Atmospheric attenuation at 100 and 300 GHz estimated with radiosonde data

The study of atmospheric propagation impairments at submillimeter and THz frequencies is becoming increasingly relevant due to the strong effects caused by the composition of the troposphere and the phenomena occurring in it. The present paper is devoted to the estimation of total attenuation at 100 GHz and 300 GHz under non-rainy scenarios. With this purpose, 4 years of meteorological data from Madrid have been collected, including radiosoundings from Madrid-Barajas Airport and co-site SYNOP observations. This volume of data has been analyzed with the aim of also introducing a detection method of rain conditions, which cannot be easily identified in radiosounding profiles. Finally, the method has been used to discard several probable events which would be responsible of scattering conditions and, hence, yearly CDFs of total attenuation have been obtained. It is expected that the statistics would be closest to the ones obtained by experimental techniques under similar atmospheric conditions.

High Intensity Lasers Application to Advanced Materials Processing: Laser Peening and Related Processes

High Intensity Lasers Application to Advanced Materials Processing: Laser Peening and Related

Finite element simulation of sandwich panels of laminated plaster and rockwool under mixed mode fracture

Sandwich panels of laminated gypsum and rock wool have shown large pathology of cracking due to excessive slabs deflection. Currently the most widespread use of this material is as vertical elements of division or partition, with no structural function, what justifies that there are no studies on the mechanism of fracture and mechanical properties related to it. Therefore, and in order to reduce the cracking problem, it is necessary to progress in the simulation and prediction of the behaviour under tensile and shear load of such panels, although in typical applications have no structural responsability.

Development of a PWR-W and an AP1000® containment building 3D model with a CFD code for Best-Estimate Thermal-Hydraulic Analysis

The simulation of design basis accidents in a containment building is usually conducted with a lumped parameter model. The codes normally used by Westinghouse Electric Company (WEC) for that license analysis are WGOTHIC or COCO, which are suitable to provide an adequate estimation of the overall peak temperature and pressure of the containment. However, for the detailed study of the thermal-hydraulic behavior in every room and compartment of the containment building, it could be more convenient to model the containment with a more detailed 3D representation of the geometry of the whole building. The main objective of this project is to obtain a standard PWR Westinghouse as well as an AP1000® containment model for a CFD code to analyze the thermal-hydraulic detailed behavior during a design basis accident. In this paper the development and testing of both containment models is presented.

Networked Utopia : the Architecture and Urbanism of the Bata Shoe Company Satellite Cities = Utopia en red : arquitectura y urbanismo en las ciudades satélite de la Bata Shoe Company, 1930 al presente

From its humble beginnings as a small workshop established by Tomáš Baťa in 1874, the Bata Shoe Company became a gigantic concern in the 1920s, built on the principles of scientific management and welfare capitalism. The growth of the company engulfed Zlín (in today’s Czech Republic), its hometown, and transformed it into a modern industrial garden city satisfying the needs of both a growing industrial population, and those of the company itself. As a reaction to the aftermath of the crisis of 1929, the enterprise began a strategy of decentralization and international expansion characterized by the design and construction of a series of modern industrial towns that replicated the model of Zlín around the globe. This study is an exhaustive survey of these cities, their rationale, design, and their postindustrial conditions; it is a comparative work that has used field trips, photography, interviews, and archival material to explain the logics behind Bata’s project, to document the design and implementation of the model to multiple contexts and geographies, and to evaluate of the urban legacy of this undertaking. Finally, the research explores the question of what can the design disciplines, and other parties involved, learn from a full synthesis on the history and urbanism of the Bata satellite cities with regard to the re-imagination and sustainability of contemporary industry-sponsored interventions in developing geographies. RESUMEN Con origen en un humilde y pequeño taller fundado en 1874 por Tomáš Baťa, la Bata Shoe Company creció hasta convertirse en una gigantesca empresa en los anos 20, fundada en principios de control científico de la producción y capitalismo de bienestar. El crecimiento de la compañía se extendió por Zlín (en la actual República Checa), su pueblo de nacimiento, y la transformó en una moderna ciudad jardín industrial capaz de satisfacer las necesidades tanto de una población en alza como de la propia empresa. Como reacción a la crisis de 1929, Bata inició una estrategia de descentralización y expansión internacional caracterizada por el proyecto y construcción de modernas ciudades industriales que replicaron el modelo de Zlín por el mundo. Esta tesis es un estudio exhaustivo de estas ciudades: las razones detrás del proyecto, su diseño, y su condición post-industrial; es un estudio comparativo que se ha servido de trabajo de campo, documentación fotográfica, entrevistas y materiales de archivo para explicar la lógica detrás del proyecto de Bata, documentar el diseño e implementación de tal modelo en múltiples contextos y geografías, y valorar el legado urbano de esta empresa. Finalmente, la investigación evalúa qué podrían aprender las disciplinas del diseño y otras partes implicadas de una síntesis completa de la historia y el urbanismo de las ciudades satélite de Bata, en lo relativo a la reinvención y sostenibilidad de proyectos contemporáneos de la industria en geografías en desarrollo.

