Geochemistry of picrite basalts from the Liohi Volcano

Research of the ocean floor using the Mir submersibles carried out south of the Hawaiian Archipelago allowed to recover flows of recent picrite basalts. Lava vents are confined to a field of development of open fractures of a gjar type. Basalts represent initial lava flows in the structure of the Hawaiian volcanic archipelago. Considering contents of alkali and rare-earth elements in them, the picrite basalts of the bottom could be assigned to a series of island tholeiites. They are products of high level melting of asthenospheric matter at depth about 75-80 km as a result of decompression near a deep fracture that occurred in the lithosphere and asthenosphere. Similar picrite basalts were found in the base of the youngest volcano of the Hawaiian chain the Loihi Volcano. With respect to contents of alkali metals, these rocks are assigned to the subalkaline series of rocks formed during melting of garnet lherzolites. This could probably be explained by supply of melts from deeper levels of the asthenosphere after partial packing of an initial magma effluent fracture.

Fish biometry and concentration of volatile siloxanes in liver of Atlantic cod (Gadus morhua) and shorthorn sculpin (Myxocephalus scorpius) sampled during RV Lance cruise COPOL in 2009

The purpose of this study was to investigate presence and potential accumulation of cyclic volatile methyl siloxanes (cVMS) in the Arctic environment. Octamethylcyclotetrasiloxane (D4), decamethylcyclopentasiloxane (D5), and dodecamethylcy-clohexasiloxane (D6) were analyzed in sediment, Zooplankton, Atlantic cod (Gadus morhua), shorthorn sculpin (Myxocephalus scorpius), and bearded seal (Erignathus barbatus) collected from the Svalbard archipelago within the European Arctic in July 2009. Highest levels were found for D5 in fish collected from Adventfjorden, with average concentrations of 176 and 531 ng/g lipid in Atlantic cod and shorthorn sculpin, respectively. Decreasing concentration of D5 in sediment collected away from waste water outlet in Adventfjorden indicates that the local settlement of Longyearbyen is a point source to the local aquatic environment. Median biota sediment accumulation factors (BSAFs) calculated for D5 in Adventfjorden were 2.1 and 1.5 for Atlantic cod and shorthorn sculpin, respectively. Biota concentrations of D5 were lower or below detection limits in remote and sparsely populated regions (Kongsfjorden and Liefdefjorden) compared to Adventfjorden. The levels of cVMS were found to be low or below detection limits in bearded seal blubber and indicate a low risk for cVMS accumulation within mammals. Accumulation of cVMS in fish appears to be influenced by local exposure from human settlements within the Arctic.

Chloroflexus spp. and Sulfurihydrogenibium spp. in microbial mats of the Nakabusa hot spring, Japan

Microbial mats develop in a wide range of aquatic habitats, such as geothermal hot springs, hypersaline ponds, marine cold seeps or hydrothermal vents. The Nakabusa hot spring is located in the Nagano Prefecture, Japan (36.3875N, 137.75E), dense olive-green microbial mats develop in regions where the slightly alkaline, sulfidic effluent has cooled to 65°C. The microbial community of such mats was analyzed by focusing on the diversity, as well as the in situ distribution and function of bacteria involved in sulfur cycling. Microbial mat samples were kept in sterile plastic tubes (for molecular analysis) or glass bottles completely filled with hot spring water to avoid oxidation. Samples were transferred to the laboratory on ice and used for physiological experiments within 8h. Quantification of cell biovolumes was carried out based on images of mat sections hybridized with Sulfurihydrogenibium- and Chloroflexi-specific probes, and stained with DAPI. In situ hybridizations (CARD-FISH) of thin matsections showed a heterogeneous vertical distribution of Sulfurihydrogenibium and Chloroflexus. Sulfurihydrogenibium dominated near the mat surface (50% of the total mat biovolume), while Chloroflexus dominated in deeper layers (up to 64% of the total mat biovolume).

A ferrous oxalate mediated photo-Fenton system: Toward an increased biodegradability of indigo dyed wastewaters

This study assessed the applicability of a ferrous oxalate mediated photo-Fenton pretreatment for indigo-dyed wastewaters as to produce a biodegradable enough effluent, likely of being derived to conventional biological processes. The photochemical treatment was performed with ferrous oxalate and hydrogen peroxide in a Compound Parabolic Concentrator (CPC) under batch operation conditions. The reaction was studied at natural pH conditions (5–6) with indigo concentrations in the range of 6.67–33.33 mg L−1, using a fixed oxalate-to-iron mass ratio (C2O42−/Fe2+ = 35) and assessing the system's biodegradability at low (257 mg L−1) and high (1280 mg L−1) H2O2 concentrations. In order to seek the optimal conditions for the treatment of indigo dyed wastewaters, an experimental design consisting in a statistical surface response approach was carried out. This analysis revealed that the best removal efficiencies for Total Organic Carbon (TOC) were obtained for low peroxide doses. In general it was observed that after 20 kJ L−1, almost every treated effluent increased its biodegradability from a BOD5/COD value of 0.4. This increase in the biodegradability was confirmed by the presence of short chain carboxylic acids as intermediate products and by the mineralization of organic nitrogen into nitrate. Finally, an overall decrease in the LC50 for Artemia salina indicated a successful detoxification of the effluent.

Geochemical fingerprints and controls in the sediments of an urban river: River Manzanares, Madrid (Spain)

The geochemical fingerprint of sediment retrieved from the banks of the River Manzanares as it passes through the City of Madrid is presented here. The river collects the effluent water from several Waste Water Treatment (WWT) plants in and around the city, such that, at low flows, up to 60% of the flow has been treated. A total of 18 bank-sediment cores were collected along the course of the river, down to its confluence with the Jarama river, to the south–east of Madrid. Trace and major elements in each sample were extracted following a double protocol: (a) “Total” digestion with HNO3, HClO4 and HF; (b) “Weak” digestion with sodium acetate buffered to pH=5 with acetic acid, under constant stirring. The digests thus obtained were subsequently analysed by ICP-AES, except for Hg which was extracted with aqua regia and sodium chloride-hydroxylamine sulfate, and analysed by Cold Vapour-AAS. X-ray diffraction was additionally employed to determine the mineralogical composition of the samples. Uni- and multivariate analyses of the chemical data reveal the influence of Madrid on the geochemistry of Manzanares' sediments, clearly manifested by a marked increase in the concentration of typically “urban” elements Ag, Cr, Cu, Pb and Zn, downstream of the intersection of the river with the city's perimeter. The highest concentrations of these elements appear to be associated with illegal or accidental dumping of waste materials, and with the uncontrolled incorporation of untreated urban runoff to the river. The natural matrix of the sediment is characterised by fairly constant concentrations of Ce, La and Y, whereas changes in the lithology intersected by the river cause corresponding variations in Ca–Mg and Al–Na contents. In the final stretch of the river, the presence of carbonate materials seems to exert a strong geochemical control on the amount of Zn and, to a lesser extent, Cu immobilised in the sediments. This fact suggests that a variable but significant proportion of both elements may be susceptible to reincorporation in the aqueous phase under realistic environmental conditions.

