Some Studies and New Results on Multi Microprocessor Applications

One of the fastest expanding areas of computer exploitation is in embedded systems, whose prime function is not that of computing, but which nevertheless require information processing in order to carry out their prime function. Advances in hardware technology have made multi microprocessor systems a viable alternative to uniprocessor systems in many embedded application areas. This thesis reports the results of investigations carried out on multi microprocessors oriented towards embedded applications, with a view to enhancing throughput and reliability. An ideal controller for multiprocessor operation is developed which would smoothen sharing of routines and enable more powerful and efficient code I data interchange. Results of performance evaluation are appended.A typical application scenario is presented, which calls for classifying tasks based on characteristic features that were identified. The different classes are introduced along with a partitioned storage scheme. Theoretical analysis is also given. A review of schemes available for reducing disc access time is carried out and a new scheme presented. This is found to speed up data base transactions in embedded systems. The significance of software maintenance and adaptation in such applications is highlighted. A novel scheme of prov1d1ng a maintenance folio to system firmware is presented, alongwith experimental results. Processing reliability can be enhanced if facility exists to check if a particular instruction in a stream is appropriate. Likelihood of occurrence of a particular instruction would be more prudent if number of instructions in the set is less. A new organisation is derived to form the basement for further work. Some early results that would help steer the course of the work are presented.

Studies on short Nylon-6 fiber - elastomer composites with epoxy resin as bonding agent

The thesis describes the development and evaluation of epoxy resin as interfacial bonding agent for short Nylon-6 fiber elastomer composites. Epoxy resin is well known for its adhesive property. The potential use of it as interfacial bonding agent in short fiber composite is not explored yet. Three rubbers viz., acrylonitrile butadiene rubber (NBR), Neoprene rubber (CR) and styrene butadiene rubber (SBR) were selected and different fiber loading were tried. The resin concentration was optimized for each fiber loading with respect to cure characteristics and mechanical properties. Rheological characteristics and thermal degradation of the composites containing different fiber loading and different resin concentrations were studied in detail to find the effect of epoxy resin bonding system. The mechanical properties were studied in detail. The short Nylon -6 fiber improved most of the mechanical properties of all the three rubbers. Tensile strength showed a dip at 10 phr fiber loading in the case of CR while it was continuously increased with fiber loading in the case of NBR and SBR. All the composites showed anisotropy in mechanical properties. The epoxy resin is an effective bonding agent for short Nylon -6 fiber reinforced NBR and CR composites. Epoxy resin improved tensile strength, abrasion resistance and modulus of these composites. SEM studies confirmed the improved bonding of fiber and matrix in the presence of epoxy bonding agent. Epoxy resin was not effective as bonding agent in the case of short Nylon fiber- SBR composite. From the rheological studies of the composites with and without bonding agent it was observed that all the composite exhibited pseudoplasticity, which decreased with temperature. At higher shear rates all the mixes showed plug flow. SEM pictures showed that maximum orientation of fibers occured at a shear rate, just before the onset of plug flow. The presence of fiber reduced the temperature sensitivity of the flow at a given shear rate. Die swell was reduced in the presence of fiber. Shear viscosity of the composite was increased in the presence of resin. Die swell was increased in the presence of epoxy resin for composites at all shear rates. The thermal degradation of NBR and SBR composites with and without bonding agent followed single step degradation pattern. Thermal stability of the composites was improved in the presence of bonding agent. The degradation of virgin elastomer and the composites followed first order kinetics.

Studies on Electrical and Thermal Properties of Certain Selected Photonic Materials

The present thesis is centered around the study of electrical and thermal properties of certain selected photonic materials.We have studied the electrical conduction mechanism in various phases of certain selected photonic materials and those associated with different phase transitions occurring in them. A phase transition leaves its own impressions on the key parameters like electrical conductivity and dielectric constant. However, the activation energy calculation reveals the dominant factor responsible for conduction process.PA measurements of thermal diffusivity in certain other important photonic materials are included in the remaining part of the research work presented in this thesis. PA technique is a promising tool for studying thermal diffusivities of solid samples in any form. Because of its crucial role and common occurrence in heat flow problems, the thermal diffusivity determination is often necessary and knowledge of thermal diffusivity can intum be used to calculate the thermal conductivity. Especially,knowledge of the thermal diffusivity of semiconductors is important due to its relation to the power dissipation problem in microelectronic and optoelectronic devices which limits their performances. More than that, the thermal properties, especially those of thin films are of growing interest in microelectronics and microsystems because of the heat removal problem involved in highly integrated devices. The prescribed chapter of the present theis demonstrates how direct measurement of thermal diffusivity can be carried out in thin films of interest in a simple and elegant manner using PA techniques. Although results of only representative measurements viz; thermal diffusivity values in Indium, Aluminium, Silver and CdS thin films are given here, evaluation of this quantity for any photonic and / electronic material can be carried out using this technique in a very simple and straight forward manner.

