Estudo metaloproteômico do mércurio em amostras de tecido hepático de peixes coletados na área de influência do AHE JIRAU - Bacia do rio Madeira

Pós-graduação em Biologia Geral e Aplicada - IBB

Diversidade de Bacillus thuringiensis e seus genes cry e vip em amostras metagenômicas de DNA extraído do solo com cultivo de cana-de-açúcar e solo de floresta nativa em estações climáticas diferentes

Pós-graduação em Microbiologia Agropecuária - FCAV

Numerical modeling of flow through an industrial burner orifice

This paper presents numerical modeling of a turbulent natural gas flow through a non-premixed industrial burner of a slab reheating furnace. The furnace is equipped with diffusion side swirl burners capable of utilizing natural gas or coke oven gas alternatively through the same nozzles. The study is focused on one of the burners of the preheating zone. Computational Fluid Dynamics simulation has been used to predict the burner orifice turbulent flow. Flow rate and pressure at burner upstream were validated by experimental measurements. The outcomes of the numerical modeling are analyzed for the different turbulence models in terms of pressure drop, velocity profiles, and orifice discharge coefficient. The standard, RNG, and Realizable k-epsilon models and Reynolds Stress Model (RSM) have been used. The main purpose of the numerical investigation is to determine the turbulence model that more consistently reproduces the experimental results of the flow through an industrial non-premixed burner orifice. The comparisons between simulations indicate that all the models tested satisfactorily and represent the experimental conditions. However, the Realizable k-epsilon model seems to be the most appropriate turbulence model, since it provides results that are quite similar to the RSM and RNG k-epsilon models, requiring only slightly more computational power than the standard k-epsilon model. (C) 2014 Elsevier Ltd. All rights reserved.

Single Nucleotide Variations in the Buffalo Kappa-Casein Gene (CSN3)

Caseins are the major milk proteins associated with lactation performance, milk composition and cheese yield efficiency, representing around 80% of the total amount of proteins found in milk. Among the caseins, kappa-casein is the protein that stabilizes micelle structure during milk coagulation process and being used during the cheese production. The kappa-casein gene (CSN3) has been previously mapped to buffalo chromosome 7 using a radiation hybrid panel and a comparative map was established using the sequence from bovine chromosome 6. The molecular structure of this gene has also been established in river buffalo, with a total length of 13,191 bp (GenBank: AM900443.1) and containing five exons. In this study we searched for single nucleotide variations in specific regions of the CSN3 gene in three animals representing the Murrah breed. Sequencing reactions were performed using ABI3730xl sequencer. The primer walking method was used to span the 5'-UTR and intron 2 regions of the gene, for which ten primer pairs were designed using Oligo 6 software. BLAST tool was used to verify the primers specificity. DNA sequences assemblies from all three animals were performed with Sequencher (R) software 4.1, while multiple alignments were performed using Clustal W software to identify single nucleotide variations. The sequencing revealed a total of 19 single nucleotide variations with 13 located in the upstream regulatory region of the gene (5'-UTR) and six on intron 2. These variations can be validated using commercial populations segregating specific economic traits.

Can Heat Treatment Procedures of Pre-hydrolyzed Silane Replace Hydrofluoric Acid in the Adhesion of Resin Cement to Feldspathic Ceramic?

Purpose: To evaluate the influence of heat treatment (HT) procedures of a pre-hydrolyzed silane on bond strength of resin cement to a feldspathic ceramic.Materials and Methods: Ceramic and composite blocks (N = 30) were divided into six groups (n = 5) and subjected to the following conditioning procedures: G1: 9.6% hydrofluoric acid (HF) for 20 s + silane (RelyX Ceramic Primer, 3M ESPE) + resin cement (Panavia F2.0, Kuraray) (control); G2: HF (20 s) + silane + heat treatment in furnace (HTF) (100 degrees C, 2 min) + resin cement; G3: silane + HTF + resin cement; G4-HF (20 s) + silane + heat treatment with hot air (HTA) (50 +/- 5 degrees C for 1 min) + resin cement; G5: silane + HTA + resin cement; G6: silane + resin cement. The microtensile bond strength (MTBS) test was performed using a universal testing machine (1 mm/min). After debonding, the substrate and adherent surfaces were analyzed using a stereomicroscope and SEM to categorize the failure types. The data were statistically evaluated using one-way ANOVA and Tukey's test (5%).Results: The control group (G1) showed no pre-test failures and presented significantly higher mean MTBS (16.01 +/- 1.12 MPa) than did other groups (2.63 +/- 1.05 to 12.55 +/- 1.52 MPa) (p = 0.0001). In the groups where HF was not used, HTF (G3: 12.55 +/- 1.52 MPa) showed significantly higher MTBS than did HTA (G5: 2.63 +/- 1.05 MPa) (p < 0.05). All failure types were mixed, ie, adhesive between the resin cement and ceramic accompanied by cohesive failure in the cement.Conclusion: Heat treatment procedures for the pre-hydrolyzed silane either in a furnace or with the application of hot air cannot replace the use of HF gel for the adhesion of resin cement to feldspathic ceramic. Yet when mean bond strengths and incidence of pre-test failures are considered, furnace heat treatment delivered the second best results after the control group, being considerably better than hot air application.