Estudio de la digestión anaerobia en dos fases para el tratamiento de las aguas residuales de despulpe del beneficiado húmedo del café

Debido al aumento de los estándares de calidad exigidos internacionalmente, así como por una mayor presión sobre la industria mediante legislaciones ambientales más rigurosas, el sector cafetalero está obligado a buscar, a través de la investigación, un sistema adecuado de tratamiento para las aguas residuales generadas en el beneficiado húmedo del café. En este trabajo se evaluó el funcionamiento de la digestión anaerobia para el tratamiento de las aguas residuales de despulpe. Para ello, se utilizaron dos sistemas anaerobios, uno en una etapa (UASB), y otro con separación de fases (2PUASB). Se investigó el efecto en la digestión anaerobia de tres cargas orgánicas volumétricas (OLR) y de las dos configuraciones de reactor usadas. Los valores de OLR de operación en el sistema UASB variaron en un intervalo de 3.6-4.1 kgCOD m-3 d-1, con una tasa de recirculación del efluente de 1.0. El sistema 2PUASB fue alimentado con OLR similares a las que se emplearon en el sistema en una etapa. El reactor de acidificación fue cargado a 11.0 kgCOD m-3 d-1, mientras que en el reactor metanogénico varió en el intervalo de 2.6-4.67 kgCOD m-3 d-1. El uso de reactores UASB en una etapa y en dos fases, bajo las mismas condiciones de operación ya descritas, propiciaron el logro de una eficiencia de degradación de COD total superior al 75% y al 85% para la COD soluble, respectivamente. Sin embargo, el sistema en dos fases mostró mejores resultados en el tratamiento de este tipo de agua residual, no solo en cuanto a eficiencia de eliminación de la carga orgánica contaminante así como una menor concentración de ácidos grasos volátiles (VFA) en el efluente. Obtenidas las mejores condiciones de trabajo, fue evaluada la separación de fases bajo el efecto de la recirculación. Los grupos de fermentaciones producidos fueron similares a los obtenidos en el experimento sin recirculación, indicando que está última no afectó la composición relativa de los VFA del reactor anaerobio, por lo que no cambió el patrón de degradación del residuo. Una tasa de recirculación de 1.0 del efluente del reactor metanogénico al reactor acidogénico mejoró significativamente el proceso, ya que se incrementó la conversión de los VFA (31%), la eliminación de la fracción total y soluble del residuo tratado (6.5%) y la reducción del consumo de alcalinizante (39%); manteniendo similares producciones de metano. El uso de la digestión anaerobia en dos fases demostró una mejora en la estabilidad del proceso y un incremento de la eficiencia de operación y de la producción de metano, respectivamente.Tesis Doctoral Yans Guardia Puebla Abstract ix ABSTRACT Due to the increase of quality standards internationally demanded, as well as for a greater pressure on the industry by means of more rigorous environmental legislations, the coffee sector is forced to search, through the research, an appropriated treatment system for coffee wet wastewaters generated. In this work the performance of the anaerobic digestion for the coffee wet wastewater treatment was evaluated. For it, two anaerobic systems, one in single-stage (UASB), and another with two-phase (2PUASB) were used. The effect in the anaerobic digestion of three organic loading rates (OLR) and of two reactor configurations used was investigated. OLR operation values in UASB system varied in an interval of 3.6-4.1 kgCOD m-3 d-1, with a recycle rate of the effluent of 1.0. 2PUASB system was fed with OLR similar to those that were used in the reactor in a stage. The acidification reactor was loaded to 11.0 kgCOD m-3 d-1, whereas in the methanogenic reactor varied in the interval of 2.6-4.67 kgCOD m-3 d-1. The use of single-stage and two-phase UASB reactors, under the same operation conditions already before described, a total COD removal efficiency of 75% and 85% for the soluble COD removal efficiency, respectively, was achieved. However, two-phase system showed better results in the treatment of this wastewater type, not only as for removal efficiency of loading organic polluting as well as a smaller volatile fatty acid (VFA) concentration in the effluent. Obtained the best work conditions, the two-phase system under the effect of the recycle was evaluated. Fermentations groups produced were similar to those obtained in the experiment without recycle, indicating that it last one do not affect the relative composition of VFA of the anaerobic reactor, for that reason the degradation pattern of the residue does not change. A recycle rate of 1.0 of the effluent of the methanogenic reactor to the acidogenic reactor improved the process significantly, since it was increased the VFA conversion (31%), the removal of total and soluble fraction of the residue treated (6.5%) and the decrease of the alkalinity consumption (39%); maintaining similar methane productions. The use of the two-phase anaerobic digestion demonstrated to an improvement in the stability of the process and an increase of the operation efficiency and methane production, respectively.

