Análise comparativa da rugosidade superficial de resinas compostas de alta densidade

The success achieved by the use of composite resins in anterior teeth precipitately leads their use in posterior teeth. However, the indiscriminate application of these materials in cavities with several diverse sizes rapidly pointed out their lack of resistance to oclusal and proximal wear. OBJECTIVE: To evaluate the surface roughness of composite resin in relation to finishing and polishing technique. MATERIAL AND METHODS: Eight experimental groups (n = 15) were divided according to finishing and polishing technique: G1 – Z250TM composite resin without surface finishing and polishing; G2 – Z250TM composite resin plus surface finishing and polishing; G3 – P60TM composite resin without surface finishing and polishing; G4 – P60TM composite resin plus surface finishing and polishing; G5 – Prodigy CondensableTM composite resin without surface finishing and polishing; G6 – Prodigy CondensableTM composite resin plus surface finishing and polishing; G7 – SurefillTM composite resin without surface finishing and polishing; G8 – SurefillTM composite resin plus surface finishing and polishing. Three packable and one microhybrid (control group) composite resin was used. The surface roughness was measured using a profilometer at three points in each sample. The results were evaluated by ANOVA and Tukey test (p < 0.05). RESULTS: Prodigy CondensableTM composite resin showed the lowest surface roughness, while SurefillTM showed the highest surface roughness. Comparing the resins used, only between P60TM and SurefillTM there were no statistically significant differences (p > 0,05). CONCLUSION: Surface roughness was lower in all types of resin composites surfaces in contact with Mylar matrix strip than in areas submitted to finishing and polishing procedure.

Análise estrutural e fadiga em prótese implanto-suportada unitária através do método dos elementos finitos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização de procedimentos multivariados no consumo de água e energia elétrica em habitações sociais com sistema de aquecimento solar

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Caracterização de genótipos de soja-hortaliça por análise de componentes principais

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Multivariate analysis for animal selection in experimental research

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Competência lexical na proficiência do professor de inglês como língua estrangeira: uma análise do teste oral do epple

Pós-graduação em Estudos Linguísticos - IBILCE

Análise do método suvrel na expressão diferencial a partir da matriz de contagens gerada com dados de RNA-SEQ

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Efetividade e sensibilidade com uso de géis clareadores experimental e comercial à base de peróxido de carbamida

Pós-graduação em Odontologia Restauradora - ICT

Determinação de chumbo por análise voltamétrica de pulso diferencial por redissolução anódica em regiões de falhas geológicas com emissão de radônio e filhos de radônio no município de Presidente Prudente

Pós-graduação em Química - IBILCE

Avaliação da resistência à fratura de próteses fixas temporárias reforçadas por uma malha experimental

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito da ovariectomia e da reposição hormonal no reimplante dentário imediato: análise histomorfométrica e imunoistoquímica em ratas

Pós-graduação em Odontologia - FOA

Análise econômica do milho em sucessão a diferentes adubos verdes, manejos do solo e doses de nitrogênio

Technologies that increase crop yields are possible when providing profitability to the producer. The objective of this study was to evaluate production costs and profitability of maize in production systems in Cerrado. The study was conducted in Selviria (Mato Grosso do Sul State), Brazil, in the years 2009/10 and 2010/11. The experiment was arranged in randomized blocks with four replications in factorial and mixed with tracks. We established 36 treatments, three green manures (Pennisetum glaucum, Crotalaria juncea and intercropping Pennisetum glaucum + Crotalaria juncea), three soil management practices (no-tillage system, "heavy disking" + "levelling disking" and "chisel plow" + "levelling disking") and four doses of N (0, 60, 90 and 120 kg ha(-1)). For economic analysis were estimated operational cost, the gross revenue obtained by the product of the productivity of the treatments and the value of corn (R$ 0,417 kg or R$ 25,00 sc(-1)) and the ratio revenue / cost of treatment. Whereas higher values (revenue/cost > 1) and lower (revenue/cost ratio < 1) as a parameter in the analysis of profitability, it can be concluded that corn under no-tillage had the highest profitability in succession to Pennisetum glaucum growing profitability with increasing N rates, in succession to Crotalaria juncea and in the absence of nitrogen application on the coverage achieved higher profitability compared to other treatments and in succession to the consortium Pennisetum glaucum + Crotalaria juncea doses of N was between 50 and 55 kg ha(-1) offer greater profitability to the cultivation of corn.

Análise do acabamento superficial e força de corte no torneamento de alumina a verde

In experimental conditions, cutting forces were studied during turning of green alumina billets, including their correlation with surface aspects of the workpiece. The correlation between cutting power and the removal rate are important parameters for defining the design of ceramic products, since inadequate parameters can produce excessive surface damage to the workpiece. This study examined the forces obtained during turning of alumina workpieces with 99.8% purity in their green state, by means of a three-point dynamometer, evaluating the cutting, feed and depth forces, using a cermet tool under constant machining conditions. Variables were compared with the forces, including surface finish, tool wear and temperature during machining. In the study, it was found that the depth of cut had no significant effect on the surface quality, and the cutting speed and feed influencing the finish. However, preliminary tests for selecting the cutting conditions showed that unsuitables cutting speeds and feeds generate severe damage to the workpiece surface. The best condition was 1.00 mm depth of cut, and the forces increasedfor with each pass performed, with the feed force the variable with greatest increases in relation to the cutting and depth forces, and wear of the cutting tool directly influenced the surface finish, generated by the highly abrasive nature of the alumina particles of the green compact. It is emphasized that the alumina in its green state showed high abrasive effect on the cutting tool during the turning process and the surface finishing of the green workpiece had a direct influence on the sintered workpiece.

Análise do desempenho térmico de habitações populares da microrregião de Guaratinguetá - SP

Pós-graduação em Engenharia Mecânica - FEG

Análise dos indicadores biométricos e nutricionais da cultura da alface (Lactuca sativa L.) irrigada com água tratada magneticamente utilizando modelagem fuzzy

Pós-graduação em Agronomia (Irrigação e Drenagem) - FCA