Six-Day System Test and Component test and System Simulation for Combitanks with Internal heat Exchangers

An international standard, ISO/DP 9459-4 has been proposed to establish a uniform standard of quality for small, factory-made solar heating systerns. In this proposal, system components are tested separatelyand total system performance is calculated using system simulations based on component model parameter values validated using the results from the component tests. Another approach is to test the whole system in operation under representative conditions, where the results can be used as a measure of the general system performance. The advantage of system testing of this form is that it is not dependent on simulations and the possible inaccuracies of the models. Its disadvantage is that it is restricted to the boundary conditions for the test. Component testing and system simulation is flexible, but requires an accurate and reliable simulation model.The heat store is a key component conceming system performance. Thus, this work focuses on the storage system consisting store, electrical auxiliary heater, heat exchangers and tempering valve. Four different storage system configurations with a volume of 750 litre were tested in an indoor system test using a six -day test sequence. A store component test and system simulation was carried out on one of the four configurations, applying the proposed standard for stores, ISO/DP 9459-4A. Three newly developed test sequences for intemalload side heat exchangers, not in the proposed ISO standard, were also carried out. The MULTIPORT store model was used for this work. This paper discusses the results of the indoor system test, the store component test, the validation of the store model parameter values and the system simulations.

Simulation of Photovoltaic Panel Production as Complement to Ground Source Heat Pump System

This master thesis presents a new technological combination of two environmentally friendly sources of energy in order to provide DHW, and space heating. Solar energy is used for space heating, and DHW production using PV modules which supply direct current directly to electrical heating elements inside a water storage tank. On the other hand a GSHP system as another source of renewable energy provides heat in the water storage tank of the system in order to provide DHW and space heating. These two sources of renewable energy have been combined in this case-study in order to obtain a more efficient system, which will reduce the amount of electricity consumed by the GSHP system.The key aim of this study is to make simulations, and calculations of the amount ofelectrical energy that can be expected to be produced by a certain amount of PV modules that are already assembled on a house in Vantaa, southern Finland. This energy is then intended to be used as a complement to produce hot water in the heating system of the house beside the original GSHP system. Thus the amount of electrical energy purchased from the grid should be reduced and the compressor in the GSHP would need fewer starts which would reduce the heating cost of the GSHP system for space heating and providing hot water.The produced energy by the PV arrays in three different circuits will be charged directly to three electrical heating elements in the water storage tank of the existing system to satisfy the demand of the heating elements. The excess energy can be used to heat the water in the water storage tank to some extent which leads to a reduction of electricity consumption by the different components of the GSHP system.To increase the efficiency of the existing hybrid system, optimization of different PV configurations have been accomplished, and the results are compared. Optimization of the arrays in southern and western walls shows a DC power increase of 298 kWh/year compared with the existing PV configurations. Comparing the results from the optimization of the arrays on the western roof if the intention is to feed AC power to the components of the GSHP system shows a yearly AC power production of 1,646 kWh.This is with the consideration of no overproduction by the PV modules during the summer months. This means the optimized PV systems will be able to cover a larger part of summer demand compared with the existing system.

Sociologin, hybriderna och den sociala verkligheten : exemplet kärnavfall

Sociology, hybrids and social reality: the case of nuclear waste The continuing technological transformation of nature means that sociology’s traditional vision of a sharp divide between nature and society is becoming ever harder to defend. Starting from Bruno Latour’s critique of modernity, and Nikolas Rose’s explorations of political power beyond the state, this article presents a framework for analysing the expanding wealth of hybrids of nature and society surrounding us today, and the problems of government they pose. These hybrids confront us with the need to rethink sociology’s conception of ‘the social’. With Latour’s help, the interplay of nature and society can be understood as subject to technical mediation, opening the way for studies of the varying arrangements through which different configurations of nature and society are produced. Rather than alternative social constructions of nature, what sociologists should be at pains to analyse and question are different programmes and strategies for bringing together natural and social forces in durable combinations. In the article, the geological disposal of nuclear waste serves as a useful example for exploring the fruitfulness of the analytical framework put forward. This complex undertaking constitutes just one component in a larger field of technoscientific endeavour that has irrevocably transformed nature while simultaneously re-making society. Addressing this case, we seek to reveal the promise of a sociology that does not bound ‘the social’ in advance, but rather makes the co-production of technology and society one of its most important objects of study.

