Flow of metal in a wedge-shaped cavity

The wedge shape is a fairly common cross-section found in many non-axisymmetric components used in machines, aircraft, ships and automobiles. If such components are forged between two mutually inclined dies the metal displaced by the dies flows into the converging as well as into the diverging channels created by the inclined dies. The extent of each type of flow (convergent/divergent) depends on the die—material interface friction and the included die angle. Given the initial cross-section, the length as well as the exact geometry of the forged cross-section are therefore uniquely determined by these parameters. In this paper a simple stress analysis is used to predict changes in the geometry of a wedge undergoing compression between inclined platens. The flow in directions normal to the cross-section is assumed to be negligible. Experiments carried out using wedge-shaped lead billets show that, knowing the interface friction and as long as the deformation is not too large, the dimensional changes in the wedge can be predicted with reasonable accuracy. The predicted flow behaviour of metal for a wide range of die angles and interface friction is presented: these characteristics can be used by the die designer to choose the die lubricant (only) if the die angle is specified and to choose both of these parameters if there is no restriction on the exact die angle. The present work shows that the length of a wedge undergoing compression is highly sensitive to die—material interface friction. Thus in a situation where the top and bottom dies are inclined to each other, a wedge made of the material to be forged could be put between the dies and then compressed, whereupon the length of the compressed wedge — given the degree of compression — affords an estimate of the die—material interface friction.

A non-linear analogue-to-digital converter for linearization of transducer input-output relationships

Analogue and digital techniques for linearization of non-linear input-output relationship of transducers are briefly reviewed. The condition required for linearizing a non-linear function y = f(x) using a non-linear analogue-to-digital converter, is explained. A simple technique to construct a non-linear digital-to-analogue converter, based on ' segments of equal digital interval ' is described. The technique was used to build an N-DAC which can be employed in a successive approximation or counter-ramp type ADC to linearize the non-linear transfer function of a thermistor-resistor combination. The possibility of achieving an order of magnitude higher accuracy in the measurement of temperature is shown.

Natural convection from a vertical cone in a porous medium due to the combined effects of heat and mass diffusion with non-uniform wall temperature/concentration or heat/mass flux and suction/injection

An analysis has been carried out to study the non-Darcy natural convention flow of Newtonian fluids on a vertical cone embedded in a saturated porous medium with power-law variation of the wall temperature/concentration or heat/mass flux and suction/injection with the streamwise distance x. Both non-similar and self-similar solutions have been obtained. The effects of non-Darcy parameter, ratio of the buoyancy forces due to mass and heat diffusion, variation of wall temperature/concentration or heat/mass flux and suction/injection on the Nusselt and Sherwood numbers have been studied.

Closed-form solutions for low-rank non-rigid reconstruction

Recovering the motion of a non-rigid body from a set of monocular images permits the analysis of dynamic scenes in uncontrolled environments. However, the extension of factorisation algorithms for rigid structure from motion to the low-rank non-rigid case has proved challenging. This stems from the comparatively hard problem of finding a linear “corrective transform” which recovers the projection and structure matrices from an ambiguous factorisation. We elucidate that this greater difficulty is due to the need to find multiple solutions to a non-trivial problem, casting a number of previous approaches as alleviating this issue by either a) introducing constraints on the basis, making the problems nonidentical, or b) incorporating heuristics to encourage a diverse set of solutions, making the problems inter-dependent. While it has previously been recognised that finding a single solution to this problem is sufficient to estimate cameras, we show that it is possible to bootstrap this partial solution to find the complete transform in closed-form. However, we acknowledge that our method minimises an algebraic error and is thus inherently sensitive to deviation from the low-rank model. We compare our closed-form solution for non-rigid structure with known cameras to the closed-form solution of Dai et al. [1], which we find to produce only coplanar reconstructions. We therefore make the recommendation that 3D reconstruction error always be measured relative to a trivial reconstruction such as a planar one.

