On the optimal capacity expansion of electric power systems

The analysis of investment in the electric power has been the subject of intensive research for many years. The efficient generation and distribution of electrical energy is a difficult task involving the operation of a complex network of facilities, often located over very large geographical regions. Electric power utilities have made use of an enormous range of mathematical models. Some models address time spans which last for a fraction of a second, such as those that deal with lightning strikes on transmission lines while at the other end of the scale there are models which address time horizons consisting of ten or twenty years; these usually involve long range planning issues. This thesis addresses the optimal long term capacity expansion of an interconnected power system. The aim of this study has been to derive a new, long term planning model which recognises the regional differences which exist for energy demand and which are present in the construction and operation of power plant and transmission line equipment. Perhaps the most innovative feature of the new model is the direct inclusion of regional energy demand curves in the nonlinear form. This results in a nonlinear capacity expansion model. After review of the relevant literature, the thesis first develops a model for the optimal operation of a power grid. This model directly incorporates regional demand curves. The model is a nonlinear programming problem containing both integer and continuous variables. A solution algorithm is developed which is based upon a resource decomposition scheme that separates the integer variables from the continuous ones. The decompostion of the operating problem leads to an interactive scheme which employs a mixed integer programming problem, known as the master, to generate trial operating configurations. The optimum operating conditions of each trial configuration is found using a smooth nonlinear programming model. The dual vector recovered from this model is subsequently used by the master to generate the next trial configuration. The solution algorithm progresses until lower and upper bounds converge. A range of numerical experiments are conducted and these experiments are included in the discussion. Using the operating model as a basis, a regional capacity expansion model is then developed. It determines the type, location and capacity of additional power plants and transmission lines, which are required to meet predicted electicity demands. A generalised resource decompostion scheme, similar to that used to solve the operating problem, is employed. The solution algorithm is used to solve a range of test problems and the results of these numerical experiments are reported. Finally, the expansion problem is applied to the Queensland electricity grid in Australia.

On the optimal capacity expansion of electric power systems

The analysis of investment in the electric power has been the subject of intensive research for many years. The efficient generation and distribution of electrical energy is a difficult task involving the operation of a complex network of facilities, often located over very large geographical regions. Electric power utilities have made use of an enormous range of mathematical models. Some models address time spans which last for a fraction of a second, such as those that deal with lightning strikes on transmission lines while at the other end of the scale there are models which address time horizons consisting of ten or twenty years; these usually involve long range planning issues. This thesis addresses the optimal long term capacity expansion of an interconnected power system. The aim of this study has been to derive a new, long term planning model which recognises the regional differences which exist for energy demand and which are present in the construction and operation of power plant and transmission line equipment. Perhaps the most innovative feature of the new model is the direct inclusion of regional energy demand curves in the nonlinear form. This results in a nonlinear capacity expansion model. After review of the relevant literature, the thesis first develops a model for the optimal operation of a power grid. This model directly incorporates regional demand curves. The model is a nonlinear programming problem containing both integer and continuous variables. A solution algorithm is developed which is based upon a resource decomposition scheme that separates the integer variables from the continuous ones. The decompostion of the operating problem leads to an interactive scheme which employs a mixed integer programming problem, known as the master, to generate trial operating configurations. The optimum operating conditions of each trial configuration is found using a smooth nonlinear programming model. The dual vector recovered from this model is subsequently used by the master to generate the next trial configuration. The solution algorithm progresses until lower and upper bounds converge. A range of numerical experiments are conducted and these experiments are included in the discussion. Using the operating model as a basis, a regional capacity expansion model is then developed. It determines the type, location and capacity of additional power plants and transmission lines, which are required to meet predicted electicity demands. A generalised resource decompostion scheme, similar to that used to solve the operating problem, is employed. The solution algorithm is used to solve a range of test problems and the results of these numerical experiments are reported. Finally, the expansion problem is applied to the Queensland electricity grid in Australia

Optimising figure of merit for phonetic spoken term detection

This paper introduces a novel technique to directly optimise the Figure of Merit (FOM) for phonetic spoken term detection. The FOM is a popular measure of sTD accuracy, making it an ideal candiate for use as an objective function. A simple linear model is introduced to transform the phone log-posterior probabilities output by a phe classifier to produce enhanced log-posterior features that are more suitable for the STD task. Direct optimisation of the FOM is then performed by training the parameters of this model using a non-linear gradient descent algorithm. Substantial FOM improvements of 11% relative are achieved on held-out evaluation data, demonstrating the generalisability of the approach.

