Enhancing spiral-wound ultrafiltration performance for direct drinking water treatment through operational procedures improvement: A feasible option for the Sao Paulo Metropolitan Region

This work aimed to evaluate the influence of specific operational conditions on the performance of a spiral-wound ultrafiltration pilot plant for direct drinking water treatment, installed at the Guarapiranga's reservoir, in the Sao Paulo Metropolitan Region. Results from operational tests showed that the volume of permeate produced in the combination of periodic relaxation with flushing and chlorine dosage procedures was 49% higher than the volume obtained when these procedures were not used. Two years of continuous operation demonstrated that the ultrafiltration pilot plant performed better during fall and winter seasons, higher permeate flow production and reduced chemical cleanings frequency. Observed behavior seems to be associated with the algae bloom events in the reservoir, which are more frequent during spring and summer seasons, confirmed by chlorophyll-a analysis results. Concentrate clarification using ferric chloride was quite effective in removing NOM and turbidity, allowing its recirculation to the ultrafiltration feed tank. This procedure made it possible to reach almost 99% water recovery considering a single 54-hour recirculation cycle. Water quality monitoring demonstrated that the ultrafiltration pilot plant was quite efficient, and that potential pathogenic organisms, Escherichia coil and total coliforms, turbidity and apparent color removals were 100%, 95.1%, and 91.5%, respectively. (C) 2012 Elsevier B.V. All rights reserved.

Swelling tests on material from the Guabirotuba Formation, Parana, Brazil, with suction control

This paper presents the swelling behaviour of clayey materials under controlled suction imposed both by a Richards chamber and by controlling the relative humidity with concentrated saline solutions. Soil-water characteristic curves (matrix and total) were determined by the filter paper method. The materials under study belong to the Guabirotuba Formation, of Pleistocene age, in the Curitiba Basin in the state of Parana, southern Brazil. Materials under several stages of suction of 5000-40 000 kPa were subjected to swelling tests in an oedometer press. The results indicated that the greater the suction the higher the swelling pressure. However, when swelling tests were carried out with suction variation controlled by relative humidity, in which the increase in moisture was very slow, the samples showed no swelling.

Purification and characterization of a surfactin-like molecule produced by Bacillus sp. H2O-1 and its antagonistic effect against sulfate reducing bacteria

Abstract Background Bacillus sp. H2O-1, isolated from the connate water of a Brazilian reservoir, produces an antimicrobial substance (denoted as AMS H2O-1) that is active against sulfate reducing bacteria, which are the major bacterial group responsible for biogenic souring and biocorrosion in petroleum reservoirs. Thus, the use of AMS H2O-1 for sulfate reducing bacteria control in the petroleum industry is a promising alternative to chemical biocides. However, prior to the large-scale production of AMS H2O-1 for industrial applications, its chemical structure must be elucidated. This study also analyzed the changes in the wetting properties of different surfaces conditioned with AMS H2O-1 and demonstrated the effect of AMS H2O-1 on sulfate reducing bacteria cells. Results A lipopeptide mixture from AMS H2O-1 was partially purified on a silica gel column and identified via mass spectrometry (ESI-MS). It comprises four major components that range in size from 1007 to 1049 Da. The lipid moiety contains linear and branched β-hydroxy fatty acids that range in length from C13 to C16. The peptide moiety contains seven amino acids identified as Glu-Leu-Leu-Val-Asp-Leu-Leu. Transmission electron microscopy revealed cell membrane alteration of sulfate reducing bacteria after AMS H2O-1 treatment at the minimum inhibitory concentration (5 μg/ml). Cytoplasmic electron dense inclusions were observed in treated cells but not in untreated cells. AMS H2O-1 enhanced the osmosis of sulfate reducing bacteria cells and caused the leakage of the intracellular contents. In addition, contact angle measurements indicated that different surfaces conditioned by AMS H2O-1 were less hydrophobic and more electron-donor than untreated surfaces. Conclusion AMS H2O-1 is a mixture of four surfactin-like homologues, and its biocidal activity and surfactant properties suggest that this compound may be a good candidate for sulfate reducing bacteria control. Thus, it is a potential alternative to the chemical biocides or surface coating agents currently used to prevent SRB growth in petroleum industries.