Recuperación de energía de la salmuera

Como consecuencia del proceso de desalación, se produce el vertido al mar de un agua de rechazo hipersalino o salmuera. La salinidad de este vertido es variable, dependiendo del origen de la captación y del proceso de tratamiento. Muchos de los hábitats y biocenosis de los ecosistemas marinos se encuentran adaptados a ambientes de salinidad casi constante y son muy susceptibles a los incrementos de salinidad originados por estos vertidos. Junto con el vertido de salmuera otro de los principales inconvenientes que plantean las plantas desaladoras es el alto consumo energético, con todas las desventajas que esto supone: alto coste del agua desalada para los consumidores, contaminación del medio... El desarrollo de los métodos de vertido, herramientas de gestión de la salmuera, estudios del comportamiento de la pluma salina… ha buscado la mitigación de estos efectos sobre los ecosistemas marinos. El desarrollo en membranas de ósmosis inversa, diseño de bombas y sistemas de recuperación de energía ha permitido también la reducción del consumo energético en las plantas de desalación. Sin embargo, estos campos parecen haber encontrado un techo tecnológico difícil de rebasar en los últimos tiempos. La energía osmótica se plantea como uno de los caminos a investigar aplicado al campo de la reducción del consumo energético en desalación de agua de mar, a través del aprovechamiento energético de la salmuera. Con esta tesis se pretende cumplir principalmente con los siguientes objetivos: reducción del consumo energético en desalación, mitigar el impacto del vertido sobre el medio y ser una nueva herramienta en la gestión de la salmuera. En el presente documento se plantea el desarrollo de un nuevo proceso que utiliza el fenómeno de la ósmosis directa a través de membranas semipermeables, y busca la sinergia desalación depuración, integrando ambos, en un único proceso de tratamiento dentro del ciclo integral del agua. Para verificar los valores de producción, calidad y rendimiento del proceso, se proyecta y construye una planta piloto ubicada en la Planta Desaladora de Alicante II, escalada de tal manera que permite la realización de los ensayos con equipos comerciales de tamaño mínimo. El objetivo es que el resultado final sea extrapolable a tamaños superiores sin que el escalado afecte a la certeza y fiabilidad de las conclusiones obtenidas. La planta se proyecta de forma que el vertido de una desaladora de ósmosis inversa junto con el vertido de un terciario convencional, se pasan por una ósmosis directa y a continuación por una ósmosis inversa otra vez, ésta última con el objeto de abrir la posibilidad de incrementar la producción de agua potable. Ambas ósmosis están provistas de un sistema de pretratamiento físico-químico (para adecuar la calidad del agua de entrada a las condiciones requeridas por las membranas en ambos casos), y un sistema de limpieza química. En todos los ensayos se usa como fuente de disolución concentrada (agua salada), el rechazo de un bastidor de ósmosis inversa de una desaladora convencional de agua de mar. La fuente de agua dulce marca la distinción entre dos tipos de ensayos: ensayos con el efluente del tratamiento terciario de una depuradora convencional, con lo que se estudia el comportamiento de la membrana ante el ensuciamiento; y ensayos con agua permeada, que permiten estudiar el comportamiento ideal de la membrana. Los resultados de los ensayos con agua salobre ponen de manifiesto problemas de ensuciamiento de la membrana, el caudal de paso a través de la misma disminuye con el tiempo y este efecto se ve incrementado con el aumento de la temperatura del agua. Este fenómeno deriva en una modificación del pretratamiento de la ósmosis directa añadiendo un sistema de ultrafiltración que ha permitido que la membrana presente un comportamiento estable en el tiempo. Los ensayos con agua permeada han hecho posible estudiar el comportamiento “ideal” de la membrana y se han obtenido las condiciones óptimas de operación y a las que se debe tender, consiguiendo tasas de recuperación de energía de 1,6; lo que supone pasar de un consumo de 2,44 kWh/m3 de un tren convencional de ósmosis a 2,28 kWh/m3 al añadir un sistema de ósmosis directa. El objetivo de futuras investigaciones es llegar a tasas de recuperación de 1,9, lo que supondría alcanzar consumos inferiores a 2 kWh/m3. Con esta tesis se concluye que el proceso propuesto permite dar un paso más en la reducción del consumo energético en desalación, además de mitigar los efectos del vertido de salmuera en el medio marino puesto que se reduce tanto el caudal como la salinidad del vertido, siendo además aplicable a plantas ya existentes y planteando importantes ventajas económicas a plantas nuevas, concebidas con este diseño. As a consequence of the desalination process, a discharge of a hypersaline water or brine in the sea is produced. The salinity of these discharges varies, depending on the type of intake and the treatment process. Many of the habitats and biocenosis of marine ecosystems are adapted to an almost constant salinity environment and they are very susceptible to salinity increases caused by these discharges. Besides the brine discharge, another problem posed by desalination plants, is the high energy consumption, with all the disadvantages that this involves: high cost of desalinated water for consumers, environmental pollution ... The development of methods of disposal, brine management tools, studies of saline plume ... has sought the mitigation of these effects on marine ecosystems. The development of reverse osmosis membranes, pump design and energy recovery systems have also enabled the reduction of energy consumption in desalination plants. However, these fields seem to have reached a technological ceiling which is difficult to exceed in recent times. Osmotic power is proposed as a new way to achieve the reduction of energy consumption in seawater desalination, through the energy recovery from the brine. This thesis mainly tries to achieve the following objectives: reduction of energy consumption in desalination, mitigation of the brine discharge impact on the environment and become a new tool in the management of the brine. This paper proposes the development of a new process, that uses the phenomenon of forward osmosis through semipermeable membranes and seeks the synergy desalination-wastewater reuse, combining both into a single treatment process within the integral water cycle. To verify the production, quality and performance of the process we have created a pilot plant. This pilot plant, located in Alicante II desalination plant, has been designed and built in a scale that allows to carry out the tests with minimum size commercial equipment. The aim is that the results can be extrapolated to larger sizes, preventing that the scale affects the accuracy and reliability of the results. In the projected plant, the discharge of a reverse osmosis desalination plant and the effluent of a convencional tertiary treatment of a wastewater plant, go through a forward osmosis module, and then through a reverse osmosis, in order to open the possibility of increasing potable water production. Both osmosis systems are provided with a physicochemical pretreatment (in order to obtain the required conditions for the membranes in both cases), and a chemical cleaning system. In all tests, it is used as a source of concentrated solution (salt water), the rejection of a rack of a conventional reverse osmosis seawater desalination. The source of fresh water makes the difference between two types of tests: test with the effluent from a tertiary treatment of a conventional wastewater treatment plant (these tests study the behavior of the membrane facing the fouling) and tests with permeate, which allow us to study the ideal behavior of the membrane. The results of the tests with brackish water show fouling problems, the flow rate through the membrane decreases with the time and this effect is increased with water temperature. This phenomenon causes the need for a modification of the pretreatment of the direct osmosis module. An ultrafiltration system is added to enable the membrane to present a stable behavior . The tests with permeate have made possible the study of the ideal behavior of the membrane and we have obtained the optimum operating conditions. We have achieved energy recovery rates of 1.6, which allows to move from a consumption of 2.44 kWh/m3 in a conventional train of reverse osmosis to 2.28 kWh / m3 if it is added the direct osmosis system. The goal of future researches is to achieve recovery rates of 1.9, which would allow to reach a consumption lower than 2 kWh/m3. This thesis concludes that the proposed process allows us to take a further step in the reduction of the energy consumption in desalination. We must also add the mitigation of the brine discharge effects on the marine environment, due to the reduction of the flow and salinity of the discharge. This is also applicable to existing plants, and it suggests important economic benefits to new plants that will be built with this design.

Numerical models for coastal zone management

The basic equations for modelling two-dimensional hydrodynamics and transport in estuaries and coastal regions have been developed. By using the finite element method, it is possible to transform the model into a discretized counterpart. The model has been applied in order to study the dispersion of an effluent within the Bay of Santander. The results obtained by means of a computer program are discussed.

