Effect of substrate temperature on the physical properties of dc magnetron sputtered CuAlO2 films

Copper aluminum oxide films were prepared by direct current (dc) reactive magnetron sputtering under various substrate temperatures in the range of 303–648 K and systematically studied their physical properties. The physical properties of the films were strongly affected by the substrate temperature. The films formed at substrate temperatures <373 K were amorphous while those deposited at higher substrate temperatures (≥373 K) were polycrystalline in nature. The electrical properties of the films enhanced with substrate temperature due to the improved crystallinity. The Hall mobility of 9.4 cm2/V s and carrier concentration of 3.5 × 1017 cm−3 were obtained at the substrate temperature of 573 K. The optical band gap of the films decreased from 3.87 to 3.46 eV with the increase of substrate temperature from 373 to 573 K.

Rationale of Length Scale-Down Model Span Testing of Transmission Lines

Length scale-down (LS) model tests have been traditionally employed for laboratory studies on aeolian vibration of transmission line conductors. The span adopted is normally 30 m and is recommended by the relevant Indian, as well as other, standards. The traditionally adopted length of the LS model is reexamined herein to establish the rationale behind the choice. Based on the theoretical studies discussed, certain guidelines for the choice of model span of conductor are emphasized. In addition, the adequacy of the LS span as a tool for predicting the performance of the full span is reestablished.

Odour sampling 1: Physical chemistry considerations

The selection of an odour sampling device may influence the composition of the resulting odour sample. Limited comparison of emission rates derived from turbulent and essentially quiescent sampling devices confirms that the emission rates derived from these devices are quite different. There is therefore compelling evidence that current odour sampling practice should have greater regard for fundamental physical and chemical principles, the nature of the odour source and the conditions created by the sampling device. Such consideration may identify the most appropriate situations under which the use of these devices may or may not be correct.

Odour sampling. 2. Comparison of physical and aerodynamic characteristics of sampling devices: A review

Sampling devices differing greatly in shape, size and operating condition have been used to collect air samples to determine rates of emission of volatile substances, including odour. However, physical chemistry principles, in particular the partitioning of volatile substances between two phases as explained by Henrys Law and the relationship between wind velocity and emission rate, suggests that different devices cannot be expected to provide equivalent emission rate estimates. Thus several problems are associated with the use of static and dynamic emission chambers, but the more turbulent devices such as wind tunnels do not appear to be subject to these problems. In general, the ability to relate emission rate estimates obtained from wind tunnel measurements to those derived from device-independent techniques supports the use of wind tunnels to determine emission rates that can be used as input data for dispersion models.

Fusion of worlds?: Consumers' self-narrative in a hybrid digital/physical world

As the Internet becomes deeply embedded in consumers' life and continuously accessed through mobile devices, the boundary between the digital and the physical becomes less defined. This thesis investigates how this blurring boundary impacts on consumers' construction of their self-narrative and found that consumers' narrative is paradoxically coherent and fragmented and depicts a heroic story of the self. Prior studies show consumers achieve their desired life story through meaningful consumption, however, the notion of fragmented lives are challenged. Further, extensive digital leisure consumption is often viewed in a less positive light. Nevertheless, consumers, who significantly consume digital leisure, do not disregard their physical world or favour one space over the other. Rather, they negotiate key aspects from their digital and physical lives and fluidly move between these two worlds, creating a hybrid narrative that saves their self and others.

Weight bearing physical activity for performance and bone health in prepubertal girls

This study assessed the status of bone and cardiovascular health in young, prepubertal females (aged 9 to 11 years) during a school based intervention program involving weight bearing physical activity. A study of 10 months duration was conducted in four primary schools in the Melbourne suburbs. It involved a physical activity group (n=38) and an aged-matched control group (n=33). Baseline data including pubertal status, health-related fitness, bone mass and body composition were obtained pre and post the intervention programme. All children had their bone mineral density monitored. Bone mineral density and body composition measurements were performed by DXA using the Hologic QDR 2000 bone densitometer. At the completion of the program the activity group had accrued significantly greater bone mass at total body, lumbar spine, leg and femoral neck when expressed as BMC or BMD.