Simulation study of cascade heat pump for solar combisystems

This paper focuses on the study of cascade heat pump systems in combination with solar thermal for the production of hot water and space heating in single family houses with relatively high heating demand. The system concept was developed by Ratiotherm GmbH and simulated with TRNSYS 17. The basic cascade system uses the heat pump and solar collectors in parallel operation while a further development is the inclusion of an intermediate store that enables the possibility of serial/parallel operation and the use of low temperature solar heat. Parametric studies in terms of compressor size, refrigerant pair and size of intermediate heat exchanger were carried out for the optimization of the basic system. The system configurations were simulated for the complete year and compared to a reference of a solar thermal system combined with an air source heat pump. The results show ~13% savings in electricity use for all three cascade systems compared to the reference. However, the complexity of the systems is different and thus higher capital costs are expected.

Review of the effectiveness of vehicle activated signs

This paper reviews the effectiveness of vehicle activated signs. Vehicle activated signs are being reportedly used in recent years to display dynamic information to road users on an individual basis in order to give a warning or inform about a specific event. Vehicle activated signs are triggered individually by vehicles when a certain criteria is met. An example of such criteria is to trigger a speed limit sign when the driver exceeds a pre-set threshold speed. The preset threshold is usually set to a constant value which is often equal, or relative, to the speed limit on a particular road segment. This review examines in detail the basis for the configuration of the existing sign types in previous studies and explores the relation between the configuration of the sign and their impact on driver behavior and sign efficiency. Most of previous studies showed that these signs have significant impact on driver behavior, traffic safety and traffic efficiency. In most cases the signs deployed have yielded reductions in mean speeds, in speed variation and in longer headways. However most experiments reported within the area were performed with the signs set to a certain static configuration within applicable conditions. Since some of the aforementioned factors are dynamic in nature, it is felt that the configurations of these signs were thus not carefully considered by previous researchers and there is no clear statement in the previous studies describing the relationship between the trigger value and its consequences under different conditions. Bearing in mind that different designs of vehicle activated signs can give a different impact under certain conditions of road, traffic and weather conditions the current work suggests that variable speed thresholds should be considered instead.

Model Configuration And Data Management In The Short-Term Water Information Forecasting Tools

The Short-term Water Information and Forecasting Tools (SWIFT) is a suite of tools for flood and short-term streamflow forecasting, consisting of a collection of hydrologic model components and utilities. Catchments are modeled using conceptual subareas and a node-link structure for channel routing. The tools comprise modules for calibration, model state updating, output error correction, ensemble runs and data assimilation. Given the combinatorial nature of the modelling experiments and the sub-daily time steps typically used for simulations, the volume of model configurations and time series data is substantial and its management is not trivial. SWIFT is currently used mostly for research purposes but has also been used operationally, with intersecting but significantly different requirements. Early versions of SWIFT used mostly ad-hoc text files handled via Fortran code, with limited use of netCDF for time series data. The configuration and data handling modules have since been redesigned. The model configuration now follows a design where the data model is decoupled from the on-disk persistence mechanism. For research purposes the preferred on-disk format is JSON, to leverage numerous software libraries in a variety of languages, while retaining the legacy option of custom tab-separated text formats when it is a preferred access arrangement for the researcher. By decoupling data model and data persistence, it is much easier to interchangeably use for instance relational databases to provide stricter provenance and audit trail capabilities in an operational flood forecasting context. For the time series data, given the volume and required throughput, text based formats are usually inadequate. A schema derived from CF conventions has been designed to efficiently handle time series for SWIFT.

Defeitos pontuais nos compostos intermetálicos ZrNi e Zr/sub 2/Ni estudados por dinâmica molecular

Empregamos a técnica de Dinâmica Molecular para estudar propriedades de defeitos pontuais nos compostos intermetálicos ZrNi e Zr2Ni. Descrevemos as configurações estáveis de defeitos e mecanismos de migração, assim como as energias envolvidas. Os potenciais interatômicos foram derivados do Embedded Atom Model. No intuito de levar em conta a variação de estequiometria causada pela presença de alguns tipos de defeitos em intermetálicos, apresentamos um método numérico que fornece a energia efetiva de formação de defeitos e aplicamos o método ao ZrNi e Zr2Ni. Os resultados mostraram que vacâncias são mais estáveis na sub—rede do Ni, com energia de formação de 0,83 e-0,61 eV em ZrNi e Zr2Ni, respectivamente. Vacâncias de Zr são instáveis em ambos compostos; elas decaem espontaneamente em pares anti—sítio e vacância de Ni. Configurações e energias de formação de intersticiais também foram calculadas e mostraram comportamentos similares. Em ZrNi, a migração de vacâncias ocorre preferencialmente nas direções [025] e [100], com as respectivas energias de migração 0,67 e 0,73 eV, e é um processo essencialmente bidimensional no plano (001). Em Zr,Ni, a migração de vacâncias é unidimensional, ocorrendo na direção [001], com energia de migração de 0,67 eV. Em ambos compostos a presença de defeitos de anti—sítio de Ni diminui a energia de migração da vacância de Ni em até 3 vezes e facilita a movimentação em três dimensões. Mecanismos de anel não são energeticamente eficientes em comparação com saltos diretos. As configurações estáveis de intersticiais em ambos compostos consistem em um átomo de Ni sobre o plano (001) entre dois vizinhos de Zr fora do plano. Intersticiais de Zr são instáveis e tendem a deslocar um átomo de Ni, ocupando seu sítio. Energias de deslocamento foram estudadas através de simulações de irradiação de ambos compostos. Durante o processo de colisão binária, um potencial universal ZBL foi usado para colisões a curta distância. Para distâncias intermediárias usamos um potencial de união arbitrário. Zr mostrou—se mais difícil de ser arrancado de seu sítio do que Ni. Encontramos valores de energia de deslocamento no intervalo de aproximadamente 29 eV até 546 eV. Alguns resultados experimentais são mostrados e apresentam boa concordância com os cálculos.

