Desenvolvimento de argamassa para restauração utilizando resíduo do polimento do porcelanato

The coatings mortars are essential elements of building structures because they execute an important role in protecting walls and are particularly exposed to aggressive action responsible for its degradation over time. The importance of wall coverings has been the subject of discussion and analysis in the conservation and rehabilitation of old buildings. Are sometimes removed and replaced with inappropriate solutions of constructive point of view or architecture. The most commonly used coatings on walls of old buildings is based on traditional hydraulic lime mortars. The present study aims at the formulation of new lime- based mortars and aerial fine aggregate, in order to contribute to a better field of conservation and restoration mortar coating of old buildings. Residue was used for polishing porcelain as fine aggregate, replacing the aggregate (sand), in percentages 05-30% by mass. We conducted a thorough evaluation of the mortar properties in fresh and hardened state by comparing the performance of the same with a reference mortar. The residue used was characterized as the density, bulk density, and particle size laser, scanning electron microscopy, X-ray diffraction and X-ray fluorescence. Formulations were produced 7, 6 with residue and one commonly used formulation, which served as a reference. In the formulations of lime mortars air (hydrated lime powder CH-I) has been adopted a stroke volume (1:3) with constant binder, was varied and the water / binder and aggregate and waste. For evaluation of mortars fresh, proceeded to consistency analysis, specific gravity, water retention and air content embedded. In the hardened state assays were performed in specific gravity, water retention, modulus of elasticity, tensile strength in bending, compressive strength, water absorption by capillary action, adhesion, tensile strength, resistance to shrinkage and salts by of crystallization trials with resources chloride solution, nitrate and sulfate all sodium in prismatic at 90 days of age, in addition to the micro structural analysis of mortars. Based on the results we can see that the mortar formulated with 10% content of waste and the reference free retraction feature more stable closer to neutrality. The composition of 10% was obtained better performance against the action of the salt crystallization. The mortar with 15% residue obtained better density, lower air content embedded and high capacity for water retention developing good workability. The replacement of 20% of waste generates a satisfactory utilization of resistance to compression, flexion and traction grip the base. And, finally, it can be seen that the mortar with 10, 15 and 20% residual show, in principle, good suitability as coatings, thus enabling a final result consistent with durability, workability and aesthetics developing therefore a material with better performance to repair or replace existing mortars in old buildings

Nonpreference of whitefly for oviposition in tomato genotypes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Tipos de tricomas em genótipos de Lycopersicon

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo in vitro da habilidade predatória de monacrosporium robustum sobre heterodera glycines

O fungo nematófago Monacrosporium robustum foi detectado, isolado e identificado pela primeira vez de solos do Brasil, em maio de 1999, no Laboratório de Nematologia do Departamento de Fitossanidade da Universidade Estadual Paulista (UNESP), Campus de Jaboticabal, São Paulo, tendo sido o potencial como agente de biocontrole do nematóide de cisto da soja, Heterodera glycines raça 3 observado ao microscópio eletrônico de varredura (MEV) (Maia & Santos, 1999). Na presente pesquisa, detalhes das estruturas de captura, tamanho, forma e septação dos conídios, bem como nematóides capturados pelo fungo foram documentados. Monacrosporium robustum produz micélio hialino, e as estruturas de captura são constituídas por ramificações adesivas, na forma de protuberâncias verticais que surgem das hifas, medindo, em média, 10 µm de comprimento e 5 µm de diâmetro. Uma substância gelatinosa desprende- se dessas estruturas, ao contato com o nematóide, aprisionando-o. Os conídios do fungo são hialinos, fusóides com dois ou quatro septos, às vezes, cinco. Conídios jovens são asseptados e piriformes. Sob condições de laboratório, esse fungo predou 100% dos ovos e dos juvenis de segundo estádio de H. glycines e formas ativas de Panagrellus sp., no período de 72 h da exposição desses nematóides ao fungo.

Aspectos biológicos do ácaro Brevipalpus phoenicis vetor da leprose dos citros em plantas de buva (Conyza canadensis)