Testing insecticides against Phthorimaea operculella (Zeller) (Lepidoptera: Gelechiidae) using a tomato plant bioassay

A bioassay technique was developed to test the efficacy of insecticides against potato moth (Phthorimaea operculella (Zeller)) on tomatoes. The technique tested efficacy against both larvae in mines and neonate larvae that had not yet penetrated the leaf, and explained the failure of some insecticides to control P. operculella infestations in commercial tomato crops. Neonate larvae placed on leaves of potted plants several days before treatment provided larvae for testing of insecticides against larvae in mines; other neonates were placed on leaves after treatment to test efficacy against larvae yet to penetrate the leaf. The plants were sprayed with the candidate insecticides, held for 5-7 days, and larval mortality assessed. Chlorfenapyr (100, 200 g a.i. ha-1) and abamectin (8.1 g a.i. ha-1) were effective against neonate larvae and larvae in mines. Sulprofos (720 g a.i. ha -1), methomyl (450 g a.i. ha-1) and spinosad (96 g a.i. ha-1) were effective against neonate larvae but not against larvae in mines. Methamidophos (1102 g a.i. ha-1), endosulfan (700 g a.i. ha-1) and Bacillus thuringiensis kurstaki (1000 g ha-1) had some effect against exposed larvae but little against larvae in mines. Thiodicarb (525 g a.i. ha-1), azinphos-ethyl (440 g a.i. ha -1), imidacloprid (59.5 g a.i. ha-1), hexaflumuron (50 g a.i. ha-1), methoxyfenozide (300 g a.i. ha-1) and tebufenozide (200 g a.i. ha-1) were ineffective. A field trial using chlorfenapyr (25, 50, 100, 150 and 200 g a.i. ha-1) and methamidophos (1102 g a.i. ha-1) validated the bioassay technique, with chlorfenapyr effective in reducing the numbers of larvae in mines in leaves.

Testing the simulation capability of APSIM-ORYZA under different levels of nitrogen fertiliser and transplanting time regimes in Korea

APSIM-ORYZA is a new functionality developed in the APSIM framework to simulate rice production while addressing management issues such as fertilisation and transplanting, which are particularly important in Korean agriculture. To validate the model for Korean rice varieties and field conditions, the measured yields and flowering times from three field experiments conducted by the Gyeonggi Agricultural Research and Extension Services (GARES) in Korea were compared against the simulated outputs for different management practices and rice varieties. Simulated yields of early-, mid- and mid-to-late-maturing varieties of rice grown in a continuous rice cropping system from 1997 to 2004 showed close agreement with the measured data. Similar results were also found for yields simulated under seven levels of nitrogen application. When different transplanting times were modelled, simulated flowering times ranged from within 3 days of the measured values for the early-maturing varieties, to up to 9 days after the measured dates for the mid- and especially mid-to-late-maturing varieties. This was associated with highly variable simulated yields which correlated poorly with the measured data. This suggests the need to accurately calibrate the photoperiod sensitivity parameters of the model for the photoperiod-sensitive rice varieties in Korea.

Social and physical environments in senior communities: The Finnish experience

Purpose – The purpose of this paper is to discuss residents’ views of social and physical environments in a co-housing and in a senior housing setting in Finland. Also, the study aims to point out important connections between well-being and built environment. Design/methodology/approach – The data include interviews and survey responses gathered in the cases. The results and analysis are presented at different case study levels, with the discussion and conclusions following this. Findings – The findings show that the physical environment and common areas have an important role to activate residents. When well-designed common areas exist, a higher level of engagement can be achieved by getting residents involved in the planning and running of activities. Research limitations/implications – This paper discusses residents’ experiences in two Finnish housing settings and it focuses on the housing market in Finland. Practical implications – The findings encourage investors and housing operators to design and invest common areas which could activate residents and create social contacts. Also, investors have to pay attention to the way these developments are managed. Originality/value – This study is the first to investigate the Finnish co-housing setting and compare social and physical environments in a co-housing and a senior house.

Development and testing of an evaluation procedure for commercial manure additive products.

