Avaliação da aplicabilidade de correlações matemáticas e redes neurais na predição de parâmetros de especificação do diesel

Diesel fuel is one of leading petroleum products marketed in Brazil, and has its quality monitored by specialized laboratories linked to the National Agency of Petroleum, Natural Gas and Biofuels - ANP. The main trial evaluating physicochemical properties of diesel are listed in the resolutions ANP Nº 65 of December 9th, 2011 and Nº 45 of December 20th, 2012 that determine the specification limits for each parameter and methodologies of analysis that should be adopted. However the methods used although quite consolidated, require dedicated equipment with high cost of acquisition and maintenance, as well as technical expertise for completion of these trials. Studies for development of more rapid alternative methods and lower cost have been the focus of many researchers. In this same perspective, this work conducted an assessment of the applicability of existing specialized literature on mathematical equations and artificial neural networks (ANN) for the determination of parameters of specification diesel fuel. 162 samples of diesel with a maximum sulfur content of 50, 500 and 1800 ppm, which were analyzed in a specialized laboratory using ASTM methods recommended by the ANP, with a total of 810 trials were used for this study. Experimental results atmospheric distillation (ASTM D86), and density (ASTM D4052) of diesel samples were used as basic input variables to the equations evaluated. The RNAs were applied to predict the flash point, cetane number and sulfur content (S50, S500, S1800), in which were tested network architectures feed-forward backpropagation and generalized regression varying the parameters of the matrix input in order to determine the set of variables and the best type of network for the prediction of variables of interest. The results obtained by the equations and RNAs were compared with experimental results using the nonparametric Wilcoxon test and Student's t test, at a significance level of 5%, as well as the coefficient of determination and percentage error, an error which was obtained 27, 61% for the flash point using a specific equation. The cetane number was obtained by three equations, and both showed good correlation coefficients, especially equation based on aniline point, with the lowest error of 0,816%. ANNs for predicting the flash point and the index cetane showed quite superior results to those observed with the mathematical equations, respectively, with errors of 2,55% and 0,23%. Among the samples with different sulfur contents, the RNAs were better able to predict the S1800 with error of 1,557%. Generally, networks of the type feedforward proved superior to generalized regression.

Avaliação do desempenho da paligorsquita modificada e do carvão da pirólise do lodo de esgoto no processo de degradação fotocatalítica do fenol

The uncontrolled disposal of wastewaters containing phenolic compounds by the industry has caused irreversible damage to the environment. Because of this, it is now mandatory to develop new methods to treat these effluents before they are disposed of. One of the most promising and low cost approaches is the degradation of phenolic compounds via photocatalysis. This work, in particular, has as the main goal, the customization of a bench scale photoreactor and the preparation of catalysts via utilization of char originated from the fast pyrolysis of sewage sludge. The experiments were carried out at constant temperature (50°C) under oxygen (410, 515, 650 and 750 ml min-1). The reaction took place in the liquid phase (3.4 liters), where the catalyst concentration was 1g L-1 and the initial concentration of phenol was 500 mg L-1 and the reaction time was set to 3 hours. A 400 W lamp was adapted to the reactor. The flow of oxygen was optimized to 650 ml min-1. The pH of the liquid and the nature of the catalyst (acidified and calcined palygorskite, palygorskite impregnated with 3.8% Fe and the pyrolysis char) were investigated. The catalytic materials were characterized by XRD, XRF, and BET. In the process of photocatalytic degradation of phenol, the results showed that the pH has a significant influence on the phenol conversion, with best results for pH equal to 5.5. The phenol conversion ranged from 51.78% for the char sewage sludge to 58.02% (for palygorskite acidified calcined). Liquid samples analyzed by liquid chromatography and the following compounds were identified: hydroquinone, catechol and maleic acid. A mechanism of the reaction was proposed, whereas the phenol is transformed into the homogeneous phase and the others react on the catalyst surface. For the latter, the Langmuir-Hinshelwood model was applied, whose mass balances led to a system of differential equations and these were solved using numerical methods in order to get estimates for the kinetic and adsorption parameters. The model was adjusted satisfactorily to the experimental results. From the proposed mechanism and the operating conditions used in this study, the most favored step, regardless of the catalyst, was the acid group (originated from quinone compounds), being transformed into CO2 and water, whose rate constant k4 presented value of 0.578 mol L-1 min-1 for acidified calcined palygorskite, 0.472 mol L-1 min-1 for Fe2O3/palygorskite and 1.276 mol L-1 min-1 for the sludge to char, the latter being the best catalyst for mineralization of acid to CO2 and water. The quinones were adsorbed to the acidic sites of the calcined palygorskite and Fe2O3/palygorskite whose adsorption constants were similar (~ 4.45 L mol-1) and higher than that of the sewage sludge char (3.77 L mol-1).