Bismuth as a general internal standard for lead in atomic absorption spectrometry

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo comparativo in vitro da resistência ao cisalhamento de discos metálicos de níquel-cromo, com ou sem tratamento de superfície, unidos à dentina bovina com quatro cimentos

Pós-graduação em Odontologia Restauradora - ICT

Strength of 3Y-TZP and feldspathic porcelain subjected to different cooling methods

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Qualidade da pulverização em volume reduzido para o controle do bicho-mineiro Leucoptera coffeella (Guérin-Mèneville & Perrottet, 1842) (Lepidoptera: Lyonetiidae)

Pós-graduação em Agronomia (Entomologia Agrícola) - FCAV

Efeito de tratamentos térmicos nas propriedades mecânicas, eletroquímicas e citotoxidade de ligas do sistema Ti-15Mo-XNb

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Preparação e caracterização estrutural, mecânica e anelástica de ligas do sistema Ti-Ta contendo oxigênio intersticial, para uso biomédico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

M-CSF Priming of Osteoclast Precursors Can Cause Osteoclastogenesis-Insensitivity, Which Can be Prevented and Overcome on Bone

Osteoclasts and macrophages share progenitors that must receive decisive lineage signals driving them into their respective differentiation routes. Macrophage colony stimulation factor M-CSF is a common factor; bone is likely the stimulus for osteoclast differentiation. To elucidate the effect of both, shared mouse bone marrow precursor myeloid blast was pre-cultured with M-CSF on plastic and on bone. M-CSF priming prior to stimulation with M-CSF and osteoclast differentiation factor RANKL resulted in a complete loss of osteoclastogenic potential without bone. Such M-CSF primed cells expressed the receptor RANK, but lacked the crucial osteoclastogenic transcription factor NFATc1. This coincided with a steeply decreased expression of osteoclast genes TRACP and DC-STAMP, but an increased expression of the macrophage markers F4/80 and CD11b. Compellingly, M-CSF priming on bone accelerated the osteoclastogenic potential: M-CSF primed cells that had received only one day M-CSF and RANKL and were grown on bone already expressed an array of genes that are associated with osteoclast differentiation and these cells differentiated into osteoclasts within 2 days. Osteoclastogenesis-insensitive precursors grown in the absence of bone regained their osteoclastogenic potential when transferred to bone. This implies that adhesion to bone dictates the fate of osteoclast precursors. Common macrophage-osteoclast precursors may become insensitive to differentiate into osteoclasts and regain osteoclastogenesis when bound to bone or when in the vicinity of bone. J. Cell. Physiol. 229: 210-225, 2014. (c) 2014 Wiley Periodicals, Inc.

Sn(1-x)LaxO2 thin films deposited on AISI 304 stainless steel substrates

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

An improved interolog mapping-based computational prediction of protein protein interactions with increased network coverage

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sobre as considerações de uma concepção de um projeto de um forno cerâmico

The current competitiveness of the market has generated the need to minimize the cost of production companies in any field of activity, aimed at reducing the cost of production, the cost of purchasing and manufacturing processes interruption of manufacturing processes for possible maintenance. In this sense, companies are seeking methods to improve and streamline their production line. In ceramics industries, cooking the pieces is the portion of the production process that influences the total costs. The oven construction and maintenance represent a large portion embedded in the cost of the final ceramic product. The proposal for a type of oven for baking the parts that takes into account a better burning process, knowledge of the causes of disease and cost analysis of purchasing both of the constituent materials and labor for its construction, can be significant importance to the composition of final product costs or time analysis of ROI. It is proposed a streamlined design of an oven that takes into account the positive characteristics of the furnaces already built and that the experience has endorsed, and also others that are added at the end, lead to a reduction in production cost, the cost income and the number of pathologies arising from wear of the furnace along the lifespan. Therefore, according to the experiences gained over the years in the construction of furnaces and experience of manufacturing of ceramic, it is proposed a project that has an oven improvement over those now being built and that include, among other topics, economy in fuel burning, streamlining the building process