O ácaro Brevipalpus phoenicis, vetor da leprose dos citros, é uma espécie polífaga que tem ampla gama de hospedeiros alternativos nos pomares cítricos, nos quais se pode manter e/ou incrementar suas populações. O objetivo deste trabalho foi estudar a sobrevivência, a oviposição e o modo de alimentação do ácaro B. phoenicis em plantas de buva (Conyza canadensis) com diferentes tamanhos. Para avaliação da sobrevivência e oviposição do ácaro B. phoenicis, foi utilizado o delineamento estatístico inteiramente casualizado, com cinco tratamentos e doze repetições. Os tratamentos estudados foram: (1) secções de caules de plantas menores que 20 cm, (2) entre 21 e 50 cm, (3) entre 51 e 100 cm e (4) maiores que 101 cm de altura; e (5) secções de ramos de laranja. Dez fêmeas adultas de B. phoenicis, procedentes de uma criação-estoque, foram transferidas para cada secção de caule de buva e ramos de citros como testemunha. Avaliou-se a sobrevivência e a oviposição dos ácaros até 120 horas após a transferência. Alguns aspectos comportamentais do ácaro B. phoenicis foram fotomicrografados, utilizando-se microscópico eletrônico de varredura. Verificou-se que as plantas de maior altura de buva foram mais favoráveis à sobrevivência do ácaro B. phoenicis do que as de menor tamanho. Contudo, a quantidade de ovos postos pelo ácaro não diferiu em relação à altura das plantas de buva. Com base nas fotomicrografias, constatou-se a preferência do ácaro B. phoenicis por se alimentar na base dos tricomas presentes na superfície do caule da planta de buva, justificado, possivelmente, pela maior turgescência das células encontradas nessa região da planta. Esses resultados reforçam a importância do manejo de buva nos pomares cítricos, pois a sua presença no campo pode favorecer a sobrevivência e o desenvolvimento do ácaro B. phoenicis, servindo, portanto, como hospedeira alternativa, o que pode contribuir para a disseminação do ácaro e, consequentemente, da leprose nos pomares cítricos.

Morphological description of Amblyomma brasiliense Aragão, 1908 (Acari: Ixodidae) larvae and nymphs

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência do envelhecimento acelerado na anatomia da testa de sementes de soja, cv. Monsoy 8400

Durante o processo de envelhecimento, as sementes sofrem alterações degenerativas que influenciam o seu potencial fisiológico. Entre estas alterações podem estar as modificações anatômicas nas camadas celulares da testa da semente. Objetivou-se, com este trabalho, verificar a relação entre a anatomia da testa de sementes de soja, cultivar Monsoy 8400 e a germinação, após o envelhecimento acelerado, pelo fato da testa apresentar um papel fundamental na conservação do potencial fisiológico das sementes. As sementes foram envelhecidas a 42ºC e 100% UR do ar por períodos de zero, 24, 48, 72 e 96 horas. Avaliaram-se os teores de água e a germinação, posteriormente à secagem, seções transversais da testa de 10 sementes de cada tratamento foram eletromicrografadas, com microscópio eletrônico de varredura,,observando-se as camadas das células paliçádicas, ampulhetas e parenquimáticas A germinação declinou com o aumento dos períodos de envelhecimento. Houve redução da espessura das camadas da testa nos períodos de 48, 72 e 96 horas deste processo. Observou-se que, principalmente, para os períodos de envelhecimento de 72 e 96 horas, que as células da camada hipodérmica apresentaram um aspecto de colapso, sendo este acentuado para o período de 96 horas. A redução da espessura das camadas sugere a ocorrência de um colapso das células que compõem tais camadas, sendo um fator causador da redução do potencial germinativo.

Seed anatomy and germination of Phoenix roebelenii O'Brien (Arecaceae)

O objetivo desse trabalho foi estudar a morfologia, anatomia e o processo germinativo de sementes de Phoenix roebelenii. Para o levantamento dos dados biométricos foram utilizadas 100 sementes de frutos recém-colhidos, deixados secar ao ar por um dia. Para a germinação, quatro repetições de 50 sementes tratadas com Vitavax-Thiran foram semeadas em bandejas de plástico, contendo Sphagnum sp. como substrato e mantidas sob condições ambientais de laboratório. Detalhes da morfologia da semente foram documentados com o uso de microscopia eletrônica de varredura e esquematizados com auxílio de câmara clara, acoplada ao estereomicroscópio. Foram confeccionadas lâminas permanentes com cortes do embrião, para o estudo de sua anatomia. As dimensões médias das sementes foram: 10,32mm comprimento, 5,21mm largura e 3,91mm espessura. O peso de 1000 sementes foi de 151,1g e 1kg continha 6600 unidades. O início da germinação variou entre 27 e 58 dias. As sementes são albuminosas, com endosperma duro e o embrião é pouco diferenciado, lateral e periférico. A germinação inicia-se pela abertura de um opérculo, através do qual é emitido o pecíolo cotiledonar com o eixo embrionário na extremidade. O pecíolo funciona, internamente, como um haustório, digerindo gradativamente o endosperma. Na sua parte posterior, desenvolve-se a plúmula, que emerge através de uma fenda. Nota-se o aparecimento de raízes secundárias na porção anterior da raiz primária.