La reutilización de efluentes depurados en España: retrospectiva, desarrollo del marco normativo, estudio de las tecnologías de regeneración frente a los biorreactores de membrana y sus costes en función del uso

La reutilización de efluentes depurados siempre ha sido una opción en lugares con déficit coyuntural o estructural de recursos hídricos, se haya o no procedido a la regulación y planificación de esta práctica. La necesidad se crea a partir de las demandas de una zona, normalmente riego agrícola, que ven un mejor desarrollo de su actividad por contar con este recurso. España es el país de la UE que más caudal reutiliza, y está dentro de los diez primeros a nivel mundial. La regulación de esta práctica por el RD 1620/2007, ayudó a incorporar la reutilización de efluentes depurados a la planificación hidrológica como parte de los programas de medidas, con objeto de mitigar presiones, como son las extracciones de agua superficial y subterránea, o mejoras medioambientales evitando un vertido. El objeto de este trabajo es conocer la situación de la reutilización de efluentes depurados en España, los diferentes escenarios y planteamientos de esta actividad, el desarrollo del marco normativo y su aplicabilidad, junto a los tratamientos que permiten alcanzar los límites de calidad establecidos en la normativa vigente, en función de los distintos usos. Además, se aporta un análisis de costes de las distintas unidades de tratamiento y tipologías de líneas de regeneración, tanto de las utilizadas después de un tratamiento secundario como de otras opciones de depuración, como son los biorreactores de membrana (MBRs). Para el desarrollo de estos objetivos, en primer lugar, se aborda el conocimiento de la situación de la reutilización en España a través de una base de datos diseñada para cubrir todos los aspectos de esta actividad: datos de la estación depuradora de aguas residuales (EDAR), de la estación regeneradora (ERA), caudales depurados, reutilizados, volúmenes utilizados y ubicación de los distintos usos, tipos de líneas de tratamiento, calidades del agua reutilizada, etc. Las principales fuentes de información son las Confederaciones Hidrográficas (CCHH) a través de las concesiones de uso del agua depurada, las entidades de saneamiento y depuración de las distintas comunidades autónomas (CCAA), ayuntamientos, Planes Hidrológicos de Cuenca (PHC) y visitas a las zonas más emblemáticas. Además, se revisan planes y programas con el fin de realizar una retrospectiva de cómo se ha ido consolidando y desarrollando esta práctica en las distintas zonas de la geografía española. Se han inventariado 322 sistemas de reutilización y 216 tratamientos de regeneración siendo el más extendido la filtración mediante filtro arena seguido de una desinfección mediante hipoclorito, aunque este tratamiento se ha ido sustituyendo por un físico-químico con decantación lamelar, filtro de arena y radiación ultravioleta, tratamiento de regeneración convencional (TRC), y otros tratamientos que pueden incluir membranas, tratamientos de regeneración avanzados (TRA), con dosificación de hipoclorito como desinfección residual, para adaptarse al actual marco normativo. El uso más extendido es el agrícola con el 70% del caudal total reutilizado, estimado en 408 hm3, aunque la capacidad de los tratamientos de regeneración esperada para 2015, tras el Plan Nacional de Reutilización de Aguas (PNRA), es tres veces superior. Respecto al desarrollo normativo, en las zonas donde la reutilización ha sido pionera, las administraciones competentes han ido desarrollando diferentes recomendaciones de calidad y manejo de este tipo de agua. El uso agrícola, y en zonas turísticas, el riego de campos de golf, fueron los dos primeros usos que tuvieron algún tipo de recomendación incluso reglamentación. Esta situación inicial, sin una normativa a nivel estatal ni recomendaciones europeas, creó cierta incertidumbre en el avance de la reutilización tanto a nivel de concesiones como de planificación. En la actualidad sigue sin existir una normativa internacional para la reutilización y regeneración de efluentes depurados. Las recomendaciones de referencia a nivel mundial, y en concreto para el uso agrícola, son las de la OMS (Organización Mundial de la Salud) publicadas 1989, con sus posteriores revisiones y ampliaciones (OMS, 2006). Esta norma combina tratamientos básicos de depuración y unas buenas prácticas basadas en diferentes niveles de protección para evitar problemas sanitarios. Otra normativa que ha sido referencia en el desarrollo del marco normativo en países donde se realiza esta práctica, son las recomendaciones dadas por la Agencia Medioambiente Estadunidense (USEPA, 2012) o las publicadas por el Estado de California (Título 22, 2001). Estas normas establecen unos indicadores y valores máximos dónde el tratamiento de regeneración es el responsable de la calidad final en función del uso. Durante 2015, la ISO trabajaba en un documento para el uso urbano donde se muestra tanto los posibles parámetros que habría que controlar como la manera de actuar para evitar posibles riesgos. Por otro lado, la Comisión Europea (CE) viene impulsando desde el 2014 la reutilización de aguas depuradas dentro del marco de la Estrategia Común de Implantación de la Directiva Marco del Agua, y fundamentalmente a través del grupo de trabajo de “Programas de medidas”. Para el desarrollo de esta iniciativa se está planteando sacar para 2016 una guía de recomendaciones que podría venir a completar el marco normativo de los distintos Estados Miembros (EM). El Real Decreto 1620/2007, donde se establece el marco jurídico de la reutilización de efluentes depurados, tiende más a la filosofía implantada por la USEPA, aunque la UE parece más partidaria de una gestión del riesgo, donde se establecen unos niveles de tolerancia y unos puntos de control en función de las condiciones socioeconómicas de los distintos Estados, sin entrar a concretar indicadores, valores máximos o tratamientos. Sin embargo, en la normativa estadounidense se indican una serie de tratamientos de regeneración, mientras que, en la española, se hacen recomendaciones a este respecto en una Guía sin validez legal. Por tanto, queda sin regular los procesos para alcanzar estos estándares de calidad, pudiendo ser éstos no apropiados para esta práctica. Es el caso de la desinfección donde el uso de hipoclorito puede generar subproductos indeseables. En la Guía de recomendaciones para la aplicación del RD, publicada por el Ministerio de Agricultura y Medioambiente (MAGRAMA) en 2010, se aclaran cuestiones frecuentes sobre la aplicación del RD, prescripciones técnicas básicas para los sistemas de reutilización, y buenas prácticas en función del uso. Aun así, el RD sigue teniendo deficiencias en su aplicación siendo necesaria una revisión de la misma, como en las frecuencias de muestreo incluso la omisión de algunos parámetros como huevos de nematodos que se ha demostrado ser inexistentes tras un tratamiento de regeneración convencional. En este sentido, existe una tendencia a nivel mundial a reutilizar las aguas con fines de abastecimiento, incluir indicadores de presencia de virus o protozoos, o incluir ciertas tecnologías como las membranas u oxidaciones avanzadas para afrontar temas como los contaminantes emergentes. Otro de los objetivos de este trabajo es el estudio de tipologías de tratamiento en función de los usos establecidos en el RD 1620/2007 y sus costes asociados, siendo base de lo establecido a este respecto en la Guía y PNRA anteriormente indicados. Las tipologías de tratamiento propuestas se dividen en líneas con capacidad de desalar y las que no cuentan con una unidad de desalación de aguas salobres de ósmosis inversa o electrodiálisis reversible. Se