Conducting gel-fibres based on carrageenan, chitosan and carbon nanotubes

A simple continuous flow wet-spinning method for assembling fibres consisting of two oppositely charged biopolymers (chitosan and carrageenan) and carbon nanotubes is reported. It was observed that the order in which the biopolymers are added, i.e. spinning chitosan into one of the carrageenans (or vice versa), affects the fibre composition as well as the resulting electrical and mechanical properties. The addition of carbon nanotubes into the fibres was found to improve Young's modulus values coupled with a significant improvement in the electrical conductivity by up to 6 orders of magnitude.

Spinning Carbon Nanotube-Gel Fibers Using Polyelectrolyte Complexation

Biopolymer-single walled carbon nanotube (SWNT)-biopolymer fibers were prepared using a continuous flow spinning approach. Polyelectrolyte complexation was facilitated by injecting a SWNT-biopolymer dispersion into a coagulation bath containing a biopolymer of opposite charge. We showed that the ability to spin fibers and their properties depend on processing conditions such as polyelectrolyte pH, sonolysis regime (conditions employed to disperse SWNT) and the order of adding the anionic and cationic biopolymer solutions. Maximizing the ionic nature through changes in the pH increased spin-ability, while combining a sonicated dispersion with an as-prepared (non-sonicated) polyelectrolyte solution allowed us to optimize sonolysis conditions while retaining spin-ability of fibers with smooth surface morphology. Addition of the cationic biopolymer-SWNT dispersion to the anionic biopolymer solution resulted in mechanical reinforcement with the increase in SWNT loading fraction. All fibers decreased their electrical resistance upon exposure to water vapor.

Porous carbon nanotube/polyvinylidene fluoride composite material: Superhydrophobicity/superoleophilicity and tunability of electrical conductivity

Porous carbon nanotube/polyvinylidene fluoride (CNT/PVDF) composite material can be fabricated via formation and freeze-drying of a gel. The field emission scanning electron microscopy, nitrogen adsorption-desorption and pore size distribution analysis reveal that the introduction of a small amount of carbon nanotubes (CNTs) can effectively increase the surface roughness and porosity of polyvinylidene fluoride (PVDF). Contact angle measurements of water and oil indicate that the as-obtained composite material is superhydrophobic and superoleophilic. Further experiments demonstrate that these composite material can be efficiently used to separate/absorb the insoluble oil from oil polluted water as membrane/absorbent. Most importantly, the electrical conductivity of such porous CNT/PVDF composite material can be tuned by adjusting the mass ratio of CNT to PVDF without obviously changing the superhydrophobicity or superoleophilicity. The unique properties of the porous CNT/PVDF composite material make it a promising candidate for oil-polluted water treatment as well as water-repellent catalyst-supporting electrode material.

Excellent electrochemical performance of LiFe0.4Mn0.6PO4 microspheres produced using a double carbon coating process

Composite LiFe0.4Mn0.6PO4/C microspheres are considered advanced cathode materials for electric vehicles and other high-energy density applications due to their advantages of high energy density and excellent cycling stability. LiFe0.4Mn0.6PO4/C microspheres have been produced using a double carbon coating process employing traditional industrial techniques (ball milling, spray-drying and annealing). The obtained LiFe0.4Mn0.6PO4 microspheres exhibit a high discharge capacity of around 166 mA h g-1 at 0.1 C and excellent rate capabilities of 132, 103, and 72 mA h g-1 at 5, 10, and 20 C, respectively. A reversible capacity of about 152 mA h g-1 after 500 cycles at a current density of 1 C indicates an outstanding cycling stability. The excellent electrochemical performance is attributed to the micrometer-sized spheres of double carbon-coated LiFe0.4Mn0.6PO4 nanoparticles with improved electric conductivity and higher Li ion diffusion coefficients, ensuring full redox reactions of all nanoparticles. The results show that the advanced high-energy density cathode materials can be produced using existing industry techniques.

Retention of the original LLC structure in a cross-linked poly(ethylene glycol) diacrylate hydrogel with reinforcement from a silica network

Cross-linked poly(ethylene glycol) diacrylate (PEGDA) hydrogels with uniformly controlled nanoporous structures templated from hexagonal lyotropic liquid crystals (LLC) represent separation membrane materials with potentially high permeability and selectivity due to their high pore density and narrow pore size distribution. However, retaining LLC templated nanostructures is a challenge as the polymer gels are not strong enough to sustain the surface tension during the drying process. In the current study, cross-linked PEGDA gels were reinforced with a silica network synthesized via an in situ sol-gel method, which assists in the retention of the hexagonal LLC structure. The silica precursor does not obstruct the formation of hexagonal phases. After surfactant removal and drying, these hexagonal structures in samples with a certain amount of tetraethoxysilane (TEOS) loading are well retained while the nanostructures are collapsed in samples without silica reinforcement, leading to the hypothesis that the reinforcement provided by the silica network stabilizes the LLC structure. The study examines the conditions necessary for a sufficient and well dispersed silica network in PEGDA gels that contributes to the retention of original LLC structures, which potentially enables broad applications of these gels as biomedical and membrane materials.

