Painel particulado composto por casca de eucalipto na camada intermediária

This work was developed to evalute the physical and mechanical properties of a panel of three particle layers from the test specification of NBR 14810-3 (2006), using wood of Eucalyptus sp. and Eucalyptus saligna and Eucalyptus urograndis bark. The mechanical properties were evaluated to obtain the bending modulus of rupture (MOR) and modulus of elasticity (MOE) and Internal bond. The physical properties were obtained thickness sweeling, water absorption, moisture content and board density. Were evaluated four different compositions of panels containing 5, 10, 15 and 20% in the inner layer of bark. The results were compared with the Brazilian standard NBR 14810-2 (2006) and also with studies in the literature. The panels produced were adequate to all the optimal values suggested by the standard only in the composition with 5% skin in the inner layer. The other treatments showed satisfactory results in all tests except for moisture content

Avaliação da produtividade em áreas de campo sujo com diferentes históricos de fogo

Fire is a common event in different ecosystems and can both be caused by humans or have natural sources.. In many of these ecosystems, natural fires are an important factor that determines the vegetation. The reduction of tree cover by fire for example, resulted in the evolution of several species-rich ecosystems, dominated by C4 grasses. However, the fire caused by human actions may have greater intensity and lead to negative responses of vegetation, since man changed the fire regime in many parts of the world, such as in the Cerrado. The passage of fire can benefit herbaceous and woody seedlings that cannot compete with the dominant grass layer. It removes the dead biomass and litter (major components of the fuel load), opening up spaces within the grass matrix that allow the establishment of other species. After some time without fire, an increase in shrub cover and decrease herbaceous layer can be observed. One of the major consequences of the absence of fire in savanna and grassland ecosystems is the accumulation of flammable dead biomass (mainly composed of graminoids), which will probably be the fuel load of the next burning thus, fires will be more intense and hotter. Moreover, very frequent burns lead to a reduction in the frequency and density of grasses. Therefore, this study aimed to assess the quantity and quality of biomass in areas with different fire history (fire exclusion for 2 and 7 years) in areas of campo sujo in central Cerrado. Plots (1x1m) were established in both areas and all aboveground biomass of each plot was cut at ground level and put in paper bags in the field. In the laboratory, the material was sorted into live and dead biomass. In addition, live biomass was separated into different functional groups (graminoids, forbs, Vellozia spp, palm and shrubs). The material was oven dried for two days at 80°C and subsequently weighed. In both areas, we found a dominance of graminoid and dead biomass. The area...

Implantação iônica por imersão em plasma e deposição de filmes finos poliméricos provenientes da mistura hexametildisilazano/argônio

Thin polymeric films deposited by plasma are very atractive for many industrial and scientific applications, in areas such as electronics, mechanics, coatings, biomaterials, among others, due to its favorable properties such as good adhesion to the substrate, high crosslinking, nanomectric thickness, homogeneity, etc. In this work, thin films were deposited by plasma immersion ion implantation and deposition technique from a hexamethyldisilazane/argon mixture at different proportions. These films were subjected to several characterizations, such as, contact angle, which presented values near to 100 degrees, surface energy, with values near to 31 mJ/m2, hardness with values between 0.7 and 2.6 GPa, thickness from 100 to 200 nm, refractive index from 1.56 to 1.64, molecular structure presenting the following functional groups in the infrared spectra region: CHx from 2960 to 2900 cm-1; Si-H around 2130 cm-1; CH3 in Si-(CH3)x around 1410 cm-1; CH3 in Si-(CH3)x in 1260 cm-1; N-H around 1180 cm-1; CH2 in Si-CH2-Si bonds around 1025 cm-1; Si-O in Si-O-Si from 1020 to 1100 cm-1; Si-N in Si-H-Si bonds around 940 cm-1; CH3 in Si-(CH3)3 in 850 cm-1; Si-C bonds in Si-(CH3)2 around 800 cm-1; and Si-H in 680 cm-1 . From these characterizations, it was possible to conclude that the concentration of argon or hexamethyldisilazane in the mixture changed the resulting polymer

Otimização do braço inferior da suspensão dianteira do veículo Baja utilizando o método dos elementos finitos

