Study on the Capacity Degradation of Bucket Foundation in Liquefied Sand Layer under Cyclic Loads

The capacity degradation of bucket foundation in liquefied sand layer under cyclic loads such as equivalent dynamic ice-induced loads is studied. A simplified numerical model of liquefied sand layer has been presented based on the dynamic centrifuge experiment results. The ice-induced dynamic loads are modeled as equivalent sine cyclic loads, the liquefaction degree in different position of sand layer and effects of main factors are investigated. Subsequently, the sand resistance is represented by uncoupled, non-linear sand springs which describe the sub-failure behavior of the local sand resistance as well as the peak capacity of bucket foundation under some failure criterion. The capacity of bucket foundation is determined in liquefied sand layer and the rule of capacity degradation is analyzed. The capacity degradation in liquefied sand layer is analyzed comparing with that in non-liquefied sand layer. The results show that the liquefaction degree is 0.9 at the top and is only 0.06 at the bottom of liquefied sand layer. The numerical results are agreement well with the centrifugal experimental results. The value of the degradation of bucket capacity is 12% in numerical simulating whereas it is 17% in centrifugal experiments.

Numerical Simulation of Liquefaction Deformation of Sand Layer around Bucket Foundations under Dynamic Loadings

Bucket Foundations under Dynamic Loadings The liquefaction deformation of sand layer around a bucket foundation is simulated under equivalent dynamic ice-induced loadings. A simplified numerical model is presented by taking the bucket-soil interaction into consideration. The development of vertical and horizontal liquefaction deformations are computed under equivalent dynamic ice-induced loadings. Firstly, the numerical model and results are proved to be reliable by comparing them with the centrifuge testing results. Secondly, the factors and the development characteristics of liquefaction deformation are analyzed. Finally, the following numerical simulation results are obtained: the liquefaction deformation of sand layer increases with the increase of loading amplitude and with the decrease of loading frequency and sand skeleton’s strength. The maximum vertical deformation is located on the sand layer surface and 1/4 times of the bucket’s height apart from the bucket’s side wall (loading boundary). The maximum horizontal deformation occurs at the loading boundary. When the dynamic loadings is applied for more than 5 hours, the vertical deformation on the sand layer surface reaches 3 times that at the bottom, and the horizontal deformation at 2.0 times of the bucket height apart from the loading boundary is 3.3% of which on the loading boundary.

The effect of traditional handling, processing and storage methods on the quality of dried fish in small scale fisheries in Nigeria

Most of the fish marketed throughout Nigeria are in either smoked or dried form. The technological requirement for other forms of preservation like chilling and freezing cannot be afforded by the small scale fisher folk. Considerable quantities of fish processed for distant consumer markets are lost at handling, processing, storage and marketing stages. Significant losses occur through infestation by mites, insects, fungal infestation and fragmentation during transportation. This paper attempts to describe the effect of these losses on fish quality and suggests methods of protecting fish from agents of deterioration

Deepwater shorelines

Research has proven that Shoreline Erosion is caused by excess water contained within the shore face. This Research presents an opportunity to control erosion by managing the near shore water table. Our Research on Bogue Banks North Carolina suggests that our buildings and other impervious surfaces collect and concentrate water from storm rain runoff into the surface water table and within the critical beach front water exit point. Presently our Potable Fresh Water is supplied from deep wells located beneath an impervious layer of Marl. After our use, the Waste water is drained into the Surface Aquifer, the combined waste and storm rain water raises the Surface Aquifer water table and produces Erosion. The Deep Aquifers presently supplying our Potable Water have an unknown recharge rate, with increasing reports of Salt Water intrusion. We believe our Vital Fresh water supply system should be modified to supply Reverse Osmosis treatment plants from shallow wells. This will lower the Surface Water Table. These Shallow wells, either horizontal or vertical, might be located within the beach front, adjacent to high erosion risk properties. Beach Drains and Reverse Osmosis Water systems are new and proven technologies. By combining these technologies we can reduce or reverse Shore Erosion, ensure a safe Potable Water supply, reduce requirements for periodic beach nourishment, reduce taxes and protect our property well into the Future. (PDF contains 5 pages)

Liquid silicate equation of state : using shock waves to understand the properties of the deep Earth

