The flammability of metallic materials in normal and reduced gravity

Metallic materials exposed to oxygen-enriched atmospheres – as commonly used in the medical, aerospace, aviation and numerous chemical processing industries – represent a significant fire hazard which must be addressed during design, maintenance and operation. Hence, accurate knowledge of metallic materials flammability is required. Reduced gravity (i.e. space-based) operations present additional unique concerns, where the absence of gravity must also be taken into account. The flammability of metallic materials has historically been quantified using three standardised test methods developed by NASA, ASTM and ISO. These tests typically involve the forceful (promoted) ignition of a test sample (typically a 3.2 mm diameter cylindrical rod) in pressurised oxygen. A test sample is defined as flammable when it undergoes burning that is independent of the ignition process utilised. In the standardised tests, this is indicated by the propagation of burning further than a defined amount, or „burn criterion.. The burn criterion in use at the onset of this project was arbitrarily selected, and did not accurately reflect the length a sample must burn in order to be burning independent of the ignition event and, in some cases, required complete consumption of the test sample for a metallic material to be considered flammable. It has been demonstrated that a) a metallic material.s propensity to support burning is altered by any increase in test sample temperature greater than ~250-300 oC and b) promoted ignition causes an increase in temperature of the test sample in the region closest to the igniter, a region referred to as the Heat Affected Zone (HAZ). If a test sample continues to burn past the HAZ (where the HAZ is defined as the region of the test sample above the igniter that undergoes an increase in temperature of greater than or equal to 250 oC by the end of the ignition event), it is burning independent of the igniter, and should be considered flammable. The extent of the HAZ, therefore, can be used to justify the selection of the burn criterion. A two dimensional mathematical model was developed in order to predict the extent of the HAZ created in a standard test sample by a typical igniter. The model was validated against previous theoretical and experimental work performed in collaboration with NASA, and then used to predict the extent of the HAZ for different metallic materials in several configurations. The extent of HAZ predicted varied significantly, ranging from ~2-27 mm depending on the test sample thermal properties and test conditions (i.e. pressure). The magnitude of the HAZ was found to increase with increasing thermal diffusivity, and decreasing pressure (due to slower ignition times). Based upon the findings of this work, a new burn criterion requiring 30 mm of the test sample to be consumed (from the top of the ignition promoter) was recommended and validated. This new burn criterion was subsequently included in the latest revision of the ASTM G124 and NASA 6001B international test standards that are used to evaluate metallic material flammability in oxygen. These revisions also have the added benefit of enabling the conduct of reduced gravity metallic material flammability testing in strict accordance with the ASTM G124 standard, allowing measurement and comparison of the relative flammability (i.e. Lowest Burn Pressure (LBP), Highest No-Burn Pressure (HNBP) and average Regression Rate of the Melting Interface(RRMI)) of metallic materials in normal and reduced gravity, as well as determination of the applicability of normal gravity test results to reduced gravity use environments. This is important, as currently most space-based applications will typically use normal gravity information in order to qualify systems and/or components for reduced gravity use. This is shown here to be non-conservative for metallic materials which are more flammable in reduced gravity. The flammability of two metallic materials, Inconel® 718 and 316 stainless steel (both commonly used to manufacture components for oxygen service in both terrestrial and space-based systems) was evaluated in normal and reduced gravity using the new ASTM G124-10 test standard. This allowed direct comparison of the flammability of the two metallic materials in normal gravity and reduced gravity respectively. The results of this work clearly show, for the first time, that metallic materials are more flammable in reduced gravity than in normal gravity when testing is conducted as described in the ASTM G124-10 test standard. This was shown to be the case in terms of both higher regression rates (i.e. faster consumption of the test sample – fuel), and burning at lower pressures in reduced gravity. Specifically, it was found that the LBP for 3.2 mm diameter Inconel® 718 and 316 stainless steel test samples decreased by 50% from 3.45 MPa (500 psia) in normal gravity to 1.72 MPa (250 psia) in reduced gravity for the Inconel® 718, and 25% from 3.45 MPa (500 psia) in normal gravity to 2.76 MPa (400 psia) in reduced gravity for the 316 stainless steel. The average RRMI increased by factors of 2.2 (27.2 mm/s in 2.24 MPa (325 psia) oxygen in reduced gravity compared to 12.8 mm/s in 4.48 MPa (650 psia) oxygen in normal gravity) for the Inconel® 718 and 1.6 (15.0 mm/s in 2.76 MPa (400 psia) oxygen in reduced gravity compared to 9.5 mm/s in 5.17 MPa (750 psia) oxygen in normal gravity) for the 316 stainless steel. Reasons for the increased flammability of metallic materials in reduced gravity compared to normal gravity are discussed, based upon the observations made during reduced gravity testing and previous work. Finally, the implications (for fire safety and engineering applications) of these results are presented and discussed, in particular, examining methods for mitigating the risk of a fire in reduced gravity.

