Microstructure, mechanical properties and chemical degradation of brazed AISI 316 stainless steel/alumina systems

The main aims of the present study are simultaneously to relate the brazing parameters with: (i) the correspondent interfacial microstructure, (ii) the resultant mechanical properties and (iii) the electrochemical degradation behaviour of AISI 316 stainless steel/alumina brazed joints. Filler metals on such as Ag–26.5Cu–3Ti and Ag–34.5Cu–1.5Ti were used to produce the joints. Three different brazing temperatures (850, 900 and 950 °C), keeping a constant holding time of 20 min, were tested. The objective was to understand the influence of the brazing temperature on the final microstructure and properties of the joints. The mechanical properties of the metal/ceramic (M/C) joints were assessed from bond strength tests carried out using a shear solicitation loading scheme. The fracture surfaces were studied both morphologically and structurally using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction analysis (XRD). The degradation behaviour of the M/C joints was assessed by means of electrochemical techniques. It was found that using a Ag–26.5Cu–3Ti brazing alloy and a brazing temperature of 850 °C, produces the best results in terms of bond strength, 234 ± 18 MPa. The mechanical properties obtained could be explained on the basis of the different compounds identified on the fracture surfaces by XRD. On the other hand, the use of the Ag–34.5Cu–1.5Ti brazing alloy and a brazing temperature of 850 °C produces the best results in terms of corrosion rates (lower corrosion current density), 0.76 ± 0.21 μA cm−2. Nevertheless, the joints produced at 850 °C using a Ag–26.5Cu–3Ti brazing alloy present the best compromise between mechanical properties and degradation behaviour, 234 ± 18 MPa and 1.26 ± 0.58 μA cm−2, respectively. The role of Ti diffusion is fundamental in terms of the final value achieved for the M/C bond strength. On the contrary, the Ag and Cu distribution along the brazed interface seem to play the most relevant role in the metal/ceramic joints electrochemical performance.

Role of abrasive material on micro-abrasion wear tests

Micro-abrasion wear tests with ball-cratering configuration are widely used. Sources of variability are already studied by different authors and conditions for testing are parameterized by BS EN 1071-6: 2007 standard which refers silicon carbide as abrasive. However, the use of other abrasives is possible and allowed. In this work, ball-cratering wear tests were performed using four different abrasive particles of three dissimilar materials: diamond, alumina and silicon carbide. Tests were carried out under the same conditions on a steel plate provided with TiB2 hard coating. For each abrasive, five different test durations were used allowing understanding the initial wear phenomena. Composition and shape of abrasive particles were investigated by SEM and EDS. Scar areas were observed by optical and electronic microscopy in order to understand the wear effects caused by each of them. Scar geometry and grooves were analyzed and compared. Wear coefficient was calculated for each situation. It was observed that diamond particles produce well-defined and circular wear scars. Different silicon carbide particles presented dissimilar results as consequence of distinct particle shape and size distribution.

Influence of the abrasive particles size in the micro-abrasion wear tests of TiAlSiN thin coatings

Ball rotating micro-abrasion tribometers are commonly used to carry out wear tests on thin hard coatings. In these tests, different kinds of abrasives were used, as alumina (Al2O3), silicon carbide (SiC) or diamond. In each kind of abrasive, several particle sizes can be used. Some studies were developed in order to evaluate the influence of the abrasive particle shape in the micro-abrasion process. Nevertheless, the particle size was not well correlated with the material removed amount and wear mechanisms. In this work, slurry of SiC abrasive in distilled water was used, with three different particles size. Initial surface topography was accessed by atomic force microscopy (AFM). Coating hardness measurements were performed with a micro-hardness tester. In order to evaluate the wear behaviour, a TiAlSiN thin hard film was used. The micro-abrasion tests were carried out with some different durations. The abrasive effect of the SiC particles was observed by scanning electron microscopy (SEM) both in the films (hard material) as in the substrate (soft material), after coating perforation. Wear grooves and removed material rate were compared and discussed.