Characterization of lyophilized liposomes produced with non-purified soy lecithin: a case study of casein hydrolysate microencapsulation

A commercial casein hydrolysate was microencapsulated in liposomes produced with non-purified soy lecithin, cryoprotected with two different disaccharides and lyophilized. The encapsulation efficiency of casein hydrolysate ranged from 30 to 40%. The powders were analyzed by differential scanning calorimetry (DSC), scanning electron micrography (SEM), infrared spectroscopy (FTIR) and wide angle X-ray diffraction (WAXD). DSC data revealed the presence of an exothermal transition in empty lyophilized liposomes, which was ascribed to the presence of a quasicrystalline lamellar phase (intermediary characteristics between the Lβ and Lc phases). The addition of peptides to the liposomal system caused the disappearance of this exothermic phenomenon, as they were located in the polar headgroup portion of the bilayer, causing disorder and preventing the formation of the quasicrystalline phase. Infrared data indicated the presence of the peptides in the lyophilized formulations and showed that the cryoprotectants interacted effectively with the polar heads of phospholipids in the bilayer.

The star formation rate in the inner Milky Way Galaxy

The present star formation rate (SFR) in the inner Galaxy is puzzling for the chemical evolution models (CEM). No static CEM is able to reproduce the peak of the SFR in the 4 kpc ring. The main reason is probably a shortage of gas, which could be due to the dynamical effects produced by the galactic bar, not considered by these models. We developed a CEM that includes radial gas flows in order to mimic the effects of the galactic bar in the first 5 kpc of the galactic disk. In this model, the star formation (SF) is a two-step process: first, the diffuse gas forms molecular clouds. Then, stars form from cloud-cloud collisions or by the interaction between massive stars and the molecular gas. The former is called spontaneous and the latter induced SF. The mass in the different phases of each region changes by the processes associated with the stellar formation and death by: the SF due to spontaneous fragmentation of gas in the halo; formation of gas clouds in the disk from the diffuse gas; induced SF in the disk due to the interaction between massive stars and gas clouds; and finally, the restitution of the diffuse gas associated to these process of cloud and star formation. In the halo, the star formation rate for the diffuse gas follows a Schmidt law with a power n = 1.5. In the disk, the stars form in two steps: first, molecular clouds are formed from the diffuse gas also following a Schmidt law with n=1.5 and a proportionality factor. Including a specific pattern of radial gas flows, the CEM is able to reproduce with success the peak in the SFR at 4 kpc (fig. 1).

Investigation of the interaction of alkali ions with surfactant head groups for the formation of lyotropic biaxial nematic phase via optical birefringence measurements.

Lyotropic liquid crystals exhibiting nematic phases were obtained from the mixtures potassium laurate/alkali sulfate salts (M2SO4)/1-undecanol (UndeOH)/water and sodium dodecyl sulfate (SDS)/M2SO4/1-dodecanol (DDeOH)/water, where M2SO4 represents the alkali sulfate salts being Li2SO4, Na2SO4, K2SO4, Rb2SO4 or Cs2SO4. The birefringences measurements were performed via laser conoscopy. Our results indicated that cosmotropic and chaotropic behaviors of both ions and head groups are very important to obtain lyotropic biaxial nematic phase. To obtain the biaxial nematic phase, surfactant head group and ion present in lyotropic mixture have relatively opposite behavior, e.g. one more cosmotropic (more chaotropic) other less cosmotropic (less chaotropic) or vice versa.

Simulations of glacial/interglacial cycles with simple box-models. The ocean CO2 source during deglaciations

Máster en Oceanografía

Role of xanthophyll and water-water cycles in the protection of photosynthetic apparatus in Arbutus unedo and Arabidopsis thaliana