Towards a controlled growth of self-assembled nanostructures: shaping, ordering and localization in Ge/Si heteroepitaxy.

The strain-induced self-assembly of suitable semiconductor pairs is an attractive natural route to nanofabrication. To bring to fruition their full potential for actual applications, individual nanostructures need to be combined into ordered patterns in which the location of each single unit is coupled with others and the surrounding environment. Within the Ge/Si model system, we analyze a number of examples of bottom-up strategies in which the shape, positioning, and actual growth mode of epitaxial nanostructures are tailored by manipulating the intrinsic physical processes of heteroepitaxy. The possibility of controlling elastic interactions and, hence, the configuration of self-assembled quantum dots by modulating surface orientation with the miscut angle is discussed. We focus on the use of atomic steps and step bunching as natural templates for nanodot clustering. Then, we consider several different patterning techniques which allow one to harness the natural self-organization dynamics of the system, such as: scanning tunneling nanolithography, focused ion beam and nanoindentation patterning. By analyzing the evolution of the dot assembly by scanning probe microscopy, we follow the pathway which leads to lateral ordering, discussing the thermodynamic and kinetic effects involved in selective nucleation on patterned substrates.

Relationship to the bereaved and perceptions of severity of trauma differentiate elements of posttraumatic growth

The field of bereavement and grief has been expanding to recognise the potential for growth following the loss of a loved one. This study sought to examine the effect of the relationship to the deceased and perceptions of the severity of the trauma on dimensions of posttraumatic growth. Participants were 146 people who had lost either: a) a first degree relative, b) a second degree relative, or c) a non-related friend. Results demonstrated that both severity and the relationship to the bereaved differentiate posttraumatic growth outcomes. For example, participants who had lost a first degree relative reported higher levels of growth than those who had lost a second degree relative. Consistent with previous research in general trauma populations, the more severe the loss was rated, the higher the levels of growth. Implications for practice are discussed.

Factors effecting motor vehicle growth in Dhaka

Dhaka’s traffic is heterogeneous, both motorized (MT) and non-motorized (NMT) transport are common. Traffic congestion has become a part of city dwellers’ lives. This paper explores the factors for motor vehicle growth in Dhaka. The scope of the paper will be limited to literature review...

Formation mechanisms of secondary organic aerosols in relation to laser printer emissions

Due to their large surface area, complex chemical composition and high alveolar deposition rate, ultrafine particles (UFPs) (< 0.1 ìm) pose a significant risk to human health and their toxicological effects have been acknowledged by the World Health Organisation. Since people spend most of their time indoors, there is a growing concern about the UFPs present in some indoor environments. Recent studies have shown that office machines, in particular laser printers, are a significant indoor source of UFPs. The majority of printer-generated UFPs are organic carbon and it is unlikely that these particles are emitted directly from the printer or its supplies (such as paper and toner powder). Thus, it was hypothesised that these UFPs are secondary organic aerosols (SOA). Considering the widespread use of printers and human exposure to these particles, understanding the processes involved in particle formation is of critical importance. However, few studies have investigated the nature (e.g. volatility, hygroscopicity, composition, size distribution and mixing state) and formation mechanisms of these particles. In order to address this gap in scientific knowledge, a comprehensive study including state-of-art instrumental methods was conducted to characterise the real-time emissions from modern commercial laser printers, including particles, volatile organic compounds (VOCs) and ozone (O3). The morphology, elemental composition, volatility and hygroscopicity of generated particles were also examined. The large set of experimental results was analysed and interpreted to provide insight into: (1) Emissions profiles of laser printers: The results showed that UFPs dominated the number concentrations of generated particles, with a quasi unimodal size distribution observed for all tests. These particles were volatile, non-hygroscopic and mixed both externally and internally. Particle microanalysis indicated that semi-volatile organic compounds occupied the dominant fraction of these particles, with only trace quantities of particles containing Ca and Fe. Furthermore, almost all laser printers tested in this study emitted measurable concentrations of VOCs and O3. A positive correlation between submicron particles and O3 concentrations, as well as a contrasting negative correlation between submicron particles and total VOC concentrations were observed during printing for all tests. These results proved that UFPs generated from laser printers are mainly SOAs. (2) Sources and precursors of generated particles: In order to identify the possible particle sources, particle formation potentials of both the printer components (e.g. fuser roller and lubricant oil) and supplies (e.g. paper and toner powder) were investigated using furnace tests. The VOCs emitted during the experiments were sampled and identified to provide information about particle precursors. The results suggested that all of the tested materials had the potential to generate particles upon heating. Nine unsaturated VOCs were identified from the emissions produced by paper and toner, which may contribute to the formation of UFPs through oxidation reactions with ozone. (3) Factors influencing the particle emission: The factors influencing particle emissions were also investigated by comparing two popular laser printers, one showing particle emissions three orders of magnitude higher than the other. The effects of toner coverage, printing history, type of paper and toner, and working temperature of the fuser roller on particle number emissions were examined. The results showed that the temperature of the fuser roller was a key factor driving the emission of particles. Based on the results for 30 different types of laser printers, a systematic positive correlation was observed between temperature and particle number emissions for printers that used the same heating technology and had a similar structure and fuser material. It was also found that temperature fluctuations were associated with intense bursts of particles and therefore, they may have impact on the particle emissions. Furthermore, the results indicated that the type of paper and toner powder contributed to particle emissions, while no apparent relationship was observed between toner coverage and levels of submicron particles. (4) Mechanisms of SOA formation, growth and ageing: The overall hypothesis that UFPs are formed by reactions with the VOCs and O3 emitted from laser printers was examined. The results proved this hypothesis and suggested that O3 may also play a role in particle ageing. In addition, knowledge about the mixing state of generated particles was utilised to explore the detailed processes of particle formation for different printing scenarios, including warm-up, normal printing, and printing without toner. The results indicated that polymerisation may have occurred on the surface of the generated particles to produce thermoplastic polymers, which may account for the expandable characteristics of some particles. Furthermore, toner and other particle residues on the idling belt from previous print jobs were a very clear contributing factor in the formation of laser printer-emitted particles. In summary, this study not only improves scientific understanding of the nature of printer-generated particles, but also provides significant insight into the formation and ageing mechanisms of SOAs in the indoor environment. The outcomes will also be beneficial to governments, industry and individuals.