The equations of state (EOS) of several geologically important silicate liquids have been constrained via preheated shock wave techniques. Results on molten Fe₂SiO₄ (fayalite), Mg₂SiO₄ (forsterite), CaFeSi₂O₆ (hedenbergite), an equimolar mixture of CaAl₂Si₂O₈-CaFeSi₂O₆ (anorthite-hedenbergite), and an equimolar mixture of CaAl₂Si₂O₈-CaFeSi₂O₆-CaMgSi₂O₆(anorthite-hedenbergite-diopside) are presented. This work represents the first ever direct EOS measurements of an iron-bearing liquid or of a forsterite liquid at pressures relevant to the deep Earth (> 135 GPa). Additionally, revised EOS for molten CaMgSi₂O₆ (diopside), CaAl₂Si₂O₈ (anorthite), and MgSiO₃ (enstatite), which were previously determined by shock wave methods, are also presented.

The liquid EOS are incorporated into a model, which employs linear mixing of volumes to determine the density of compositionally intermediate liquids in the CaO-MgO-Al₂O₃-SiO₂-FeO major element space. Liquid volumes are calculated for temperature and pressure conditions that are currently present at the core-mantle boundary or that may have occurred during differentiation of a fully molten mantle magma ocean.

The most significant implications of our results include: (1) a magma ocean of either chondrite or peridotite composition is less dense than its first crystallizing solid, which is not conducive to the formation of a basal mantle magma ocean, (2) the ambient mantle cannot produce a partial melt and an equilibrium residue sufficiently dense to form an ultralow velocity zone mush, and (3) due to the compositional dependence of Fe2+ coordination, there is a threshold of Fe concentration (molar X_Fe ≤ 0.06) permitted in a liquid for which its density can still be approximated by linear mixing of end-member volumes.

Effects of extracts of dried seeds of Toloache, Datura innoxia as anaesthesia on the African catfish Clarias gariepinus fingerlings

The effects of crude extract, pure extract, aqueous, fraction of pure and lipid fraction of pure extract of dried seeds of toloache. Datura innoxia as anaesthesia on the African catfish. Clarias gariepinus fingerlings were studied. The fish were exposed to various doses of the extract in aquaria tanks and the time taken for each fish to reach anaesthesia was recorded. The fish were anaesthetized up to 3.00g/l fingerlings reached anaesthesia is significantly (P<0.05) shorter time (1.004 minutes at 0.05gl) in pure unseparated extract than in crude extract (58.50 minutes at 3.00g/l concentrated). The time to reach anaesthesia decreased with an increase in concentration of the seed extract. Out the two fractions the lipid fraction had significantly (P>0.05) better anaesthetic on the fish. The control produced no observable anaesthetic effect on the fish within three hours. This suggests that the anaesthetizing active ingredent resided in the lipid fraction. All fish recovered from anaesthesia, swam and fed actively and no mortality was observed throughout the exposure period and thereafter. It is therefore recommended for use on C. gariepinus fingerlings

Structure of the earth's core and lowermost mantle from seismic PKP waves

This thesis addresses the fine structure, both radial and lateral, of compressional wave velocity and attenuation of the Earth's core and the lowermost mantle using waveforms, differential travel times and amplitudes of PKP waves, which penetrate the Earth's core.

The structure near the inner core boundary (ICB) is studied by analyzing waveforms of a regional sample. The waveform modeling approach is demonstrated to be an effective tool for constrainning the ICB structure. The best model features a sharp velocity jump of 0.78km/s at the ICB and a low velocity gradient at the lowermost outer core (indicating possible inhomogeneity) and high attenuation at the top of the inner core.

A spherically symmetric P-wave model of the core, is proposed from PKP differential times, waveforms and amplitudes. The ICB remains sharp with a velocity jump of 0. 78km/ s. A very low velocity gradient at the base of the fluid core is demonstrated to be a robust feature, indicating inhomogeneity is practically inevitable. The model also indicates that the attenuation in the inner core decreases with depth. The velocity at D" is smaller than PREM.