A Porposal: "Agro-ERASMUS"

The rural population is getting smaller as percentage of the total population in the countries. There is a constant depopulation of rural areas to urban areas. The most extreme data are in countries like USA, where the rural population is 1.5%, from which 1% of that amount is part time and only 0.5% full time. On the other side, we have countries with more than 50% rural population. Related to training, cultural development, business and specific weight in society, rural residents have no significance in their societies. As they are few, and separated across the territory they have no influence on their societies. Comparing the USA farmer with one from the EU, we see that the American one is a businessperson and the European one, in most cases is a farm worker. To reduce this gap between these different farmers, we believe that we must train the new generations of children belonging to farming Europe. They must have a common language, English; they must know other countries culture and farming systems, live and network with other young Europeans colleagues,future young farmers. It is what we have coined as AGRO-ERASMUS. A project to be placed within the EU Common Agriculture Policies. The project must be designed before its implementation. Even some previous experience should make better viability. It should make use of a network of agricultural universities in several European countries. Each university would build a "farm school" where young people would learn "English?, and visit and work in small agricultural practices with a correct use of the time. One important subject dealing with should be agribusiness. The procedure based on the ?Farm School? (F-S) experience, should start with young people from 13 years up to 18 years. Their attendance, every summer, to the F-S should be rotated between different countries besides their own. The first and second year, with young people 13/14 years old, the Farm School would last less than three weeks in an English speaking country (Ireland, UK or someone else). They should live with a local family the time they stay outside of the Farm School (F-S). This two years period must be devoted to learn and become familiar with the English language and cultural differences. The rest of the four years left, the Farm Schools will have longer duration and be placed in other countries from the network. The living way would be in multinational teams of young people where the only spoken language would be English. After six years of summer oexistence speaking English and learning new competences and skills with colleagues from other countries, we would have a great team of young and future European farmers, able to travel free and confident through the whole Europe and ready to be engaged in productive, commercial and research activities. These new young farmers may revive European agriculture and would not look any more like rural habitants, but international business-farmers, professionally speaking. In a brief survey among the assistants to the Fifth International Academic Conference titled "Alternative Income Sources in Small Agricultural Holdings of the European Union" held in Krakow (PL) in June 2015, participants from universities and countries like Poland, Hungary, Rep. Czech, Portugal, Romania, etc., expressed the necessity of addressing this problem in a new and bold way.

Sustainability in the Upper Colorado River Basin: A Struggle Between Water Resource Use and Remnants of the Natural Ecosystem

This study evaluated whether development of the Colorado River system has exceeded sustainability by comparing the trends in water use in the Colorado River. Two sustainable areas were identified in the upper basin and one in the lower-- the mainstream Colorado River, Green and Yampa rivers, and the Little Colorado River. These areas are also high priority recovery areas for four endangered fishes and protected by critical habitat provisions of the ESA. Unfortunately, the endangered fishes are declining because of habitat destruction and non-native species. If increasing water demand causes the fishes to go extinct the few sustainable areas will be lost. It will take careful management of the endangered fishes and water users to ensure these areas are maintained.

Removal of endocrine disrupting compounds from wastewater: a comparison between a conventional activated sludge with tertiary treatment and membrane bioreactors

Póster presentado en 19th International Congress of Chemical and Process Engineering, Prague, Czech Republic August 28th-September 1st, 2010.

Reduction of haloacetonitriles and haloacetones in natural waters using ceramic nanofiltration membranes

Póster presentado en 19th International Congress of Chemical and Process Engineering, Prague, Czech Republic August 28th-September 1st, 2010.

Stabilizing and Modulating Color by Copigmentation: Insights from Theory and Experiment

Natural anthocyanin pigments/dyes and phenolic copigments/co-dyes form noncovalent complexes, which stabilize and modulate (in particular blue, violet, and red) colors in flowers, berries, and food products derived from them (including wines, jams, purees, and syrups). This noncovalent association and their electronic and optical implications constitute the copigmentation phenomenon. Over the past decade, experimental and theoretical studies have enabled a molecular understanding of copigmentation. This review revisits this phenomenon to provide a comprehensive description of the nature of binding (the dispersion and electrostatic components of π–π stacking, the hydrophobic effect, and possible hydrogen-bonding between pigment and copigment) and of spectral modifications occurring in copigmentation complexes, in which charge transfer plays an important role. Particular attention is paid to applications of copigmentation in food chemistry.