Photosynthetic organisms have sought out the delicate balance between efficient light harvesting under limited irradiance and regulated energy dissipation under excess irradiance. One of the protective mechanisms is the thermal energy dissipation through the xanthophyll cycle that may transform harmlessly the excitation energy into heat and thereby prevent the formation of damaging active oxygen species (AOS). Violaxanthin deepoxidase (VDE) converts violaxanthin (V) to antheraxanthin (A) and zeaxanthin (Z) defending the photosynthetic apparatus from excess of light. Another important biological pathway is the chloroplast water-water cycle, which is referred to the electrons from water generated in PSII reducing atmospheric O2 to water in PSI. This mechanism is active in the scavenging of AOS, when electron transport is slowed down by the over-reduction of NADPH pool. The control of the VDE gene and the variations of a set of physiological parameters, such as chlorophyll florescence and AOS content, have been investigated in response to excess of light and drought condition using Arabidopsis thaliana and Arbutus unedo.. Pigment analysis showed an unambiguous relationship between xanthophyll de-epoxidation state ((A+Z)/(V+A+Z)) and VDE mRNA amount in not-irrigated plants. Unexpectedly, gene expression is higher during the night when xanthophylls are mostly epoxidated and VDE activity is supposed to be very low than during the day. The importance of the water-water cycle in protecting the chloroplasts from light stress has been examined through Arabidopsis plant with a suppressed expression of the key enzyme of the cycle: the thylakoid-attached copper/zinc superoxide dismutase. The analysis revealed changes in transcript expression during leaf development consistent with a signalling role of AOS in plant defence responses but no difference was found any in photosynthesis efficiency or in AOS concentration after short-term exposure to excess of light. Environmental stresses such as drought may render previously optimal light levels excessive. In these circumstances the intrinsic regulations of photosynthetic electron transport like xanthophyll and water-water cycles might modify metabolism and gene expression in order to deal with increasing AOS.

Stratigraphy and Palaeontology of the Late Cretaceous Wapiti Formation, west-central Alberta, Canada

A complete stratigraphic assessment and revision of the middle Campanian to upper Maastrichtian Wapiti Formation in north-western Alberta and north-eastern British Columbia is the main aim of this research project. The study area encompasses an area of approximately 200X180 km in the Grande Prairie County (west-central Alberta) and easternmost British Columbia, Canada. Results presented here indicate that the 1300m thick succession currently reported in the literature as “undifferentiated lithostratigraphic unit”, consists of five lithostratigraphic units and four unconformity-bounded depositional sequences; their study and description have been documented integrating several geological disciplines, including sequence stratigraphic methods, well-log signatures, facies analysis, and fossil associations. On the whole, particular attention has been given to 1) age and nature of both basal and upper contacts of the Wapiti Formation, 2) effective mappability of lithostratigraphic units and depositional sequences in western Alberta, and 3) the identification of previously undetermined maximum flooding surface of the Bearpaw seaway and Drumheller Marine Tongue, which are reference marine unit in central and southern Alberta. A second, but not less important, guideline for the project has been the rich paleontological record of the Wapiti deposits. Detailed paleoenvironmental and taxonomical information on old and new finds have been the base for correlation with well known associations of Alaska, southern Alberta, and Montana. Newly discovered rich fossil localities documented an extraordinarily diverse fauna during the latest Cretaceous, including dinosaurs, squamates, and fresh-water fishes and reptiles. Lastly, in order to better characterize the Wapiti Formation, major marker beds were described: these include several bentonites (altered volcanic ash deposits) which have been documented over an area of almost 30.000 km2, as well as four major coal zones, characterized by tabular coal seams with an overall thickness of 2 meters. Such marker beds represent a formidable tool for high-resolution chronology and regional correlations within the Late Cretaceous Alberta foreland basin.

Condensational growth of atmospheric aerosol particles in an expanding water saturated air flow