Mass reduction coupled with the mechanical performance in service has been the goal of many projects related to the transport area, considering the advantages that mass reduction can bring. However, make a simple material substitution without design a new geometry to corroborate for the best component performance, often makes the replacement unviable. In this study, it was investigated the advantages of replacing the prototype BAJA SAE front suspension lower arm of Equipe Piratas do Vale de BAJA SAE - Universidade Paulista, Campus Guaratinguetá, actually produced with steel, for a new component made of carbon fiber composite. The new geometry has been developed to provide the best possible performance for this component and your easy manufacturing. The study was done using the 3D modeling tools and computer simulations via finite element method. The first stage of this work consisted on calculation of the estimated maximum contact force tire / soil in a prototype landing after jump at one meter high, drop test in the laboratory with the current vehicle, current front suspension lower arm 3D modeling, finite element simulation and analysis of critical regions. After all current component analysis, a new geometry for the part in study was designed and simulated in order to reduce the component mass and provide a technological innovation using composite materials. With this work it was possible to obtain a theoretical component mass reduction of 25,15% maintaining the mechanical strength necessary for the appropriated component performance when incited

Atividade in vitro do extrato hidroalcoólico da casca de Astronium fraxinifolium (Anacardiaceae) sobre trofozoítos de Giardia duodenalis

As investigações conduzidas para avaliar novas substâncias para o tratamento da giardíase justificam-se pelo fato dos medicamentos convencionais apresentarem inconvenientes relacionados à toxicidade, à resistência e aos custos. Diante disso, a busca por novas alternativas terapêuticas tem despertado grande interesse, principalmente, entre os extratos de plantas, produtos complexos com diferentes atividades biológicas e farmacológicas. Considerando que nas infecções por Giardia, a diarréia é um dos principais sintomas, tem sido crescente o interesse em se investigar o efeito de extratos de plantas com atividade antidiarréica. Com isso, o presente trabalho foi desenvolvido com o objetivo de avaliar in vitro o efeito do extrato hidroalcoólico da casca da planta Astronium fraxinifolium, espécie típica do Cerrado brasileiro e empregada na medicina popular no tratamento contra inflamações, diarréias e úlceras gástricas. Para este fim, avaliou-se a atividade sobre o crescimento e aderência de trofozoítos de cepa autóctone de Giardia duodenalis isolada e axenizada em Botucatu, São Paulo. Em todos os ensaios, 105 trofozoítos da cepa BTU-11 foram inoculados em tubos contendo 4,5ml de meio TYI-S-33 e 100μl do extrato nas concentrações de 125; 250; 375 e 500 μg/ml. Para avaliar a atividade sobre o crescimento, os parasitas foram incubados com o extrato durante 24, 48 e 72 horas a 37°C. Nos experimentos que verificaram o efeito sobre a aderência, somente os parasitas aderidos às paredes dos tubos foram incubados com o extrato, durante 24 e 48 horas a 37°C. Em cada ensaio, os trofozoítos recuperados foram contados em câmara de Neubauer e a atividade sobre... (Resumo completo, clicar acesso eletrônico abaixo)

Biodegradação de materiais poliméricos por fungos filamentosos

The use of polymeric materials has grown in recent years due to its high durability features, atoxicity, shaping versatility and environment resistance. However, while these features represent good advantages to several industry sectors, it results in one of the most serious environmental problems of contemporary society: the rising accumulation of these material, mainly due to the inadequate disposal of waste. Meanwhile, in order to minimize this problem, some mitigation techniques comes up (arises), among which the use of biodegradable polymers has been gaining attention. Because of their easily action of microorganisms, such material degrade more rapidly, becoming integrated to nature. Furthermore, due to the fact of biodegradation is a natural process, occurring through the action if micro-organisms in the environment itself, it is considered the “cleaner” alternative found so far to plastic components reincorporation in the nature. Among the micro-organisms capable of biodegradation process are the filamentous fungi. These micro-organisms have many advantages over the others, the major one being the capacity to produce a range of enzymes capable of degrading different materials. In this context, the present review made it possible to see the importance of this process as an agent of environmental preservation, suggest the use of blends to minimize the problems of cost and flexibility of biodegradable polymeric materials, as well as noting the lack of studies related to this subject nowadays

Preparação e caracterização de compósitos expandidos obtidos a partir de raspa de couro com borracha natural

Não disponível

Proposta de conector para ensaios de ligações CDE submetidas à tração perpendicular as fibras em madeira de pinus