ALSMon: sistema para monitorizar ALS

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Informática e de Computadores

Testes de endurance do tronco: diferenças entre indivíduos com e sem dor lombo-pélvica e o efeito de programas de exercício de controlo motor

Introdução: em indivíduos com dor lombo-pélvica (LPP), parece existir uma alteração de controlo motor e diminuição da endurance dos músculos do tronco. A realização de exercícios de controlo motor pode melhorar a endurance dessa musculatura e consequentemente o controlo motor. Objetivos: detetar diferenças nos tempos e rácios de endurance dos músculos do tronco em indivíduos com e sem dor lombo-pélvica e avaliar o efeito de dois programas de exercícios de controlo motor (segundo Richardson e segundo McGill) nos mesmos outcomes em indivíduos com LPP. Métodos: estudo transversal com uma amostra de 111 indivíduos, 52 para o grupo sem dor (NLPP) e 59 para o com LPP e estudo experimental, constituído pelos indivíduos LPP (59), alocados nos grupos de Pilates (20), McGill (20) ou no grupo controlo (19). Avaliaramse os tempos obtidos nos testes de endurance para os músculos extensores, flexores, flexores laterais direitos e esquerdos do tronco e respetivos rácios, tendo em conta o modelo de McGill. As avaliações dos grupos do estudo experimental realizaram-se antes e após as 8 semanas de exercício. Resultados: os indivíduos com LPP apresentaram tempos e rácios de endurance significativamente inferiores aos indivíduos NLPP (p<0.001). Após as 8 semanas de exercício, registaram-se diferenças estatisticamente significativas entre os grupos em todos os testes de endurance, sendo que o grupo de McGill apresentou tempos significativamente superiores aos do grupo de Pilates para os músculos flexores (p=0.001), flexores laterais direitos (p=0.002) e esquerdos (p=0.009). Quanto aos rácios de endurance, não se detetaram apenas diferenças estatisticamente significativas no rácio flexão lateral esquerda/extensão. Conclusão: os indivíduos com LPP apresentaram tempos e rácios de endurance do tronco inferiores aos dos indivíduos sem dor. Ambos os programas de exercícios melhoraram os tempos e os rácios de endurance, tendo existido uma tendência para melhores resultados na abordagem segundo McGill

A modalidade de financiamento das empresas nas províncias de Kwanza-Norte e Malanje: Angola

Dissertação de Mestrado Apresentado ao Instituto de Contabilidade e Administração do Porto para a obtenção do grau de Mestre em Contabilidade e Finanças, sob orientação do Mestre Adalmiro Álvaro Malheiro de Castro Andrade Pereira.

Low-cost vibration sensors: tendencies and applications in condition monitoring of machines and structures

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Semi-destructive in situ tests as support to the assessment of a conservation process

This paper refers to the assessment on site by semi-destructive testing (SDT) methods of the consolidation efficiency of a conservation process developed by Henriques (2011) for structural and non-structural pine wood elements in service. This study was applied on scots pine wood (Pinus sylvestris L.) degraded by fungi after treatment with a biocidal product followed by consolidation with a polymeric product. This solution avoids substitutions of wood moderately degraded by fungi, improving its physical and mechanical characteristics. The consolidation efficiency was assessed on site by methods of drill resistance and penetration resistance. The SDT methods used showed good sensitivity to the conservation process and could evaluate their effectiveness. (C) 2015 Elsevier Ltd. All rights reserved.

Efficient schedulability tests for real-time embedded systems with urgent routines

Task scheduling is one of the key mechanisms to ensure timeliness in embedded real-time systems. Such systems have often the need to execute not only application tasks but also some urgent routines (e.g. error-detection actions, consistency checkers, interrupt handlers) with minimum latency. Although fixed-priority schedulers such as Rate-Monotonic (RM) are in line with this need, they usually make a low processor utilization available to the system. Moreover, this availability usually decreases with the number of considered tasks. If dynamic-priority schedulers such as Earliest Deadline First (EDF) are applied instead, high system utilization can be guaranteed but the minimum latency for executing urgent routines may not be ensured. In this paper we describe a scheduling model according to which urgent routines are executed at the highest priority level and all other system tasks are scheduled by EDF. We show that the guaranteed processor utilization for the assumed scheduling model is at least as high as the one provided by RM for two tasks, namely 2(2√−1). Seven polynomial time tests for checking the system timeliness are derived and proved correct. The proposed tests are compared against each other and to an exact but exponential running time test.

Analysis of the Respiratory Dynamics During Normal Breathing by Means of Pseudophase Plots and Pressure–Volume Loops

This paper reports on the analysis of tidal breathing patterns measured during noninvasive forced oscillation lung function tests in six individual groups. The three adult groups were healthy, with prediagnosed chronic obstructive pulmonary disease, and with prediagnosed kyphoscoliosis, respectively. The three children groups were healthy, with prediagnosed asthma, and with prediagnosed cystic fibrosis, respectively. The analysis is applied to the pressure-volume curves and the pseudophase-plane loop by means of the box-counting method, which gives a measure of the area within each loop. The objective was to verify if there exists a link between the area of the loops, power-law patterns, and alterations in the respiratory structure with disease. We obtained statistically significant variations between the data sets corresponding to the six groups of patients, showing also the existence of power-law patterns. Our findings support the idea that the respiratory system changes with disease in terms of airway geometry and tissue parameters, leading, in turn, to variations in the fractal dimension of the respiratory tree and its dynamics.