Aerosol particles and water vapour are two important constituents of the atmosphere. Their interaction, i.e. thecondensation of water vapour on particles, brings about the formation of cloud, fog, and raindrops, causing the water cycle on the earth, and being responsible for climate changes. Understanding the roles of water vapour and aerosol particles in this interaction has become an essential part of understanding the atmosphere. In this work, the heterogeneous nucleation on pre-existing aerosol particles by the condensation of water vapour in theflow of a capillary nozzle was investigated. Theoretical and numerical modelling as well as experiments on thiscondensation process were included. Based on reasonable results from the theoretical and numerical modelling, an idea of designing a new nozzle condensation nucleus counter (Nozzle-CNC), that is to utilise the capillary nozzle to create an expanding water saturated air flow, was then put forward and various experiments were carried out with this Nozzle-CNC under different experimental conditions. Firstly, the air stream in the long capillary nozzle with inner diameter of 1.0~mm was modelled as a steady, compressible and heat-conducting turbulence flow by CFX-FLOW3D computational program. An adiabatic and isentropic cooling in the nozzle was found. A supersaturation in the nozzle can be created if the inlet flow is water saturated, and its value depends principally on flow velocity or flow rate through the nozzle. Secondly, a particle condensational growth model in air stream was developed. An extended Mason's diffusion growthequation with size correction for particles beyond the continuum regime and with the correction for a certain particle Reynolds number in an accelerating state was given. The modelling results show the rapid condensational growth of aerosol particles, especially for fine size particles, in the nozzle stream, which, on the one hand, may induce evident `over-sizing' and `over-numbering' effects in aerosol measurements as nozzle designs are widely employed for producing accelerating and focused aerosol beams in aerosol instruments like optical particle counter (OPC) and aerodynamical particle sizer (APS). It can, on the other hand, be applied in constructing the Nozzle-CNC. Thirdly, based on the optimisation of theoretical and numerical results, the new Nozzle-CNC was built. Under various experimental conditions such as flow rate, ambient temperature, and the fraction of aerosol in the total flow, experiments with this instrument were carried out. An interesting exponential relation between the saturation in the nozzle and the number concentration of atmospheric nuclei, including hygroscopic nuclei (HN), cloud condensation nuclei (CCN), and traditionally measured atmospheric condensation nuclei (CN), was found. This relation differs from the relation for the number concentration of CCN obtained by other researchers. The minimum detectable size of this Nozzle-CNC is 0.04?m. Although further improvements are still needed, this Nozzle-CNC, in comparison with other CNCs, has severaladvantages such as no condensation delay as particles larger than the critical size grow simultaneously, low diffusion losses of particles, little water condensation at the inner wall of the instrument, and adjustable saturation --- therefore the wide counting region, as well as no calibration compared to non-water condensation substances.

Spurenanalyse von Uran und Plutonium sowie Speziationsuntersuchungen an Plutonium mit massenspektrometrischen und kapillarelektrophoretischen Methoden