Development and implementation of the areawide Dynamic ROad traffic NoisE (DRONE) simulator

This paper discusses the areawide Dynamic ROad traffic NoisE (DRONE) simulator, and its implementation as a tool for noise abatement policy evaluation. DRONE involves integrating a road traffic noise estimation model with a traffic simulator to estimate road traffic noise in urban networks. An integrated traffic simulation-noise estimation model provides an interface for direct input of traffic flow properties from simulation model to noise estimation model that in turn estimates the noise on a spatial and temporal scale. The output from DRONE is linked with a geographical information system for visual representation of noise levels in the form of noise contour maps.

Implications of patterns of carbon pools and fluxes across a semiarid environmental gradient

Landscape scale environmental gradients present variable spatial patterns and ecological processes caused by climate, topography and soil characteristics and, as such, offer candidate sites to study environmental change. Data are presented on the spatial pattern of dominant species, biomass, and carbon pools and the temporal pattern of fluxes across a transitional zone shifting from Great Basin Desert scrub, up through pinyon-juniper woodlands and into ponderosa pine forest and the ecotones between each vegetation type. The mean annual temperature (MAT) difference across the gradient is approximately 3 degrees C from bottom to top (MAT 8.5-5.5) and annual precipitation averages from 320 to 530 mm/yr, respectively. The stems of the dominant woody vegetation approach a random spatial pattern across the entire gradient, while the canopy cover shows a clustered pattern. The size of the clusters increases with elevation according to available soil moisture which in turn affects available nutrient resources. The total density of woody species declines with increasing soil moisture along the gl-adient, but total biomass increases. Belowground carbon and nutrient pools change from a heterogenous to a homogenous distribution on either side of the woodlands. Although temperature controls the: seasonal patterns of carbon efflux from the soils, soil moisture appears to be the primary driving variable, but response differs underneath the different dominant species, Similarly, decomposition of dominant litter occurs faster-at the cooler and more moist sites, but differs within sites due to litter quality of the different species. The spatial pattern of these communities provides information on the direction of future changes, The ecological processes that we documented are not statistically different in the ecotones as compared to the: adjoining communities, but are different at sites above the woodland than those below the woodland. We speculate that an increase in MAT will have a major impact on C pools and C sequestering and release processes in these semiarid landscapes. However, the impact will be primarily related to moisture availability rather than direct effects of an increase in temperature. (C) 1998 Elsevier Science B.V.

Characterisation of Coal Seam Gas Waters in New Zealand

Coal seam gas (CSG) exploration and development requires the abstraction of significant amounts of water. This is so because gas desorbtion in coal seams takes place only after aquifer pressure has been reduced by prolonged pumping of aquifer water. CSG waters have a specific geochemical signature which is a product of their formation process. These waters have high bicarbonate, high sodium, low calcium, low magnesium, and very low sulphate concentrations. Additionally, chloride concentrations may be high depending on the coal depositional environment. This particular signature is not only useful for exploration purposes, but it also highlights potential environmental issues that can arise as a consequence of CSG water disposal. Since 2002 L&M Coal Seam Gas Ltd and CRL Energy Ltd, have been involved in exploration and development of CSG in New Zealand. Anticipating disposal of CSG waters as a key issue in CSG development, they have been assessing CSG water quality along with exploration work. Coal seam gas water samples from an exploration well in Maramarua closely follow the geochemical signature associated with CSG waters. This has helped to identify CSG potential, while at the same time assessing the chemical characteristics and water generation processes in the aquifer. Neutral pH and high alkalinity suggest that these waters could be easily managed once the sodium and chloride concentrations are reduced to acceptable levels.

