Adaptation of "Niagara Rosada" grape must to winemaking by partial cluster dehydration

This study aimed to verify the influence of partial dehydration of "Niagara Rosada" grape clusters in physicochemical quality of the pre- fermentation must. In Brazil, during the winemaking process it is common to need to adjust the grape must when the physicochemical characteristics of the raw material are insufficient to produce wines in accordance with the Brazilian legislation for classification of beverages, which establishes the minimum alcohol content of 8.6 % for the beverage to be considered wine. Therefore, given that the reduction in the water content of grape berries allows the concentration of chemical compounds present in its composition, especially the concentration of total soluble solids, we proceeded with the treatments that were formed by the combination of two temperatures (T1-37.1ºC and T2-22.9 ºC) two air speeds (S1: 1.79 m s-1 and S2: 3.21 m s-1) and a control (T0) that has not gone through the dehydration treatment. Analysis of pH, Total Titratable Acidity (TTA) were performed in mEq L-1, Total Soluble Solids (TSS) in ºBrix, water content on a dry basis and Concentration of Phenolic Compounds (CPC) in mg of gallic acid per 100g of must. The average comparison test identified statistically significant modifications for the adaptation of must for winemaking purposes, having the treatment with 22.9 ºC and air speed of 1.79 m s-1 shown the largest increase in the concentration of total soluble solids, followed by the second best result for concentration of phenolic compounds.

Evaluation of the effect of the seed extract of Moringa oleifera Lam over the efficiency of organic filters in wastewater treatment of dairy cattle breeding

This study aimed to evaluate the effect of Moringa oleifera Lam extract on the removal of total solids (TS), total suspended solids (TSS) and chemical oxygen demand (COD), in different filter media for treating wastewater of dairy cattle breeding (DCW). The moringa seed extract was obtained by grinding 50 g of seeds in one liter of distilled water and, after passing the solution through a quantitative paper filter of 25 microns, 60 mL of the extract were added to wastewater from cattle breeding before the filtration process in organic filters made of thin coal, bamboo leaves, eucalyptus leaves, gliricidia branches and sawdust. This was followed by the completely randomized experimental design, adopting a factorial of 5 x 2. Aliquots of filtered effluent were collected and the total solids (TS) concentrations, total suspended solids (TSS) and chemical oxygen demand (COD) were determined. It was found that the increase in the efficiency of removal of COD and total solids can be attributed to the coagulating power of the moringa seed extract, wherein the filter medium with bamboo leaves presented the best performance, showing potential for use as alternative filter material in the primary treatment of DCW.

Swine effluent treatment using anaerobic digestion at different loading rates

The industrial swine production is characterized by generation of significant effluent amounts that require treatment. The most adopted practices by Brazilian swine farmers have been wastewater storage in lagoons and its subsequent use as a biofertilizer. Nutrient accumulation in soil and water creates the need for an effective management of these residues. The anaerobic digestion process is an important alternative and low-cost treatment for organic matter reduction. However, its efficiency is limited by the digester capacity of solid degradation, especially at low hydraulic retention times. Thus, the present study aimed to verify the behavior of an upflow anaerobic digester by increasing the organic loading rate. This was accomplished in three stages using, as a parameter, volatile solids at 0.5; 1.0 and 1.5 kgVS m-3 d-1, respectively. This digester model proved to be quite robust and effective in swine manure treatment, achieving high efficiency of volatile solid removal at all stages of the study (stage 1: 61.38%; stage 2: 55.18%; and stage 3: 43.18%). Biogas production was directly related to the increasing organic load, reaching 0.14, 0.85, and 0.86 Nm³ kgVS-1add., respectively, with no significant difference (p<0.05) of biogas methane concentration among the studied stages (73.7, 75.0, and 77.9%).