Photothermal beam deflection for non-destructive evaluation of semiconductor thin films

Non-destructive testing (NDT) is the use of non-invasive techniques to determine the integrity of a material, component, or structure. Engineers and scientists use NDT in a variety of applications, including medical imaging, materials analysis, and process control.Photothermal beam deflection technique is one of the most promising NDT technologies. Tremendous R&D effort has been made for improving the efficiency and simplicity of this technique. It is a popular technique because it can probe surfaces irrespective of the size of the sample and its surroundings. This technique has been used to characterize several semiconductor materials, because of its non-destructive and non-contact evaluation strategy. Its application further extends to analysis of wide variety of materials. Instrumentation of a NDT technique is very crucial for any material analysis. Chapter two explores the various excitation sources, source modulation techniques, detection and signal processing schemes currently practised. The features of the experimental arrangement including the steps for alignment, automation, data acquisition and data analysis are explained giving due importance to details.Theoretical studies form the backbone of photothermal techniques. The outcome of a theoretical work is the foundation of an application.The reliability of the theoretical model developed and used is proven from the studies done on crystalline.The technique is applied for analysis of transport properties such as thermal diffusivity, mobility, surface recombination velocity and minority carrier life time of the material and thermal imaging of solar cell absorber layer materials like CuInS2, CuInSe2 and SnS thin films.analysis of In2S3 thin films, which are used as buffer layer material in solar cells. The various influences of film composition, chlorine and silver incorporation in this material is brought out from the measurement of transport properties and analysis of sub band gap levels.The application of photothermal deflection technique for characterization of solar cells is a relatively new area that requires considerable attention.The application of photothermal deflection technique for characterization of solar cells is a relatively new area that requires considerable attention. Chapter six thus elucidates the theoretical aspects of application of photothermal techniques for solar cell analysis. The experimental design and method for determination of solar cell efficiency, optimum load resistance and series resistance with results from the analysis of CuInS2/In2S3 based solar cell forms the skeleton of this chapter.

Modification of Polypropylene and Polystyrene Using Nanosilica

The present work focuses on the modification of the commonly used thermoplastics, polypropylene and polystyrene using nanosilica preparcd from a cheap source of sodium silicate. Melt compounding technique has been used for nanocomposite preparation as it is simple and suited to injection moulding. Nanosilica in a polymer matrix provide significant enhancement in strength, stiffness and impact strength. Incorporation of silica particles in a polymer also improves its thennal stability. To achieve better dispersion of fillers in polymer matrices the mixing was done at different shear rates. The enhancement in material properties indicates that at higher shear rates there is greater interaction between particles and the matrix and it depends on filler concentration and type of polymer used. N anosilica is a useful filler in thennoplastic polymers and has been applied in automotive applications, electronic appliances and consumer goods.This thesis is divided into six chapters. General introduction to the topic is described in chapter 1. Salient features of polymer nanocomposites, their synthesis, properties and applications are presented. A review of relevant literature and the scope and objectives are also mentioned in this chapter.The materials used and the vanous experimental method and techniques employed in the study are described in chapter 2. Preparation of nanocomposites by melt blending using Thenno Haake Rheocord, preparation of samples, evaluation of mechanical and thennal properties using UTM, Impact testing and characterization using DMA, TGA and DSC and morphology by SEM are described.The preparation of nanosilica from a laboratory scale to a pilot plant scale is described in chapter 3. Generation of surface modified silica, evaluation of kinetic parameters of the synthesis reaction, scale up of the reactor and modeling of the reactor are also dealt with in this chapter.The modification of the commodity thennoplastic, Polypropylene using nanosilica is described in chapter 4. Preparation of PP/silica nanocomposites, evaluation of mechanical properties, thermal and crystallization characteristics, water absorption and ageing resistance studies are also presented.The modification of Polystyrene using synthesized nanosilica IS described in chapter 5. The method of preparation of PS/silica nanocomposites, evaluation of mechanical properties (static and dynamic), thermal properties melt flow characteristics using Haake Rheocord, water absorption and ageing resistance of these nanocomposites are studied.