realiza esta división al tener actuaciones en zonas costeras donde el agua de mar entra en los colectores, adquiriendo el agua residual un contenido en sales que es limitante en algunos usos. Para desarrollar este objetivo se han estudiado las unidades de tratamiento más implantadas en ERAs españolas en cuanto a fiabilidad para conseguir determinada calidad y coste, tanto de implantación como de explotación. El TRC, tiene un coste de implantación de 28 a 48 €.m-3.d y de explotación de 0,06 a 0,09 €. m-3, mientras que, si se precisara desalar, este coste se multiplica por diez en la implantación y por cinco en la explotación. En caso de los usos que requieren de TRA, como los domiciliarios o algunos industriales, los costes serían de 185 a 398 €.m-3.d en implantación y de 0,14 a 0,20 €.m-3 en explotación. En la selección de tecnologías de regeneración, la capacidad del tratamiento en relación al coste es un indicador fundamental. Este trabajo aporta curvas de tendencia coste-capacidad que sirven de herramienta de selección frente a otros tratamientos de regeneración de reciente implantación como son los MBR, u otros como la desalación de agua de mar o los trasvases entre cuencas dentro de la planificación hidrológica. En España, el aumento de las necesidades de agua de alta calidad en zonas con recursos escasos, aumento de zonas sensibles como puntos de captación para potables, zonas de baño o zonas de producción piscícola, y en ocasiones, el escaso terreno disponible para la implantación de nuevas plantas depuradoras (EDARs), han convertido a los MBRs, en una opción dentro del marco de la reutilización de aguas depuradas. En este trabajo, se estudia esta tecnología frente a los TRC y TRA, aportando igualmente curvas de tendencia coste-capacidad, e identificando cuando esta opción tecnológica puede ser más competitiva frente a los otros tratamientos de regeneración. Un MBR es un tratamiento de depuración de fangos activos donde el decantador secundario es sustituido por un sistema de membranas de UF o MF. La calidad del efluente, por tanto, es la misma que el de una EDAR seguida de un TRA. Los MBRs aseguran una calidad del efluente para todos los usos establecidos en el RD, incluso dan un efluente que permite ser directamente tratado por las unidades de desalación de OI o EDR. La implantación de esta tecnología en España ha tenido un crecimiento exponencial, pasando de 13 instalaciones de menos de 5.000 m3. d-1 en el 2006, a más de 55 instalaciones en operación o construcción a finales del 2014, seis de ellas con capacidades por encima de los 15.000 m3. d-1. Los sistemas de filtración en los MBR son los que marcan la operación y diseño de este tipo de instalaciones. El sistema más implantado en España es de membrana de fibra hueca (MFH), sobre todo para instalaciones de gran capacidad, destacando Zenon que cuenta con el 57% de la capacidad total instalada. La segunda casa comercial con mayor número de plantas es Kubota, con membranas de configuración placa plana (MPP), que cuenta con el 30 % de la capacidad total instalada. Existen otras casas comerciales implantadas en MBR españoles como son Toray, Huber, Koch o Microdym. En este documento se realiza la descripción de los sistemas de filtración de todas estas casas comerciales, aportando información de sus características, parámetros de diseño y operación más relevantes. El estudio de 14 MBRs ha posibilitado realizar otro de los objetivos de este trabajo, la estimación de los costes de explotación e implantación de este tipo de sistemas frente a otras alternativas de tratamiento de regeneración. En este estudio han participado activamente ACA y ESAMUR, entidades públicas de saneamiento y depuración de Cataluña y Murcia respectivamente, que cuentan con una amplia experiencia en la explotación de este tipo de sistemas. Este documento expone los problemas de operación encontrados y sus posibles soluciones, tanto en la explotación como en los futuros diseños de este tipo de plantas. El trabajo concluye que los MBRs son una opción más para la reutilización de efluentes depurados, siendo ventajosos en costes, tanto de implantación como de explotación, respecto a EDARs seguidas de TRA en capacidades por encima de los 10.000 m3.d-1. ABSTRACT The reuse of treated effluent has always been an option in places where a situational or structural water deficit exists, whether regulatory and/or planning efforts are completed or not. The need arises from the demand of a sector, commonly agricultural irrigation, which benefits of this new resource. Within the EU, Spain is ahead in the annual volume of reclaimed water, and is among the top ten countries at a global scale. The regulation of this practice through the Royal Decree 1620/2007 has helped to incorporate the water reuse to the hydrological plans as a part of the programme of measures to mitigate pressures such as surface or ground water extraction, or environmental improvements preventing discharges. The object of this study is to gain an overview of the state of the water reuse in Spain, the different scenarios and approaches to this activity, the development of the legal framework and its enforceability, together with the treatments that achieve the quality levels according to the current law, broken down by applications. Additionally, a cost analysis of technologies and regeneration treatment lines for water reclamation is performed, whereas the regeneration treatment is located after a wastewater treatment or other options such as membrane bioreactors (MBR). To develop the abovementioned objectives, the state of water reuse in Spain is studied by means of a database designed to encompass all aspects of the activity: data from the wastewater treatment plants (WWTP), from the water reclamation plants (WRP), the use of reclaimed water, treated water and reclaimed water annual volumes and qualities, facilities and applications, geographic references, technologies, regeneration treatment lines, etc. The main data providers are the River Basin authorities, through the concession or authorization for water reuse, (sanitary and wastewater treatment managers from the territorial governments, local governments, Hydrological Plans of the River Basins and field visits to the main water reuse systems. Additionally, a review of different plans and programmes on wastewater treatment or water reuse is done, aiming to put the development and consolidation process of this activity in the different regions of Spain in perspective. An inventory of 322 reuse systems and 216 regeneration treatments has been gathered on the database, where the most extended regeneration treatment line was sand filtration followed by hypochlorite disinfection, even though recently it is being replaced by physical–chemical treatment with a lamella settling system, depth sand filtration, and a disinfection with ultraviolet radiation and hypochlorite as residual disinfectant, named conventional regeneration treatment (CRT), and another treatment that may include a membrane process, named advanced regeneration treatment (ART), to adapt to legal requirements. Agricultural use is the most extended, accumulating 70% of the reclaimed demand, estimated at 408 hm3, even though the expected total capacity of WRPs for 2015, after the implementation of the National Water Reuse Plan (NWRP) is three times higher. According to the development of the water reuse legal framework, there were pioneer areas where competent authorities developed different quality and use recommendations for this new resource. Agricultural use and golf course irrigation in touristic areas were the first two uses with recommendations and even legislation. The initial lack of common legislation for water reuse at a national or