Central Europe Region, 1730-1739 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Routes des postes et des voitures pour les marchandises et pour les voyages par l'Empire dans les principaux Etats de l'Europe, T. Stemmers, sculp. It was published by chez Reinier & Iosue Ottens, between 1730 and 1739. Scale [ca. 1:2,500,000]. Covers the Central Europe region. Map in French. The image inside the map neatline is georeferenced to the surface of the earth and fit to the Europe Lambert Conformal Conic coordinate system. All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as drainage, cities and other human settlements, roads, territorial and administrative boundaries, shoreline features, and more. Relief shown pictorially. Depths shown by shading.This layer is part of a selection of digitally scanned and georeferenced historic maps from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of originators, ground condition dates, scales, and map purposes.

Central Europe Region, ca. 1816 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Deutschland und der gröste Theil der umliegenden Staaten : oder Mittel-Europa in 35 Blättern : nach astronomischen Ortsbestimmungen und den besten Special-Karten, mit Rücksicht auf die neuesten Grenz-Bestimmungen entworfen, zufolge der Wiener Congress-Akte, des Pariser Friedens vom 21ten Nov. 1815, und der neuesten Austauschungen 1816, von H.H. Gotthold ; geschrieben und gestochen von H. Kliewer ; sämtliche Gebürge im Atlas sind gezeichnet und gestochen von Paulus Schmidt, so wie auch die Sectionen 3,11,16,18,19,21,25,26,31 von demselben gestochen worden. It was published by Simon Schropp & Co., ca. 1816. Scale [ca. 1:1,100,000]. Covers the Central Europe region. Map in German. The image inside the map neatline is georeferenced to the surface of the earth and fit to the Europe Lambert Conformal Conic coordinate system. All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as drainage, cities and other human settlements, roads, ground cover, territorial boundaries, shoreline features, and more. Relief shown by hachures. Depths shown by shading. Includes also inset index map.This layer is part of a selection of digitally scanned and georeferenced historic maps from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of originators, ground condition dates, scales, and map purposes.

Central Europe Region, 1859 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Neueste Eisenbahn-Karte von Central-Europa : mit genauer Angabe aller Stationen und den influirenden Post-Verbindungen, nach dem neuesten und zuverlässigsten Quellen bearbeitet von U. Hendschel. It was published by Carl Jügel's Verlag in 1859. Scale 1:1,900,000. Covers the Central Europe region. Map in German.The image inside the map neatline is georeferenced to the surface of the earth and fit to the Europe Lambert Conformal Conic coordinate system. All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as drainage, cities and other human settlements, roads, railroads, territorial and administrative boundaries, shoreline features, and more. Relief shown by hachures. Includes also scale comparison chart and index of political units.This layer is part of a selection of digitally scanned and georeferenced historic maps from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of originators, ground condition dates, scales, and map purposes.

Central Europe Region, 1872 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: Neueste Eisenbahn-Karte von Central-Europa : mit genauer Angabe aller Stationen und den influirenden Post-Verbindungen, nach dem neuesten und zuverlässigsten Quellen bearbeitet von U. Hendschel. It was published by Carl Jügel's Verlag in 1872. Scale 1:1,900,000. Covers the Central Europe region. Map in German. The image inside the map neatline is georeferenced to the surface of the earth and fit to the Europe Lambert Conformal Conic coordinate system. All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as drainage, cities and other human settlements, roads, railroads, territorial and administrative boundaries, shoreline features, and more. Relief shown by hachures. Includes also scale comparison chart and index of political units.This layer is part of a selection of digitally scanned and georeferenced historic maps from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of originators, ground condition dates, scales, and map purposes.

Central Europe Region, 1695 (Raster Image)

This layer is a georeferenced raster image of the historic paper map entitled: L'Empire d'Allemagne, divisé en tous ses estats : a l'usage de Monseigneur Le Duc De Bourgogne = Nova Imperii Germanici descriptio, in omnes suos circulos, electoratus, &c divisi : ad usum serenissimi Burgundiae Ducis, par ... H. Iaillot. It was published by H. Jaillot in 1695. Scale [ca. 1:2,400,000]. Covers the Central Europe region. Map in French and Latin. The image inside the map neatline is georeferenced to the surface of the earth and fit to the Europe Lambert Conformal Conic coordinate system. All map collar and inset information is also available as part of the raster image, including any inset maps, profiles, statistical tables, directories, text, illustrations, index maps, legends, or other information associated with the principal map. This map shows features such as drainage, cities and other human settlements, roads, territorial and administrative boundaries, shoreline features, and more. Relief shown pictorially.This layer is part of a selection of digitally scanned and georeferenced historic maps from the Harvard Map Collection. These maps typically portray both natural and manmade features. The selection represents a range of originators, ground condition dates, scales, and map purposes.