Vibration analysis of a printed circuit board

The reliability of the printed circuit board assembly under dynamic environments, such as those found onboard airplanes, ships and land vehicles is receiving more attention. This research analyses the dynamic characteristics of the printed circuit board (PCB) supported by edge retainers and plug-in connectors. By modelling the wedge retainer and connector as providing simply supported boundary condition with appropriate rotational spring stiffnesses along their respective edges with the aid of finite element codes, accurate natural frequencies for the board against experimental natural frequencies are obtained. For a PCB supported by two opposite wedge retainers and a plug-in connector and with its remaining edge free of any restraint, it is found that these real supports behave somewhere between the simply supported and clamped boundary conditions and provide a percentage fixity of 39.5% more than the classical simply supported case. By using an eigensensitivity method, the rotational stiffnesses representing the boundary supports of the PCB can be updated effectively and is capable of representing the dynamics of the PCB accurately. The result shows that the percentage error in the fundamental frequency of the PCB finite element model is substantially reduced from 22.3% to 1.3%. The procedure demonstrated the effectiveness of using only the vibration test frequencies as reference data when the mode shapes of the original untuned model are almost identical to the referenced modes/experimental data. When using only modal frequencies in model improvement, the analysis is very much simplified. Furthermore, the time taken to obtain the experimental data will be substantially reduced as the experimental mode shapes are not required.In addition, this thesis advocates a relatively simple method in determining the support locations for maximising the fundamental frequency of vibrating structures. The technique is simple and does not require any optimisation or sequential search algorithm in the analysis. The key to the procedure is to position the necessary supports at positions so as to eliminate the lower modes from the original configuration. This is accomplished by introducing point supports along the nodal lines of the highest possible mode from the original configuration, so that all the other lower modes are eliminated by the introduction of the new or extra supports to the structure. It also proposes inspecting the average driving point residues along the nodal lines of vibrating plates to find the optimal locations of the supports. Numerical examples are provided to demonstrate its validity. By applying to the PCB supported on its three sides by two wedge retainers and a connector, it is found that a single point constraint that would yield maximum fundamental frequency is located at the mid-point of the nodal line, namely, node 39. This point support has the effect of increasing the structure's fundamental frequency from 68.4 Hz to 146.9 Hz, or 115% higher.

The experimental evaluation of the dynamics of fluid-loaded microplates

An experimental testing system for the study of the dynamic behavior of fluid-loaded rectangular micromachined silicon plates is designed and presented in this paper. In this experimental system, the base-excitation technique combined with pseudo-random signal and cross-correlation analysis is applied to test fluid-loaded microstructures. Theoretical model is also derived to reveal the mechanism of such an experimental system in the application of testing fluid-loaded microstructures. The dynamic experiments cover a series of testings of various microplates with different boundary conditions and dimensions, both in air and immersed in water. This paper is the first that demonstrates the ability and performances of base excitation in the application of dynamic testing of microstructures that involves a natural fluid environment. Traditional modal analysis approaches are used to evaluate natural frequencies, modal damping and mode shapes from the experimental data. The obtained experimental results are discussed and compared with theoretical predictions. This research experimentally determines the dynamic characteristics of the fluid-loaded silicon microplates, which can contribute to the design of plate-based microsystems. The experimental system and testing approaches presented in this paper can be widely applied to the investigation of the dynamics of microstructures and nanostructures.

Vibration analysis of submerged rectangular microplates with distributed mass loading

This paper investigates the vibration characteristics of the coupling system of a microscale fluid-loaded rectangular isotropic plate attached to a uniformly distributed mass. Previous literature has, respectively, studied the changes in the plate vibration induced by an acoustic field or by the attached mass loading. This paper investigates the issue of involving these two types of loading simultaneously. Based on Lamb's assumption of the fluid-loaded structure and the Rayleigh–Ritz energy method, this paper presents an analytical solution for the natural frequencies and mode shapes of the coupling system. Numerical results for microplates with different types of boundary conditions have also been obtained and compared with experimental and numerical results from previous literature. The theoretical model and novel analytical solution are of particular interest in the design of microplate-based biosensing devices.