European level created some doubts which affected the implementation of water reuse, both from a planning and a licensing point of view. Currently there is still a lack of common international legislation regarding water reuse, technologies and applications. Regarding agricultural use, the model recommendations at a global scale are those set by the World Health Organization published in 1989, and subsequent reviews and extensions about risk prevention (WHO, 2006). These documents combine wastewater treatments with basic regeneration treatments reinforced by good practices based on different levels of protection to avoid deleterious health effects. Another relevant legal reference for this practices has been the Environmental Protection Agency of the US (USEPA, 2012), or those published by the State of California (Title 22, 2001). These establish indicator targets and maximum thresholds where regeneration treatment lines are responsible for the final quality according to the different uses. During 2015, the ISO has worked on a document aimed at urban use, where the possible parameters to be monitored together with risk prevention have been studied. On the other hand, the European Commission has been promoting the reuse of treated effluents within the Common Implementation Strategy of the Water Framework Directive, mainly through the work of the Programme of Measures Working Group. Within this context, the publication of a recommendation guide during 2016 is intended, as a useful tool to fill in the legal gaps of different Member States on the matter. The Royal Decree 1620/2007, where the water reuse regulation is set, resembles the principles of the USEPA more closely, even though the EU shows a tendency to prioritize risk assessment by establishing tolerance levels and thresholds according to socioeconomic conditions of the different countries, without going into details of indicators, maximum thresholds or treatments. In contrast, in the US law, regeneration treatments are indicated, while in the Spanish legislation, the only recommendations to this respect are compiled in a non-compulsory guide. Therefore, there is no regulation on the different treatment lines used to achieve the required quality standards, giving room for inappropriate practices in this respect. This is the case of disinfection, where the use of hypochlorite may produce harmful byproducts. In the recommendation Guide for the application of the Royal Decree (RD), published by the Ministry of Agriculture and Environment (MAGRAMA) in 2010, clarifications of typical issues that may arise from the application of the RD are given, as well as basic technical parameters to consider in reuse setups, or good practices according to final use. Even so, the RD still presents difficulties in its application and requires a review on issues such as the sampling frequency of current quality parameters or even the omission of nematode eggs indicator, which have been shown to be absent after CRT. In this regard, there is a global tendency to employ water reuse for drinking water, including indicators for the presence of viruses and protozoans, or to include certain technologies such as membranes or advanced oxidation processes to tackle problems like emerging pollutants. Another of the objectives of this study is to provide different regeneration treatment lines to meet the quality requirements established in the RD 1620/2007 broken down by applications, and to estimate establishment and operational costs. This proposal has been based on what is established in the above mentioned Guide and NWRP. The proposed treatment typologies are divided in treatment trains with desalination, like reverse osmosis or reversible electrodialisis, and those that lack this treatment for brackish water. This separation is done due to coastal facilities, where sea water may permeate the collecting pipes, rising salt contents in the wastewater, hence limiting certain uses. To develop this objective a study of the most common treatment units set up in Spanish WRPs is conducted in terms of treatment train reliability to obtain an acceptable relationship between the required quality and the capital and operational costs. The CRT has an establishment cost of 28 to 48 €.m-3.d and an operation cost of 0.06 to 0.09 €.m-3, while, if desalination was required, these costs would increase tenfold for implementation and fivefold for operation. In the cases of uses that require ART, such as residential or certain industrial uses, the costs would be of 185 to 398 €.m-3.d for implementation and of 0.14 to 0.20 €.m-3 for operation. When selecting regeneration treatment lines, the relation between treatment capacity and cost is a paramount indicator. This project provides cost-capacity models for regeneration treatment trains. These may serve as a tool when selecting between different options to fulfill water demands with MBR facilities, or others such as sea water desalination plants or inter-basin water transfer into a water planning framework. In Spain, the requirement for high quality water in areas with low resource availability, the increasing number of sensitive zones, such as drinking water extraction, recreational bathing areas, fish protected areas and the lack of available land to set up new WWTPs, have turned MBRs into a suitable option for water reuse. In this work this technology is analyzed in contrast to CRT and ART, providing cost-capacity models, and identifying when and where this treatment option may outcompete other regeneration treatments. An MBR is an activated sludge treatment where the secondary settling is substituted by a membrane system of UF or MF. The quality of the effluent is, therefore, comparable to that of a WWTP followed by an ART. MBRs ensure a sufficient quality level for the requirements of the different uses established in the RD, even producing an effluent that can be directly treated in OI or EDR processes. The implementation of this technology in Spain has grown exponentially, growing from 13 facilities with less than 5000 m3.d-1 in 2006 to above 55 facilities operating by the end of 2014, 6 of them with capacities over 15000 m3.d-1. The membrane filtration systems for MBR are the ones that set the pace of operation and design of this type of facilities. The most widespread system in Spain is the hollow fiber membrane configuration, especially on high flow capacities, being Zenon commercial technology, which mounts up to 57% of the total installed capacity, the main contributor. The next commercial technology according to plant number is Kubota, which uses flat sheet membrane configuration, which mounts up to 30% of the total installed capacity. Other commercial technologies exist within the Spanish MBR context, such as Toray, Huber, Koch or Microdym. In this document an analysis of all of these membrane filtration systems is done, providing information about their characteristics and relevant design and operation parameters. The study of 14 full scale running MBRs has enabled to pursue another of the objectives of this work: the estimation of the implementation and operation costs of this type of systems in contrast to other regeneration alternatives. Active participation of ACA and ESAMUR, public wastewater treatment and reuse entities of Cataluña and Murcia respectively, has helped attaining this objective. A number of typical operative problems and their possible solutions are discussed, both for operation and plant design purposes. The conclusion of this study is that MBRs are another option to consider for water reuse, being advantageous in terms of both implementation and operational costs, when compared with WWTPs followed by ART, when considering flow capacities above 10000 m3.d-1.