The growth of urban population associated with the shortage of supply of public infrastructure such as hospitals, kindergartens, schools, among others, has reinforced the need to develop alternative methods that simplify the construction processes and allows for a reduction in these costs works. The conventional processes have increasingly been shown ineffective to solve the problem of demand for different types of urban and rural buildings. Given this fact, industrial construction processes can gain space and have proven to be highly interesting to solve the above problems, in particular, considering the cost-effective and time. Therefore, this study aimed to determine the influence of moisture on the strength of metal plate connections connectors (printed plate with teeth). For the sizing of the links between structural lumber using metal connectors with teeth prints; controlled process variables (drying of the wood and the different moisture contents), and finally found results and compare them with different literatures order to obtain a qualitative efficiency of the process. Some specimens had very low expectations, can be explained by the presence of bone marrow, and pre-existing cracks. Thus, the results were discarded for further analysis and more accurate results

Avaliação de sistemas de pultrudados com diferentes tipos de matrizes para aplicação em cabos condutores

In the last decades it has been observed a substantial developing of the electrical energy demand in the societies all over the World. In consequence the electrical energy distribution companies are increasing the quantity of electrical energy through the electrical energy conductor cables, which had grown the sag in the towers of energy transmission. Furthermore, the construction of more transmission towers brings a lot of troubles due environmental protection laws. In this way, looking forward to increase the quantity of electrical energy transmitted through electrical cables conductors, reduce the need of constructing new transmission towers and the sag in them, we suggest in this work the replace of the traditional core of the conductors cables commonly used, made of steel, by a core made by a composite material, which one is made by carbon fibers pultruded with polymeric resins as matrix. In a order to evaluate if the resins more commonly used in structural composites can be applied as matrix to make possible to use the composite material as a core, we made carbon fibers systems pultruded with epoxy, phenolic and polyester resins as matrix and a mechanic and physic-chemistry characterization was done on the systems by Tensile and Poisson tests, differential sprobe calorimetry (DSC), thermogravimetric analysis (TGA) and Fourier transformed infrared spectroscopy (FTIR), following their correspondents standards

Fibras naturais: características químicas e potenciais aplicações

This study has as objective determining the chemical properties that serve as the basis for potential scientific and technological applications of seven species of fibrous plants cultivated in Brazil, which are: Banana” (Musa spp.), “Coco” (Cocos nucifera), Curauá (Ananas erectifolius), Fique (Furcraea andina), Piteira” (Furcraea gigantea), Sisal(Agave sisalana) and “Taboa” (Typha domingensis). The tests for determining the percent dry completely, extractives soluble in cold water, in hot water, in sodium hydroxide 1% and in ethanol-toluene, and the percentages of ash, hydrophobicity, lignin, holocellulose and cellulose were performed at the Department of Environmental Sciences, Agronomy College (FCA) of UNESP – Botucatu, São Paulo State. It also presents a literature review about these fibers and their potential applications. Differences between the results obtained and those found by other authors are possibly explained by variations on the origin of plant material, the harvest season, the climate and soil where they were grown. However, the results and the methodology used, serve as a basis for further studies with natural fibers

Síntese e caracterização dielétrica de filmes finos de Bi3NbO7 obtidos pelo método dos precursores poliméricos

Bi3NbO7 thin films were prepared by the polymeric precursor method. The precursor solutions were prepared with excess of bismuth ranging from 0% to 10% and the pH was controlled to be maintained between 8 and 9. This control was done by adding to the solution niobium and ethylene glycol. The final solution was clear and free of precipitation. After obtaining the precursor solution, has begun the process of characterization of powders with thermogravimetry (TG), differential thermal analysis and X-ray analysis (XRD). The films were obtained by the polymeric precursors, the method is advantageous because it is simple, and low cost involves steps and controlled stoichiometry. The films were annealed and characterized by XRD and SEM and also characterized according to their dialectics properties. We observed that the best results were obtained when the film is thermally at 800 ° C for two hours and 860 ° C for two hour. Under these conditions we obtain Bi3NbO7 thin films with good homogeneity, uniform distribution of the grains, but with the formation of secondary phase, which does not occur in treatments with lower temperature. The dielectric characterization showed that the produced film showed good characteristics with high dielectric constant and low loss