Die Elemente Uran und Plutonium besitzen seit Entdeckung der Kernspaltung und der technischen Nutzung der Kernenergie eine globale Bedeutung. So trägt Pu hauptsächlich zur Radiotoxizität von abgebrannten Brennelementen bei und erfordert im Falle einer Endlagerung in einer tiefen geologischen Formation einen sicheren Verschluss für bis zu einer Million Jahre. Das Wissen über die vorliegenden chemischen Spezies ist dabei entscheidend für das Verständnis der chemisch-physikalischen Wechselwirkungen im jeweiligen geochemischen System, insbesondere mit dem Wirtsgestein (hier Ton) und den allgegenwärtigen Huminstoffen (hier Fulvinsäure). Längerfristig sind so Vorhersagen über einen Transport des hochradioaktiven Abfalls nach Auslaugung und Austritt aus einem Endlager bis in die Biosphäre möglich. Gerade der Ultraspurenbereich, im Fernfeld eines Endlagers zu erwarten, ist dabei von besonderem Interesse. Darüber hinaus machen nuklearforensische Untersuchungen – in Hinblick auf illegal benutztes Nuklearmaterial, Schmuggel oder Nuklearterrorismus – zur Bestimmung der Herkunft, des Alters oder der Radiotoxizität isotopenselektive Nachweismethoden im Ultraspurenbereich notwendig. Im Rahmen dieser Arbeit wurden hierfür die Resonanzionisationsmassenspektrometrie (RIMS) zur isotopenselektiven Spuren- und Ultraspurenanalyse von U und Pu sowie die Kapillarelektrophorese (CE) gekoppelt an die induktiv gekoppelte Plasma (ICP)-Massenspektrometrie (CE-ICP-MS) zur Speziation von Pu eingesetzt. Für den isotopenselektiven Nachweis von Ultraspurenmengen von Uran mittels RIMS wurden vorbereitende Studien durchgeführt und mehrere zweifach resonante Anregungsleitern mit nicht-resonanter Ionisation untersucht. Eine Effizienz von ca. 10^-10 bei einer Nachweisgrenze von 10^12 Atomen U-238 konnte erzielt werden. In Zusammenarbeit mit dem Institut für Radiochemie, TU München, wurde mittels RIMS die Isotopenzusammensetzung von Plutonium, abgetrennt aus einem panzerbrechenden Urangeschoss aus dem Kosovokonflikt, bestimmt und dieses als Waffenplutonium mit einem Gehalt von 15 pg Pu-239/g Uran identifiziert. Rückschlüsse über Herkunft und Alter des Plutoniums konnten daraus gewonnen werden. Für Studien zur Umweltüberwachung von Plutonium in Rheinland-Pfalz wurden Grund-, Oberflächen- und Klärwasserproben mittels RIMS untersucht. Oberhalb der Nachweisgrenze von ca. 10^7 Atomen Pu-239/500 mL konnte kein signifikanter Gehalt bestimmt werden. Zusätzlich wurden Klärschlammproben untersucht, wobei in einer Probe 5,1*10^7 Atome Pu-239/g gemessen wurde, was auf eine Anreicherung von Pu im Klärschlamm aus großen Wasservolumina hindeuten könnte. Speziationsuntersuchungen von Plutonium in Kontakt mit Fulvinsäure und dem Tonmineral Kaolinit wurden in Hinblick auf die Wechselwirkungen im Umfeld eines nuklearen Endlagers durchgeführt. Die Redoxkinetik von Pu(VI) in Kontakt mit Gorleben-Fulvinsäure zeigt eine mit steigendem pH zunehmend schnellere und vollständige Reduktion und ein vergleichbares Verhalten zur Huminsäure. Für ein Plutoniumgemisch aus allen vier umweltrelevanten Oxidationsstufen in Kontakt mit Gorleben-Fulvinsäure konnte nach ca. 1 Monat Kontaktzeit eine fasst vollständige Reduktion zum tri- und tetravalenten Pu beobachtet werden. Sorptionsuntersuchungen der stabilsten Oxidationsstufe, Pu(IV), in Kontakt mit Kaolinit bei pH = 0 bis 13 im Konzentrationsbereich 10^-7 bis 10^-9 mol/L verdeutlichen das ausgeprägte Sorptionsverhalten von Pu(IV) (ca. 60% bis 90% Sorption) im umweltrelevanten pH-Bereich bei einem Einsetzen der Sorption bei pH = 0 bis 2. Im Rahmen des "Colloid and Radionuclide Retardation" (CRR) Experiments im Felslabor Grimsel, Schweizer Alpen, wurde in Zusammenarbeit mit dem Institut für Nukleare Entsorgung, Karlsruhe, die kolloidgetragene Migration von Pu(IV) in einem Grundwasserstrom durch Scherzonen im Granitgestein unter umweltrelevanten Bedingungen untersucht. Bei Zugabe von im Grundwasser stabilen Bentonitkolloiden – Bentonit wird als ein geeignetes Verschlussmaterial für nukleare Abfälle erforscht – konnte ein erhöhter Transport des Pu(IV) beobachtet werden, der durch Sorption des Pu an die mobilen Kolloide hervorgerufen wird. Zur Speziation von Plutonium im Ultraspurenbereich wurde im Rahmen dieser Arbeit an der Entwicklung der Kopplung der CE mit der sehr sensitiven RIMS gearbeitet. Das Prinzip der offline-Kopplung basiert auf dem Sammeln der zu unterschiedlichen Zeiten am Ende der Kapillare eluierten Oxidationsstufen in einzelnen Fraktionen. Aus jeder Fraktion wird ein eigenes Filament hergestellt und mit RIMS auf seinen Plutoniumgehalt untersucht. Eine erste Validierung der Methode konnte durch Bestimmung der Oxidationsstufenzusammensetzung eines bekannten Gemischs erfolgreich für einen Gehalt von ca. 6*10^9 Atome Pu-239 durchgeführt werden. Dies stellt einen möglichen Zugang zu dem erwarteten Konzentrationsbereich im Fernfeld eines Endlagers dar.

