynamics was discussed: 1. The evolution history of the eaolian activity was reconstructed by the sand content and median grain size. The result showed that aeolian activities had experienced several different climate periods in the Holocene: the aeolian activities fluctuated with a 500-year cycles during the interval from 10,900 to 8200 a BP; no significant aeolian activities had been developed from 8200 to 6300 a BP; during the interval of 6300 to 2600 a BP, sand content and media grain size had increased gradually, the sand content increased from about 5% to 25%, indicating the intensity of aeolian activity increased in the Hunshandake Desert; since 2600 a BP, intensity of aeolian activity has become stronger and activated the sand dunes. 2. The relative arid degree indicated by the proportion of soluble salts relative to the total carbonate show that both the wind speed and dry degree had being increased since 11,000 a BP. During the interval of 10900 to 6300 a BP, no detectable soluble salt was found in the sediments, indicating the humidity condition; the proportion increased to 20% from 6300 to 4200 a BP, showing the climate became drier; the little change of proportion (20%) suggest that the climate was relative stable during the interval of 4200 to 2600 a BP; after 2600 a BP, the proportion increased, showing the climate became further dry. 3. The δ18O evolution of the lake water was established through analysis of authigenetic calcite δ18O for revealing the variations of relative effective humidity in the Hunshandake Desert. δ18O maintained around -6 ‰ during the interval of 10900 to 8200 a BP, showing the climate was a little dry relative to that of the whole Holocnene; in the period of 8200 to 6300 a BP, δ18O had the most negative values, indicating that it was the most humid interval in Holocene; from 6300 to 4200 a BP, δ18O increased from about -7.5 ‰ to about -3 ‰ gradually, suggesting increased aridity; since 4200 a BP, the climate has become stable and dry. On the whole, the records in this study show that the variation of the relative humidity and aridity is consistent with that of summer monsoon in the Hunshandake Desert. The relationships among the grain size, soluble salts relative content, and the authigenic calcite δ18O indicate aeolian activities is controlled by the aridity in the studied area, and the increased aeolian activities is closely associated with the temperature changes under the relative dry condition. The high wind speed under the low temperature leads to the increased aeolian activity, and the temperature change associated with the aeolian activities might be related with the perturbations of the Siberian High Pressure.