Human neural cell interactions with orientated electrospun nanofibers in vitro

Aim: Electrospun nanofibers represent potent guidance substrates for nervous tissue repair. Development of nanofiber-based scaffolds for CNS repair requires, as a first step, an understanding of appropriate neural cell type-substrate interactions. Materials & methods: Astrocyte–nanofiber interactions (e.g., adhesion, proliferation, process extension and migration) were studied by comparing human neural progenitor-derived astrocytes (hNP-ACs) and a human astrocytoma cell line (U373) with aligned polycaprolactone (PCL) nanofibers or blended (25% type I collagen/75% PCL) nanofibers. Neuron–nanofiber interactions were assessed using a differentiated human neuroblastoma cell line (SH-SY5Y). Results & discussion: U373 cells and hNP-AC showed similar process alignment and length when associated with PCL or Type I collagen/PCL nanofibers. Cell adhesion and migration by hNP-AC were clearly improved by functionalization of nanofiber surfaces with type I collagen. Functionalized nanofibers had no such effect on U373 cells. Another clear difference between the U373 cells and hNP-AC interactions with the nanofiber substrate was proliferation; the cell line demonstrating strong proliferation, whereas the hNP-AC line showed no proliferation on either type of nanofiber. Long axonal growth (up to 600 µm in length) of SH-SY5Y neurons followed the orientation of both types of nanofibers even though adhesion of the processes to the fibers was poor. Conclusion: The use of cell lines is of only limited predictive value when studying cell–substrate interactions but both morphology and alignment of human astrocytes were affected profoundly by nanofibers. Nanofiber surface functionalization with collagen significantly improved hNP-AC adhesion and migration. Alternative forms of functionalization may be required for optimal axon–nanofiber interactions.

The growth and international expansion of an emerging market retailer in Latin America

This study contributes to the literature on international retailing by addressing a gap in the literature as to how retailers from emerging markets expand internationally. This historical case study analyzes the growth and internationalization process of Chilean retailer Falabella, one of the largest in Latin America and has been able to compete with multinationals from developed countries. The research is based upon primary and secondary data sources including 33 oral interviews with company managers and family executives, as well as industry data, corporate reports, and trade journals. Drawing on institutional theory, the findings show that by belonging to a family conglomerate, engaging in networks and partnerships, organizational learning, and having an experienced management team helped Falabella gain legitimacy in all international markets.