Transition of synthetic chromium oxide gel to crystalline chromium oxide : a hot stage Raman spectroscopic study

Chromium oxide gel material was synthesised and appeared to be X-ray amorphous. The changes in the structure of the synthetic chromium oxide gel were investigated using hot-stage Raman spectroscopy based upon the results of thermogravimetric analysis. The thermally decomposed product of the synthetic chromium oxide gel in nitrogen atmosphere was confirmed to be crystalline Cr2O3 as determined by the hot-stage Raman spectra. Two bands were observed at 849 and 735 cm-1 in the Raman spectrum at 25 °C, which were attributed to the symmetric stretching modes of O-CrIII-OH and O-CrIII-O. With temperature increase, the intensity of the band at 849 cm-1 decreased, while the band at 735 cm-1 increased. These changes in intensity are attributed to the loss of OH groups and formation of O-CrIII-O units in the structure. A strongly hydrogen bonded water H-O-H bending band was found at 1704 cm-1 in the Raman spectrum of the chromium oxide gel, however this band shifted to around 1590 cm-1 due to destruction of the hydrogen bonds upon thermal treatment. Six new Raman bands were observed at 578, 540, 513, 390, 342 and 303 cm-1 attributed to the thermal decomposed product Cr2O3. The use of the hot-stage Raman microscope enabled low-temperature phase changes brought about through dehydration and dehydroxylation to be studied.

Understanding the impact of strategic alignment on the operational performance of post implemented technological innovations

Purpose – The purpose of this paper is to examine the role of three strategies - organisational, business and information system – in post implementation of technological innovations. The findings reported in the paper are that improvements in operational performance can only be achieved by aligning technological innovation effectiveness with operational effectiveness. Design/methodology/approach – A combination of qualitative and quantitative methods was used to apply a two-stage methodological approach. Unstructured and semi structured interviews, based on the findings of the literature, were used to identify key factors used in the survey instrument design. Confirmatory factor analysis (CFA) was used to examine structural relationships between the set of observed variables and the set of continuous latent variables. Findings – Initial findings suggest that organisations looking for improvements in operational performance through adoption of technological innovations need to align with operational strategies of the firm. Impact of operational effectiveness and technological innovation effectiveness are related directly and significantly to improved operational performance. Perception of increase of operational effectiveness is positively and significantly correlated with improved operational performance. The findings suggest that technological innovation effectiveness is also positively correlated with improved operational performance. However, the study found that there is no direct influence of strategiesorganisational, business and information systems (IS) - on improvement of operational performance. Improved operational performance is the result of interactions between the implementation of strategies and related outcomes of both technological innovation and operational effectiveness. Practical implications – Some organisations are using technological innovations such as enterprise information systems to innovate through improvements in operational performance. However, they often focus strategically only on effectiveness of technological innovation or on operational effectiveness. Such a focus will be detrimental in the long-term of the enterprise. This research demonstrated that it is not possible to achieve maximum returns through technological innovations as dimensions of operational effectiveness need to be aligned with technological innovations to improve their operational performance. Originality/value – No single technological innovation implementation can deliver a sustained competitive advantage; rather, an advantage is obtained through the capacity of an organisation to exploit technological innovations’ functionality on a continuous basis. To achieve sustainable results, technology strategy must be aligned with organisational and operational strategies. This research proposes the key performance objectives and dimensions that organisations should focus to achieve a strategic alignment. Research limitations/implications – The principal limitation of this study is that the findings are based on investigation of small sample size. There is a need to explore the appropriateness of influence of scale prior to generalizing the results of this study.

The feasibility of vibration analysis as a technique to detect osseointegration of transfemoral implants