Avaliação do desempenho da paligorsquita modificada e do carvão da pirólise do lodo de esgoto no processo de degradação fotocatalítica do fenol

The uncontrolled disposal of wastewaters containing phenolic compounds by the industry has caused irreversible damage to the environment. Because of this, it is now mandatory to develop new methods to treat these effluents before they are disposed of. One of the most promising and low cost approaches is the degradation of phenolic compounds via photocatalysis. This work, in particular, has as the main goal, the customization of a bench scale photoreactor and the preparation of catalysts via utilization of char originated from the fast pyrolysis of sewage sludge. The experiments were carried out at constant temperature (50°C) under oxygen (410, 515, 650 and 750 ml min-1). The reaction took place in the liquid phase (3.4 liters), where the catalyst concentration was 1g L-1 and the initial concentration of phenol was 500 mg L-1 and the reaction time was set to 3 hours. A 400 W lamp was adapted to the reactor. The flow of oxygen was optimized to 650 ml min-1. The pH of the liquid and the nature of the catalyst (acidified and calcined palygorskite, palygorskite impregnated with 3.8% Fe and the pyrolysis char) were investigated. The catalytic materials were characterized by XRD, XRF, and BET. In the process of photocatalytic degradation of phenol, the results showed that the pH has a significant influence on the phenol conversion, with best results for pH equal to 5.5. The phenol conversion ranged from 51.78% for the char sewage sludge to 58.02% (for palygorskite acidified calcined). Liquid samples analyzed by liquid chromatography and the following compounds were identified: hydroquinone, catechol and maleic acid. A mechanism of the reaction was proposed, whereas the phenol is transformed into the homogeneous phase and the others react on the catalyst surface. For the latter, the Langmuir-Hinshelwood model was applied, whose mass balances led to a system of differential equations and these were solved using numerical methods in order to get estimates for the kinetic and adsorption parameters. The model was adjusted satisfactorily to the experimental results. From the proposed mechanism and the operating conditions used in this study, the most favored step, regardless of the catalyst, was the acid group (originated from quinone compounds), being transformed into CO2 and water, whose rate constant k4 presented value of 0.578 mol L-1 min-1 for acidified calcined palygorskite, 0.472 mol L-1 min-1 for Fe2O3/palygorskite and 1.276 mol L-1 min-1 for the sludge to char, the latter being the best catalyst for mineralization of acid to CO2 and water. The quinones were adsorbed to the acidic sites of the calcined palygorskite and Fe2O3/palygorskite whose adsorption constants were similar (~ 4.45 L mol-1) and higher than that of the sewage sludge char (3.77 L mol-1).

Caracterização do material particulado e avaliação do risco ocupacional e mecanismos moleculares associados à queima artesanal da castanha de caju