Studies on the fracture behaviour of polymer blends with special reference to PP/HDPE and PS/HIPS blends

Investigations on the fracture behaviour of polymer blends is the topic of this thesis. The blends selected are PP/HDPE and PS/HIPS. PP/HDPE blend is chosen due to its commercial importance and PS/HIPS blend is selected to study the transition from brittle fracture to ductile fracture.PP/HDPE blends were prepared at different compositions by melt blending at 180°C and fracture failure process was investigated by conducting notch sensitivity test and tensile test at different strain rates. The effects of two types of modifiers (particulate and elastomer) on the fracture behaviour and notch sensitivity of PP/HDPE blends were studied. The modifiers used are calcium carbonate, a hard particulate filler commonly used in plastics and Ethylene Propylene Diene Monomer (EPDM). They were added in 2%, 4% and 6% by weight of the blends.The study shows that the mechanical properties of PP/HDPE blends can be optimized by selecting proper blend compositions. The selected modifiers are found to alter and improve the fracture behaviour and notch sensitivity of the blends. Particulate fillers like calcium carbonate can be used for making the mechanical behaviour more stable at the various blend compositions. The resistance to notch sensitivity of the blends is found to be marginally lower in the presence of calcium carbonate. The elastomeric modifier EPDM produces a better stability of the mechanical behaviour. A low concentration of EPDM is sufficient to effect such a change. EPDM significantly improves the resistance to notch sensitivity of the blends. The study shows that judicious selection of modifiers can improve the fracture behaviour and notch sensitivity of PP/HDPE blends and help these materials to be used for critical applications.For investigating the transition in fracture behaviour and failure modes, PS/HIPS blends were selected. The blends were prepared by melt mixing followed by injection moulding to prepare the specimens for conducting tensile, impact and flexure tests. These tests were used to simulate the various conditions which promote failure.The tensile behaviour of unnotched and notched PS/HIPS blend samples were evaluated at slow speeds. Tensile strengths and moduli were found to increase at the higher testing speed for all the blend combinations whereas maximum strain at break was found to decrease. For a particular speed of testing, the tensile strength and modulus show only a very slight decrease as HIPS content is increased up to about 40%. However, there is a drastic decrease on increasing the HIPS content thereafter.The maximum strain at break shows only a very slight change up to about 40% HIPS content and thereafter shows a remarkable increase. The notched specimens also follow a comparable trend even though the notch sensitivity is seen high for PS rich blends containing up to 40% HIPS. The notch sensitivity marginally decreases with increase in HIPS content. At the same time, it is found to increase with the increase in strain rate. It is observed that blends containing more than 40% HIPS fail in ductile mode.The impact characteristics of PSIHIPS blends studied were impact strength, the energy absorbed by the test specimen and impact toughness. Remarkable increase in impact strength is observed as HIPS content in the blend exceeds 40%. The energy absorbed by the test specimens and the impact toughness also show a comparable trend.Flexural testing which helps to characterize the load bearing capacity was conducted on PS/HIPS blend samples at the two different testing speeds of 5mmlmin and 10 mm/min. The flexural strength increases with increase in testing speed for all the blend compositions. At both the speeds, remarkable reduction in flexural strength is observed as HIPS content in the blend exceeds 40%. The flexural strain and flexural energy absorbed by the specimens are found to increase with increase in HIPS content. At both the testing speeds, brittle fracture is observed for PS rich blends whereas HIPS rich blends show ductile mode of failure.Photoelastic investigations were conducted on PS/HIPS blend samples to analyze their failure modes. A plane polariscope with a broad source of light was utilized for the study. The coloured isochromatic fringes formed indicate the presence of residual stress concentration in the blend samples. The coverage made by the fringes on the test specimens varies with the blend composition and it shows a reducing trend with the increase in HIPS content. This indicates that the presence of residual stress is a contributing factor leading to brittle fracture in PS rich blends and this tendency gradually falls with increase in HIPS content and leads to their ductile mode of failure.