One of the main causes of above knee or transfemoral amputation (TFA) in the developed world is trauma to the limb. The number of people undergoing TFA due to limb trauma, particularly due to war injuries, has been increasing. Typically the trauma amputee population, including war-related amputees, are otherwise healthy, active and desire to return to employment and their usual lifestyle. Consequently there is a growing need to restore long-term mobility and limb function to this population. Traditionally transfemoral amputees are provided with an artificial or prosthetic leg that consists of a fabricated socket, knee joint mechanism and a prosthetic foot. Amputees have reported several problems related to the socket of their prosthetic limb. These include pain in the residual limb, poor socket fit, discomfort and poor mobility. Removing the socket from the prosthetic limb could eliminate or reduce these problems. A solution to this is the direct attachment of the prosthesis to the residual bone (femur) inside the residual limb. This technique has been used on a small population of transfemoral amputees since 1990. A threaded titanium implant is screwed in to the shaft of the femur and a second component connects between the implant and the prosthesis. A period of time is required to allow the implant to become fully attached to the bone, called osseointegration (OI), and be able to withstand applied load; then the prosthesis can be attached. The advantages of transfemoral osseointegration (TFOI) over conventional prosthetic sockets include better hip mobility, sitting comfort and prosthetic retention and fewer skin problems on the residual limb. However, due to the length of time required for OI to progress and to complete the rehabilitation exercises, it can take up to twelve months after implant insertion for an amputee to be able to load bear and to walk unaided. The long rehabilitation time is a significant disadvantage of TFOI and may be impeding the wider adoption of the technique. There is a need for a non-invasive method of assessing the degree of osseointegration between the bone and the implant. If such a method was capable of determining the progression of TFOI and assessing when the implant was able to withstand physiological load it could reduce the overall rehabilitation time. Vibration analysis has been suggested as a potential technique: it is a non destructive method of assessing the dynamic properties of a structure. Changes in the physical properties of a structure can be identified from changes in its dynamic properties. Consequently vibration analysis, both experimental and computational, has been used to assess bone fracture healing, prosthetic hip loosening and dental implant OI with varying degrees of success. More recently experimental vibration analysis has been used in TFOI. However further work is needed to assess the potential of the technique and fully characterise the femur-implant system. The overall aim of this study was to develop physical and computational models of the TFOI femur-implant system and use these models to investigate the feasibility of vibration analysis to detect the process of OI. Femur-implant physical models were developed and manufactured using synthetic materials to represent four key stages of OI development (identified from a physiological model), simulated using different interface conditions between the implant and femur. Experimental vibration analysis (modal analysis) was then conducted using the physical models. The femur-implant models, representing stage one to stage four of OI development, were excited and the modal parameters obtained over the range 0-5kHz. The results indicated the technique had limited capability in distinguishing between different interface conditions. The fundamental bending mode did not alter with interfacial changes. However higher modes were able to track chronological changes in interface condition by the change in natural frequency, although no one modal parameter could uniquely distinguish between each interface condition. The importance of the model boundary condition (how the model is constrained) was the key finding; variations in the boundary condition altered the modal parameters obtained. Therefore the boundary conditions need to be held constant between tests in order for the detected modal parameter changes to be attributed to interface condition changes. A three dimensional Finite Element (FE) model of the femur-implant model was then developed and used to explore the sensitivity of the modal parameters to more subtle interfacial and boundary condition changes. The FE model was created using the synthetic femur geometry and an approximation of the implant geometry. The natural frequencies of the FE model were found to match the experimental frequencies within 20% and the FE and experimental mode shapes were similar. Therefore the FE model was shown to successfully capture the dynamic response of the physical system. As was found with the experimental modal analysis, the fundamental bending mode of the FE model did not alter due to changes in interface elastic modulus. Axial and torsional modes were identified by the FE model that were not detected experimentally; the torsional mode exhibited the largest frequency change due to interfacial changes (103% between the lower and upper limits of the interface modulus range). Therefore the FE model provided additional information on the dynamic response of the system and was complementary to the experimental model. The small changes in natural frequency over a large range of interface region elastic moduli indicated the method may only be able to distinguish between early and late OI progression. The boundary conditions applied to the FE model influenced the modal parameters to a far greater extent than the interface condition variations. Therefore the FE model, as well as the experimental modal analysis, indicated that the boundary conditions need to be held constant between tests in order for the detected changes in modal parameters to be attributed to interface condition changes alone. The results of this study suggest that in a clinical setting it is unlikely that the in vivo boundary conditions of the amputated femur could be adequately controlled or replicated over time and consequently it is unlikely that any longitudinal change in frequency detected by the modal analysis technique could be attributed exclusively to changes at the femur-implant interface. Therefore further development of the modal analysis technique would require significant consideration of the clinical boundary conditions and investigation of modes other than the bending modes.

Toothless tiger, sleeping dragon : implied freedoms, internet filters and the growing culture of internet censorship in Australia

The internet by its very nature challenges an individual’s notions of propriety, moral acuity and social correctness. A tension will always exist between the censorship of obscene and sensitive information and the freedom to publish and/or access such information. Freedom of expression and communication on the internet is not a static concept: ‘Its continual regeneration is the product of particular combinations of political, legal, cultural and philosophical conditions’.