Manure additive products can be used to reduce odour emissions (OE) from livestock farms. The standardised evaluation of these manure additive products under specific farm conditions is important. In this study, the efficacy of a manure additive (WonderTreat(TM), CKLS, Inc., Hong-Kong) was assessed under Australian conditions utilising a combination of laboratory and field-scale evaluation techniques. As a first step, the efficacy of the manure additive was assessed in a laboratory-scale trial using a series of uniformly managed digesters and standard odour, liquor ammonia and hydrogen sulphide concentration measurement procedures. This showed that the addition of WonderTreat(TM) at the 'low dose rate' (LDR) (102.6 g m-2) used during the trial significantly, but only marginally (30%; P = 0.02) reduced the OE rate (mean 13.9 OU m-2 s-1) of anaerobic pig liquor relative to an untreated control (UC) (19.9 OU m-2 s-1). However, the 'high dose rate' (HDR) (205.3 g m-2) also assessed during the trial preformed similarly (19.7 OU m-2 s-1) to the UC. No statistically significant difference in the concentrations of a range of measured water quality variables at the 5% level was observed between the treatments or controls digesters. As a second step, a field-scale assessment of the manure additive was undertaken at a commercial piggery. Two piggery manure lagoons (each with approximately 2500 m2 surface area) were included in the study; one was treated with WonderTreat(TM) while the other was used as control. The efficacy of the treatment was assessed using olfactometric evaluation of odour samples collected from the surface of the pond using a dynamic wind tunnel and ancillary equipment. No statistically significant reduction in OE rate could be demonstrated (P = 0.35), partially due to the limited number of samples taken during the assessment. However, there was a numerical reduction in the average OE rate of the treatment pond (29 OU m-2 s-1 at 1 m s-1) compared to the control lagoon (38 OU m-2 s-1 at 1 m s-1).

Hardness Methods for Testing Maize Kernels

Maize is a highly important crop to many countries around the world, through the sale of the maize crop to domestic processors and subsequent production of maize products and also provides a staple food to subsistance farms in undeveloped countries. In many countries, there have been long-term research efforts to develop a suitable hardness method that could assist the maize industry in improving efficiency in processing as well as possibly providing a quality specification for maize growers, which could attract a premium. This paper focuses specifically on hardness and reviews a number of methodologies as well as important biochemical aspects of maize that contribute to maize hardness used internationally. Numerous foods are produced from maize, and hardness has been described as having an impact on food quality. However, the basis of hardness and measurement of hardness are very general and would apply to any use of maize from any country. From the published literature, it would appear that one of the simpler methods used to measure hardness is a grinding step followed by a sieving step, using multiple sieve sizes. This would allow the range in hardness within a sample as well as average particle size and/or coarse/fine ratio to be calculated. Any of these parameters could easily be used as reference values for the development of near-infrared (NIR) spectroscopy calibrations. The development of precise NIR calibrations will provide an excellent tool for breeders, handlers, and processors to deliver specific cultivars in the case of growers and bulk loads in the case of handlers, thereby ensuring the most efficient use of maize by domestic and international processors. This paper also considers previous research describing the biochemical aspects of maize that have been related to maize hardness. Both starch and protein affect hardness, with most research focusing on the storage proteins (zeins). Both the content and composition of the zein fractions affect hardness. Genotypes and growing environment influence the final protein and starch content and. to a lesser extent, composition. However, hardness is a highly heritable trait and, hence, when a desirable level of hardness is finally agreed upon, the breeders will quickly be able to produce material with the hardness levels required by the industry.

Podcast: Community wide interventions for increasing physical activity

If the amount of physical activity in a society increased, it should improve public health; but uncertainties remain about how to achieve this. Professor Philip Baker from the Queensland University of Technology in Australia describes the findings from the January 2015 update of the Cochrane review of the evidence on community-wide interventions.

#20 [updated] Community wide interventions for increasing physical activity - Clinical Version

People who are physically active have higher levels of health related fitness, and a lower risk profile for developing a number of disabling medical conditions and chronic diseases. However, despite considerable evidence of the benefits of regular physical activity, global levels of physical inactivity remain stubbornly high. In response, governments are looking to find ways to increase the physical activity of their populations.

New approach to improved detection and tracking performance in track-while-scan radars. Part 3: Performance prediction, optimisation and testing

The paper presents, in three parts, a new approach to improve the detection and tracking performance of a track-while-scan radar. Part 1 presents a review of the current status of the subject. Part 2 details the new approach. It shows how a priori information provided by the tracker can be used to improve detection. It also presents a new multitarget tracking algorithm. In the present Part, analytical derivations are presented for assessing, a priori, the performance of the TWS radar system. True track initiation, false track initiation, true track continuation and false track deletion characteristics have been studied. It indicates how the various thresholds can be chosen by the designer to optimise performance. Simulation results are also presented.