Shewhart's control charts and process capability ratio applied to a sewage treatment station

The current study used statistical methods of quality control to evaluate the performance of a sewage treatment station. The concerned station is located in Cascavel city, Paraná State. The evaluated parameters were hydrogenionic potential, settleable solids, total suspended solids, chemical oxygen demand and biochemical oxygen demand in five days. Statistical analysis was performed through Shewhart control charts and process capability ratio. According to Shewhart charts, only the BOD(5.20) variable was under statistical control. Through capability ratios, we observed that except for pH the sewage treatment station is not capable to produce effluents under characteristics that fulfill specifications or standard launching required by environmental legislation.

Microencapsulation of pequi pulp by spray drying: use of modified starches as encapsulating agent

The aim of this study was to evaluate the microencapsulation of pequi pulp by spray drying. A central composite rotational design was used in order to evaluate the effect of the independent variables: inlet air temperature, surfactant concentration and modified starch concentration. The dependent variables were assumed as yield of the process and the product features microencapsulated. A selection of the best process condition was performed to obtain the best condition of a product with the highest vitamin C and carotenoids content. Powders showed moisture content below 2%. The experimental values of hygroscopicity, yield, water activity, total carotenoids and vitamin C powders ranged from 7.96 to 10.67 g of adsorbed water/100g of solids, 24.34 to 49.80%, 0.13 to 0.30, 145.78 to 292.11 mg of ascorbic acid/g of pequi solids and 15.51 to 123.42 mg of carotenoids/g of pequi solids, respectively. The inlet air temperature 140°C, the surfactant concentration of 2.5% and the modified starch concentration of 22.5% was recommended as the selected condition. By the scanning electron microscopy, it was observed that most of the particles had spherical shape and smooth surface.

COD, TSS, nutrients and coliforms removals in UASB reactors in two stages treating swine wastewater

The performance of two upflow anaerobic sludge blanket (UASB) reactors was evaluated in pilot scale (908 and 188 L), installed in series (R1 and R2), fed with swine wastewater with TSS around 5 and 13 g L-1. The UASB reactors were submitted to HDT of 36 and 18 h with VOL of 5.5 to 34.4 g COD (L d)-1 in the R1 and HDT of 7.5 e 3.7 h with VOL from 5.1 to 45.2 g COD (L d)-1 in the R2. The average removal efficiencies of COD ranged from 55 to 85% in the R1 and from 43 to 57% in the R2, resulting in values from 82 to 93% in the UASB reactors in two stage. Methane concentrations in the biogas were 69 to 74% with specific production from 0.05 to 0.27 L CH4 (g removedCOD)-1 in the R1 and of 0.10 to 0.12 L CH4 (g removedCOD)-1 in the R2. The average removal efficiencies were 61 to 75% for totalP, 39 to 69% for KN, 82 to 93% for orgN and 20 to 94% for Fe, Zn, Cu and Mn. The amN concentration were not reduced indicating the need to post-treatment for effluent disposal into water bodies. There were reductions of total coliforms from 99.8123 to 99.9989% and of thermotolerant coliforms from 99.9725 to 99.9999%. The conditions imposed to the UASB reactors in two stage provided high conversions of removedCOD into methane (up to 77%) and reductions of organic an inorganic pollution loads from swine wastewater.

Cassava starch extraction effluent treatment in a one phase tubular horizontal pilot reactor with support medium