Desenvolvimento de métodos de análise físico-química em águas usando um analisador multiparamétrico AQUAKEM

Trabalho Final de mestrado para obtenção do grau de Mestre em Engenharia Química e Biológica

Syngas production by water electrolysis: preliminary tests on methane production

Master Thesis to obtain the Master degree in Chemical Engineering - Branch Chemical Processes

Utilização de técnicas de análise fotogramétricas em quebra-mares de taludes

Dissertação de Natureza Científica elaborada no Laboratório Nacional de Engenharia Civil (LNEC) para obtenção do grau de mestre em Engenharia Civil na Área de Especialização de Hidráulica no âmbito do protocolo de cooperação entre o ISEL e o LNEC

Avaliação da Perceção dos diferentes Graus de Maitland, na Região Lombar, entre Estudantes e Fisioterapeutas

Introdução – A perceção dos alunos acerca dos diferentes graus de Maitland quando estão a aprender a mobilizar a coluna vertebral não são conhecidas, no entanto esta informação ajudaria no desenvolvimento de estratégias de ensino/aprendizagem para que a sua aplicação seja segura e eficaz. Objetivo - Comparar a perceção dos diferentes graus na realização do movimento postero-anterior central, entre alunos e fisioterapeutas e alunos entre si. Métodos – No presente estudo observacional, analítico transversal, participaram 29 estudantes, divididos em três subgrupos, GA2 (n= 8); GA3 (n = 10) e GA4 (n = 11) e 12 fisioterapeutas. Todos os participantes realizaram num indivíduo assintomático, 5 oscilações, de cada grau, no segmento de L3. Para a recolha dos dados foi utilizado o sistema BioPlux research e para a sua análise o Software Acqknowledge, versão 3,9. O teste de Man-Whitney foi utilizado para determinar as diferenças entre alunos e fisioterapeutas na força, ritmo e amplitude dos 4 graus, e o teste Kruskal Wallis, para comparar os alunos dos diferentes anos, seguido dos testes Post Hoc de Dunn para analisar as variáveis amplitude e força entre os subgrupos. Resultados – Apenas se verificaram diferenças estatísticas entre os alunos e fisioterapeutas no que diz respeito à força na realização do grau IV (p=0,045) e entre os grupos GA2 e GA4 quanto à amplitude executada no grau I (p=0.018) e II (p=0.037) e na força aplicada no grau I (p=0.02) e III (p=0.031), nos quais os alunos do 2º ano realizaram menor amplitude e força que os do 4º ano. Conclusão -Verificaram-se diferenças na perceção da força no grau IV entre alunos e fisioterapeutas. Os alunos do 2º e 4º anos diferem entre si nos graus I e II quanto à amplitude e nos graus I e III quanto à força.

A influência da dor no joelho na incapacidade e proprioceção em adultos mais velhos

Introdução: A dor no joelho apresenta uma etiologia multifatorial, sendo a idade um fator de risco importante. A dor no joelho poderá estar relacionada com alterações na propriocetividade do joelho. Objetivo (s): Comparar a influência dor unilateral com bilateral do joelho na incapacidade e proprioceção em adultos mais velhos. Métodos: Estudo transversal com uma amostra de 11 indivíduos com dor no joelho, divididos em grupo com dor unilateral (GDU=6) e grupo com dor bilateral (GDB=5). Utilizou-se, a Knee injury and Osteoarthritis Outcome Score (KOOS) para analisar a dor, rigidez e outros sintomas, atividades de vida diária, desportivas e de lazer e qualidade de vida. Foi medida a sensação de posição articular passiva e ativa, bem como a sensação de discriminação de carga. Foram utilizados os testes de Mann-Whitney e de correlação de Spearman, com um nível de significância de 0,05. Resultados: Nas diferentes dimensões da KOOS apesar de não se ter verificado diferenças significativas entre os grupos, o GDU apresenta scores menores, que traduzem uma maior incapacidade. Na sensação de posição articular e na sensação de discriminação de carga não se verificaram diferenças significativas entre os grupos. Conclusão: A dor no joelho ser unilateral ou bilateral não influencia nem a incapacidade nem a proprioceção nos adultos mais velhos.