Structure of a-Si:H/a-Si1-xCx:H multilayers deposited in a reactor with automated substrate holder

This paper deals with the structural properties of a-Si:H/a-Si1-xCx: H multilayers deposited by glow-discharge decomposition of SiH4 and SiH4 and CH4 mixtures. The main feature of the rf plasma reactor is an automated substrate holder. The plasma stabilization time and its influence on the multilayer obtained is discussed. A series of a-Si:H/a-Si1-xCx: H multilayers has been deposited and characterized by secondary ion mass spectrometry (SIMS), X-ray diffraction (XRD) and transmission electron microscopy (TEM). No asymmetry between the two types of interface has been observed. The results show that the multilayers present a very good periodicity and low roughness. The difficulty of determining the abruptness of the multilayer at the nanometer scale is discussed.

Polymeerien erotus ultrasuodatuksella

Työssä selvitettiin suodatusolosuhteiden vaikutusta neutraalien polymeerien pidättymiseen niiden vesiliuoksia suodatettaessa. Suodatuksissa käytettiin kahta regeneroidusta selluloosasta valmistettua ultrasuodatuskalvoa (Microdyn-Nadir UC 030T ja JSC STC Vladipor C 30V). Malliaineina käytettiin polyetyleeniglykolia ja dekstraania. Kirjallisuusosassa esiteltiin aluksi lyhyesti ultrasuodatus erotusmenetelmänä. Lisäksi käsiteltiin ultrasuodatuskalvojen huokoskoon karakterisointimenetelmiä ja selvitettiin polymeerien erottumiseen ultrasuodatuksen aikana vaikuttavia tekijöitä. Työn kokeellisessa osassa tutkittiin paineen ja virtausnopeuden vaikutusta malliaineiden pidättymiseen ultrasuodatuskalvoilla. Lisäksi pyrittiin löytämään suodatusolosuhteet, joissa toinen aineista läpäisisi suodatuskalvon lähes täydellisesti toisen konsentroituessa syöttöliuokseen. Työssä myös määritettiin tutkimuksissa käytetyille kalvoille katkaisukoko, joka kuvaa kalvon kykyä pidättää moolimassaltaan erikokoisia molekyylejä. Lisäksi kokeellisessa osassa selvitettiin työssä käytettyjen kalvojen tasalaatuisuutta vertailemalla keskenään samanlaisissa suodatusolosuhteissa eri kalvopaloilla tehtyjen suodatusten tuloksia. Työssä saatiin erotettua kaksi lähes samankokoista malliaineeksi valittua neutraalia polymeeriä toisistaan siten, että toinen aine pidättyi kalvolla huomattavasti toista ainetta paremmin. Parhaimpaan erotustulokseen päästiin, kun permeaattivuo kalvon läpi oli noin 400 l/(m2 h). Tällöin suodatuspaine oli noin 2 bar ja virtausnopeus alle 2 m/s. Työn aikana määritettyjen katkaisukokojen havaittiin poikkeavan huomattavasti kalvojen valmistajien ilmoittamista arvoista, mutta olevan kuitenkin samaa suuruusluokkaa kuin muiden tutkimusryhmien vastaaville ultrasuodatuskalvoille esittämät arvot. Työn tulosten perusteella C 30V olisi hieman tasalaatuisempi kalvo kuin UC 030T.

Stabbing simulations and DNA transfer

Technical developments have made it possible to analyze very low amounts of DNA. This has many advantages, but the drawback of this technological progress is that interpretation of the results becomes increasingly complex: the number of mixed DNA profiles increased relatively to single source DNA profiles and stochastic effects in the DNA profile, such as drop-in and drop-out, are more frequently observed. Moreover, the relevance of low template DNA material regarding the activities alleged is not as straightforward as it was a few years ago, when for example large quantities of blood were recovered. The possibility of secondary and tertiary transfer is now becoming an issue. The purpose of this research is twofold: first, to study the transfer of DNA from the handler and secondly, to observe if handlers would transfer DNA from persons closely connected to them. We chose to mimic cases where the offender would attack a person with a knife. As a first approach, we envisaged that the defense would not give an alternative explanation for the origin of the DNA. In our transfer experiments (4 donors, 16 experiments each, 64 traces), 3% of the traces were single DNA profiles. Most of the time, the DNA profile of the person handling the knife was present as the major profile: in 83% of the traces the major contributor profile corresponded to the stabber's DNA profile (in single stains and mixtures). Mixture with no clear major/minor fraction (12%) were observed. 5% of the traces were considered of insufficient quality (more than 3 contributors, presence of a few minor peaks). In that case, we considered that the stabber's DNA was absent. In our experiments, no traces allowed excluding the stabber, however it must be noted that precautions were taken to minimize background DNA as knives were cleaned before the experiments. DNA profiles of the stabber's colleagues were not observed. We hope that this study will allow for a better understanding of the transfer mechanism and of how to assess and describe results given activity level propositions. In this preliminary research, we have focused on the transfer of DNA on the hand of the person. Besides, more research is needed to assign the probability of the results given an alternative activity proposed by the defense, for instance when the source of the DNA is not contested, but that the activities are.