The cassava starch industries generate a large volume of wastewater effluent that, stabilized in ponds, wastes its biogas energy and pollutes the atmosphere. To contribute with the reversion of this reality, this manipueira treatment research was developed in one phase anaerobic horizontal pilot reactor with support medium in bamboo pieces. The reactor was excavated into the ground and sealed with geomembrane in HDPE, having a volume equal to 33.6 m³ and continuous feeding by gravity. The stability indicators were pH, volatile acidity/total alkalinity ratio and biogas production. The statistical analyses were performed by a completely randomized design, with answers submitted to multivariate analysis. The organical loads in COD were 0.556; 0.670; 0.678 and 0.770 g L-1 and in volatile solids (VS) of 0.659; 0.608; 0.570 and 0.761 g L-1 for the hydraulic retention times (HRT) of 13.0; 11.5; 10.0 and 7.0 days, respectively. The reductions in COD were 88; 80; 88 and 67% and for VS of 76; 77; 65 and 61%. The biogas productions relatively to the consumed COD were 0.368; 0.795; 0.891 and 0.907 Lg-1, for the consumed VS of 0.524; 0.930; 1.757 and 0.952 Lg-1 and volumetric of 0.131; 0.330; 0.430 and 0.374 L L-1 d-1. The reactor remained stable and the bamboo pieces, in visual examination at the end of the experiment, showed to be in good physical conditions.

Color change and quality response of ‘lane late’ orange submitted to degreening process

This study aimed at evaluating the effects of ethylene on peel color and compositional changes in ‘Lane late’ orange stored under refrigerated and ambient conditions. Physiologically mature, but green-peeled, oranges were exposed to ethylene gas under room temperature and high relative humidity for 24 hours. Storage chamber was ventilated with fresh air after 12 hours to mitigate consequences derived from fruit respiration. Both nondestructive analysis, such as peel color (hue angle, chromaticity, and brightness) and weight loss, and destructive ones (soluble solids, titratable acidity, pH, soluble solids to acidity ratio, and puncture force) were performed upon harvest, after degreening, and every three days during eighteen days in storage. Experiment was carried out using an entirely randomized design with thirty replications for nondestructive and four replications for destructive analyses, in a split plot scheme. Exposure to ethylene ensured a golden yellow peel for both fruit stored under ambient and refrigerated conditions. High relative humidity, associated with low temperature prevented fruit from losing moisture. Fruit exposure to ethylene did not affect weight loss, soluble solids, titratable acidity, pH, soluble solids, acidity ratio, or puncture force.

Mechanical damage during harvest and loading affect orange postharvest quality

Brazil is the world’s largest orange producer; however, part of this production is lost during postharvest. This loss can be minimized by controlling incidence of physical damage throughout the harvest and loading operations. Impacts can negatively modify quantitative and qualitative fruits aspects. The main goal of this study was to measure the impact magnitude in two types of harvest (manual and detachment) and during all steps from picking into bags until loading for transport to the processing industry and additionally evaluating, in laboratory, the physico-chemical quality of the fruit subjected to various impacts, similar to those found in the field. In order to evaluate the impact magnitude, an instrumented sphere was used (760 mm, Techmark, Inc, USA). The following physico-chemical parameters were evaluated during 6-days of storage: weight loss, soluble solids contents, titratable acidity, ascorbic acid content, pH, firmness and peel color. The greatest impacts were observed during harvest, during the detachment practice, and when loading and unloading from bulk storage, with average acceleration values between 249.5 and 531.52G. The impact incidence in oranges were responsible for reducing the soluble solids, titratable acidity, ascorbic acid and weight by to 5.5%; 8.7%; 4.6% and 0.5%, respectively, compared to the control. Impacts during harvest and the various pre-industry manipulation steps must be controlled as they interfere in postharvest quality and physiology of ‘Valência’ oranges.

Start-up of anaerobic reactors for slaughterhouse wastewater treatment

This study aimed to evaluate the start-up of a horizontal anaerobic fixed bed reactor (HAFBR) followed by an upflow anaerobic sludge blanket (UASB) for the slaughterhouse wastewater treatment. HAFBR was filled with bamboo rings and had 1.2 m in length, 0.10 m in diameter and volume of 7.5 L. The UASB had the volume of 15 L. The HAFBR and UASB operated at organic loading rate and hydraulic retention time average of 8.46 and 3.77 kg m-3 d-1 of COD and 0.53 and 0.98 days, respectively. During 150 days of monitoring system it was found pH 6.8, relatively high values of bicarbonate alkalinity (> 1000 mg L-1) and reduced values of volatile acids (70 to 150 mg L-1), which afforded average removal efficiencies of COD total and total suspended solids of the order of 31 and 23% in HAFBR and 79% and 63% in UASB. It can be concluded that the generation and consumption of bicarbonate alkalinity and total volatile acids, thereby maintaining the pH during the study indicated stable operation of the reactors. The COD removal in the reactors was satisfactory especially when it considers that the assessment was conducted in a period of adaptation of organisms to the effluent and also the high organic load applied during this period.