Beyond indifferent players: on the existence of prisoners dilemmas in games with amicable and adversarial preferences

Why don’t agents cooperate when they both stand to gain? This question ranks among the most fundamental in the social sciences. Explanations abound. Among the most compelling are various configurations of the prisoner’s dilemma (PD), or public goods problem. Payoffs in PD’s are specified in one of two ways: as primitive cardinal payoffs or as ordinal final utility. However, as final utility is objectively unobservable, only the primitive payoff games are ever observed. This paper explores mappings from primitive payoff to utility payoff games and demonstrates that though an observable game is a PD there are broad classes of utility functions for which there exists no associated utility PD. In particular we show that even small amounts of either altruism or enmity may disrupt the mapping from primitive payoff to utility PD. We then examine some implications of these results.

Relations between regulation, competition policy and consumer protection in telecommunications, electricity and water supply

The purpose of this article is to discuss the relations between regulation, competition policy and consumer protection these relations in three key sectors of Brazil’s infrastructure: telecommunications, electricity and water supply. A study of the literature points to two general principles. First, the need for consumer protection depends on the “degree of sovereignty” enjoyed by consumers, defined in terms of the cost of consumer organization, consumers’ ability to evaluate services, and the level of competition in each sector. Second, the less sovereignty consumers enjoy the more consumer protection institutions are involved with regulation agencies. The evidence for the Brazilian case apparently corroborates these points. In addition, it is important to stress that consumer complaints in regulated sectors seem to have increased more intensely than in others. The article is divided into three sections. Section 1 presents theoretical elements and aspects of the relations between regulation, competition policy and consumer protection evidenced by international experience. Section 2 analyzes the Brazilian experience and in particular the available statistics on consumer complaints about telecommunications, electricity and water supply, submitted to Fundação Procon-SP during the nineties. The last section points to possible configurations of the institutional relations between competition policy, regulation and consumer protection, showing how the existing configuration of these areas in the three infrastructure sectors discussed confirms that the theoretical framework proposed has reasonable predictive power.

Reuse-based test planning for core-based systems-on-chip

Electronic applications are currently developed under the reuse-based paradigm. This design methodology presents several advantages for the reduction of the design complexity, but brings new challenges for the test of the final circuit. The access to embedded cores, the integration of several test methods, and the optimization of the several cost factors are just a few of the several problems that need to be tackled during test planning. Within this context, this thesis proposes two test planning approaches that aim at reducing the test costs of a core-based system by means of hardware reuse and integration of the test planning into the design flow. The first approach considers systems whose cores are connected directly or through a functional bus. The test planning method consists of a comprehensive model that includes the definition of a multi-mode access mechanism inside the chip and a search algorithm for the exploration of the design space. The access mechanism model considers the reuse of functional connections as well as partial test buses, cores transparency, and other bypass modes. The test schedule is defined in conjunction with the access mechanism so that good trade-offs among the costs of pins, area, and test time can be sought. Furthermore, system power constraints are also considered. This expansion of concerns makes it possible an efficient, yet fine-grained search, in the huge design space of a reuse-based environment. Experimental results clearly show the variety of trade-offs that can be explored using the proposed model, and its effectiveness on optimizing the system test plan. Networks-on-chip are likely to become the main communication platform of systemson- chip. Thus, the second approach presented in this work proposes the reuse of the on-chip network for the test of the cores embedded into the systems that use this communication platform. A power-aware test scheduling algorithm aiming at exploiting the network characteristics to minimize the system test time is presented. The reuse strategy is evaluated considering a number of system configurations, such as different positions of the cores in the network, power consumption constraints and number of interfaces with the tester. Experimental results show that the parallelization capability of the network can be exploited to reduce the system test time, whereas area and pin overhead are strongly minimized. In this manuscript, the main problems of the test of core-based systems are firstly identified and the current solutions are discussed. The problems being tackled by this thesis are then listed and the test planning approaches are detailed. Both test planning techniques are validated for the recently released ITC’02 SoC Test Benchmarks, and further compared to other test planning methods of the literature. This comparison confirms the efficiency of the proposed methods.