A practical guide for the formulation of propositions in the bayesian approach to DNA evidence interpretation in an adversarial environment

The interpretation of complex DNA profiles is facilitated by a Bayesian approach. This approach requires the development of a pair of propositions: one aligned to the prosecution case and one to the defense case. This note explores the issue of proposition setting in an adversarial environment by a series of examples. A set of guidelines generalize how to formulate propositions when there is a single person of interest and when there are multiple individuals of interest. Additional explanations cover how to handle multiple defense propositions, relatives, and the transition from subsource level to activity level propositions. The propositions depend on case information and the allegations of each of the parties. The prosecution proposition is usually known. The authors suggest that a sensible proposition is selected for the defense that is consistent with their stance, if available, and consistent with a realistic defense if their position is not known.

Helping formulate propositions in forensic DNA analysis

The Bayesian paradigm is the preferred approach to evidence interpretation. It requires the evaluation of the probability of the evidence under at least two propositions. The value of the findings (i.e., our LR) will depend on these propositions and the case information, so it is crucial to identify which propositions are useful for the case at hand. Previously, a number of principles have been advanced and largely accepted for the evaluation of evidence. In the evaluation of traces involving DNA mixtures there may be more than two propositions possible. We apply these principles to some exemplar situations. We also show that in some cases, when there are no clear propositions or no defendant, a forensic scientist may be able to generate explanations to account for observations. In that case, the scientist plays a role of investigator, rather than evaluator. We believe that it is helpful for the scientist to distinguish those two roles.

Alternativas quimiométricas para a resolução de problemas analíticos clássicos: determinação espectrofotométrica de misturas de zircônio e háfnio

The determination of zirconium-hafnium mixtures is one of the most critical problem of the analytical chemistry, on account of the close similarity of their chemical properties. The spectrophotometric determination proposed by Yagodin et al. show not many practical applications due to the significant spectral interference on the 200-220 nm region. In this work we propound the use of a multivariate calibration method called partial least squares ( PLS ) for colorimetric determination of these mixtures. By using PLS and 16 calibration mixtures we obtained a model which permits determination of zirconium and hafnium with accuracy of about 1-2% and 10-20%, respectively. Using conventional univariate calibration the inaccuracy of the determination is about 10-25% for zirconium and above 57% for hafnium.

Modelagem dos processos químicos em plasmas de misturas gasosas usadas na corrosão de silício. Parte 1: CF4 / O2

The plasma etching of semiconductor surfaces with fluorine-containing compounds has technological interest. Presently, considerable effort is being devoted to understand the chemistry involved. In this work, a numerical modeling analysis of the gas-phase decomposition of CF4/O2 mixtures, in the presence of silicon, was performed. The relative importance of individual processes was determined as well as the effect of the parameters' uncertainties. The results were compared with experimental data. The main etching agent in the system is the fluorine atom. The concentration of the main species, SiF4, CO, CO2 and COF2 depend on the composition of the mixture.

Modelagem dos processos químicos em plasmas de misturas gasosas usadas na corrosão de silício. Parte 2: SF6 / O2

In this work, a numerical modeling analysis of the gas-phase decomposition of SF6 / O2 mixtures, in the presence of silicon, was performed. The relative importance of individual processes and the effect of the parameters' uncertainties were determined. The model was compared with experimental data for the plasma etching of silicon and with the calculated results for the CF4 / O2 system. In both systems the main etching agent is the fluorine atom and the concentration of the major species depends on the composition of the mixture. The etching rate is greater for SF6 / O2.

Discrepancies over the onset of surfactant monomer aggregation interpreted by fluorescence, conductivity and surface tension methods

Molecular probe techniques have made important contributions to the determination of microstructure of surfactant assemblies such as size, stability, micropolarity and conformation. Conductivity and surface tension were used to determine the critical aggregation concentration (cac) of polymer-surfactant complexes and the critical micellar concentration (cmc) of aqueous micellar aggregates. The results are compared with those of fluorescent techniques. Several surfactant systems were examined, 1-butanol-sodium dodecylsulfate (SDS) mixtures, solutions containing poly(ethylene oxide)-SDS, poly(vinylpyrrolidone)-SDS and poly(acrylic acid)-alkyltrimethylammonium bromide complexes. We found differences between the cac and cmc values obtained by conductivity or surface tension and those obtained by techniques which use hydrophobic probe.

Identificação de componentes de óleos voláteis: Análise espectroscópica de misturas de sesquiterpenos

This paper describes a chromatographic method to fractionate volatile oils and to identify their sesquiterpenic constituents. The fractionation process includes flash chromatography over silica gel and chromatography over silica gel/AgNO3, utilising pentane, CH2Cl2 and/or acetone as eluents. GC chromatograms were obtained in order to get the relative percentage of each constituent in the volatile oils, to get the retention time value of them as well as to analyse and combine the fractions eluted from the columns. Such procedure afford mixtures of sesquiterpenes which are analysed by GC/MS, 13C and ¹H NMR.