Soil physical attributes in chemigated banana plantation with wastewater

ABSTRACT The feasibility of using sewage wastewater as a water and nutrient source for plants is an alternative to harness agricultural natural resource, observing its influence on the organic matter dynamics and soil energy. Our objective here was to evaluate the effects of applying different doses of effluent from a sewage treatment plant, in Janaúba – MG, Brazil, over the physical attributes of a soil grown with “Prata Anã” banana. From soil sample collection at depths of 0-20, 20-40, and 40-60 cm, we determined the following soil properties: soil density, total porosity, macroporosity, microporosity, organic matter, clay dispersed in water and stability of soil aggregate. The experimental design was in randomized blocks with four repetitions. Wastewater raising doses promoted increase in suspended solids, contributing to macroporosity reduction at 20-40 and 40-60 cm depths; as well as a reduction in organic matter within 0-20 cm layer. Clay dispersal was observed in the depths of 0-20 cm, being derived from an increase in sodium content. Concurrently, there was a reduction of soil aggregate stability.

Spraying systems and traveling speed in the deposit and spectrum of droplets in cotton plant

ABSTRACT Tractor traveling speed can influence the quality of spraying depending on the application technology used. This study aimed to evaluate the droplet spectrum, the deposition and uniformity of spray distribution with different spraying systems and traveling speeds of a self-propelled sprayer in two phenological stages of the cotton plant (B9 and F13). The experimental design was randomized blocks and treatments were three spraying techniques: common flat spray tips; tilted flat jet with air induction, at 120 L ha-1; and rotary atomizer disk, 20 L ha-1, combined with four traveling speeds: 12, 15, 18 and 25 km h-1, with four replications. Spraying deposition was evaluated for both leaf surfaces from the cotton plant apex and base (stage B9) and middle part of the plant (stage F13) with a cupric marker. A laser particle analyzer also assessed the droplet spectrum. The centrifugal power spray system produces more homogeneous droplet spectrum and increased penetration of droplets into the canopy in both phenological stages. Variation on the operating conditions necessary for increased traveling speed negatively influences the pattern of spraying deposits.

Exérese de leiomioma esofágico por toracotomia

A 49yrs old, male patient presented progressive dysphagia during the last two years, initially to solids and, since two weeks, liquids he had lost 15 kilos. Esophagogram showed an intraluminal lesion with regular mucosa in the middle third of esophagus. The esophagoscopy exhibits regular mucosa up to the lesion, which did not alow passage. There was no evidence of linfonodal disease at CT scan. The hypothesis of esophageal leiomyoma led this patient a right posterior thoracotomy and enucleation of a 30 x 30 mm mass from the esophageal wall. With this case report we intend to review esophageal leiomyomas and their diagnosis and treatment.

The Finnish Paper Workers' Union at a crossroads: Labor union representativeness in a changing environment, 1980-2008