Development of analytical methodologies for iodine species in gaseous and particulate phases of the coastal atmosphere

It has been demonstrated that iodine does have an important influence on atmospheric chemistry, especially the formation of new particles and the enrichment of iodine in marine aerosols. It was pointed out that the most probable chemical species involved in the production or growth of these particles are iodine oxides, produced photochemically from biogenic halocarbon emissions and/or iodine emission from the sea surface. However, the iodine chemistry from gaseous to particulate phase in the coastal atmosphere and the chemical nature of the condensing iodine species are still not understood. A Tenax / Carbotrap adsorption sampling technique and a thermo-desorption / cryo-trap / GC-MS system has been further developed and improved for the volatile organic iodine species in the gas phase. Several iodo-hydrocarbons such as CH3I, C2H5I, CH2ICl, CH2IBr and CH2I2 etc., have been measured in samples from a calibration test gas source (standards), real air samples and samples from seaweeds / macro-algae emission experiments. A denuder sampling technique has been developed to characterise potential precursor compounds of coastal particle formation processes, such as molecular iodine in the gas phase. Starch, TMAH (TetraMethylAmmonium Hydroxide) and TBAH (TetraButylAmmonium Hydroxide) coated denuders were tested for their efficiencies to collect I2 at the inner surface, followed by a TMAH extraction and ICP/MS determination, adding tellurium as an internal standard. The developed method has been proved to be an effective, accurate and suitable process for I2 measurement in the field, with the estimated detection limit of ~0.10 ng∙L-1 for a sampling volume of 15 L. An H2O/TMAH-Extraction-ICP/MS method has been developed for the accurate and sensitive determination of iodine species in tropospheric aerosol particles. The particle samples were collected on cellulose-nitrate filters using conventional filter holders or on cellulose nitrate/tedlar-foils using a 5-stage Berner impactor for size-segregated particle analysis. The water soluble species as IO3- and I- were separated by anion exchanging process after water extraction. Non-water soluble species including iodine oxide and organic iodine were digested and extracted by TMAH. Afterwards the triple samples were analysed by ICP/MS. The detection limit for particulate iodine was determined to be 0.10~0.20 ng•m-3 for sampling volumes of 40~100 m3. The developed methods have been used in two field measurements in May 2002 and September 2003, at and around the Mace Head Atmospheric Research Station (MHARS) located at the west coast of Ireland. Elemental iodine as a precursor of the iodine chemistry in the coastal atmosphere, was determined in the gas phase at a seaweed hot-spot around the MHARS, showing I2 concentrations were in the range of 0~1.6 ng∙L-1 and indicating a positive correlation with the ozone concentration. A seaweed-chamber experiment performed at the field measurement station showed that the I2 emission rate from macro-algae was in the range of 0.019~0.022 ng•min-1•kg-1. During these experiments, nanometer-particle concentrations were obtained from the Scanning Mobility Particle Sizer (SMPS) measurements. Particle number concentrations were found to have a linear correlation with elemental iodine in the gas phase of the seaweeds chamber, showing that gaseous I2 is one of the important precursors of the new particle formation in the coastal atmosphere. Iodine contents in the particle phase were measured in both field campaigns at and around the field measurement station. Total iodine concentrations were found to be in the range of 1.0 ~ 21.0 ng∙m-3 in the PM2.5 samples. A significant correlation between the total iodine concentrations and the nanometer-particle number concentrations was observed. The particulate iodine species analysis indicated that iodide contents are usually higher than those of iodate in all samples, with ratios in the range of 2~5:1. It is possible that those water soluble iodine species are transferred through the sea-air interface into the particle phase. The ratio of water soluble (iodate + iodide) and non-water soluble species (probably iodine oxide and organic iodine compounds) was observed to be in the range of 1:1 to 1:2. It appears that higher concentrated non-water soluble species, as the products of the photolysis from the gas phase into the particle phase, can be obtained in those samples while the nucleation events occur. That supports the idea that iodine chemistry in the coastal boundary layer is linked with new particle formation events. Furthermore, artificial aerosol particles were formed from gaseous iodine sources (e.g. CH2I2) using a laboratory reaction-chamber experiment, in which the reaction constant of the CH2I2 photolysis was calculated to be based upon the first order reaction kinetic. The end products of iodine chemistry in the particle phase were identified and quantified.