Non-reductive Physicalism, Irreducibility of the Mental and the Problem of Mental Causation : A study of Donald Davidson's and Georg Henrik von Wright's positions in the philosophy of mind

In this study I consider what kind of perspective on the mind body problem is taken and can be taken by a philosophical position called non-reductive physicalism. Many positions fall under this label. The form of non-reductive physicalism which I discuss is in essential respects the position taken by Donald Davidson (1917-2003) and Georg Henrik von Wright (1916-2003). I defend their positions and discuss the unrecognized similarities between their views. Non-reductive physicalism combines two theses: (a) Everything that exists is physical; (b) Mental phenomena cannot be reduced to the states of the brain. This means that according to non-reductive physicalism the mental aspect of humans (be it a soul, mind, or spirit) is an irreducible part of the human condition. Also Davidson and von Wright claim that, in some important sense, the mental aspect of a human being does not reduce to the physical aspect, that there is a gap between these aspects that cannot be closed. I claim that their arguments for this conclusion are convincing. I also argue that whereas von Wright and Davidson give interesting arguments for the irreducibility of the mental, their physicalism is unwarranted. These philosophers do not give good reasons for believing that reality is thoroughly physical. Notwithstanding the materialistic consensus in the contemporary philosophy of mind the ontology of mind is still an uncharted territory where real breakthroughs are not to be expected until a radically new ontological position is developed. The third main claim of this work is that the problem of mental causation cannot be solved from the Davidsonian - von Wrightian perspective. The problem of mental causation is the problem of how mental phenomena like beliefs can cause physical movements of the body. As I see it, the essential point of non-reductive physicalism - the irreducibility of the mental - and the problem of mental causation are closely related. If mental phenomena do not reduce to causally effective states of the brain, then what justifies the belief that mental phenomena have causal powers? If mental causes do not reduce to physical causes, then how to tell when - or whether - the mental causes in terms of which human actions are explained are actually effective? I argue that this - how to decide when mental causes really are effective - is the real problem of mental causation. The motivation to explore and defend a non-reductive position stems from the belief that reductive physicalism leads to serious ethical problems. My claim is that Davidson's and von Wright's ultimate reason to defend a non-reductive view comes back to their belief that a reductive understanding of human nature would be a narrow and possibly harmful perspective. The final conclusion of my thesis is that von Wright's and Davidson's positions provide a starting point from which the current scientistic philosophy of mind can be critically further explored in the future.

Leveraging Lean Production Philosophy for Rationalising a Non-Linear Representation of Construction Specifications

This paper presents an approach, based on Lean production philosophy, for rationalising the processes involved in the production of specification documents for construction projects. Current construction literature erroneously depicts the process for the creation of construction specifications as a linear one. This traditional understanding of the specification process often culminates in process-wastes. On the contrary, the evidence suggests that though generalised, the activities involved in producing specification documents are nonlinear. Drawing on the outcome of participant observation, this paper presents an optimised approach for representing construction specifications. Consequently, the actors typically involved in producing specification documents are identified, the processes suitable for automation are highlighted and the central role of tacit knowledge is integrated into a conceptual template of construction specifications. By applying the transformation, flow, value (TFV) theory of Lean production the paper argues that value creation can be realised by eliminating the wastes associated with the traditional preparation of specification documents with a view to integrating specifications in digital models such as Building Information Models (BIM). Therefore, the paper presents an approach for rationalising the TFV theory as a method for optimising current approaches for generating construction specifications based on a revised specification writing model.

Effect of the Queensland Shark Control Program on non target species : whale, dugong, turtle and dolphin : a review

The Queensland Shark Control Program (QSCP) aims to protect swimmers at ten beach areas on the east coast of Queensland between Cairns (17°S) and the Gold coast (28°S). Since its inception in 1962 it has deployed shark nets and baited drumlines in a `mixed gear strategy' that adapts the type of gear to the characteristics of a site (e .g . extreme tidal range, high energy wave action, or proximity of turtle breeding areas) . The policy has provided swimmer protection, and the incidental capture of non-target species has been lower than that resulting from deployment of nets alone (Dudley 1997; Gribble et al. 1998b). The QSCP is the only major public-safety shark-control program to routinely use mixed gear. Both the New South Wales (Holt 1998) and KwaZulu-Natal (Dudley 1998) programs use nets exclusively, although the KwaZulu-Natal program has recently tested drumlines on an experimental basis (Dudley 1998; Dudley, personal communication).