This thesis consists of four articles and an introductory section. The main research questions in all the articles refer to the changes in the representativeness of the Finnish Paper Workers' Union. Representativeness stands for the entire entity of external, internal, legal and reputational factors that enable the labor union to represent its members and achieve its goals. This concept is based on an extensive reading of quantitative and qualitative industrial relations literature, which includes works based on Marxist labor-capital relations (such as Hyman's industrial relations studies), and more recent union density studies as well as gender- and ethnic diversity-based 'union revitalization' studies. Müller-Jentsch's German studies of industrial relations have been of particular importance as well as Streeck's industrial unionism and technology studies. The concept of representativeness is an attempt to combine the insights of these diverse strands of literature and bring the scientific discussion of labor unions back to the core of a union's function: representing its members. As such, it can be seen as a theoretical innovation. The concept helps to acknowledge both the heterogeneity of the membership and the totality of a labor union organization. The concept of representativeness aims to move beyond notions of 'power'. External representativeness can be expressed through the position of the labor union in the industrial relations system and the economy. Internal representativeness focuses on the aspects of labor unions that relate to the function of the union as an association with members, such as internal democracy. Legal representativeness lies in the formal legal position of the union – its rights and instruments. This includes collective bargaining legislation, co-decision rules and industrial conflict legislation. Reputational representativeness is related to how the union is seen by other actors and the general public, and can be approximated using data on strike activity. All these aspects of representativeness are path-dependent, and show the results of previous struggles over issues. The concept of representativeness goes beyond notions of labor union power and symbolizes an attempt to bring back the focus of industrial relations studies to the union's basic function of representing its members. The first article shows in detail the industrial conflict of the Finnish paper industry in 2005. The intended focus was the issue of gender in the negotiations over a new collective agreement, but the focal point of the industrial conflict was the issue of outsourcing and how this should be organized. Also, the issue of continuous shifts as an issue of working time was very important. The drawn-out conflict can be seen as a struggle over principles, and under pressure the labor union had to concede ground on the aforementioned issues. The article concludes that in this specific conflict, the union represented its' female members to a lesser extent, because the other issues took such priority. Furthermore, because of the substantive concessions. the union lost some of its internal representativeness, and the stubbornness of the union may have even harmed the reputation of the union. This article also includes an early version of the representativeness framework, through which this conflict is analyzed. The second article discusses wage developments, union density and collective bargaining within the context of representativeness. It is shown that the union has been able to secure substantial benefits for its members, regardless of declining employment. Collective agreements have often been based on centralized incomes policies, but the paper sector has not always joined these. Attention is furthermore paid to the changing competition of the General Assembly, with a surprisingly strong position of the Left Alliance still. In an attempt to replicate analysis of union density measures, an analysis of sectoral union density shows that similar factors as in aggregate data influence this measure, though – due to methodological issues – the results may not be robust. On this issue, it can be said that the method of analysis for aggregate union density is not suitable for sectoral union density analysis. The increasingly conflict-ridden industrial relations predicted have not actually materialized. The article concludes by asking whether the aim of ever-increasing wages is a sustainable one in the light of the pressures of globalization, though wage costs are a relatively small part of total costs. The third article discusses the history and use of outsourcing in the Finnish paper industry. It is shown using Hyman's framework of constituencies that over time, the perspective of the union changed from 'members of the Paper Workers' Union' to a more specific view of who is a core member of the union. Within the context of the industrial unionism that the union claims to practice, this is an important change. The article shows that the union more and more caters for a core group, while auxiliary personnel is less important to the union's identity and constituencies, which means that the union's internal representativeness has decreased. Maintenance workers are an exception; the union and employers have developed a rotating system that increases the efficient allocation of these employees. The core reason of the exceptional status of maintenance personnel is their high level of non-transferable skills. In the end it is debatable whether the compromise on outsourcing solves the challenges facing the industry. The fourth article shows diverging discourses within the union with regard to union-employer partnership for competitiveness improvements and instruments of local union representatives. In the collective agreement of 2008, the provision regulating wage effects of significant changes in the organization or content of work was thoroughly changed, though this mainly reflected decisions by the Labor Court on the pre-2008 version of the provision. This change laid bare the deep rift between the Social Democratic and Left Alliance (ex-Communist) factions of the union. The article argues that through the changed legal meaning of the provision, the union was able to transform concession bargaining into a basis for partnership. The internal discontent about this issue is nonetheless substantial and a threat to the unity of the union, both locally and at the union level. On the basis of the results of the articles, other factors influencing representativeness, such as technology and EU law and an overview of the main changes in the Finnish paper industry, it is concluded that, especially in recent years, the Finnish Paper Workers' Union has lost some of its representativeness. In particular, the loss of the efficiency of strikes is noted, the compromise on outsourcing which may have alienated a substantial part of the union's membership, and the change in the collective agreement of 2008 have caused this decline. In the latter case, the internal disunion on that issue shows the constraints of the union's internal democracy. Furthermore, the failure of the union to join the TEAM industrial union (by democratic means), the internal conflicts and a narrow focus on its own sector may also hurt the union in the future, as the paper industry in Finland is going through a structural change. None of these changes in representativeness would have been so drastic without the considerable pressure of globalization - in particular changing markets, changing technology and a loss of domestic investments to foreign investments, which in the end have benefited the corporations more than the Finnish employees of these corporations. Taken together, the union risks becoming socially irrelevant in time, though it will remain formally very strong on the basis of its institutional setting and financial situation.