Monitoring and regulatory role of the balanced scorecard in controlling organisational identities

This thesis employs the theoretical fusion of disciplinary knowledge, interlacing an analysis from both functional and interpretive frameworks and applies these paradigms to three concepts—organisational identity, the balanced scorecard performance measurement system, and control. As an applied thesis, this study highlights how particular public sector organisations are using a range of multi-disciplinary forms of knowledge constructed for their needs to achieve practical outcomes. Practical evidence of this study is not bound by a single disciplinary field or the concerns raised by academics about the rigorous application of academic knowledge. The study’s value lies in its ability to explore how current communication and accounting knowledge is being used for practical purposes in organisational life. The main focus of this thesis is on identities in an organisational communication context. In exploring the theoretical and practical challenges, the research questions for this thesis were formulated as: 1. Is it possible to effectively control identities in organisations by the use of an integrated performance measurement system—the balanced scorecard—and if so, how? 2. What is the relationship between identities and an integrated performance measurement system—the balanced scorecard—in the identity construction process? Identities in the organisational context have been extensively discussed in graphic design, corporate communication and marketing, strategic management, organisational behaviour, and social psychology literatures. Corporate identity is the self-presentation of the personality of an organisation (Van Riel, 1995; Van Riel & Balmer, 1997), and organisational identity is the statement of central characteristics described by members (Albert & Whetten, 2003). In this study, identity management is positioned as a strategically complex task, embracing not only logo and name, but also multiple dimensions, levels and facets of organisational life. Responding to the collaborative efforts of researchers and practitioners in identity conceptualisation and methodological approaches, this dissertation argues that analysis can be achieved through the use of an integrated framework of identity products, patternings and processes (Cornelissen, Haslam, & Balmer, 2007), transforming conceptualisations of corporate identity, organisational identity and identification studies. Likewise, the performance measurement literature from the accounting field now emphasises the importance of ‘soft’ non-financial measures in gauging performance—potentially allowing the monitoring and regulation of ‘collective’ identities (Cornelissen et al., 2007). The balanced scorecard (BSC) (Kaplan & Norton, 1996a), as the selected integrated performance measurement system, quantifies organisational performance under the four perspectives of finance, customer, internal process, and learning and growth. Broadening the traditional performance measurement boundary, the BSC transforms how organisations perceived themselves (Vaivio, 2007). The rhetorical and communicative value of the BSC has also been emphasised in organisational self-understanding (Malina, Nørreklit, & Selto, 2007; Malmi, 2001; Norreklit, 2000, 2003). Thus, this study establishes a theoretical connection between the controlling effects of the BSC and organisational identity construction. Common to both literatures, the aspects of control became the focus of this dissertation, as ‘the exercise or act of achieving a goal’ (Tompkins & Cheney, 1985, p. 180). This study explores not only traditional technical and bureaucratic control (Edwards, 1981), but also concertive control (Tompkins & Cheney, 1985), shifting the locus of control to employees who make their own decisions towards desired organisational premises (Simon, 1976). The controlling effects on collective identities are explored through the lens of the rhetorical frames mobilised through the power of organisational enthymemes (Tompkins & Cheney, 1985) and identification processes (Ashforth, Harrison, & Corley, 2008). In operationalising the concept of control, two guiding questions were developed to support the research questions: 1.1 How does the use of the balanced scorecard monitor identities in public sector organisations? 