Correlation between microtensile bond strength data and clinical outcome of Class V restorations.

OBJECTIVE: To determine if the results of resin-dentin microtensile bond strength (µTBS) is correlated with the outcome parameters of clinical studies on non-retentive Class V restorations. METHODS: Resin-dentin µTBS data were obtained from one test center; the in vitro tests were all performed by the same operator. The µTBS testing was performed 8h after bonding and after 6 months of storing the specimens in water. Pre-test failures (PTFs) of specimens were included in the analysis, attributing them a value of 1MPa. Prospective clinical studies on cervical restorations (Class V) with an observation period of at least 18 months were searched in the literature. The clinical outcome variables were retention loss, marginal discoloration and marginal integrity. Furthermore, an index was formulated to be better able to compare the laboratory and clinical results. Estimates of adhesive effects in a linear mixed model were used to summarize the clinical performance of each adhesive between 12 and 36 months. Spearman correlations between these clinical performances and the µTBS values were calculated subsequently. RESULTS: Thirty-six clinical studies with 15 adhesive/restorative systems for which µTBS data were also available were included in the statistical analysis. In general 3-step and 2-step etch-and-rinse systems showed higher bond strength values than the 2-step/3-step self-etching systems, which, however, produced higher values than the 1-step self-etching and the resin modified glass ionomer systems. Prolonged water storage of specimens resulted in a significant decrease of the mean bond strength values in 5 adhesive systems (Wilcoxon, p<0.05). There was a significant correlation between µTBS values both after 8h and 6 months of storage and marginal discoloration (r=0.54 and r=0.67, respectively). However, the same correlation was not found between µTBS values and the retention rate, clinical index or marginal integrity. SIGNIFICANCE: As µTBS data of adhesive systems, especially after water storage for 6 months, showed a good correlation with marginal discoloration in short-term clinical Class V restorations, longitudinal clinical trials should explore whether early marginal staining is predictive for future retention loss in non-carious cervical restorations.

Inexperienced sonographers can successfully visualize and assess a three-dimensional image of the fetal face using a standardized ultrasound protocol.

Introduction: A standardized three-dimensional ultrasonographic (3DUS) protocol is described that allows fetal face reconstruction. Ability to identify cleft lip with 3DUS using this protocol was assessed by operators with minimal 3DUS experience. Material and Methods: 260 stored volumes of fetal face were analyzed using a standardized protocol by operators with different levels of competence in 3DUS. The outcomes studied were: (1) the performance of post-processing 3D face volumes for the detection of facial clefts; (2) the ability of a resident with minimal 3DUS experience to reconstruct the acquired facial volumes, and (3) the time needed to reconstruct each plane to allow proper diagnosis of a cleft. Results: The three orthogonal planes of the fetal face (axial, sagittal and coronal) were adequately reconstructed with similar performance when acquired by a maternal-fetal medicine specialist or by residents with minimal experience (72 vs. 76%, p = 0.629). The learning curve for manipulation of 3DUS volumes of the fetal face corresponds to 30 cases and is independent of the operator's level of experience. Discussion: The learning curve for the standardized protocol we describe is short, even for inexperienced sonographers. This technique might decrease the length of anatomy ultrasounds and improve the ability to visualize fetal face anomalies.

Comparing simulation methods for modelling the errors of stand inventory data

Abstract

Evaluation of Appropriate Maintenance, Repair and Rehabilitation Methods for Iowa Bridges, TR-429, 2003

Most states, including Iowa, have a significant number of substandard bridges. This number will increase significantly unless some type of preventative maintenance is employed. Both the Iowa Department of Transportation and Iowa counties have successfully employed numerous maintenance, repair and rehabilitation (MR&R) strategies for correcting various types of deficiencies. However, successfully employed MR&R procedures are often not systematically documented or defined for those involved in bridge maintenance. This study addressed the need for a standard bridge MR&R manual for Iowa with emphasis for secondary road applications. As part of the study, bridge MR&R activities that are relevant to the state of Iowa have been systematically categorized into a manual, in a standardized format. Where pertinent, design guidelines have been presented. Material presented in this manual is divided into two major categories: 1) Repair and Rehabilitation of Bridge Superstructure Components, and 2) Repair and Rehabilitation of Bridge Substructure Components. There are multiple subcategories within both major categories that provide detailed information. Some of the detailed information includes step-by-step procedures for accomplishing MR&R activities, material specifications and detailed drawings where available. The source of information contained in the manual is public domain technical literature and information provided by Iowa County Engineers. A questionnaire was sent to all 99 counties in Iowa to solicit information and the research team personally solicited input from many Iowa counties as a follow-up to the questionnaire.