Produzione di idrogeno mediante reforming ciclico dell'etanolo

This work deals with a study on the feasibility of a new process, aimed at the production of hydrogen from water and ethanol (a compound obtained starting from biomasses), with inherent separation of hydrogen from C-containing products. The strategy of the process includes a first step, during which a metal oxide is contacted with ethanol at high temperature; during this step, the metal oxide is reduced and the corresponding metallic form develops. During the second step, the reduced metal compound is contacted at high temperature with water, to produce molecular hydrogen and with formation of the original metal oxide. In overall, the combination of the two steps within the cycle process corresponds to ethanol reforming, where however COx and H2 are produced separately. Various mixed metal oxides were used as electrons and ionic oxygen carriers, all of them being characterized by the spinel (inverse) structure typical of Me ferrites: MeFe2O4 (Me=Co, Ni, Fe or Cu). The first step was investigated in depth; it was found that besides the generation of the expected CO, CO2 and H2O, the products of ethanol anaerobic oxidation, also a large amount of H2 and coke were produced. The latter is highly undesired, since it affects the second step, during which water is fed over the pre-reduced spinel at high temperature. The behavior of the different spinels was affected by the nature of the divalent metal cation; magnetite was the oxide showing the slower rate of reduction by ethanol, but on the other hand it was that one which could perform the entire cycle of the process more efficiently. Still the problem of coke formation remains the greater challenge to solve.

Modulation of apoptosis by endogenously produced nitric oxide

Untersuchungen zur Expression der induzierbaren NO-Synthetase (NOS2) belegen eine häufige Expression dieses Enzyms in Tumoren unterschiedlicher Gewebe. Bislang ist jedoch ungeklärt, ob die Expression der NOS2 in Tumorzellen die apoptotische Eliminierung durch zytotoxische T-Zellen beeinflussen kann. In der vorliegenden Arbeit wurden die Folgen einer endogenen NO-Synthese auf die Apoptosesensitivität von HEK293-Zellen untersucht. Um primäre NO-Wirkungen von NO-induzierten, sekundären (kompensatorischen) Veränderungen zu trennen, wurde mit einem induzierbaren Vektorsystem gearbeitet. Die NOS2 wurde zunächst unter der Kontrolle eines Ecdyson-sensitiven Promoters in HEK293-Zellen kloniert. Es konnten regulierbare NOS2-Klone selektiert werden, die nach Ponasteronbehandlung dosisabhängig die NOS2 exprimieren und NO synthetisieren. Die NOS2-Expression wurde durch Western Blot Analyse und Immunfluoreszenzfärbung dargestellt und die NO-Produktion mit Hilfe der Griess-Reaktion gemessen. An den NOS2-induzierten Zellen wurde dann der Einfluss von NO auf die CD95-vermittelte Apoptose analysiert. Es zeigte sich nach Stimulation des CD95-Rezeptors eine deutliche Korrelation der Apoptoserate mit der NOS2-Expression. In Kokulturexperimenten mit Peptid-spezifischen zytotoxischen T-Zellen zeigte sich, dass NO-produzierende Zielzellen effektiver eliminiert werden konnten. Auch nach Behandlung der Zellen mit TRAIL ergab sich eine höhere Apoptoserate in NO-produzierenden Zellen. Die weitere Analyse der durch NO beeinflussten Signalwege ergab eine Beteiligung von ER-Stress-vermittelten Apoptosewegen. Dies zeigte sich an der Hochregulation des ER-Stress-Proteins Grp78 (BiP) nach NOS2-Expression und der Spaltung der am ER-lokalisierten Caspase-4. Darüber hinaus konnte der schnellere Verlust des mitochondrialen Membranpotentials in Abhängigkeit von der NOS2-Expression nachgewiesen werden. Weiterhin wurde die Wirkung einer dauerhaften NO-Exposition auf die Apoptosesensitivität der Zellen untersucht. Auch ohne zusätzliche CD95-Stimulation induzierte eine kontinuierliche NOS2-Expression nach wenigen Tagen in den EcR293-NOS2-Zellen Apoptose. Diese Dauerbehandlung führte zum nahezu vollständigen Absterben der Kulturen. Einige Zellen überlebten jedoch diese Behandlung und wuchsen zu Zellklonen. Diese NO-resistenten Klone konnten isoliert werden. Sie zeigten eine zusätzliche Resistenz für CD95-vermittelte Apoptosesignale und waren besser vor dem Angriff Peptid-spezifischer CTLs geschützt. Die Apoptoseresistenz blieb auch nach längerer Kultur erhalten und scheint auf NO-induzierter Genotoxizität zu beruhen. Anhand dieser Arbeit konnte gezeigt werden, dass allein durch chronische NO-Behandlung eine Selektion apoptoseresistenter Zellen stattfinden kann.