1.2 How does the use of the balanced scorecard regulate identities in public sector organisations? This study adopts qualitative multiple case studies using ethnographic techniques. Data were gathered from interviews of 41 managers, organisational documents, and participant observation from 2003 to 2008, to inform an understanding of organisational practices and members’ perceptions in the five cases of two public sector organisations in Australia. Drawing on the functional and interpretive paradigms, the effective design and use of the systems, as well as the understanding of shared meanings of identities and identifications are simultaneously recognised. The analytical structure guided by the ‘bracketing’ (Lewis & Grimes, 1999) and ‘interplay’ strategies (Schultz & Hatch, 1996) preserved, connected and contrasted the unique findings from the multi-paradigms. The ‘temporal bracketing’ strategy (Langley, 1999) from the process view supports the comparative exploration of the analysis over the periods under study. The findings suggest that the effective use of the BSC can monitor and regulate identity products, patternings and processes. In monitoring identities, the flexible BSC framework allowed the case study organisations to monitor various aspects of finance, customer, improvement and organisational capability that included identity dimensions. Such inclusion legitimises identity management as organisational performance. In regulating identities, the use of the BSC created a mechanism to form collective identities by articulating various perspectives and causal linkages, and through the cascading and alignment of multiple scorecards. The BSC—directly reflecting organisationally valued premises and legitimised symbols—acted as an identity product of communication, visual symbols and behavioural guidance. The selective promotion of the BSC measures filtered organisational focus to shape unique identity multiplicity and characteristics within the cases. Further, the use of the BSC facilitated the assimilation of multiple identities by controlling the direction and strength of identifications, engaging different groups of members. More specifically, the tight authority of the BSC framework and systems are explained both by technical and bureaucratic controls, while subtle communication of organisational premises and information filtering is achieved through concertive control. This study confirms that these macro top-down controls mediated the sensebreaking and sensegiving process of organisational identification, supporting research by Ashforth, Harrison and Corley (2008). This study pays attention to members’ power of self-regulation, filling minor premises of the derived logic of their organisation through the playing out of organisational enthymemes (Tompkins & Cheney, 1985). Members are then encouraged to make their own decisions towards the organisational premises embedded in the BSC, through the micro bottom-up identification processes including: enacting organisationally valued identities; sensemaking; and the construction of identity narratives aligned with those organisationally valued premises. Within the process, the self-referential effect of communication encouraged members to believe the organisational messages embedded in the BSC in transforming collective and individual identities. Therefore, communication through the use of the BSC continued the self-producing of normative performance mechanisms, established meanings of identities, and enabled members’ self-regulation in identity construction. Further, this research establishes the relationship between identity and the use of the BSC in terms of identity multiplicity and attributes. The BSC framework constrained and enabled case study organisations and members to monitor and regulate identity multiplicity across a number of dimensions, levels and facets. The use of the BSC constantly heightened the identity attributes of distinctiveness, relativity, visibility, fluidity and manageability in identity construction over time. Overall, this research explains the reciprocal controlling relationships of multiple structures in organisations to achieve a goal. It bridges the gap among corporate and organisational identity theories by adopting Cornelissen, Haslam and Balmer’s (2007) integrated identity framework, and reduces the gap in understanding between identity and performance measurement studies. Parallel review of the process of monitoring and regulating identities from both literatures synthesised the theoretical strengths of both to conceptualise and operationalise identities. This study extends the discussion on positioning identity, culture, commitment, and image and reputation measures in integrated performance measurement systems as organisational capital. Further, this study applies understanding of the multiple forms of control (Edwards, 1979; Tompkins & Cheney, 1985), emphasising the power of organisational members in identification processes, using the notion of rhetorical organisational enthymemes. This highlights the value of the collaborative theoretical power of identity, communication and performance measurement frameworks. These case studies provide practical insights about the public sector where existing bureaucracy and desired organisational identity directions are competing within a large organisational setting. Further research on personal identity and simple control in organisations that fully cascade the BSC down to individual members would provide enriched data. The extended application of the conceptual framework to other public and private sector organisations with a longitudinal view will also contribute to further theory building.