The inner core is confirmed to be very anisotropic, possessing a cylindrical symmetry around the Earth spin axis with the N-S direction 3% faster than the E-W direction. All of the N-S rays through the inner core were found to be faster than the E-W rays by 1.5 to 3.5s. Exhaustive data selection and efforts in insolating contributions from the region above ensure that this is an inner core feature.

The anisotropy at the very top of the inner core is found to be distinctly different from the deeper part. The top 60km of the inner core is not anisotropic. From 60km to 150km, there appears to be a transition from isotropy to anisotropy.

PKP differential travel times are used to study the P velocity structure in D". Systematic regional variations of up to 2s in AB-DF times were observed, attributed primarily to heterogeneities in the lower 500km of the mantle. However, direct comparisons with tomographic models are not successful.

Slender-body hypervelocity boundary-layer instability

With novel application of optical techniques, the slender-body hypervelocity boundary-layer instability is characterized in the previously unexplored regime where thermo-chemical effects are important. Narrowband disturbances (500-3000~kHz) are measured in boundary layers with edge velocities of up to 5~km/s at two points along the generator of a 5 degree half angle cone. Experimental amplification factor spectra are presented. Linear stability and PSE analysis is performed, with fair prediction of the frequency content of the disturbances; however, the analysis over-predicts the amplification of disturbances. The results of this work have two key implications: 1) the acoustic instability is present and may be studied in a large-scale hypervelocity reflected-shock tunnel, and 2) the new data set provides a new basis on which the instability can be studied.

Earth-abundant materials for solar hydrogen generation

A critical challenge for the 21st century is shifting from the predominant use of fossil fuels to renewables for energy. Among many options, sunlight is the only single renewable resource with sufficient abundance to replace most or all of our current fossil energy use. However, existing photovoltaic and solar thermal technologies cannot be scaled infinitely due to the temporal and geographic intermittency of sunlight. Therefore efficient and inexpensive methods for storage of solar energy in a dense medium are needed in order to greatly increase utilization of the sun as a primary resource. For this purpose we have proposed an artificial photosynthetic system consisting of semiconductors, electrocatalysts, and polymer membranes to carry out photoelectrochemical water splitting as a method for solar fuel generation.

This dissertation describes efforts over the last five years to develop critical semiconductor and catalyst components for efficient and scalable photoelectrochemical hydrogen evolution, one of the half reactions for water splitting. We identified and developed Ni–Mo alloy and Ni₂P nanoparticles as promising earth-abundant electrocatalysts for hydrogen evolution. We thoroughly characterized Ni–Mo alloys alongside Ni and Pt catalysts deposited onto planar and structured Si light absorbers for solar hydrogen generation. We sought to address several key challenges that emerged in the use of non-noble catalysts for solar fuels generation, resulting in the synthesis and characterization of Ni–Mo nanopowder for use in a new photocathode device architecture. To address the mismatch in stability between non-noble metal alloys and Si absorbers, we also synthesized and characterized p-type WSe₂ as a candidate light absorber alternative to Si that is stable under acidic and alkaline conditions.

Identification of thermally-tagged coherent structures in the zero pressure gradient turbulent boundary layer

A zero pressure gradient boundary layer over a flat plate is subjected to step changes in thermal condition at the wall, causing the formation of internal, heated layers. The resulting temperature fluctuations and their corresponding density variations are associated with turbulent coherent structures. Aero-optical distortion occurs when light passes through the boundary layer, encountering the changing index of refraction resulting from the density variations. Instantaneous measurements of streamwise velocity, temperature and the optical deflection angle experienced by a laser traversing the boundary layer are made using hot and cold wires and a Malley probe, respectively. Correlations of the deflection angle with the temperature and velocity records suggest that the dominant contribution to the deflection angle comes from thermally-tagged structures in the outer boundary layer with a convective velocity of approximately 0.8U∞. An examination of instantaneous temperature and velocity and their temporal gradients conditionally averaged around significant optical deflections shows behavior consistent with the passage of a heated vortex. Strong deflections are associated with strong negative temperature gradients, and strong positive velocity gradients where the sign of the streamwise velocity fluctuation changes. The power density spectrum of the optical deflections reveals associated structure size to be on the order of the boundary layer thickness. A comparison to the temperature and velocity spectra suggests that the responsible structures are smaller vortices in the outer boundary layer as opposed to larger scale motions. Notable differences between the power density spectra of the optical deflections and the temperature remain unresolved due to the low frequency response of the cold wire.