Tratamiento de vinazas provenientes de etanol en un reactor de lecho fluidizado inverso

En el estado de Veracruz, al sur de México, se ubican empresas dedicadas a la obtención de etanol a partir de melaza de azúcar de caña. Las más pequeñas, tienen una producción promedio de 20,000 L de alcohol/día. Los efluentes de la producción de etanol incluyen agua de enfriamiento de condensadores, agua del lavado de tanques de fermentación y vinazas, estas últimas son los efluentes más contaminantes en las destilerías, por su concentración de material orgánico biodegradable y no biodegradable. Las vinazas se generan en grandes volúmenes, produciéndose de 12 a 15 litros de vinazas por cada litro de alcohol destilado. Estos efluentes se caracterizan por tener altas temperaturas, pH ácido y una elevada concentración de DQO así como de sólidos totales. La determinación de la biodegradabilidad anaerobia de un agua residual, permite estimar la fracción de DQO que puede ser transformada potencialmente en metano y la DQO recalcitrante que queda en el efluente. Para el desarrollo de una prueba de biodegradabilidad, es importante considerar diversos factores relacionados con la composición del agua a tratar, composición de los lodos y las condiciones bajo las cuales se lleva a cabo la prueba. La digestión anaerobia de aguas residuales industriales es comúnmente usada en todo el mundo, ofrece significativas ventajas para el tratamiento de efluentes altamente cargados. Los sistemas anaerobios de tratamiento de aguas residuales industriales incluyen tecnologías con biopelículas, estos sistemas de tratamiento anaerobio con biopelícula son una tecnología bien establecida para el tratamiento de efluentes industriales. El Reactor de Lecho Fluidizado Inverso Anaerobio (LFI) ha sido diseñado para el tratamiento de aguas residuales de alta carga, teniendo como ventajas el empleo de un soporte que proporciona una gran superficie y un bajo requerimiento de energía para la fluidización del lecho. En el presente trabajo, se lleva a cabo el análisis de un proceso de producción de etanol, identificando a los efluentes que se generan en el mismo. Se encuentra que el efluente final está compuesto principalmente por las vinazas provenientes del proceso de destilación. En la caracterización de las vinazas provenientes del proceso de producción de etanol a partir de melaza de azúcar de caña, se encontraron valores promedio de DQO de 193.35 gDQO/L, para los sólidos totales 109.78 gST/L y pH de 4.64. Así mismo, en esta investigación se llevó a cabo una prueba de biodegradabilidad anaerobia, aplicada a la vinaza proveniente de la producción de etanol. En la caracterización de los lodos empleados en el ensayo se obtiene una Actividad Metanogénica Especifica de 0.14 g DQO/gSSV.d. El porcentaje de remoción de DQO de la vinaza fue de 62.7%, obteniéndose una k igual a 0.031 h-1 y una taza de consumo de sustrato de 1.26 gDQO/d. El rendimiento de metano fue de 0.19 LCH4/g DQOremovida y el porcentaje de biodegradabilidad de 54.1%. El presente trabajo también evalúa el desempeño de un LFI, empleando Extendospher® como soporte y tratando efluentes provenientes de la producción de etanol. El reactor se arrancó en batch y posteriormente se operó en continuo a diferentes Cargas Orgánicas Volumétricas de 0.5, 1.0, 3.3, 6.8 y 10.4 g DQO/L.d. Además, se evaluaron diferentes Tiempos de Residencia Hidráulica de 10, 5 y 1 días. El sistema alcanzó las siguientes eficiencias promedio de remoción de DQO: 81% para la operación en batch; 58, 67, 59 y 50 % para las cargas de 0.5, 1.0, 3.3, 6.8 g DQO/L.d respectivamente. Para la carga de 10.4 g DQO/L.d, la eficiencia promedio de remoción de DQO fue 38%, en esta condición el reactor presentó inestabilidad y disminución del rendimiento de metano. La generación de metano inició hasta los 110 días de operación del reactor a una carga de 1.0 g DQO/L.d. El sistema alcanzó un rendimiento de metano desde 0.15 hasta 0.34 LCH4/g DQO. Durante la operación del reactor a una carga constante de 6.4 g DQO/L.d, y un TRH de 1 día, se alcanzó una eficiencia promedio de remoción de DQO de 52%. In the state of Veracruz, to the south of Mexico, there are located companies dedicated to the production of ethanol from molasses of cane sugar. The smallest, have a average production of 20,000 L ethanol/day. The effluent of production of ethanol include water of condensers, water originated from the cleanliness of tanks of fermentation and vinasses, the above mentioned are more effluent pollutants in the distilleries, for the poor organic matter degradability. The vinasses are generated in high volumes, producing from 12 to 15 L of vinasses per every liter of distilled ethanol. These effluent are characterized by its high temperature, pH acid and a high concentration of DQO as well as high concentration of TS. The determination of the anaerobic degradability of a waste water, it allows to estimate the fraction of DQO that can be transformed potentially into methane and the recalcitrant DQO that stays in the effluent. For the development of degradability test, it is important to consider factors related to the composition of the water to be treated, composition of the sludge and the conditions under which the test is carried out. The anaerobic digestion of industrial wastes water is used commonly in the whole world, it offers significant advantages for the treatment of effluent highly loaded. The anaerobic treatment of industrial wastes water include technologies with biofilms, this anaerobic treatment whit biofilms systems, is a well-established technology for treatment of industrial effluents. The Anaerobic Inverse Fluidized Bed Reactor (IFBR) has been developed to provide biological treatment of high strength organic wastewater for their large specific surface and their low energy requirements for fluidization. In this work, there is carried out the analysis of a process of production of ethanol, identifying the effluent ones that are generated in the process. One determined that the effluent end is composed principally by the vinasses originated from the process of distillation. In the characterization of the vinasses originated from the process of production of ethanol from cane sugar molasses, there were average values of DQO of 193.35 gDQO/L, average values of solid of 109.78 gST/L and pH of 4.64. In this investigation there was carried out a anaerobic degradability test of the vinasses generated in the production of ethanol. In the characterization of the sludge used in the essay, the specific methanogenic activity (SMA) was 0.14 gDQO/gSSV.d. The average removal of DQO of the vinasses was 62.7 %, k equal to 0.031 h-1 was obtained one and a rate of removal substrate of 1.26 gDQO/d. The methane yield was 0.19 LCH4/gDQO removed and the anaerobic biodegradability was a 54.1 %. This study describes the performance of IFBR with Extendospher®, for the treatment of vinasses. The start-up was made in batch, increasing gradually the Organic Load Rate (OLR): 0.5, 1.0, 3.3, 6.8 and 10.4 g COD/L.d. Different Hydraulic Retention Times (HRT) were evaluated: 10, 5 and 1 days. During the operation in batch, the COD removal obtained was of 81 %, and for OLR of 0.5, 1.0, 3.3, 6.8 g COD/L.d the removal obtained was 58, 67, 59 and 50 % respectively. For a maximum OLR of 10.4 g COD/L.d, the COD removal was 38 %, and the system presented instability and decrease of the yield methane. The methane production initiated after 110 days of the start-up of the IFBR, to organic load rate of 1.0 g COD/L.d. The system reached values in the methane yield from 0.15 up to 0.34 LCH4/g CODremoved, for the different organic load rates. During the operation to a constant OLR of 6.4 g COD/L.d, and a HRT of 1 day, the Anaerobic Inverse Fluidized Bed Reactor reached a maximum efficiency of removal of 52 %.

Rat heart: A site of oxytocin production and action

We report here that the rat heart is a site of oxytocin (OT) synthesis and release. Oxytocin was detected in all four chambers of the heart. The highest OT concentration was in the right atrium (2128 ± 114 pg/mg protein), which was 19-fold higher than in rat uterus but 3.3-fold lower than in the hypothalamus. OT concentrations were significantly greater in the right and left atria than in the corresponding ventricles. Furthermore, OT was released into the effluent of isolated, perfused rat heart (34.5 ± 4.7 pg/min) and into the medium of cultured atrial myocytes. Reverse-phase HPLC purification of the heart extracts and heart perfusates revealed a main peak identical with the retention time of synthetic OT. Southern blots of reverse transcription–PCR products from rat heart revealed gene expression of specific OT mRNA. OT immunostaining likewise was found in atrial myocytes and fibroblasts, and the intensity of positive stains from OT receptors paralleled the atrial natriuretic peptide stores. Our findings suggest that heart OT is structurally identical, and therefore derived from, the same gene as the OT that is primarily found in the hypothalamus. Thus, the heart synthesizes and processes a biologically active form of OT. The presence of OT and OT receptor in all of the heart’s chambers suggests an autocrine and/or paracrine role for the peptide. Our finding of abundant OT receptor in atrial myocytes supports our hypothesis that OT, directly and/or via atrial natriuretic peptide release, can regulate the force of cardiac contraction.