Brazil is among the largest cashew nut producers of the world. However, the roasting process is still carried out artisanally, especially in the Brazilian semiarid region. In face of this occupational problem, the aim of this study was to perform a physical-chemical characterization of the particulate matter (PM) emitted by the roasting of cashew nuts, as well as to determine the occupational risk and molecular mechanisms associated. The most evident PM characteristics were the prevalence of fine particles, typical biomass burning morphologies such as tar ball and the presence of the elements K, Cl, S, Ca and Fe. In addition, atmospheric modeling analyses suggest that these particles can reach neighboring regions of the emission source. Polycyclic aromatic hydrocarbons (PAHs) with carcinogenic potential, such as benzo[a]pyrene, dibenz[a,h]anthracene, benzo[a]anthracene, benzo[b]fluoranthene, chrysene, benzo[k]fluoranthene, indeno[1,2,3-c,d]pyrene and benzo[j]fluoranthene were the most abundant PAHs found in the two air monitoring campaigns. Among the identified oxy-PAH the benzanthrone (7H-benz[d,e]anthracen-7-one) had the highest concentration and the evaluation of lifetime cancer risk showed an increase of 12 to 37 cases of cancer for every 10,000 exposed people. Chemical analysis of roasted cashew nuts identified the PAHs: phenanthrene, benzo[g,h,i]perylene, pyrene and benzo[a]pyrene, besides the 3-pentadecilfenol allergen (urushiol analogue) as prevalent. Occupational exposure to PAHs was confirmed by the increase of urinary 1-hydroxypyrene levels and genotoxic effects were evidenced by the increase on micronuclei and nuclear bud frequency in exfoliated buccal mucosa cells among the exposed workers. Other biomarkers of effects such as karyorrhexis, pyknotic, karyolytic, condensed chromatin and binucleated cells also have their frequencies increased when compared to an unexposed control group. The investigation of the molecular mechanisms associated with the PM organic extract showed cytotoxicity in human lung cell lines (A549) at concentrations ≥ 4 nM BaPeq. Using non-cytotoxic doses the extract was able to activate proteins involved in the DNA damage response pathway (Chk1 and p53). Moreover, the specific contribution of the four most representative PAHs in the cashew nut roasting sample showed that benzo[a]pyrene was the most efficient to activate Chk1 and p53. Finally, the organic extract was able to increase persistently the mRNA expression involved in the PAHs metabolism (CYP1A1 and CYP1B1), inflammatory response (IL-8 and TNF-α) and cell cycle arrest (CDKN1A) for DNA repair (DDB2). The high PM concentrations and its biological effects associated warn of the serious harmful effects of artisanal cashew nut roasting and urgent actions should be taken to the sustainable development of this activity.

Caracterização do material particulado e avaliação do risco ocupacional e mecanismos moleculares associados à queima artesanal da castanha de caju

Brazil is among the largest cashew nut producers of the world. However, the roasting process is still carried out artisanally, especially in the Brazilian semiarid region. In face of this occupational problem, the aim of this study was to perform a physical-chemical characterization of the particulate matter (PM) emitted by the roasting of cashew nuts, as well as to determine the occupational risk and molecular mechanisms associated. The most evident PM characteristics were the prevalence of fine particles, typical biomass burning morphologies such as tar ball and the presence of the elements K, Cl, S, Ca and Fe. In addition, atmospheric modeling analyses suggest that these particles can reach neighboring regions of the emission source. Polycyclic aromatic hydrocarbons (PAHs) with carcinogenic potential, such as benzo[a]pyrene, dibenz[a,h]anthracene, benzo[a]anthracene, benzo[b]fluoranthene, chrysene, benzo[k]fluoranthene, indeno[1,2,3-c,d]pyrene and benzo[j]fluoranthene were the most abundant PAHs found in the two air monitoring campaigns. Among the identified oxy-PAH the benzanthrone (7H-benz[d,e]anthracen-7-one) had the highest concentration and the evaluation of lifetime cancer risk showed an increase of 12 to 37 cases of cancer for every 10,000 exposed people. Chemical analysis of roasted cashew nuts identified the PAHs: phenanthrene, benzo[g,h,i]perylene, pyrene and benzo[a]pyrene, besides the 3-pentadecilfenol allergen (urushiol analogue) as prevalent. Occupational exposure to PAHs was confirmed by the increase of urinary 1-hydroxypyrene levels and genotoxic effects were evidenced by the increase on micronuclei and nuclear bud frequency in exfoliated buccal mucosa cells among the exposed workers. Other biomarkers of effects such as karyorrhexis, pyknotic, karyolytic, condensed chromatin and binucleated cells also have their frequencies increased when compared to an unexposed control group. The investigation of the molecular mechanisms associated with the PM organic extract showed cytotoxicity in human lung cell lines (A549) at concentrations ≥ 4 nM BaPeq. Using non-cytotoxic doses the extract was able to activate proteins involved in the DNA damage response pathway (Chk1 and p53). Moreover, the specific contribution of the four most representative PAHs in the cashew nut roasting sample showed that benzo[a]pyrene was the most efficient to activate Chk1 and p53. Finally, the organic extract was able to increase persistently the mRNA expression involved in the PAHs metabolism (CYP1A1 and CYP1B1), inflammatory response (IL-8 and TNF-α) and cell cycle arrest (CDKN1A) for DNA repair (DDB2). The high PM concentrations and its biological effects associated warn of the serious harmful effects of artisanal cashew nut roasting and urgent actions should be taken to the sustainable development of this activity.