Anodização para obtenção de membranas cerâmicas

This a study on the achievement of alumina membranes by the method of anodizing. From this method got up a layer of aluminum oxide on the anodic metal, who presented the basic properties necessary for the application as a support for the production and acquisition of nanomaterials, such as porosity nano and resistance to high temperature, and other properties, as resistance to corrosion, and chemical, high ranking of the structure and pore size of the pores. The latter, ranging from 10 to 100nm depended on the electrolyte used, which in this study was the H2SO4. To remove all remaining aluminum, it is a bath of dissolution with HCl and CuCl where the residual aluminum has been withdrawn, and the deep pores were opened after chemical treatment with NaOH. After the dissolution, the membranes were calcined at temperatures of 300, 600 and 900° C, and sintered at temperatures of 1200 and 1300º C to win mechanical strength, porosity and observe the desired crystallization. Then went through analyses of composition through X-ray diffraction and morphology of the microstructure through a scanning electron microscope. The method was effective for obtaining alumine membranes applied in the processes of production of materials in nano

Biomecânica e otimização topológica com H-adaptatividade em implantes dentários nitretados a plasma em cátodo oco

In recent years there has been a significant growth in technologies that modify implant surfaces, reducing healing time and allowing their successful use in areas with low bone density. One of the most widely used techniques is plasma nitration, applied with excellent results in titanium and its alloys, with greater frequency in the manufacture of hip, ankle and shoulder implants. However, its use in dental implants is very limited due to high process temperatures (between 700 C o and 800 C o ), resulting in distortions in these geometrically complex and highly precise components. The aim of the present study is to assess osseointegration and mechanical strength of grade II nitrided titanium samples, through configuration of hollow cathode discharge. Moreover, new formulations are proposed to determine the optimum structural topology of the dental implant under study, in order to perfect its shape, make it efficient, competitive and with high definition. In the nitriding process, the samples were treated at a temperature of 450 C o and pressure of 150 Pa , during 1 hour of treatment. This condition was selected because it obtains the best wettability results in previous studies, where different pressure, temperature and time conditions were systematized. The samples were characterized by X-ray diffraction, scanning electron microscope, roughness, microhardness and wettability. Biomechanical fatigue tests were then conducted. Finally, a formulation using the three dimensional structural topology optimization method was proposed, in conjunction with an hadaptive refinement process. The results showed that plasma nitriding, using the hollow cathode discharge technique, caused changes in the surface texture of test specimens, increases surface roughness, wettability and microhardness when compared to the untreated sample. In the biomechanical fatigue test, the treated implant showed no flaws, after five million cycles, at a maximum fatigue load of 84.46 N. The results of the topological optimization process showed well-defined optimized layouts of the dental implant, with a clear distribution of material and a defined edge

Metodologia de análise e diagnóstico de fratura em um componente automotivo sujeito a cargas cíclicas alternadas

The competitiveness of the trade generated by the higher availability of products with lower quality and cost promoted a new reality of industrial production with small clearances. Track deviations at the production are not discarded, uncertainties can statistically occur. The world consumer and the Brazilian one are supported by the consumer protection code, in lawsuits against the products poor quality. An automobile is composed of various systems and thousands of constituent parts, increasing the likelihood of failure. The dynamic and security systems are critical in relation to the consequences of possible failures. The investigation of the failure gives us the possibility of learning and contributing to various improvements. Our main purpose in this work is to develop a systematic, specific methodology by investigating the root cause of the flaw occurred on an axle end of the front suspension of an automobile, and to perform comparative data analyses between the fractured part and the project information. Our research was based on a flaw generated in an automotive suspension system involved in a mechanical judicial cause, resulting in property and personal damages. In the investigations concerning the analysis of mechanical flaws, knowledge on materials engineering plays a crucial role in the process, since it enables applying techniques for characterizing materials, relating the technical attributes required from a respective part with its structure of manufacturing material, thus providing a greater scientific contribution to the work. The specific methodology developed follows its own flowchart. In the early phase, the data in the records and information on the involved ones were collected. The following laboratory analyses were performed: macrography of the fracture, micrography with SEM (Scanning Electron Microscope) of the initial and final fracture, phase analysis with optical microscopy, Brinell hardness and Vickers microhardness analyses, quantitative and qualitative chemical analysis, by using X-ray fluorescence and optical spectroscopy for carbon analysis, qualitative study on the state of tension was done. Field data were also collected. In the analyses data of the values resulting from the fractured stock parts and the design values were compared. After the investigation, one concluded that: the developed methodology systematized the investigation and enabled crossing data, thus minimizing diagnostic error probability, the morphology of the fracture indicates failure by the fatigue mechanism in a geometrically propitious location, a tension hub, the part was subjected to low tensions by the sectional area of the final fracture, the manufacturing material of the fractured part has low ductility, the component fractured in an earlier moment than the one recommended by the manufacturer, the percentages of C, Si, Mn and Cr of the fractured part present values which differ from the design ones, the hardness value of the superior limit of the fractured part is higher than that of the design, and there is no manufacturing uniformity between stock and fractured part. The work will contribute to optimizing the guidance of the actions in a mechanical engineering judicial expertise