Negative pH, efflorescent mineralogy, and consequences for environmental restoration at the Iron Mountain Superfund site, California

The Richmond Mine of the Iron Mountain copper deposit contains some of the most acid mine waters ever reported. Values of pH have been measured as low as −3.6, combined metal concentrations as high as 200 g/liter, and sulfate concentrations as high as 760 g/liter. Copious quantities of soluble metal sulfate salts such as melanterite, chalcanthite, coquimbite, rhomboclase, voltaite, copiapite, and halotrichite have been identified, and some of these are forming from negative-pH mine waters. Geochemical calculations show that, under a mine-plugging remediation scenario, these salts would dissolve and the resultant 600,000-m3 mine pool would have a pH of 1 or less and contain several grams of dissolved metals per liter, much like the current portal effluent water. In the absence of plugging or other at-source control, current weathering rates indicate that the portal effluent will continue for approximately 3,000 years. Other remedial actions have greatly reduced metal loads into downstream drainages and the Sacramento River, primarily by capturing the major acidic discharges and routing them to a lime neutralization plant. Incorporation of geochemical modeling and mineralogical expertise into the decision-making process for remediation can save time, save money, and reduce the likelihood of deleterious consequences.

Autocrine signaling through ATP release represents a novel mechanism for cell volume regulation.

Recovery of cell volume in response to osmotic stress is mediated in part by increases in the Cl- permeability of the plasma membrane. These studies evaluate the hypothesis that ATP release and autocrine stimulation of purinergic (P2) receptors couple increases in cell volume to opening of Cl- channels. In HTC rat hepatoma cells, swelling induced by hypotonic exposure increased membrane Cl- current density to 44.8 +/- 7.1 pA/pF at -80 mV. Both the rate of volume recovery and the increase in Cl- permeability were inhibited in the presence of the ATP hydrolase apyrase (3 units/ml) or by exposure to the P2 receptor blockers suramin and Reactive Blue 2 (10-100 microM). Cell swelling also stimulated release of ATP. Hypotonic exposure increased the concentration of ATP in the effluent of perfused cells by 170 +/- 36 nM in the presence of a nucleotidase inhibitor (P < 0.01). In whole-cell recordings with ATP as the charge carrier, cell swelling increased membrane current density approximately 30-fold to 16.5 +/- 10.4 pA/pF. These findings indicate that increases in cell volume lead to efflux of ATP through opening of a conductive pathway consistent with a channel, and that extracellular ATP is required for recovery from swelling. ATP may function as an autocrine factor that couples increases in cell volume to opening of Cl- channels through stimulation of P2 receptors.

Flotação por ar dissolvido aplicado à separação de microalgas cultivadas em fotobiorreator, alimentado com vinhaça pré-tratada físico-quimicamente, com vistas à exploração de seu potencial bioenergético

Apesar de ser considerado um combustível sustentável, o etanol, produzido a partir da cana de açúcar, deixa um passivo de grandes proporções durante seu processo produtivo, a vinhaça, que vem sendo depositada nas próprias lavouras de cana de açúcar. É gerada na proporção de 12 litros para cada litro de etanol produzido em média, sendo rica em diversos nutrientes, os quais podem ser aproveitados para diversos fins como, por exemplo, meio de cultivo para microalgas. A presente pesquisa avaliou em uma primeira etapa a clarificação da vinhaça por um processo de coagulação com auxílio de um polímero catiônico, seguida de uma etapa de microfiltração tangencial em filtro de fibras ocas, o que permitiu uma redução superior a 77% para a cor aparente, de 99% para a turbidez e de 20% para a DQO, facilitando a utilização deste efluente para o cultivo de microalgas. Numa segunda etapa, foi avaliado o cultivo da microalga Chlorella vulgaris, em escala de bancada e operação em batelada, em meio preparado a partir da diluição da vinhaça em água de poço profundo, obtendo um aumento na biomassa produzida, determinado em termos de clorofila-a, em concentrações de vinhaça inferiores a 7,5% utilizando inóculo da ordem de 106 indivíduos. Tais dados permitiram a realização de ensaios de cultivo em escala contínua, com fotobiorreatores em escala piloto, gerando assim a biomassa utilizada nas próximas fases do estudo, que avaliaram a separação da biomassa gerada pelo processo de flotação por ar dissolvido. Os ensaios inicialmente realizados em escala de bancada e operados em batelada permitiram identificar as condições ótimas de operação, as quais foram então avaliadas em um flotador operando em fluxo contínuo. Tal flotador permitiu a obtenção de um lodo com teor de sólidos superior a 2%, o qual foi submetido à um processo final de desaguamento por centrifugação. Os ensaios de desaguamento, permitiram verificar que a utilização do mesmo polímero utilizado na etapa de clarificação permite a obtenção de um lodo mais estável, quando comparado com a não utilização de produto químico, na dosagem de polímero catiônico de 6 g.kg-1. A conclusão deste trabalho permitiu verificar a possibilidade de utilização da vinhaça como meio de cultivo de microalgas, reduzindo assim um dos impactos causados pela produção de etanol. Além disso foi possível verificar o potencial da FAD, para o espessamento de biomassa produzido em fotobiorreatores.

Tratamento de esgoto sanitário em reator anaeróbio horizontal de leito fixo (RAHLF): escala piloto

Este trabalho apresenta as avaliações de desempenho, das demandas operacionais e dos fatores intervenientes no aumento da escala da unidade piloto do Reator anaeróbio Horizontal de Leito Fixo (RAHLF) no tratamento de esgoto sanitário após passagem por peneira com malha de 1 mm, durante dois anos de operação. O reator dispunha de volume total de 237,5 1, construídos com tubos comerciais de PVC de 14,5 cm de diâmetro (D), dispostos em cinco módulos horizontais em série de 2,88 m, perfazendo um comprimento total de (L) de 14,4 m e relação de total de L/D de 100. O suporte de imobilização de biomassa, espuma de poliuretano em matrizes cúbicas de 1 cm de aresta, mostrou-se adequado ao desenvolvimento do biofilme. Em partida, sem inoculação prévia, ocorreu a sua consolidação a partir de 70 dias, com predominância de morfologia semelhante a Methanosaeta sp. em relação a da Methanosarcina. Em torno de 90 dias com afluente de 350 mg/l de DQO, observe-se a melhor qualidade do efluente, com valor de 100 mg/l de DQO. Em longa operação ocorreu queda de rendimento e menor reprodutibilidade das previsões do projeto, atribuída aos constantes entupimentos e ineficácia das operações de limpeza, com o comprometimento de volume reacional verificados por estudos de hidrodinâmica. Da investigação das origens dos equipamentos observou-se tratar mais de um efeito local e qualitativamente relacionado à biomassa retida que propriamente quantitativo e extensivo ao longo de todo reator, com produção continuada de polímeros extracelulares, promovendo um efeito sinérgico com os predominantes organismos filamentosos e com os sólidos particulados retidos no leito. Diante das potencialidades desta configuração de reator apontam-se alternativas de mitigação dos entupimentos e o direcionamento dos estudos necessários para novo aumento de escala para o tratamento de esgoto sanitário.