Avaliação da influência de surfactantes químico e biológico na hidrólise enzimática de casca de coco verde após pré-tratamento ácido/alcalino e com peróxido de hidrogênio alcalino

In Brazil many types of bioproducts and agroindustrial waste are generated currently, such as cacashew apple bagasse and coconut husk, for example. The final disposal of these wastes causes serious environmental issues. In this sense, waste lignocellulosic content, as the shell of the coconut is a renewable and abundant raw material in which its use has an increased interest mainly for the 2nd generation ethanol production. The hydrolysis of cellulose to reducing sugars such as glucose and xylose is catalysed by a group of enzymes called cellulases. However, the main bottleneck in the enzymatic hydrolysis of cellulose is the significant deactivation of the enzyme that shows irreversible adsorption mechanism leading to reduction of the cellulose adsorption onto cellulose. Studies have shown that the use of surfactants can modify the surface property of the cellulose therefore minimizing the irreversible binding. The main objective of the present study was to evaluate the influence of chemical and biological surfactants during the hydrolysis of coconut husk which was subjected to two pre-treatment in order to improve the accessibility of the enzymes to the cellulose, removing this way, part of the lignin and hemicellulose present in the structure of the material. The pre-treatments applied to coconut bagasse were: Acid/Alkaline using 0.6M H2SO4 followed by 1M NaOH, and the one with Alkaline Hydrogen Peroxide at a concentration of 7.35% (v/v) and pH 11.5. Both the material no treatment and pretreated were characterized using analysis of diffraction X-ray (XRD), Scanning Electron Microscopy (SEM) and methods established by NREL. The influence of both surfactants, chemical and biological, was used at concentrations below the critical micelle concentration (CMC), and the concentrations equal to the CMC. The application of pre-treatment with coconut residue was efficient for the conversion to glucose, as well as for the production of total reducing sugars, it was possible to observe that the pretreatment fragmented the structure as well as disordered the fibers. Regarding XRD analysis, a significant increase in crystallinity index was observed for pretreated bagasse acid/alkali (51.1%) compared to the no treatment (31.7%), while that for that treated with PHA, the crystallinity index was slightly lower, around 29%. In terms of total reducing sugars it was not possible to observe a significant difference between the hydrolysis carried out without the use of surfactant compared to the addition of Triton and rhamnolipid. However, by observing the conversions achieved during the hydrolysis, it was noted that the best conversion was using the rhamnolipíd for the husk pretreated with acid/alkali, reaching a value of 33%, whereas using Triton the higher conversion was 23.8%. The coconut husk is a residue which can present a high potential to the 2nd generation ethanol production, being the rhamonolipid a very efficient biosurfactant for use as an adjuvant in the enzymatic process in order to act on the material structure reducing its recalcitrance and therefore improving the conditions of access for enzymes to the substrate increasing thus the conversion of cellulose to glucose.

Avaliação da influência de surfactantes químico e biológico na hidrólise enzimática de casca de coco verde após pré-tratamento ácido/alcalino e com peróxido de hidrogênio alcalino