Retrofit Methods for Distortion Cracking Problems in Plate Girder Bridges, TR-436, 2003

This report is formatted to independently present four individual investigations related to similar web gap fatigue problems. Multiple steel girder bridges commonly exhibit fatigue cracking due to out-of-plane displacement of the web near the diaphragm connections. This fatigue-prone web gap area is typically located in negative moment regions of the girders where the diaphragm stiffener is not attached to the top flange. In the past, the Iowa Department of Transportation has attempted to stop fatigue crack propagation in these steel girder bridges by drilling holes at the crack tips. Other nondestructive retrofits have been tried; in a particular case on a two-girder bridge with floor beams, angles were bolted between the stiffener and top flange. The bolted angle retrofit has failed in the past and may not be a viable solution for diaphragm bridges. The drilled hole retrofit is often only a temporary solution, so a more permanent and effective retrofit is required. A new field retrofit has been developed that involves loosening the bolts in the connection between the diaphragm and the girders. Research on the retrofit has been initiated; however, no long-term studies of the effects of bolt loosening have been performed. The intent of this research is to study the short-term effects of the bolt loosening retrofit on I-beam and channel diaphragm bridges. The research also addressed the development of a continuous remote monitoring system to investigate the bolt loosening retrofit on an X-type diaphragm bridge over a number of months, ensuring that the measured strain and displacement reductions are not affected by time and continuous traffic loading on the bridge. The testing for the first three investigations is based on instrumentation of web gaps in a negative moment region on Iowa Department of Transportation bridges with I-beam, channel, and X-type diaphragms. One bridge of each type was instrumented with strain gages and deflection transducers. Field tests, using loaded trucks of known weight and configuration, were conducted on the bridges with the bolts in the tight condition and after implementing the bolt loosening retrofit to measure the effects of loosening the diaphragm bolts. Long-term data were also collected on the X-diaphragm bridge by a data acquisition system that collected the data continuously under ambient truck loading. The collected data were retrievable by an off-site modem connection to the remote data acquisition system. The data collection features and ruggedness of this system for remote bridge monitoring make it viable as a pilot system for future monitoring projects in Iowa. Results indicate that loosening the diaphragm bolts reduces strain and out-of-plane displacement in the web gap, and that the reduction is not affected over time by traffic or environmental loading on the bridge. Reducing the strain in the web gap allows the bridge to support more cycles of loading before experiencing fatigue, thus increase the service life of the bridge. Two-girder floor beam bridges may also exhibit fatigue cracking in girder webs.

Comparison of citrus rooting evaluation methods using root images in soil profiles and root weight

A digitized image method was compared with a standard washing technique for measuring citrus roots in the field. Video pictures of roots were taken in a soil profile. The profile area analyzed was defined by iron rings, which were also used to remove the roots to determine their dry weight. The roots presented in the pictures were quantified using SIARCS software developed by Embrapa. The root length and area determined by digital images provided a good estimate of root quantity present in the profile.

Comparison of methods for estimation of needle losses in Scots pine following defoliation by Bupalus piniaria

Abstract

Alternate Methods of Stabilizing Degrading Stream Channels in Western Iowa, Phase I, HR-208, 1980

Since the beginning of channel straightening at the turn of the century, the streams of western Iowa have degraded 1.5 to 5 times their original depth. This vertical degradation is often accompanied by increases in channel widths of 2 to 4 times the original widths. The deepening and widening of these streams has jeopardized the structural safety of many bridges by undercutting footings or pile caps, exposing considerable length of piling, and removing soil beneath and adjacent to abutments. Various types of flume and drop structures have been introduced in an effort to partially or totally stabilize these channels, protecting or replacing bridge structures. Although there has always been a need for economical grade stabilization structures to stop stream channel degradation and protect highway bridges and culverts, the problem is especially critical at the present time due to rapidly increasing construction costs and decreasing revenues. Benefits derived from stabilization extend beyond the transportation sector to the agricultural sector, and increased public interest and attention is needed.

Cava (Spanish sparkling wine) aroma: composition and determination methods

Cava (Spanish sparkling wine) is one of the mostimportant quality sparkling wines in Europe. It is produced by thetraditional method in which a base wine is re-fermented and agedin the same bottle that reaches the consumer. The special ageing incontact with lees gives the cava a particular bouquet with toasty,sweet or lactic notes. These nuances could be related with thechemical composition of aroma. The methods required to analyzethe flavor of cava are revised. Three approaches are necessary toobtain a wider profile: chemical, olfactometric and sensory.