Proteomic analysis of a noninvasive human model of acute inflammation and its resolution:the twenty-one day gingivitis model

The 21-day experimental gingivitis model, an established noninvasive model of inflammation in response to increasing bacterial accumulation in humans, is designed to enable the study of both the induction and resolution of inflammation. Here, we have analyzed gingival crevicular fluid, an oral fluid comprising a serum transudate and tissue exudates, by LC-MS/MS using Fourier transform ion cyclotron resonance mass spectrometry and iTRAQ isobaric mass tags, to establish meta-proteomic profiles of inflammation-induced changes in proteins in healthy young volunteers. Across the course of experimentally induced gingivitis, we identified 16 bacterial and 186 human proteins. Although abundances of the bacterial proteins identified did not vary temporally, Fusobacterium outer membrane proteins were detected. Fusobacterium species have previously been associated with periodontal health or disease. The human proteins identified spanned a wide range of compartments (both extracellular and intracellular) and functions, including serum proteins, proteins displaying antibacterial properties, and proteins with functions associated with cellular transcription, DNA binding, the cytoskeleton, cell adhesion, and cilia. PolySNAP3 clustering software was used in a multilayered analytical approach. Clusters of proteins that associated with changes to the clinical parameters included neuronal and synapse associated proteins.

Statnote 31:analysis of covariance

Analysis of covariance (ANCOVA) is a useful method of ‘error control’, i.e., it can reduce the size of the error variance in an experimental or observational study. An initial measure obtained before the experiment, which is closely related to the final measurement, is used to adjust the final measurements, thus reducing the error variance. When this method is used to reduce the error term, the X variable must not itself be affected by the experimental treatments, because part of the treatment effect would then also be removed. Hence, the method can only be safely used when X is measured before an experiment. A further limitation of the analysis is that only the linear effect of Y on X is being removed and it is possible that Y could be a curvilinear function of X. A question often raised is whether ANCOVA should be used routinely in experiments rather than a randomized blocks or split-plot design, which may also reduce the error variance. The answer to this question depends on the relative precision of the difference methods with reference to each scenario. Considerable judgment is often required to select the best experimental design and statistical help should be sought at an early stage of an investigation.

Statistical guidelines for the analysis of data obtained from one or both eyes

Purpose - Measurements obtained from the right and left eye of a subject are often correlated whereas many statistical tests assume observations in a sample are independent. Hence, data collected from both eyes cannot be combined without taking this correlation into account. Current practice is reviewed with reference to articles published in three optometry journals, viz., Ophthalmic and Physiological Optics (OPO), Optometry and Vision Science (OVS), Clinical and Experimental Optometry (CEO) during the period 2009–2012. Recent findings - Of the 230 articles reviewed, 148/230 (64%) obtained data from one eye and 82/230 (36%) from both eyes. Of the 148 one-eye articles, the right eye, left eye, a randomly selected eye, the better eye, the worse or diseased eye, or the dominant eye were all used as selection criteria. Of the 82 two-eye articles, the analysis utilized data from: (1) one eye only rejecting data from the adjacent eye, (2) both eyes separately, (3) both eyes taking into account the correlation between eyes, or (4) both eyes using one eye as a treated or diseased eye, the other acting as a control. In a proportion of studies, data were combined from both eyes without correction. Summary - It is suggested that: (1) investigators should consider whether it is advantageous to collect data from both eyes, (2) if one eye is studied and both are eligible, then it should be chosen at random, and (3) two-eye data can be analysed incorporating eyes as a ‘within subjects’ factor.

An analysis of the role of soft systems methodology in the change process and the contribution of the facilitator within this process

This research aims to examine the effectiveness of Soft Systems Methodology (SSM) to enable systemic change within local goverment and local NHS environments and to examine the role of the facilitator within this process. Checkland's Mode 2 variant of Soft Systems Methodology was applied on an experimental basis in two environments, Herefordshire Health Authority and Sand well Health Authority. The Herefordshire application used SSM in the design of an Integrated Care Pathway for stroke patients. In Sandwell, SSM was deployed to assist in the design of an Infonnation Management and Technology (IM&T) Strategy for the boundary-spanning Sandwell Partnership. Both of these environments were experiencing significant organisational change as the experiments unfurled. The explicit objectives of the research were: To examine the evolution and development of SSM and to contribute to its further development. To apply the Soft Systems Methodology to change processes within the NHS. To evaluate the potential role of SSM in this wider process of change. To assess the role of the researcher as a facilitator within this process. To develop a critical framework through which the impact of SSM on change might be understood and assessed. In developing these objectives, it became apparent that there was a gap in knowledge relating to SSM. This gap concerns the evaluation of the role of the approach in the change process. The case studies highlighted issues in stakeholder selection and management; the communicative assumptions in SSM; the ambiguous role of the facilitator; and the impact of highly politicised problem environments on the effectiveness of the methodology in the process of change. An augmented variant on SSM that integrates an appropriate (social constructivist) evaluation method is outlined, together with a series of hypotheses about the operationalisation of this proposed method.

Analysis of secretory, immunostaining and clinical characteristics of human "functionless" pituitary adenomas:transdifferentiation or gonadotropinomas?