Detailed analyses of mutations affecting structural formation of neuromuscular synapses in Drosophila melanogaster

The establishment of appropriate synapses between neurons and their target cells is an essential requirement for the formation of functional neuronal circuits. However, there is very little insight into the mechanisms underlying de novo formation of synapses and synaptic terminals. To identify novel genes involved in signalling or structural aspects of these processes I capitalised on possibilities provided by the model organism Drosophila. Thus, I contributed to a screen of a collection of third chromosomal mutations (Salzberg et al., 1997, Genetics 147, 1723ff.) selecting those mutant strains displaying structural defects of Drosophila neuromuscular junctions (NMJ). Carrying out genetic mapping experiments, I could assign 7 genes to interesting candidate mutations. All 7 mutations selected in this process cause size alterations of the embryonic NMJ, and one shows additional disturbances in the distribution of synaptic markers. 4 of these turned out to be transcription factors, not falling into the remit of this project. Only for one of these, the neuronal transcription factor Castor, I could show that its overgrown mutant NMJ phenotype is due to an increase in the number of motorneurons. The remaining genes encode a potential nitrophenylphosphatase, the translation initiation factor eIF4AIII, and a novel protein Waharan. Unfortunately, the nitophenylphosphatase gene was identified too late to carry out functional studies in the context of this project, but potential roles are discussed. eIF4AIII promotes NMJ size tempting to speculate that local translation at the NMJ is affected. I found that the synaptic scaffolding molecule Discs large (Dlg; orthologue of PSD95) is upregulated at eIF4AIII mutant NMJs. Targeted upregulation of Dlg can not mimic the eIF4AIII mutant phenotype, but dlg mutations suppress it. Therefore, Dlg function is required but not sufficient in this context. My findings are discussed in detail, pointing out future directions. The main focus of this work is the completely novel gene waharan (wah), an orthologue of the human gene KIAA1267 encoding a big brain protein of likewise unknown structure and function. My studies show that mutations or RNAi knock-down of wah cause NMJ overgrowth and reveal additional crucial roles in the patterning of wing imginal discs. RNAi studies suggest Wah to be required pre- and postsynaptically at NMJs and, consistently, wah is transcribed in the nervous system and muscles. Anti-Wah antisera were produced but could no longer be tested here, but preliminary studies with newly generated HA-targeted constructs suggest that Wah localises at NMJs and in neuronal nuclei. In silico analyses predict Wah to be structurally related to the Rad23-family of proteins, likely to target ubiquitinated proteins to the proteasome for degradation (Chen et al., 2002, Mol Cell Biol 22, 4902ff.) . In agreement with this prediction, poly-ubiquitinated proteins were found to accumulate in the absence of wah function, and wah-like mutant phenotypes were induced in NMJs and wing discs by knocking down proteasome function. My analysis further revealed that poly-ubiquitinated proteins are reduced in nuclei of wah mutant neurons and muscles, suggesting that Wah may play additional roles in ubiquitin-mediated nuclear import. Taken together, this study has uncovered a number of interesting candidate genes required for the de novo formation of Drosophila NMJs. 3 of these genes fell into the focus of this project. As discussed in detail, discovery of these genes and insights gained into their function have high potential to be translatable into vertebrate systems.