Determinação da temperatura para inativação da urease em amostras de casca e farelo de soja

s not degraded in the rumen but destroy ureasis. Soybean meal is one of the protein ingredients commonly used in formulations of animal feeds. In the diets of monogastric bran has high protein content provided by a greater separation of soybean hulls. For the ruminant protein value of the meal is lower with the inclusion of soybean hulls to reduce the level of protein. With the increased consumption of meal high protein, due to increases in production of pigs and poultry in recent years, increasing the availability of soybean hulls on the market, this is because soybean hulls is little understood in the feeding of monogastric . In this context, the main objective of this study was to determine the times and temperatures needed to ensure the effective inactivation of ureasis present in the bran and soybean hulls. According to the assessments, to make the determination of temperatures and times required for the inactivation of ureasis present in the bran and soybean hulls are 170 º C and 25 minutes for soybean meal and 140 ° C 10 minutes for soybean hulls, respectively

Aplicação do ciclo rankine orgânico alimentado termicamente pela queima da casca do arroz e resíduos de madeira

With the growing world energy demand mainly from developing countries like Brazil, Russia, India and China, the search for efficient sources of energy becomes a challenge for the coming years. Among the most widely used alternative sources, biomass is the one that grows in a more pronounced way. This study will assess the real possibility of having it as a heat source in an Organic Rankine Cycle, which employ heat transfer fluids as working fluids instead of water. From a regional data collection in agricultural production and their potential rice production and the resulting husk was defined as more appropriate. The availability of husks together with an amount of eucalyptus wood, provided by a company in the region on a monthly basis, were analyzed, and the low participation of the wood was discarded by the thermal contribution of little significance. Based on this, it was established the calorific value of fuel for thermodynamic calculations and the cycle to be used. It was then carried out the choice of working fluid from the literature and their availability in the library of software used for the simulations, the Engineering Equation Solver - ESS. The fluid most appropriate for the burning of biomass, Octamethyltrisiloxane (OMTS), was not included in the software and so the R227ea and R134a were selected. After the initial parameters modeling definition, as condensing temperature, efficiency and live steam conditions, the simulations were performed, and only the R227ea remained within the feasible thermodynamic and technological ranges. With this fluid the turbine power output was 265.7 [kW] for a scenario of 24 hours/day burning, 800.3 [kW] to biomass burning for 8 hours/day and 2134 [kW] for burning only 3 hours/day. The thermal efficiency of the cycle remained in the range of 6%, and for plants operating with the most... (Complete Abstract click eletronic access below)

Desenvolvimento de filmes finos de Bi3NbO7 pelo método dos precursores poliméricos em diferentes eletrodos óxidos

Technology always advances and thus the device miniaturization and improved performance, besides multifunctionality, they become extremely necessary. A wave of research on the area tends to grow in number and importance in today's market, it is necessary to search for new materials, new applicability of the existing ones and new processes for increasingly cheaper costs. Dielectric materials are considered a key element in this sector being the main electrical properties its high dielectric constant and low dielectric loss. The Polymeric Precursor Method appears as a good alternative because is a low cost, simple process with controlled stoichiometry. In this method, two steps were performed. In a first step, the precursor solution was decomposed into powders and in a second step the precursor solution was converted in thin films. In this work, was used the polymeric precursor methods to get thin films where they were heat treated and characterized by XRD, SEM and AFM. We have obtained Bi3NbO7 thin films with good homogeneity and uniform distribution of grains were noted. We observed that the best condition to obtain the tetragonal phase is annealing the film at high temperatures for a longer soaking time and with excess of bismuth. Several oxides electrodes were evaluated aiming to obtain textured dielectric thin films

Estudos exploratórios sobre propriedades térmicas do compósito cimento-polpa celulósica(CPC)

The search for a more aware use of available raw materials has led to a need to create more sustainable products. The use of natural fibers to reinforce cement, for instance, has been widely studied in the past decades because of the possibility that they can improve material properties such as thermal resistance and to compression, besides conferring a decrease in their total weight. This present study aimed at to conduct preliminary studies on the thermal resistance of the composite cement - Cellulose Pulp, using waste from the pulp and paper industry. Through experiments, it was found that the composite manufactured using the ratio 30 % Portland cement and 70 % pulp, showed satisfactory results regarding its thermal resistance, so it could be considered as a potential thermal insulation material, for use in constructions