In this study, the central technique of in vitro culture has been used to further investigate whether LH/FSH-expressing, but clinically "functionless" pituitary adenomas are gonadotropinomas or whether their hormone secretion is due to transdifferentiation events. 664 "functionless" pituitary adenomas were examined for hormone secretion by in vitro culture and for hormone content by immunostaining. The results were correlated with the clinical findings. 40% of the tumours (n = 263) secreted at least one of the gonadotropins alone, 8% (n = 53) exhibited various patterns of anterior pituitary hormones, whilst the remaining 52% of tumours were not associated with any hormone. In the secretory tumours, immunostaining revealed only a few scattered hormone-containing cells (5 to 15%). Mild hyperprolactinaemia was observed in some cases, presumably because of pressure effects of the tumours. The majority of the patients suffered clear cut hypopituitarism (p < 0.05). Pre-operatively, gonadotropin hypersecretion was observed in 3 cases, but only one of these secreted hormones in culture. Interestingly, a higher proportion of tumours removed from patients with hypopituitarism showed secretory activity in vitro than those tumours removed from patients showing no hormonal dysfunction or hyperprolactinaemia. We conclude that the term "gonadotropinoma" to describe functionless pituitary tumours associated with LH and/or FSH secretion is a misnomer, because the presence of LH and/or FSH confirmed by in vitro methods in the present series is a result of only a few scattered cells. We suggest that primary pituitary tumour cells differentiate into a secretory type (transdifferentiation), possibly in response to altered serum hormone levels such as decreased steroids. Further work is required to identify the factors which trigger the altered cells' characteristics. © J. A. Barth Verlag in Georg Thieme Verlag KG.

Performance modelling and analysis of multiple coexisting IEEE 802.15.4 wireless sensor networks

With the features of low-power and flexible networking capabilities IEEE 802.15.4 has been widely regarded as one strong candidate of communication technologies for wireless sensor networks (WSNs). It is expected that with an increasing number of deployments of 802.15.4 based WSNs, multiple WSNs could coexist with full or partial overlap in residential or enterprise areas. As WSNs are usually deployed without coordination, the communication could meet significant degradation with the 802.15.4 channel access scheme, which has a large impact on system performance. In this thesis we are motivated to investigate the effectiveness of 802.15.4 networks supporting WSN applications with various environments, especially when hidden terminals are presented due to the uncoordinated coexistence problem. Both analytical models and system level simulators are developed to analyse the performance of the random access scheme specified by IEEE 802.15.4 medium access control (MAC) standard for several network scenarios. The first part of the thesis investigates the effectiveness of single 802.15.4 network supporting WSN applications. A Markov chain based analytic model is applied to model the MAC behaviour of IEEE 802.15.4 standard and a discrete event simulator is also developed to analyse the performance and verify the proposed analytical model. It is observed that 802.15.4 networks could sufficiently support most WSN applications with its various functionalities. After the investigation of single network, the uncoordinated coexistence problem of multiple 802.15.4 networks deployed with communication range fully or partially overlapped are investigated in the next part of the thesis. Both nonsleep and sleep modes are investigated with different channel conditions by analytic and simulation methods to obtain the comprehensive performance evaluation. It is found that the uncoordinated coexistence problem can significantly degrade the performance of 802.15.4 networks, which is unlikely to satisfy the QoS requirements for many WSN applications. The proposed analytic model is validated by simulations which could be used to obtain the optimal parameter setting before WSNs deployments to eliminate the interference risks.

Three-dimensional finite element analysis of the effects of anisotropy on bone mechanical properties measured by nanoindentation

A three-dimensional finite element analysis (FEA) model with elastic-plastic anisotropy was built to investigate the effects of anisotropy on nanoindentation measurements for cortical bone. The FEA model has demonstrated a capability to capture the cortical bone material response under the indentation process. By comparison with the contact area obtained from monitoring the contact profile in FEA simulations, the Oliver-Pharr method was found to underpredict or overpredict the contact area due to the effects of anisotropy. The amount of error (less than 10% for cortical bone) depended on the indentation orientation. The indentation modulus results obtained from FEA simulations at different surface orientations showed a trend similar to experimental results and were also similar to moduli calculated from a mathematical model. The Oliver-Pharr method has been shown to be useful for providing first-order approximations in the analysis of anisotropic mechanical properties of cortical bone, although the indentation modulus is influenced by anisotropy.