In Brazil many types of bioproducts and agroindustrial waste are generated currently, such as cacashew apple bagasse and coconut husk, for example. The final disposal of these wastes causes serious environmental issues. In this sense, waste lignocellulosic content, as the shell of the coconut is a renewable and abundant raw material in which its use has an increased interest mainly for the 2nd generation ethanol production. The hydrolysis of cellulose to reducing sugars such as glucose and xylose is catalysed by a group of enzymes called cellulases. However, the main bottleneck in the enzymatic hydrolysis of cellulose is the significant deactivation of the enzyme that shows irreversible adsorption mechanism leading to reduction of the cellulose adsorption onto cellulose. Studies have shown that the use of surfactants can modify the surface property of the cellulose therefore minimizing the irreversible binding. The main objective of the present study was to evaluate the influence of chemical and biological surfactants during the hydrolysis of coconut husk which was subjected to two pre-treatment in order to improve the accessibility of the enzymes to the cellulose, removing this way, part of the lignin and hemicellulose present in the structure of the material. The pre-treatments applied to coconut bagasse were: Acid/Alkaline using 0.6M H2SO4 followed by 1M NaOH, and the one with Alkaline Hydrogen Peroxide at a concentration of 7.35% (v/v) and pH 11.5. Both the material no treatment and pretreated were characterized using analysis of diffraction X-ray (XRD), Scanning Electron Microscopy (SEM) and methods established by NREL. The influence of both surfactants, chemical and biological, was used at concentrations below the critical micelle concentration (CMC), and the concentrations equal to the CMC. The application of pre-treatment with coconut residue was efficient for the conversion to glucose, as well as for the production of total reducing sugars, it was possible to observe that the pretreatment fragmented the structure as well as disordered the fibers. Regarding XRD analysis, a significant increase in crystallinity index was observed for pretreated bagasse acid/alkali (51.1%) compared to the no treatment (31.7%), while that for that treated with PHA, the crystallinity index was slightly lower, around 29%. In terms of total reducing sugars it was not possible to observe a significant difference between the hydrolysis carried out without the use of surfactant compared to the addition of Triton and rhamnolipid. However, by observing the conversions achieved during the hydrolysis, it was noted that the best conversion was using the rhamnolipíd for the husk pretreated with acid/alkali, reaching a value of 33%, whereas using Triton the higher conversion was 23.8%. The coconut husk is a residue which can present a high potential to the 2nd generation ethanol production, being the rhamonolipid a very efficient biosurfactant for use as an adjuvant in the enzymatic process in order to act on the material structure reducing its recalcitrance and therefore improving the conditions of access for enzymes to the substrate increasing thus the conversion of cellulose to glucose.

Avaliação das condições de precipitação do azul da Prússia sobre pó de grafite visando o desenvolvimento de eletrodos de pasta de carbono para a quantificação de nitrito

An amperometric FIA method for nitrite quantification based on nitrite electroreduction and employing a carbon paste electrode (CPE) chemically modified with iron hexacyanoferrate (HCF) as an amperometric detector was developed. The influence of experimental conditions on the preparation of the electrode materials was evaluated and the materials obtained in each study were used for the development of modified electrodes. The electrochemical sensors were prepared by a fast, simple, and inexpensive procedure, and the long-term performance of the electrodes were quite satisfactory as the stability was maintained over one year. HCF was an effective redox mediator for nitrite electroreduction in acidic media, allowing nitrite detection at +0.2 V vs. Ag/AgClsat, which is a potential free of possible interfering species that are normally present in food and water samples. The electrochemical cell used in the FIA system was similar to a batch injection analysis cell, enabling recirculation of the carrier solution. This is an attractive feature because it allows the use of a high flow rate (6 mL min-1) leading to high sensitivity and analysis speed, while keeping reagent consumption low. The proposed method had a detection limit of 9 μmol L-1 and was successfully employed for nitrite quantification in spiked water and sausage samples. The obtained results were in good agreement with those provided by the spectrophotometric official method. At a 95 % confidence level it was not observed statistical differences neither in nitrite content nor in the precision provided by both methods. The experimental conditions for the synthesis of HCF were optimized and the best electrode material was prepared by mixing FeCl3, K4[Fe(CN)6] and carbon powder subjected to an acid and thermal treatment (400 ºC), followed by ultrasonic agitation at 4 °C. This material was used to construct an electrode with improved analytical performance to reduce nitrite, which presented greater stability compared to HCF film electrodeposited on the EPC, showing that the preparation procedure of the electrode material is an effective strategy for the development of HCF modified electrodes.

Caracterização e avaliação da atividade fotocatalítica de catalisadores baseados no TiO2, sintetizados mediante hidrólise em uma mistura de solventes