Novas configurações organizacionais: pesquisa exploratória empírica sobre organizações locais

Esta pesquisa investiga a questão da evolução das configurações organizacionais. As mudanças ocorridas no ambiente competitivo brasileiro nos últimos anos levaram muitas empresas a buscar novos modelos de organização e gestão. Tal movimento pode representar uma superação, ou alternativamente uma evolução, do paradigma taylorista-fordista em direção a formatos mais orgânicos. Este projeto compreende uma pesquisa bibliográfica sobre o tema e uma pesquisa exploratória de campo, envolvendo organizações locais. São discutidos padrões genéricos de mudança e tendências, estabelecendo-se proposições a serem avaliadas em trabalho posterior.

O Conceito de postponement como estratégia de distribuição: um estudo de multi-casos no mercado brasileiro

Este trabalho discute a implementação da estratégia de postponement, um conceito que vem crescendo de importância nos últimos anos. Postponement é um conceito operacional que consiste em retardar a configuração final de produtos até que os pedidos dos consumidores sejam recebidos. Apesar da atratividade teórica e relevância do tema, pouco ainda se sabe sobre seu processo de implementação, especialmente no ambiente de negócio brasileiro. Este trabalho investigou em profundidade a implementação do postponement em cinco conceituadas empresas no Brasil procurando identificar os motivos que levaram seus respectivos executivos a adotarem tal estratégia, quais foram os agentes facilitadores e os obstáculos à implementação e, finalmente, até que ponto o postponement contribuiu para um aumento da competitividade.

Equilíbrio macroeconômico nos anos 80 e 90 - (Brasil, Argentina, Chile e México)

O objetivo desta pesquisa é o de apresentar um modelo que tenha condições de analisar as inter-relações entre macro e microeconomia, sem supor, de maneira apriorística, que todo o comportamento de variáveis macroeconômicas deva ter uma fundamentação microeconômica. Em tal análise se procurará mostrar como as variáveis macroeconômicas podem alterar a natureza e as reações dos agentes ao nível microeconômico e, ao mesmo tempo, chamar atenção para como as microvariáveis condicionam o ajustamento macroeconômico. Tal abordagem permite levar em consideração as configurações institucionais da economia, podendo constituir-se em um útil instrumento da análise dos processos de estabilização econômica.

Tratamento de efluente de curtume por contactores biológicos rotatórios com opção de pré-tratamento por reator acidogênico

Esta pesquisa teve por objetivo avaliar a performance de um sistema de tratamento baseado no processo de Contactores Biológicos Rotatórios (CBR), com a opção de prétratamento por Reator Acidogênico (RA), para o tratamento do efluente de um curtume que realiza as operações de recurtimento e acabamento. Os estudos experimentais foram desenvolvidos em escala de bancada, onde foram testadas duas configurações para a estação de tratamento. Na Configuração I o Reator Acidogênico precede o sistema de CBR, na Configuração II apenas um decantador precede os CBR. Para cada configuração foram testados três Tempos de Detenção Hidráulica (TDH) de 90, 45 e 22 horas no sistema de CBR correspondentes as Etapas 1, 2 e 3 respectivamente. Deste modo foi possível avaliar a influência do RA no desempenho dos CBR, sendo que o RA teria a função de promover a hidrólise e solubilização da matéria orgânica dificilmente degradável, facilitando a ação dos microrganismos aeróbios nos CBR. Foi avaliada a remoção de matéria orgânica nas três etapas das duas configurações estudadas, tendo como resultados eficiências (remoção de DQOt) de 60%, 61% e 63% para as etapas 1,2 e 3 respectivamente da Configuração I e 81%, 83% e 66% para as etapa 1, 2 e 3 da Configuração II. Também foram avaliadas as remoções de cromo além da nitrificação e denitrificação no sistema de tratamento. A comparação entre as duas Configurações estudadas ficou prejudicada devido a mudanças nas características do efluente do curtume que na Configuração II apresentou uma maior degradabilidade (maior relação DBO/DQO) que na Configuração I. Mesmo assim, foi obtida uma correlação entre os dados de carga de DQOsol aplicada e removida indicando que o Reator Acidogênico promoveu uma otimização no sistema de CBR. Assim foi possível avaliar as características operacionais e a proposição de modelo matemático referente ao desempenho de CBR tratando um efluente real de lenta degradação.