Seismic reflection experiments imaging the physical nature of crustal structures in southern California

Seismic reflection methods have been extensively used to probe the Earth's crust and suggest the nature of its formative processes. The analysis of multi-offset seismic reflection data extends the technique from a reconnaissance method to a powerful scientific tool that can be applied to test specific hypotheses. The treatment of reflections at multiple offsets becomes tractable if the assumptions of high-frequency rays are valid for the problem being considered. Their validity can be tested by applying the methods of analysis to full wave synthetics.

Three studies illustrate the application of these principles to investigations of the nature of the crust in southern California. A survey shot by the COCORP consortium in 1977 across the San Andreas fault near Parkfield revealed events in the record sections whose arrival time decreased with offset. The reflectors generating these events are imaged using a multi-offset three-dimensional Kirchhoff migration. Migrations of full wave acoustic synthetics having the same limitations in geometric coverage as the field survey demonstrate the utility of this back projection process for imaging. The migrated depth sections show the locations of the major physical boundaries of the San Andreas fault zone. The zone is bounded on the southwest by a near-vertical fault juxtaposing a Tertiary sedimentary section against uplifted crystalline rocks of the fault zone block. On the northeast, the fault zone is bounded by a fault dipping into the San Andreas, which includes slices of serpentinized ultramafics, intersecting it at 3 km depth. These interpretations can be made despite complications introduced by lateral heterogeneities.

In 1985 the Calcrust consortium designed a survey in the eastern Mojave desert to image structures in both the shallow and the deep crust. Preliminary field experiments showed that the major geophysical acquisition problem to be solved was the poor penetration of seismic energy through a low-velocity surface layer. Its effects could be mitigated through special acquisition and processing techniques. Data obtained from industry showed that quality data could be obtained from areas having a deeper, older sedimentary cover, causing a re-definition of the geologic objectives. Long offset stationary arrays were designed to provide reversed, wider angle coverage of the deep crust over parts of the survey. The preliminary field tests and constant monitoring of data quality and parameter adjustment allowed 108 km of excellent crustal data to be obtained.

This dataset, along with two others from the central and western Mojave, was used to constrain rock properties and the physical condition of the crust. The multi-offset analysis proceeded in two steps. First, an increase in reflection peak frequency with offset is indicative of a thinly layered reflector. The thickness and velocity contrast of the layering can be calculated from the spectral dispersion, to discriminate between structures resulting from broad scale or local effects. Second, the amplitude effects at different offsets of P-P scattering from weak elastic heterogeneities indicate whether the signs of the changes in density, rigidity, and Lame's parameter at the reflector agree or are opposed. The effects of reflection generation and propagation in a heterogeneous, anisotropic crust were contained by the design of the experiment and the simplicity of the observed amplitude and frequency trends. Multi-offset spectra and amplitude trend stacks of the three Mojave Desert datasets suggest that the most reflective structures in the middle crust are strong Poisson's ratio (σ) contrasts. Porous zones or the juxtaposition of units of mutually distant origin are indicated. Heterogeneities in σ increase towards the top of a basal crustal zone at ~22 km depth. The transition to the basal zone and to the mantle include increases in σ. The Moho itself includes ~400 m layering having a velocity higher than that of the uppermost mantle. The Moho maintains the same configuration across the Mojave despite 5 km of crustal thinning near the Colorado River. This indicates that Miocene extension there either thinned just the basal zone, or that the basal zone developed regionally after the extensional event.

Atom localization in a four-level alkaline earth atomic system

We propose an atom localization scheme for a four-level alkaline earth atom via a classical standing-wave field, and give the analytical expressions of the localization peak positions as well as the widths versus the parameters of the optical fields. We show that the probability of finding the atom at a particular position can be increased from 1/4 to 1/3 or 1/2 by adjusting the detuning of the probe field and the Rabi frequencies of the optical fields. Furthermore, the localization precision can be dramatically enhanced by increasing the intensity of the standing-wave field or decreasing the detuning of the probe field. The analytical results are quite accordant to the numerical solutions.