Studies on Non-Resonant Multiphoton Processes in Atomic Hydrogen

In the present thesis we have formulated the Dalgarno-Lewis procedure for two-and three-photon processes and an elegant alternate expressions are derived. Starting from a brief review on various multiphoton processes we have discussed the difficulties coming in the perturbative treatment of multiphoton processes. A small discussion on various available methods for studying multiphoton processes are presented in chapter 2. These theoretical treatments mainly concentrate on the evaluation of the higher order matrix elements coming in the perturbation theory. In chapter 3 we have described the use of Dalgarno-Lewis procedure and its implimentation on second order matrix elements. The analytical expressions for twophoton transition amplitude, two-photon ionization cross section, dipole dynamic polarizability and Kramers-Heiseberg are obtained in a unified manner. Fourth chapter is an extension of the implicit summation technique presented in chapter 3. We have clearly mentioned the advantage of our method, especially the analytical continuation of the relevant expressions suited for various values of radiation frequency which is also used for efficient numerical analysis. A possible extension of the work is to study various multiphoton processcs from the stark shifted first excited states of hydrogen atom. We can also extend this procedure for studying multiphoton processes in alkali atoms as well as Rydberg atoms. Also, instead of going for analytical expressions, one can try a complete numerical evaluation of the higher order matrix elements using this procedure.

An Evaluation of Business Deals Using Plastic Money in Kerala

School of Management Studies, Cochin University of Science and Technology

Studies on Some Aspects of Landings,Utilization and Export of Commercially Important Cephalopods

In the present study two aspects of cephalopod fishery such as (i) landings and (ii) utilization including export of cephalopods from Indian are dealt with. Under the topic landings, craft, both traditional and mechanized and fishing techniques employed for capturing cephalopods are discussed. General trend in cephalopod landing in India and particularly south west coast, species composition, description and geographic distribution of important species of cuttle fishes, squids and octopus and the distribution and abundance of cephalopods along the continental shelf of the south west coast are also discussed. Some biological aspects like population parameters, maturation and spawning, food and feeding of the two representive species of cuttle fishes and squid viz, Sepia pharaonis and Loligo duvauceli are studied.Under utilization, general handling and processing of various frozen cephalopods products for exports and commercial operation in a typical plant are studied. The export of cephalopod products since its commencement is studied in detail and market strategy for enhancing the export are suggested.

Development and Evaluation of Blind Identification Techniques for Nonlinear Systems

Identification and Control of Non‐linear dynamical systems are challenging problems to the control engineers.The topic is equally relevant in communication,weather prediction ,bio medical systems and even in social systems,where nonlinearity is an integral part of the system behavior.Most of the real world systems are nonlinear in nature and wide applications are there for nonlinear system identification/modeling.The basic approach in analyzing the nonlinear systems is to build a model from known behavior manifest in the form of system output.The problem of modeling boils down to computing a suitably parameterized model,representing the process.The parameters of the model are adjusted to optimize a performanace function,based on error between the given process output and identified process/model output.While the linear system identification is well established with many classical approaches,most of those methods cannot be directly applied for nonlinear system identification.The problem becomes more complex if the system is completely unknown but only the output time series is available.Blind recognition problem is the direct consequence of such a situation.The thesis concentrates on such problems.Capability of Artificial Neural Networks to approximate many nonlinear input-output maps makes it predominantly suitable for building a function for the identification of nonlinear systems,where only the time series is available.The literature is rich with a variety of algorithms to train the Neural Network model.A comprehensive study of the computation of the model parameters,using the different algorithms and the comparison among them to choose the best technique is still a demanding requirement from practical system designers,which is not available in a concise form in the literature.The thesis is thus an attempt to develop and evaluate some of the well known algorithms and propose some new techniques,in the context of Blind recognition of nonlinear systems.It also attempts to establish the relative merits and demerits of the different approaches.comprehensiveness is achieved in utilizing the benefits of well known evaluation techniques from statistics. The study concludes by providing the results of implementation of the currently available and modified versions and newly introduced techniques for nonlinear blind system modeling followed by a comparison of their performance.It is expected that,such comprehensive study and the comparison process can be of great relevance in many fields including chemical,electrical,biological,financial and weather data analysis.Further the results reported would be of immense help for practical system designers and analysts in selecting the most appropriate method based on the goodness of the model for the particular context.