The 2005 Pakistan earthquake revisited: Methods for integrated landslide assessment

Five years after the 2005 Pakistan earthquake that triggered multiple mass movements, landslides continue to pose a threat to the population of Azad Kashmir, especially during heavy monsoon rains. The thousands of landslides that were triggered by the 7.6 magnitude earthquake in 2005 were not just due to a natural phenomenon but largely induced by human activities, namely, road building, grazing, and deforestation. The damage caused by the landslides in the study area (381 km2) is estimated at 3.6 times the annual public works budget of Azad Kashmir for 2005 of US$ 1 million. In addition to human suffering, this cost constitutes a significant economic setback to the region that could have been reduced through improved land use and risk management. This article describes interdisciplinary research conducted 18 months after the earthquake to provide a more systemic approach to understanding risks posed by landslides, including the physical, environmental, and human contexts. The goal of this research is twofold: to present empirical data on the social, geological, and environmental contexts in which widespread landslides occurred following the 2005 earthquake; and, second, to describe straightforward methods that can be used for integrated landslide risk assessments in data-poor environments. The article analyzes limitations of the methodologies and challenges for conducting interdisciplinary research that integrates both social and physical data. This research concludes that reducing landslide risk is ultimately a management issue, based in land use decisions and governance.

A Study of Curing Methods and Type II Cements on the Durability of Concrete, R-11-Z(1), 1969

A program of A (90 day moist room), B (14 day moist room) and C (7 day moist room and 7 day 50%_humidity) type curing for the R-11-Z program of durability of concrete using the automatic freeze and thaw machine (ASTM C-291) has been used in the Materials Department of the Iowa State Highway Commission since December 6, 1966. A summary of the results obtained from then until March 25, 1968, indicates that the B and C type curing are yielding very little valuable information. However, the A cure exhibits a wide range of durability factors and also groups the aggregates in an order which is related to the service record (there are definite exceptions. The biggest disadvantage to the A cure is the length of time that it takes to complete the test (90 day cure and 38 day test). The Kansas Highway Department has experimented with different cements and aggregates in order to determine which combination offers a concrete with the best durability factor possible. In an experimental test section of highway, concrete made with a Type II cement appeared to have better durability than others made with Type I cements. Because of this, a question has been raised at the Iowa State Highway Commission - Can concrete made with Type II cements, because of a lesser amount of tricalcium aluminate, yield better durability than concrete made with Type I cements?

Efficiency of split nitrogen fertilization with adjusted irrigation on potato

Selostus: Jaetun typpilannoituksen käyttömahdollisuudet perunalle

INTERMED predicts non-return to work in an occupational rehabilitation setting for individuals with orthopaedic trauma-part 2

Introduction.- The model presented in part I (19 predictors) had good predictive values for non-return to work 2 years after vocational rehabilitation for orthopaedic trauma. However, the number of predictors is high for the detection of patients at risk in a clinic. For example, the INTERMED for itself consists of 20 questions and needs 20 minutes to be filled in. For this reason, the aim of this study was to compare the predictive value of different models for the prediction of non-return to work.Patients and methods.- In this longitudinal prospective study, the cohort consisted of 2156 included inpatients with orthopaedic trauma attending a rehabilitation hospital after a work, traffic, sport or leisure related injury. Two years after discharge, 1502 patients returned a questionnaire regarding return to work. We compared the area under the receiver-operator-characteristics curve (ROC) between different models: INTERMED total score, the 4 partial INTERMED scores, the items of the most predictive partial score; with or without confounders.Results.- The ROC for the total score of the INTERMED plus the five confounders of the of the part one (qualified work, speaking French, lesion of upper extremity, education and age) was 0.72. The sole partial INTERMED score to predict return to work was the social sub score. The ROC for the five items of the latter sub score of the INTERMED was 0.69. The ROC for the five items of the social subscale of the INTERMED combined with five predictors was 0.73. This was significantly better than the use of only the five items from INTERMED alone (delta 0.034; 95% CI 0.017 to .050). The model presented in part I (INTERMED total score plus 18 predictors) was not significantly better than the five items INTERMED social score plus five confounders.Discussion.- The use of a model with ten variables (INTERMED social five items plus five confounders) has good predictive value to detect patients not returning to work after vocational rehabilitation after orthopaedic trauma. The parsimony of this model facilitates its use in a clinic for the detection of patients at risk.