This study involved the synthesis of photocatalysts based on titanium dioxide (TiO2). The photocatalysts were synthesized by the sol-gel method using three different proportions of acetone (25%, 50% and 75% v/v) in water/acetone mixtures, in order to control the hydrolysis of the precursor of titanium (titanium tetraisopropoxide). Aiming to investigate the structural, morphological and electronic changes provoked by the use of the solvent mixtures, different methodologies were used to characterize the oxides, such as X-ray diffraction (XRD), RAMAN spectroscopy, UV-Vis diffuse reflectance spectroscopy, and measurements of specific surface area (BET). XRD combined to RAMAN analyses revealed that the products are two-phase highly crystalline oxides involving anatase as main phase and brookite. Besides, the refined XRD using the method of Rietveld demonstrated that the presence of acetone during the synthesis influenced in the composition of the crystalline phases, increasing the proportion of the brookite phase between 13 and 22%. The band gap energy of these oxides practically did not suffer changes as function of the synthesis conditions. As shown by the isotherm, these photocatalysts are mesoporous materials with mean diameter of pores of 7 nm and approximately 20% of porosity. The surface area of the oxides prepared by hydrolysis in presence of acetone was 12% higher compared to the bare oxide. After characterized, these oxides had their photocatalytic activities evaluated by photodegradation of the azo dyes Ponceau 4R (P4R), Tartrazine (TTZ) and Reactive Red 120 (RR120), and also by the ability to mediate the photocatalytic production of hydrogen. Using the most efficient photocatalyst, the mineralization achieved for the dyes P4R, RR120 and TTZ was of respectively 83%, 79% and 56% in 120 minutes of reaction, while the discoloration of P4R e RR120 reached 100% and 94% for TTZ. In addition, the same photocatalyst in the presence of 0.5% w/w of Platinum and suspended in a 5:1 v/v water/methanol mixture, produced 56 mmol of gaseous hydrogen in five hours of experiment, corresponding to a specific rate of hydrogen production of 139.5 mmol h-1 g-1.

Obtenção de triacetato de celulose a partir do bagaço de cana-deaçúcar para revestimento de micropartículas de goma gelana e avaliação do seu perfil de liberação in vitro e da mucoadesão ex vivo

Oral route of administration is considered to be the most comfortable, safe and greater adaptation for patients. But, oral route presents some disadvantages such as drugs bioavailability and side effects on the stomach. Some technologies are studied to soften and/or resolve these problems, such as coating with polymeric films, which are able to protect the pharmaceutical form of the acid stomachic environment and to act in the drug release, and mucoadhesive systems, which allow the pharmaceutical form remains a greater time interval in the intestine, increasing the effectiveness of the drug. Cellulose triacetate (CTA) films were produced from cellulose extracted from sugar cane bagasse. The films were prepared with different morphologies (with and without water, acting as non-solvent) and concentrations (3, 6.5 and 10%) of CTA and characterized using scanning electron microscopy (SEM), water vapor permeability (WVP), puncture resistance (PR), enzymatic digestion (DE), and mucoadhesive force evaluation (MF). Microscopy showed the formation of symmetric and asymmetric morphologies. WVP data showed that more concentrated films have higher values for WVP; moreover, asymmetric films had higher values than symmetric films. PR measurements showed that symmetric membranes are more resistant than asymmetric ones. More concentrated films were also more puncture resistant, except for symmetric membranes with CTA concentrations of 6.5 and 10% that did not show significant differences. All of the films presented large mucoadhesive capacities independent of their morphology and CTA concentration. From the results of WVP and RP, a symmetric filme with 6.5% CTA showed better ability and mechanical resistance, therefore, was selected to serve as coating of gellan gum (GG) particles incorporating ketoprofen (KET), which was confirmed by SEM. The selected film presented low values in measurements of the swelling index (SI) and in a dissolution test (DT). TGA analysis showed that the CTA coating does not influence the thermal stability of the particles and there is no incompatibility evidence between CTA, GG and KET. Coated particles released 100% of the ketoprofen in 24 h, while uncoated particles released the same amount in 4 h. The results of this study highlight the potential of CTA in the development of new controlled oral delivery systems.

Avaliação das Funções Executivas em Dependentes Químicos

The aim of this study was to investigate possible alterations in attentive functions and mental flexibility in individuals diagnosed with Addiction. The sample (n=40) was located for convenience, and included 20 individuals with addiction behaviors (G1), and 20 individuals who do not use harmfully psychoactive substances (G2). Assessment instruments used were: Experimental and Computerized Test of Continuous Performance, and the Wisconsin Card Sorting Test. It was concluded that individuals in the G1 group had a poorer performance in all categories analyzed on the Wisconsin Card Sorting Test and in reaction time on the Experimental and Computerized Test (p<0,05), showing a deficit in mental flexibility and attentive functions, which may have direct implications on addictive behaviors and treatment.