Learning by design workshop

The Learning by Design Workshop Program 2010, a part of the Queensland Government Unlimited: Designing for the Asia Pacific Event Program, was a one-day professional development design thinking workshop run on October 9, 2011 at The Edge, State Library of Queensland for self-selected public and private secondary school teachers from the subject areas of Visual Art, Graphics and Industrial Technology and Design. Participants were drawn from a database of Brisbane and regional Queensland schools from the goDesign and Living City Workshop Programs. It aimed to generate leadership within schools for design-led education and creative thinking and give teachers a rare opportunity to work with professional designers to generate future strategies for design-based learning. Teachers were introduced to the concept of design thinking in education by international keynote speakers CJ Lim (Studio 8 Architects) and Jeb Brugmann (The Next Practice), national speaker Oliver Freeman (NevilleFreeman Agency) and three Queensland speakers, Alexander Loterztain, David Williams and Keith Holledge. Inspired by the Unlimited showcase exhibition Make Change: Design Thinking in Action and ‘Idea Starters’/teaching resources provided, teachers worked with a professional designer (from a discipline of architecture, interior design, industrial design, urban design, graphic design or landscape architecture) in ten random teams, to generate optimistic ideas for the Ideal City of tomorrow, each considering a theme – Food, Water, Transport, Ageing, Growth, Employment, Shelter, Health, Education and Energy. They then discussed how this process could be best activated and expanded on to build interest and knowledge in design thinking in the classroom. Assisted by illustrators, the teams prepared a visual presentation of their ideas and process from art materials provided. The workshop culminated in a video-taped interactive design charette to the larger group, which is intended to be utilised as a toolkit and praxis for teachers as part of the State Library of Queensland Design Minds Website Project.

Generation workshop 2010

The Generation Workshop Program 2010, a part of the Queensland Government Unlimited: Designing for the Asia Pacific Event Program, consisted of two one-day intensive design thinking workshops run on October 7-8, 2011 at The Edge, State Library of Queensland, for 100 senior secondary students and 20 secondary teachers self-selected from the subject areas of Visual Art, Graphics and Industrial Technology and Design. Participants were drawn from a database of Brisbane and regional Queensland private and public schools from the goDesign and Living City Workshop Programs. The workshop aimed to facilitate awareness in young people of the role of design in society and the value of design thinking skills in solving complex problems facing the Asia Pacific Region, and to inspire the generation of strategies for our future cities. It also aimed to encourage the collaboration of professional designers with secondary schools to inspire post-secondary pathways and idea generation for education. Inspired by international and national speakers Bunker Roy (Barefoot College) and Hael Kobayashi (Associate Producer on "Happy Feet" film for Australia's Animal Logic), the Unlimited showcase exhibition Make Change: Design Thinking in Action and ‘Idea Starters’/teaching resources provided, students worked with a teacher in ten random teams, to generate optimistic strategies for the Ideal City of tomorrow, each considering a theme – Food, Water, Transport, Ageing, Growth, Employment, Shelter, Health, Education and Energy. Each team of 6 was led by a professional designer (from the discipline of architecture, interior design, industrial design, urban design, graphic design or landscape architecture) who was a catalyst for driving the student creative thinking process. Assisted by illustrators, the teams prepared a visual presentation of their idea from art materials provided. The workshop culminated in a video-taped interactive design chatter to the larger group, which will be utilised as a toolkit and praxis for teachers as part of the State Library of Queensland Design Minds Project. Photos of student design work were published on the Unlimited website.

A fibrocontractive mechanochemical model of dermal wound closure incorporating realistic growth factor kinetics

Fibroblasts and their activated phenotype, myofibroblasts, are the primary cell types involved in the contraction associated with dermal wound healing. Recent experimental evidence indicates that the transformation from fibroblasts to myofibroblasts involves two distinct processes: the cells are stimulated to change phenotype by the combined actions of transforming growth factor β (TGFβ) and mechanical tension. This observation indicates a need for a detailed exploration of the effect of the strong interactions between the mechanical changes and growth factors in dermal wound healing. We review the experimental findings in detail and develop a model of dermal wound healing that incorporates these phenomena. Our model includes the interactions between TGFβ and collagenase, providing a more biologically realistic form for the growth factor kinetics than those included in previous mechanochemical descriptions. A comparison is made between the model predictions and experimental data on human dermal wound healing and all the essential features are well matched.

A conceptual model to link deep customer insights to both growth opportunities and organisational strategy in SME’s as part of a design led transformation journey

Although Design Led Innovation activities aim to raise the value of design within the business, knowledge about which tools are available to support companies and how to apply them to make the connection between design for new product development and design as a strategic driver of growth is needed. This paper presents a conceptual method to supplement existing process and tools to assist companies to grow through design. The model extends the authors’ previous work to explore how through storytelling, customer observation can be captured and translated into new meaning, then creating new design propositions shaped into product needs, which can drive internal business activities, brand and the strategic vision. The paper contributes to a gap in the theoretical frameworks and literature by highlighting the need to align and scale design processes which match the needs of SME’s as they transition along a trajectory to become design led businesses.