Verhopäällystyspastojen analyysimenetelmät

Diplomityön tarkoitus oli selvittää verhopäällystyspastoille sopivia analyysimenetelmiä. Verhopäällystyksessä onnistunut päällystystapahtuma vaatii venymäviskositeetin ja pintajännityksen hyvää hallintaa. Kirjallisuusosassa käsiteltiin verhopäällystystä, verhopäällystyspastojen koostumusta, reologiaa ja pintajännitystä. Kirjallisuusosassa käsiteltiin lisäksi verhopäällystyspastojen reologian ja pintajännityksen mittaamiseen soveltuvia mittausmenetelmiä. Verhopäällystyksen luonteen vuoksi kirjallisuusosassa syvennyttiin venymäviskositeetin ja dynaamisen pintajännityksen mittaamiseen tarkoitettuihin menetelmiin. Kokeellisessa osassa tutkittiin päällystyspastasarjojen reologiaa ja pintajännitystä verhopäällystystä varten. Osaan päällystyspastoista luotiin venymäviskositeettia ja osasta laskettiin pintajännitystä. Venymäviskositeetin mittaamista varten työssä käytettiin ACAV A2 -reometriin liitettyjä teräsreikälevyjä. Dynaamisen pintajännityksen mittaamista varten työssä käytettiin KSV BPA-800P -pintajännitysmittaria. ACAV A2 -reometriin liitettyjen teräsreikälevyjen (reiän sisähalkaisija 0,5 tai 0,7 mm) avulla mitattiin venymäviskositeettia kuvaavia Eulerin lukuarvoja onnistuneesti suurilla kiintoainepitoisuuksilla (50, 60 tai 65 p %). Erikoispaksuntajan määrää lisäämällä onnistuttiin luomaan huomattavaa venymäviskositeettia. Kiintoainepitoisuuden kasvaessa kasvoi myös venymäviskositeetti. Tavanomaisille paksuntajille mitattiin hieman kohonneita venymäviskositeetteja verrattuna referenssipäällystyspastaan. Pigmenttikoostumuksella (kalsiumkarbonaatti/kaoliini) ei näyttänyt olevan vaikutusta venymäviskositeettiin, tai vaikutus oli suhteellisen pieni. Dynaamisen pintajännityksen mittaamista varten käytössä ollut KSV BPA-800P -pintajännitysmittari ei toiminut luotettavasti, vaikka näytteitä laimennettiin. Kiintoainepitoisuudessa 10 p-% olleilla laimennoksilla saavutettiin analysoinnin kannalta parhaat tulokset. Tuloksista saatiin kuitenkin viitteitä, että kyseinen mittari voisi olla potentiaalinen menetelmä dynaamisen pintajännityksen mittaamiseksi.