Evaluation of residence time on nitrogen oxides removal in non-thermal plasma reactor

Non-thermal plasma (NTP) has been introduced over the last few years as a promising after- treatment system for nitrogen oxides and particulate matter removal from diesel exhaust. NTP technology has not been commercialised as yet, due to its high rate of energy consumption. Therefore, it is important to seek out new methods to improve NTP performance. Residence time is a crucial parameter in engine exhaust emissions treatment. In this paper, different electrode shapes are analysed and the corresponding residence time and NOx removal efficiency are studied. An axisymmetric laminar model is used for obtaining residence time distribution numerically using FLUENT software. If the mean residence time in a NTP plasma reactor increases, there will be a corresponding increase in the reaction time and consequently the pollutant removal efficiency increases. Three different screw thread electrodes and a rod electrode are examined. The results show the advantage of screw thread electrodes in comparison with the rod electrode. Furthermore, between the screw thread electrodes, the electrode with the thread width of 1 mm has the highest NOx removal due to higher residence time and a greater number of micro-discharges. The results show that the residence time of the screw thread electrode with a thread width of 1 mm is 21% more than for the rod electrode.

Inferential, non-parametric statistics to assess quality of probabilistic forecast systems

Many statistical forecast systems are available to interested users. In order to be useful for decision-making, these systems must be based on evidence of underlying mechanisms. Once causal connections between the mechanism and their statistical manifestation have been firmly established, the forecasts must also provide some quantitative evidence of `quality’. However, the quality of statistical climate forecast systems (forecast quality) is an ill-defined and frequently misunderstood property. Often, providers and users of such forecast systems are unclear about what ‘quality’ entails and how to measure it, leading to confusion and misinformation. Here we present a generic framework to quantify aspects of forecast quality using an inferential approach to calculate nominal significance levels (p-values) that can be obtained either by directly applying non-parametric statistical tests such as Kruskal-Wallis (KW) or Kolmogorov-Smirnov (KS) or by using Monte-Carlo methods (in the case of forecast skill scores). Once converted to p-values, these forecast quality measures provide a means to objectively evaluate and compare temporal and spatial patterns of forecast quality across datasets and forecast systems. Our analysis demonstrates the importance of providing p-values rather than adopting some arbitrarily chosen significance levels such as p < 0.05 or p < 0.01, which is still common practice. This is illustrated by applying non-parametric tests (such as KW and KS) and skill scoring methods (LEPS and RPSS) to the 5-phase Southern Oscillation Index classification system using historical rainfall data from Australia, The Republic of South Africa and India. The selection of quality measures is solely based on their common use and does not constitute endorsement. We found that non-parametric statistical tests can be adequate proxies for skill measures such as LEPS or RPSS. The framework can be implemented anywhere, regardless of dataset, forecast system or quality measure. Eventually such inferential evidence should be complimented by descriptive statistical methods in order to fully assist in operational risk management.

Exact evaluation of Gaussian path integrals involving non-local potentials

An exact expression for the calculation of gaussian path integrals involving non-local potentials is given. Its utility is demonstrated by using it to evaluate a path integral arising in the study of an electron gas in a random potential.

Identification and characterization of non-pathogenic Fusarium oxysporum capable of increasing and decreasing Fusarium wilt severity

Fusarium wilt of banana is a potentially devastating disease throughout the world. Options for control of the causal organism, Fusarium oxysporum f.sp. cubense (Foc) are limited. Suppressive soil sites have previously been identified where, despite the presence of Foc, Fusarium wilt does not develop. In order to understand some aspects of this disease suppression, endophytic Fusarium oxysporum isolates were obtained from banana roots. These isolates were genetically characterized and compared with an isolate of Fusarium oxysporum previously identified as being capable of suppressing Fusarium wilt of banana in glasshouse trials. Three additional isolates were selected for glasshouse trials to assess suppression of Fusarium wilt in two different cultivars of banana, Cavendish and Lady Finger. One isolate (BRIP 29089) was identified as a potential biocontrol organism, reducing the disease severity of Fusarium wilt in Lady Finger and Cavendish cultivars. Interestingly, one isolate (BRIP 45952) increased Fusarium wilt disease severity on Cavendish. The implications of an isolate of Fusarium oxysporum, non-pathogenic on banana, increasing disease severity and the potential role of non-pathogenic isolates of Fusarium oxysporum in disease complexes are discussed.