Desenvolvimento de um sumo de fruta com adição da macroalga Gelidium corneum, recorrendo à tecnologia HPP: caracterização físico-química, microbiológica e sensorial

No setor alimentar, o controlo da qualidade dos produtos e dos processos é uma etapa essencial, uma vez que é por este meio que se avaliam os padrões exigidos, quer a nível de legislação, quer a nível de mercado. O presente trabalho teve, como objetivos principais, o desenvolvimento de um novo produto alimentar com adição de algas, bem como o controlo de qualidade a nível de uma unidade fabril de produção de sumos e polpas naturais, à base de hortofrutícolas. De forma a garantir a qualidade na obtenção de produtos, foi realizado, diariamente, o controlo de entradas dos produtos hortofrutícolas, o acompanhamento de processos nas linhas de produção da fábrica e a análise das amostras de referência. Considerando a tendência e potencial de crescimento apresentados pelo setor das bebidas, nomeadamente dos sumos de fruta naturais, juntamente com a incessante procura por ingredientes naturais ricos em vários nutrientes e com propriedades bioativas, tem-se vindo a registar o lançamento de um número considerável de bebidas inovadoras, onde as macroalgas têm merecido um papel de destaque. Desta forma, procedeu-se à elaboração de dois protótipos, nomeadamente, sumo de framboesa e sumo de espinafres, com a adição do extrato da alga Gelidium corneum, estabilizados através do processo de Hiperpressão a frio, com o intuito de se avaliar o impacto desse extrato nos diferentes parâmetros de qualidade dos sumos. No que respeita aos parâmetros físico-químicos, o pH e teor de sólidos solúveis (TSS) foram avaliados após produção (t0), no tempo intermédio (t15) e no tempo final (t30). A cor foi determinada no t0 e no t30 e os restantes parâmetros, como acidez titulável, quantificação total de polifenóis, capacidade de redução do radical DPPH, teor de proteína bruta, teor de cinzas, teor de minerais e oligoelementos e teor de vitaminas (A, B1, B2 e C) foram avaliados no tempo final (t30). Foram, também, avaliados os parâmetros microbiológicos mais significativos, nomeadamente, microrganismos totais a 30 ˚C, Escherichia coli, Salmonella spp, bolores e leveduras (ao t0, t15 e t30) e realizou-se uma avaliação sensorial ao 29.º dia após produção. Estes sumos apresentaram-se microbiologicamente estáveis, não se tendo verificado crescimento microbiológico durante o período de armazenamento de 30 dias. A análise dos resultados físico-químicos permitiram constatar que a adição do extrato da alga Gelidium corneum aos sumos influenciou as suas características, tendo havido um aumento significativo do pH com a consequente diminuição da acidez titulável e um aumento do teor de sólidos solúveis, em comparação com os sumos controlo. Em relação à avaliação da cor, no caso das amostras de sumos de framboesa, verificou-se que a adição do extrato de algas influenciou o parâmetro a*. No entanto, ambas as amostras permitiram a manutenção deste parâmetro, ao longo do tempo. Quanto ao parâmetro b*, as duas amostras de sumo com algas demonstraram uma evolução mais estável, em relação aos respetivos controlos. No que respeita ao teor em minerais, a adição do extrato da alga demonstrou aumentar os teores de magnésio, sódio, potássio e iodo. Em termos sensoriais, o sumo de framboesa com algas obteve maior aceitação por parte do painel de provadores, podendo-se constatar que o atributo da cor foi o que mostrou maiores variações, entre as duas amostras.

Avaliação da potencialidade de argilas do Rio Grande do Norte – Brasil

DUTRA, Ricardo Peixoto Suassuna ; SILVA, Jaquelígia Brito da ; MORAES, Márcio Luiz Varela Nogueira de ; NASCIMENTO, R. M. ; GOMES, Uilame Umbelino ; PASKOCIMAS, Carlos Alberto . Avaliação da potencialidade de argilas do Rio Grande do Norte. Cerâmica Industrial, v. 13, p. 47-50, 2008.

Avaliação da interação entre aflatoxina M1 e B1 com a fração proteica do leite

Dissertação composta por 02 artigos.

Avaliação da potencialidade de argilas do Rio Grande do Norte – Brasil

DUTRA, Ricardo Peixoto Suassuna ; SILVA, Jaquelígia Brito da ; MORAES, Márcio Luiz Varela Nogueira de ; NASCIMENTO, R. M. ; GOMES, Uilame Umbelino ; PASKOCIMAS, Carlos Alberto . Avaliação da potencialidade de argilas do Rio Grande do Norte. Cerâmica Industrial, v. 13, p. 47-50, 2008.