Spray visualisation and acoustic analysis in a gas-turbine type burner

This paper presents the characterisation of self-excited oscillations in a kerosene burner. The combustion instability exhibits two different modes and frequencies depending on the air flow rate. Experimental results reveal the influence of the spray to shift between these two modes. Pressure and heat release fluctuations have been measured simultaneously and the flame transfer function has been calculated from these measurements. The Mie scattering technique has been used to record spray fluctuations in reacting conditions with a high speed camera. Innovative image processing has enabled us to obtain fluctuations of the Mie scattered light from the spray as a temporal signal acquired simultaneously with pressure fluctuations. This has been used to determine a transfer function relating the image intensity and hence the spray fluctuations to changes in air velocity. This function has identified the different role the spray plays in the two modes of instability. At low air flow rates, the spray responds to an unsteady air flow rate and the time varying spray characteristics lead to unsteady combustion. At higher air flow rates, effective evaporation means that the spray dynamics are less important, leading to a different flame transfer function and frequency of self-excited oscillation. In conclusion, the combustion instabilities observed are closely related with the fluctuations of the spray motion and evaporation.

Anomalous n-type electrical behaviour of Pd-contacted CNTFET fabricated on small-diameter nanotube.

A Pd-contacted dopant-free CNTFET with small-diameter (0.57 nm) carbon nanotube showing an anomalous n-type electrical characteristic is reported for the first time. This observed behaviour is attributed to a carbon nanotube work function higher than (or close to) palladium as well as a large hole-to-electron effective mass ratio of approximately 2.5 predicted by hybridization in small-diameter nanotubes. A variation of the conduction type with temperature is also observed and is attributed to an increase of the palladium work function and decrease of the CNT work function with increasing temperature.

MDNR-NOAA trawl standardization study

Long-term living resource monitoring programs are commonly conducted globally to evaluate trends and impacts of environmental change and management actions. For example, the Woods Hole bottom trawl survey has been conducted since 1963 providing critical information on the biology and distribution of finfish and shellfish in the North Atlantic (Despres-Patango et al. 1988). Similarly in the Chesapeake Bay, the Maryland Department of Natural Resources (MDNR) Summer Blue Crab Trawl survey has been conducted continuously since 1977 providing management-relevant information on the abundance of this important commercial and recreational species. A key component of monitoring program design is standardization of methods over time to allow for a continuous, unbiased data set. However, complete standardization is not always possible where multiple vessels, captains, and crews are required to cover large geographic areas (Tyson et al. 2006). Of equal issue is technological advancement of gear which serves to increase capture efficiency or ease of use. Thus, to maintain consistency and facilitate interpretation of reported data in long-term datasets, it is imperative to understand and quantify the impacts of changes in gear and vessels on catch per unit of effort (CPUE). While vessel changes are inevitable due to ageing fleets and other factors, gear changes often reflect a decision to exploit technological advances. A prime example of this is the otter trawl, a common tool for fisheries monitoring and research worldwide. Historically, trawl nets were constructed of natural materials such as cotton and linen. However modern net construction consists of synthetic materials such as polyamide, polyester, polyethylene, and polypropylene (Nielson et. al. 1983). Over the past several decades, polyamide materials which will be referred to as nylon, has been a standard material used in otter trawl construction. These trawls are typically dipped into a latex coating for increased abrasion resistance, a process that is referred to as “green dipped.” More recently, polyethylene netting has become popular among living resource monitoring agencies. Polyethylene netting, commonly known as sapphire netting, consists of braided filaments that form a very durable material more resistant to abrasion than nylon. Additionally, sapphire netting allows for stronger knot strength during construction of the net further increasing the net’s durability and longevity. Also, sapphire absorbs less water with a specific gravity near 0.91 allowing the material to float as compared to nylon with specific gravity of 1.14 (Nielson et. al. 1983). This same property results in a light weight net which is more efficient in deployment, retrieval and fishing of the net, particularly when towing from small vessels. While there are many advantages to the sapphire netting, no comparative efficiency data is available for these two trawl net types. Traditional nylon netting has been used consistently for decades by the MDDNR to generate long term living resource data sets of great value. However, there is much interest in switching to the advanced materials. In addition, recent collaborative efforts between MDNR and NOAA’s Cooperative Oxford Laboratory (NOAA-COL) require using different vessels for trawling in support of joint projects. In order to continue collaborative programs, or change to more innovative netting materials, the influence of these changes must be demonstrated to be negligible or correction factors determined. Thus, the objective of this study was to examine the influence of trawl net type, vessel type, and their interaction on capture efficiency.

An ecological correction to marine reserves boundaries in the US Virgin Islands

Marine protected areas (MPAs) are important tools for management of marine ecosystems. While desired, ecological and biological criteria are not always feasible to consider when establishing protected areas. In 2001, the Virgin Islands Coral Reef National Monument (VICR) in St. John, US Virgin Islands was established by Executive Order. VICR boundaries were based on administrative determination of Territorial Sea boundaries and land ownership at the time of the Territorial Submerged Lands Act of 1974. VICR prohibits almost all fishing and other extractive uses. Surveys of habitat and fishes inside and outside of VICR were conducted in 2002-07. Based on these surveys, areas outside VICR had significantly more hard corals; greater habitat complexity; and greater richness, abundance and biomass of reef fishes than areas within VICR, further supporting results from 2002-2004 (Monaco et al., 2007). The administrative (political) process used to establish VICR did not allow a robust ecological characterization of the area to determine the boundaries of the MPA. Efforts are underway to increase amounts of complex reef habitat within VICR by swapping a part of VICR that has little coral reef habitat for a Territorially-owned area within VICR that contains a coral reef with higher coral cover.