Multidisciplinary review of teaching and assessing competency attainment by non-medical prescribers

Background Prescribing is a complex task, requiring specific knowledge and skills, and the execution of effective, context-specific clinical reasoning. Systematic reviews indicate medical prescribing errors have a median rate of 7% [IQR 2%-14%] of medication orders [1-3]. For podiatrists pursuing prescribing rights, a clear need exists to ensure practitioners develop a well-defined set of prescribing skills, which will contribute to competent, safe and appropriate practice. Aim To investigate the methods employed to teach and assess the principles of effective prescribing in the undergraduate podiatry program and compare and contrast these findings with four other non-medical professions who undertake prescribing after training at Queensland University of Technology. Method The NPS National Prescribing Competency Standards were employed as the prescribing standard. A curriculum mapping exercise was undertaken to determine whether the prescribing principles articulated in the competency standards were addressed by each profession. Results A range of methods are currently utilised to teach prescribing across disciplines. Application of prescribing competencies to the context of each profession appears to influence the teaching methods used. Most competencies were taught using a multimodal format, including interactive lectures, self-directed learning, tutorial sessions and clinical placement. In particular clinical training was identified as the most consistent form of educating safe prescribers across all five disciplines. Assessment of prescribing competency utilised multiple techniques including written and oral examinations and research tasks, case studies, objective structured clinical examination exercises and the assessment of clinical practice. Effective and reliable assessment of prescribing undertaken by students in diverse settings remains challenging e.g. that occurring in the clinical practice environment. Conclusion Recommendations were made to refine curricula and to promote efficient cross-discipline teaching by staff from the disciplines of podiatry, pharmacy, nurse practitioner, optometry and paramedic science. Students now experience a sophisticated level of multidisciplinary learning in the clinical setting which integrates the expertise and skills of experience prescribers combined with innovative information technology platforms (CCTV and live patient assessments). Further work is required to establish a practical, effective approach to the assessment of prescribing competence especially between the university and clinical settings.

Identification of viral and non-viral reverse transcribing elements in pineapple ( Ananas comosus ), including members of two new badnavirus species

A previously published partial sequence of pineapple bacilliform virus was shown to be from a retrotransposon (family Metaviridae) and not from a badnavirus as previously thought. Two newly discovered sequence groups isolated from pineapple were associated with bacilliform virions and were transmitted by mealybugs. Phylogenetic analyses indicated that they were members of new badnavirus species. A third caulimovirid sequence was also amplified from pineapple, but available evidence suggests that this DNA is not encapsidated, but more likely derived from an endogenous virus.

Non-target impacts of poison baiting for predator control in Australia

1. Mammalian predators are controlled by poison baiting in many parts of the world, often to alleviate their impacts on agriculture or the environment. Although predator control can have substantial benefits, the poisons used may also be potentially harmful to other wildlife. 2. Impacts on non-target species must be minimized, but can be difficult to predict or quantify. Species and individuals vary in their sensitivity to toxins and their propensity to consume poison baits, while populations vary in their resilience. Wildlife populations can accrue benefits from predator control, which outweigh the occasional deaths of non-target animals. We review recent advances in Australia, providing a framework for assessing non-target effects of poisoning operations and for developing techniques to minimize such effects. We also emphasize that weak or circumstantial evidence of non-target effects can be misleading. 3. Weak evidence that poison baiting presents a potential risk to non-target species comes from measuring the sensitivity of species to the toxin in the laboratory. More convincing evidence may be obtained by quantifying susceptibility in the field. This requires detailed information on the propensity of animals to locate and consume poison baits, as well as the likelihood of mortality if baits are consumed. Still stronger evidence may be obtained if predator baiting causes non-target mortality in the field (with toxin detected by post-mortem examination). Conclusive proof of a negative impact on populations of non-target species can be obtained only if any observed non-target mortality is followed by sustained reductions in population density. 4. Such proof is difficult to obtain and the possibility of a population-level impact cannot be reliably confirmed or dismissed without rigorous trials. In the absence of conclusive evidence, wildlife managers should adopt a precautionary approach which seeks to minimize potential risk to non-target individuals, while clarifying population-level effects through continued research.