Analysis of femtosecond laser surface patterning on bulk single-crystalline diamond

Preliminary work is reported on 2-D and 3-D microstructures written directly with a Yb:YAG 1026 nm femtosecond (fs) laser on bulk chemical vapour deposition (CVD) single-crystalline diamond. Smooth graphitic lines and other structures were written on the surface of a CVD diamond sample with a thickness of 0.7mm under low laser fluences. This capability opens up the opportunity for making electronic devices and micro-electromechanical structures on diamond substrates. The fabrication process was optimised through testing a range of laser energies at a 100 kHz repetition rate with sub-500fs pulses. These graphitic lines and structures have been characterised using optical microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and atomic force microscopy. Using these analysis techniques, the formation of sp2 and sp3 bonds is explored and the ratio between sp2 and sp3 bonds after fs laser patterning is quantified. We present the early findings from this study and characterise the relationship between the graphitic line formation and the different fs laser exposure conditions. © 2012 Taylor & Francis.

Coupling in silico and in vitro analysis of peptide-MHC binding:a bioinformatic approach enabling prediction of superbinding peptides and anchorless epitopes

The ability to define and manipulate the interaction of peptides with MHC molecules has immense immunological utility, with applications in epitope identification, vaccine design, and immunomodulation. However, the methods currently available for prediction of peptide-MHC binding are far from ideal. We recently described the application of a bioinformatic prediction method based on quantitative structure-affinity relationship methods to peptide-MHC binding. In this study we demonstrate the predictivity and utility of this approach. We determined the binding affinities of a set of 90 nonamer peptides for the MHC class I allele HLA-A*0201 using an in-house, FACS-based, MHC stabilization assay, and from these data we derived an additive quantitative structure-affinity relationship model for peptide interaction with the HLA-A*0201 molecule. Using this model we then designed a series of high affinity HLA-A2-binding peptides. Experimental analysis revealed that all these peptides showed high binding affinities to the HLA-A*0201 molecule, significantly higher than the highest previously recorded. In addition, by the use of systematic substitution at principal anchor positions 2 and 9, we showed that high binding peptides are tolerant to a wide range of nonpreferred amino acids. Our results support a model in which the affinity of peptide binding to MHC is determined by the interactions of amino acids at multiple positions with the MHC molecule and may be enhanced by enthalpic cooperativity between these component interactions.

Analysis of single and multiple, non-permanent, tunable, birefringent spectral holes in a fibre-Bragg grating stop-band produced via uniaxial pressure

We present an experimental and numerical study of transversely loaded uniform fibre-Bragg gratings. A novel loading configuration is described, producing pressure-induced spectral holes in an initially strong uniform grating. The birefringence properties of these gratings are analysed. It is shown that the frequency splitting of the two spectral holes, corresponding to two orthogonal polarisation states, can be adjusted precisely using this loading configuration. We finally demonstrate a new and simple scheme to induce multiple spectral holes in the stop-band. © 2003 Elsevier Science B.V. All rights reserved.

Statistical Analysis of Data on Linker Histones/DNA Interactions

2000 Mathematics Subject Classification: 62P10, 92C40

Improving the management of behaviour that challenges associated with dementia in care homes:protocol for pharmacy-health psychology intervention feasibility study

INTRODUCTION: The inappropriate use of antipsychotics in people with dementia for behaviour that challenges is associated with an estimated 1800 deaths annually. However, solely focusing on antipsychotics may transfer prescribing to other equally dangerous psychotropics. Little is known about the role of pharmacists in the management of psychotropics used to treat behaviours that challenge. This research aims to determine whether it is feasible to implement and measure the effectiveness of a combined pharmacy-health psychology intervention incorporating a medication review and staff training package to limit the prescription of psychotropics to manage behaviour that challenges in care home residents with dementia. METHODS/ANALYSIS: 6 care homes within the West Midlands will be recruited. People with dementia receiving medication for behaviour that challenges, or their personal consultee, will be approached regarding participation. Medication used to treat behaviour that challenges will be reviewed by the pharmacist, in collaboration with the general practitioner (GP), person with dementia and carer. The behavioural intervention consists of a training package for care home staff and GPs promoting person-centred care and treating behaviours that challenge as an expression of unmet need. The primary outcome measure is the Neuropsychiatric Inventory-Nursing Home version (NPI-NH). Other outcomes include quality of life (EQ-5D and DEMQoL), cognition (sMMSE), health economic (CSRI) and prescribed medication including whether recommendations were implemented. Outcome data will be collected at 6 weeks, and 3 and 6 months. Pretraining and post-training interviews will explore stakeholders' expectations and experiences of the intervention. Data will be used to estimate the sample size for a definitive study. ETHICS/DISSEMINATION: The project has received a favourable opinion from the East Midlands REC (15/EM/3014). If potential participants lack capacity, a personal consultee will be consulted regarding participation in line with the Mental Capacity Act. Results will be published in peer-reviewed journals and presented at conferences.