Phytochemical investigations on ‘black glumed’ Njavara (Oryza sativa L.), the medicinal rice, as compared to staple varieties and evaluation of their antioxidant, anti-inflammatory and anticancer effects

The study was planned to investigate the bioactive compounds in Njavara compared to staple varieties and their bioactivity to substantiate the medicinal properties. Results of the study on chemical indices, antioxidant activity and antiinflammatory activity (in vivo) of Njavara black rice bran and rice in comparison with non-medicinal varieties like Sujatha and Palakkadan Matta rice bran and rice are given. The phytochemical investigation and quantification of Njavara extracts in comparison with staple varieties are detailed in this study. The last chapter is divided in three sections (A, B and C). Section A comprises the antioxidant activity by in vitro assays like DPPH, superoxide anion radical and hydrogen peroxide scavenging activity of the compounds. Also, theoretical studies using DFT were carried out based on DPPH radical scavenging activity for understanding the radical stability and mechanism of antioxidant activity. Section B comprises the anti-inflammatory activity of the identified compounds namely tricin and two flavonolignans in both in vivo and in vitro models. Section C describes the cytotoxicity of the rare flavonolignans, tricin 4’-O-(erythro-β-guaiacylglyceryl) ether and tricin 4’-O-(threo-β-guaiacylglyceryl) ether towards multiple cancer cells belonging to colon, ovarian and breast tumours.

Bioprocess Technology for Antagonistic Pseudomonas MCCB 102, 103,Micrococcus MCCB 104, and Evaluation of Synechocystis MCCB 114, 115 as Probiotics for the Management of Vibrio in Shrimp Culture Systems

National Centre for Aquatic Animal Health, School of Environmental Studies, Cochin University of Science and Technology

Biochemical & Pharmacological evaluation of liver oils of selected deep sea sharks and chimaeras of the Indian EEZ

With a seacoast of 8,1 18 km, an exclusive economic zone (EEZ) of 2 million square km, and with an area of about 30,000 square km under aquaculture, lndia produces close to six million tonnes of fish, over 4 per cent of the world fish production. While the marine waters upto 50m depth have been fully exploited, those beyond, remain unexplored. There is an ever increasing demand for fishery resources as food. The coastal fishery resources of the country are dwindling at a rapid pace and it becomes highly imperative that we search for alternate fishery resources for food. The option we have is to hunt for marine fishery resources. Studies pertaining to proximate composition, amino acid and fatty acid composition are essential to understand the nutraceutical values of these deep sea fishery resources. The present study was aimed to carry out proximate composition of deep sea fishery resources obtained during cruises onboard the FORV Sarise Sampada, to identify fishery resources which have appreciable lipid content and thereby analyse the bioactive potentials of marine lipids, to study the amino acid profile of these fishery resources, to understand the contents of SPA, MUFA and PUFA and to calculate the n3/n6 fatty acid contents. Though the presence of nutraceuticals was identified in the marine fishery resources their use as potential food resources deserve further investigation. So the study were carried out to calculate the hepatosomatic indices of sharks & chimaeras and conduct biochemical characterisation of liver oils of Apristurus indicus, Cenlrophorus scalprams, Centroselachus crepidater, Neoharriotta raleighana, and Harriotta pinnata obtained during cruises onboard the FORV Sugar Sampada.Therapeutic use of shark liver oil is evident from its use for centuries as a remedy to heal wounds and fight flu (Neil er al. 2006). Japanese seamen called it 'samedava' or "cure all". Shark liver oil is being promoted worldwide as a dietary supplement to boost the immune system, fight infections, to treat cancer and to lessen the side effects of conventional cancer treatment. These days more emphasis is laid on the nutritive benefits of shark liver oils especially on the omega 3 polyunsaturated fatty acids ( PUFAs) (Anandan er al. 2007) and alkylglycerols (AKGs) (Pugliese er al. I998) contained in them due to the high rise of inflammatory disorders such as arthritis, asthma and neurodegenerative diseases like Alzheimer’s, Parkinson’s and Schizophrenia. So the present study also evaluate the pharmacological properties with respect to analgesic, anti-inflammatory, anti pyretic and anti-ulcer effects of four different liver oils of sharks belonging to the Indian EEZ and to identify the components of oil responsible for these activities.The analgesic and anti-inflammatory activities of liver oils from Neoharriotra raleighana (NR), Centrosymnus crepidater (CC), Apristurus indicus (AI), and Centrophorus sculpratus (CS) sharks caught from the Arabian Sea and the Indian Ocean were compared. The main objectives also include determination of the cholesterol lowering effects of liver oils of Neoharriotra raleighana (NR) and Centrophorus sculpratus (CS) on the high fat diet induced dyslipidemia and to compare the impact of four isolipidemic diets, on levels of serum diagnostic marker enzymes, on lipid profile of blood and liver and antioxidant status of heart in male Albino rats. And also to study the efficacy of Centrophorus sculpratus (CS) liver oil against Complete Freund’s Adjuvant-induced arthritis and to compare the anti-inflammatory activity of this oil with a traditionally used anti-inflammatory substance gingerol (oleoresin extracted from ginger.). The results of the present study indicated that both (Centrophorus sculpratus liver oils as well as gingerol extracts proved to be effective natural remedies against CFA-induced arthritis in Albino rats.