Drying and denaturation characteristics of α-lactalbumin, β-lactoglobulin, and bovine serum albumin in a convective drying process

Drying and denaturation kinetics of aqueous droplets of α-lactalbumin (α-lac), β-lactoglobulin (β-lg), and bovine serum albumin (BSA) were measured in a convective drying environment. Single droplets having an initial droplet diameter of 2 ± 0.1 mm and containing 10% (w/v) protein concentration were dried using conditioned air (65 and 80 °C, 2-3% RH, 0.5 m/s velocity) for 600 s. The denaturation of these proteins was measured by using reversed-phase HPLC. At the end of 600 s of drying 13.3 and 19.4% α-lac was found to be lost due to denaturation at 65 and 80 °C, respectively. Up to 31.0% of β-lg was found to be denatured, whereas BSA was not found to be significantly (p > 0.05) denatured in these drying conditions. The formation and strength of skin and the associated morphological features were found to be linked with the degree of denaturation of these proteins. The secondary structure of these proteins was significantly (p < 0.05) affected and altered by the drying stresses. The β-sheet and random coil contents were increased in α-lac by 6.5 and 4.0%, respectively, whereas the α-helix and β-turn contents decreased by 5.5 and 5.0%, respectively. The β-sheet and random coil contents in β-lg were increased by 7.5 and 2.0%, respectively, whereas the α-helix and β-turn contents decreased by 3.5 and 6.0%, respectively. In the case of BSA the β-sheet, α-helix, and random coil contents were found to increase, whereas the β-turn content decreased.

Reduced graphene oxide directed self-assembly of phospholipid monolayers in liquid and gel phases

The response of cell membranes to the local physical environment significantly determines many biological processes and the practical applications of biomaterials. A better understanding of the dynamic assembly and environmental response of lipid membranes can help understand these processes and design novel nanomaterials for biomedical applications. The present work demonstrates the directed assembly of lipid monolayers, in both liquid and gel phases, on the surface of a monolayered reduced graphene oxide (rGO). The results from atomic force microscopy indicate that the hydrophobic aromatic plane and the defect holes due to reduction of GO sheets, along with the phase state and planar surface pressure of lipids, corporately determine the morphology and lateral structure of the assembled lipid monolayers. The DOPC molecules, in liquid phase, probably spread over the rGO surface with their tails associating closely with the hydrophobic aromatic plane, and accumulate to form circles of high area surrounding the defect holes on rGO sheets. However, the DPPC molecules, in gel phase, prefer to form a layer of continuous membrane covering the whole rGO sheet including defect holes. The strong association between rGO sheets and lipid tails further influences the melting behavior of lipids. This work reveals a dramatic effect of the local structure and surface property of rGO sheets on the substrate-directed assembly and subsequent phase behavior of the supported lipid membranes.

Distinct kinetics of molecular gelation in a confined space and its relation to the structure and property of thin gel films

Thin films of molecular gels formed in a confined space have potential applications in transdermal delivery, artificial skin, molecular electronics, etc. The microstructures and properties of thin gel films can be significantly different from those of their bulk counterparts. However, so far a comprehensive understanding of the effects of spatial confinement on the molecular gelation kinetics, fiber network structure and related mechanical properties is still lacking. In this work, using rheological techniques, we investigated the effect of one-dimensional confinement on the formation kinetics of fiber networks in the molecular gelation process. Fractal analyses of the kinetic information in terms of an extended Dickinson model enabled us to describe quantitatively the distinct kinetic signature of molecular gelation. The structural features derived from gelation kinetics support well the fractal patterns of the fiber networks acquired by optical and electron microscopy. With the kinetics-structure correlation, we can gain an in-depth understanding of the confinement-induced differences in the structure and consequently the mechanical properties of a model molecular gelling system. Particularly, the confinement induced structural transition, from a three-dimensional, dense and compact spherulitic network composed of highly branched fibers to a quasi-two-dimensional sparse spherulitic network composed of less branched fibers and entangled fibrils at the boundary areas, renders a gel film to become less stiff but more ductile. Our study suggests here a new strategy of engineering the fiber network microstructure to achieve functional gel films with unusual but useful properties.