Triterpenos esterificados com ácidos graxos e ácidos triterpênicos isolados de Byrosonima microphylla

The hexane extract of leaves of B. microphylla afforded a mixture of triterpenes esterified with fatty acids. Analyses of spectral data of the mixture and of the derivatives obtained by a transesterification reaction with NaOMe/MeOH permitted to identify the composition of the mixtures as being 24-hydroxy-urs-12-enyl 3b-eicosanate, estearate and palmitate as well as of the 24-hydroxy-olean-12-enyl 3b-eicosanate, estearate and palmitate. From the choroform and ethyl acetate extracts were isolated the oleanolic and 3b,24-dihydroxy-urs-12-en-28-oic acids, quercetin and methyl galic ester, respectively. The compounds were identified through analysis of their spectral data.

Drug loading of mesoporous silicon particles

Porous silicon (PSi) is a promising material to be utilized in drug delivery formulations. The release rate of the drug compound can be controlled by changing the pore properties and surface chemistry of PSi. The loading of a poorly soluble drug into mesoporous silicon particles enhances its dissolution in the body. The drug loading is based on adsorption. The attainable maximum loaded amount depends on the properties of the drug compound and the PSi material, and on the process conditions. The loading solvent also essentially affects the adsorption process. The loading of indomethacin into PSi particles with varying surface modification was studied. Solvent mixtures were applied in the loading, and the loaded samples were analyzed with thermal analysis methods. The best degree of loading was obtained using a mixture of dichloromethane and methanol. The drug loads varied from 7.7 w-% to 26.8 w-%. A disturbing factor in the loading experiments was the tendency of indomethacin to form solvates with the solvents applied. In addition, the physical form and stability of indomethacin loaded in PSi and silica particles were studied using Raman spectroscopy. In the case of silica, the presence of crystalline drug as well as the polymorph form can be detected, but the method proved to be not applicable for PSi particles.

Fouling tendency in biomass-fired boilers

Although it is well known that firing biomass fuels leads to increased deposition buildup on heat transfer surfaces in boiler compared with firing coal, existing empirical knowledge about combustion of different types of biofuels is limited. The aim of this study is to give greater awareness and understanding of the circumstances which are able to decrease considerably deposition build up on heat transfer surfaces when firing different types of biofuels. The crucial part of this thesis is experimental investigation of fouling tendency while firing biomass fuels, such as straw, bark, and peat having different chemical composition. In order to give comprehensive overview of ash deposition phenomena the number of not less important issues such as mechanisms of ash deposition, effect of fouling on heat transfer, and design of boilers subjected to ash buildup were examined as well. The answers obtained in this study may be a step towards a better knowledge of firing biofuels as separately as in mixtures, and may provide solutions for successful combustion technique of biomass fuels.

Quimiometria I: calibração multivariada, um tutorial

The aim of this work is to present a tutorial on Multivariate Calibration, a tool which is nowadays necessary in basically most laboratories but very often misused. The basic concepts of preprocessing, principal component analysis (PCA), principal component regression (PCR) and partial least squares (PLS) are given. The two basic steps on any calibration procedure: model building and validation are fully discussed. The concepts of cross validation (to determine the number of factors to be used in the model), leverage and studentized residuals (to detect outliers) for the validation step are given. The whole calibration procedure is illustrated using spectra recorded for ternary mixtures of 2,4,6 trinitrophenolate, 2,4 dinitrophenolate and 2,5 dinitrophenolate followed by the concentration prediction of these three chemical species during a diffusion experiment through a hydrophobic liquid membrane. MATLAB software is used for numerical calculations. Most of the commands for the analysis are provided in order to allow a non-specialist to follow step by step the analysis.

Análise por difração de raios x de filmes de óxidos cerâmicos compostos por IrO2/TiO2/CeO2

Independent of the sample form (powder or film), XRD analysis of Ir0,3Ti(0,7-x)Ce xO2, (nominal) mixtures, for x=0, shows the formation of a solid solution phase between IrO2 and TiO2, as well as the rutile phases of IrO2 and TiO2. The presence of the anatase phase of TiO2 is also confirmed. The introduction of 30 mol% CeO2 in the mixture reveals the presence of the CeO2 and Ce2O3 phases, besides the already mentioned ones, in the powder. In the film form, however, an amorphous phase is identified. When all of the TiO2 is substituded by CeO2, for both sample forms, the only phases found are IrO2, CeO2 and Ce2O3. This result suggests cerium oxides are not capable of forming solid solutions with either IrO2 or (Ir,Ti)O2 acting solely as a dispersant matrix for these phases. These results are consistent with the much higher electrochemically active surface area when CeO2 is introduced in the binary Ti/Ir0,3Ti0,7O2 mixture. It was possible to establish a relationship between the electrochemical stability of the supported films and their crystalline structure. The unexpected presence of TiO2 and Ti2O3 in the Ti/Ir0,3Ce0,7O2 (film sample) is attributed to oxidation of the Ti support during the calcination step.