Fresamento com ar quente: uma proposta para minimizar a formação de trincas térmicas em ferramentas de metal duro

This work presents the results, analyses and conclusions about a study carried out with objective of minimizing the thermal cracks formation on cemented carbide inserts during face milling. The main focus of investigation was based on the observation that milling process is an interrupted machining process, which imposes cyclic thermal loads to the cutting tool, causing frequent stresses changes in its superficial and sub-superficial layers. These characteristics cause the formation of perpendicular cracks from cutting edge which aid the cutting tool wear, reducing its life. Several works on this subject emphasizing the thermal cyclic behavior imposed by the milling process as the main responsible for thermal cracks formation have been published. In these cases, the phenomenon appears as a consequence of the difference in temperature experienced by the cutting tool with each rotation of the cutter, usually defined as the difference between the temperatures in the cutting tool wedge at the end of the cutting and idle periods (T factor). Thus, a technique to minimize this cyclic behavior with objective of transforming the milling in an almost-continuous process in terms of temperature was proposed. In this case, a hot air stream was applied into the idle period, during the machining process. This procedure aimed to minimize the T factor. This technique was applied using three values of temperature from the hot air stream (100, 350 e 580 oC) with no cutting fluid (dry condition) and with cutting fluid mist (wet condition) using the hot air stream at 580oC. Besides, trials at room temperature were carried out. Afterwards the inserts were analyzed using a scanning electron microscope, where the quantity of thermal cracks generated in each condition, the wear and others damages was analyzed. In a general way, it was found that the heating of the idle period was positive for reducing the number of thermal cracks during face milling with cemented carbide inserts. Further, the cutting fluid mist application was effective in reducing the wear of the cutting tools.

Mecanismos de desgaste de poliuretano em ensaios de microabrasão

Wear mechanisms and thermal history of two non-conforming sliding surfaces was investigated in laboratory. A micro-abrasion testing setup was used but the traditional rotative sphere method was substituted by a cylindrical surface of revolution which included seven sharp angles varying between 15o to 180o. The micro-abrasion tests lead to the investigation on the polyurethane response at different contact pressures. For these turned counterfaces with and without heat treatment. Normal load and sliding speeds were changed. The sliding distance was fixed at 5 km in each test. The room and contact temperatures were measured during the tests. The polyurethane was characterized using tensile testing, hardness Shore A measurement, Thermogravimetric Analysis (TGA), Differential Scanning Calorimetry (DSC) and Thermomechanical Analyze (TMA). The Vickers micro-hardness of the steel was measured before and after the heat treatment and the metallographic characterization was also carried out. Worn surface of polyurethane was analysed using Scanning Electron Microscope (SEM) and EDS (Electron Diffraction Scanning) microanalyses. Single pass scratch testing in polyurethane using indenters with different contact angles was also carried out. The scar morphology of the wear, the wear mechanism and the thermal response were analyzed in order to correlate the conditions imposed by the pressure-velocity pair to the materials in contact. Eight different wear mechanisms were identified on the polyurethane surface. It was found correlation between the temperature variation and the wear scar morphology.

Predição de sombras de edifícios sobre vias urbanas com base em modelos digitais de elevações e dados de imagens aéreas de alta resolução

This research presents a methodology for prediction of building shadows cast on urban roads existing on high-resolution aerial imagery. Shadow elements can be used in the modeling of contextual information, whose use has become more and more common in image analysis complex processes. The proposed methodology consists in three sequential steps. First, the building roof contours are manually extracted from an intensity image generated by the transformation of a digital elevation model (DEM) obtained from airborne laser scanning data. In similarly, the roadside contours are extracted, now from the radiometric information of the laser scanning data. Second, the roof contour polygons are projected onto the adjacent roads by using the parallel projection straight lines, whose directions are computed from the solar ephemeris, which depends on the aerial image acquisition time. Finally, parts of shadow polygons that are free from building perspective obstructions are determined, given rise to new shadow polygons. The results obtained in the experimental evaluation of the methodology showed that the method works properly, since it allowed the prediction of shadow in high-resolution imagery with high accuracy and reliability.

Morphological study of the thorax of the five nymphal instars of Triatoma arthurneivai Lent & Martins (Hemiptera, Reduviidae, Triatominae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)