The application of a profluorescent nitroxide probe to detect reactive oxygen species derived from combustion-generated particulate matter

Particulate pollution has been widely recognised as an important risk factor to human health. In addition to increases in respiratory and cardiovascular morbidity associated with exposure to particulate matter (PM), WHO estimates that urban PM causes 0.8 million premature deaths globally and that 1.5 million people die prematurely from exposure to indoor smoke generated from the combustion of solid fuels. Despite the availability of a huge body of research, the underlying toxicological mechanisms by which particles induce adverse health effects are not yet entirely understood. Oxidative stress caused by generation of free radicals and related reactive oxygen species (ROS) at the sites of deposition has been proposed as a mechanism for many of the adverse health outcomes associated with exposure to PM. In addition to particle-induced generation of ROS in lung tissue cells, several recent studies have shown that particles may also contain ROS. As such, they present a direct cause of oxidative stress and related adverse health effects. Cellular responses to oxidative stress have been widely investigated using various cell exposure assays. However, for a rapid screening of the oxidative potential of PM, less time-consuming and less expensive, cell-free assays are needed. The main aim of this research project was to investigate the application of a novel profluorescent nitroxide probe, synthesised at QUT, as a rapid screening assay in assessing the oxidative potential of PM. Considering that this was the first time that a profluorescent nitroxide probe was applied in investigating the oxidative stress potential of PM, the proof of concept regarding the detection of PM–derived ROS by using such probes needed to be demonstrated and a sampling methodology needed to be developed. Sampling through an impinger containing profluorescent nitroxide solution was chosen as a means of particle collection as it allowed particles to react with the profluorescent nitroxide probe during sampling, avoiding in that way any possible chemical changes resulting from delays between the sampling and the analysis of the PM. Among several profluorescent nitroxide probes available at QUT, bis(phenylethynyl)anthracene-nitroxide (BPEAnit) was found to be the most suitable probe, mainly due to relatively long excitation and emission wavelengths (λex= 430 nm; λem= 485 and 513 nm). These wavelengths are long enough to avoid overlap with the background fluorescence coming from light absorbing compounds which may be present in PM (e.g. polycyclic aromatic hydrocarbons and their derivatives). Given that combustion, in general, is one of the major sources of ambient PM, this project aimed at getting an insight into the oxidative stress potential of combustion-generated PM, namely cigarette smoke, diesel exhaust and wood smoke PM. During the course of this research project, it was demonstrated that the BPEAnit probe based assay is sufficiently sensitive and robust enough to be applied as a rapid screening test for PM-derived ROS detection. Considering that for all three aerosol sources (i.e. cigarette smoke, diesel exhaust and wood smoke) the same assay was applied, the results presented in this thesis allow direct comparison of the oxidative potential measured for all three sources of PM. In summary, it was found that there was a substantial difference between the amounts of ROS per unit of PM mass (ROS concentration) for particles emitted by different combustion sources. For example, particles from cigarette smoke were found to have up to 80 times less ROS per unit of mass than particles produced during logwood combustion. For both diesel and wood combustion it has been demonstrated that the type of fuel significantly affects the oxidative potential of the particles emitted. Similarly, the operating conditions of the combustion source were also found to affect the oxidative potential of particulate emissions. Moreover, this project has demonstrated a strong link between semivolatile (i.e. organic) species and ROS and therefore, clearly highlights the importance of semivolatile species in particle-induced toxicity.

Affordable housing solutions : affordable housing providers’ perspective

Accessibility to housing for low to moderate income groups in Australia has experienced a severe decline since 2002. On the supply side, the public sector has been reducing its commitment to the direct provision of public housing. Despite strong demand for affordable housing, limited supply has been generated by non-government housing providers. This paper identifies and discusses some current affordable housing solutions which have been developed by non-government housing providers to ameliorate the problem. This study utilises case studies generated from nineteen housing providers during in-depth interviews in South East Queensland in 2007-2008. The case studies are classified into four categories which relate to the nature of their product: affordable rental housing, mixed housing, affordable housing for people with special needs and low cost home ownership. Each category is discussed on the basis of the characteristics typical of that organisation of housing provider, their partnership arrangements and main target market. In addition, the special design and facilities required for people with special needs which include high care accommodation and aged care are highlighted. Finally, this study recommends offering a continuum of solutions to affordable housing for low income people by means of a rent-to-buy scheme.

Affordable housing solutions : affordable housing providers’ perspective

Accessibility to housing for low to moderate income groups in Australia has been experiencing a severe decline since 2002. On the supply side, the public sector has been reducing its commitment to the direct provision of public housing. Despite strong demand for affordable housing, limited supply has been generated by nongovernment housing providers. This paper identifies and discusses some current affordable housing solutions to ameliorate the problem which have been developed by non-government housing providers. This study utilises case studies generated from nineteen housing providers during indepth interviews in South East Queensland in 2007-2008. The case studies are classified into four categories which relate to the nature of their product: affordable rental housing, mixed housing, affordable housing for people with special needs and low cost home ownership. Each category is discussed on the basis of the characteristics typical of that organisation of housing provider, their partnership arrangements and main target market. In addition, the special design and facilities required for people with special needs which include high care accommodation and aged care are highlighted. Finally, this study recommends offering a continuum of solutions to affordable housing for low income people by means of a rent-to-buy scheme.