Studies on Riverine Fishing Gears of Central Kerala

The overall focus of the thesis involves Studies on the riverine fishing geara of central kerala.Rivers and reservoirs of India harbour a rich and varied spectrum of fishes exceeding 400 species, which include commercially important fishes.The fish and fisheries play a crucial role in kerala's economy,employment generation ,food security and well being of its people.In the present study ,results of investigations conducted during 2001-2002 on riverine fishing gears of central kerala are presented along with detailed description of fishing gears,their distribution and operation covering aspects of selectivity and operational economics.Chapter I gives an introduction to the topiC of the study highlighting the relevance of the study and reviews of the existing literature on fishing gears and practices in riverine sector and sets out objectives of the study.The chapter 11 deals with the Materials and Methods used for the conduct of the investigations. In this chapter the area and the rivers selected for the study. reasons for the selection process and methodologies used for survey of riverine fishing gaear and investigations on design, structure and operation of different gear systems are presented.The chapter III discusses gillnet and its operation. Gill netting is one of the simplest and oldest methods of fishing. They are the most widely operated fishing gear in the rivers of Central Kerala. Gill netting being a low cost fishing method is of special interest for artisanal fisheries. Twenty different types of gillnets are operated in this sector.Chapter IV deals with cast nets. The origin and evolution of cast net has been briefly described in the introductory part.The chapter V deals with fishing lines, traps and other miscellaneous gears.This findings will be useful for riverine fishermen for deployment of appropriate gear systems during different seasons to ensure profitability of fishing operations.

Studies on the macrobenthic community of Cochin backwaters with special reference to culture of Eriopisa chilkensis (Gammaridae-Amphipoda)

This thesis Entitled studies on the macrobenthic community of cochin backwaters with special reference to culture of eriopisa chilkensis (Gammaridae- amphipoda).Benthic organisms are usually studied for environmental impact assessment, pollution control and resource conservation. The benthic monitoring component has three major objectives: 1) characterize the benthic communities to assess the estuarine health, 2) determine seasonal and spatial variability in benthic communities, and 3) detect changes in the estuarine community through examination of changes in abundances of specific indicator taxa and other standard benthic indices.Cochin backwaters situated at the tip of the northern Vembanad lake is a tropical positive estuarine system. The backwaters of Kerala support as much biological productivity and diversity as tropical rain forest and are responsible for the rich fishery potential of Kerala. Backwaters also act as nursery grounds for commercially important prawns and fishes.The thesis has been subdivided into seven chapters. The first chapter gives a general introduction about the topic and also highlights the scope and purpose of the study. The second chapter covers the methodology adopted for the collection and analysis of water quality parameters, sediment and the macrobenthic fauna.Chapter 3 deals with hydrographic features, sediment characteristics and the spatial variation and abundance of macrobenthic fauna in the Cochin estuary.Chapter 4 explains the impact of organic enrichment on macrobenthic popUlation in the Cochin estuary and includes the comparison of the present data with the earlier work in this region.Chapter 5 deals with seasonal variability in abundance of macrobenthic species in the estuary. The study was conducted from 9 stations during three seasons (pre-monsoon, monsoon and post-monsoon) in 2003.Chapter 6 deals with Life history and Population Dynamics of Eriopisa chilkensis Chilton (Gammaridae-Amphipoda). The life cycle of the gammarid amphipod Eriopisa chilkensis from the Cochin estuary, south west coast of India was studied for the first time under laboratory conditions.