A geometric study of liquid retention in open-cell metal foams

Open-cell metal foams show promise as an emerging novel material for heat exchanger applications. The high surface-area-to-volume ratio suggests increased compactness and decrease in weight of heat exchanger designs. However, the metal foam structure appears conducive to condensate retention, which would degenerate heat transfer performance. This research investigates the condensate retention behavior of aluminum open-cell metal foams through the use of static dip tests and geometrical classification via X-ray Micro-Computed Tomography. Aluminum open-cell metal foam samples of 5, 10, 20, and 40 pores per inch (PPI), all having a void fraction greater than 90%, were included in this investigation. In order to model the condensate retention behavior of metal foams, a clearer understanding of the geometry was required. After exploring the ideal geometries presented in the open literature, X-ray Micro-Computed Tomography was employed to classify the actual geometry of the metal foam samples. The images obtained were analyzed using specialized software from which geometric information including strut length and pore shapes were extracted. The results discerned a high variability in ligament length, as well as features supporting the ideal geometry known as the Weaire-Phelan unit cell. The static dip tests consisted of submerging the metal foam samples in a liquid, then allowing gravity-induced drainage until steady-state was reached and the liquid remaining in the metal foam sample was measured. Three different liquids, water, ethylene glycol, and 91% isopropyl alcohol, were employed. The behaviors of untreated samples were compared to samples subjected to a Beomite surface treatment process, and no significant differences in retention behavior were discovered. The dip test results revealed two distinct regions of condensate retention, each holding approximately half of the total liquid retained by the sample. As expected, condensate retention increased as the pores sizes decreased. A model based on surface tension was developed to predict the condensate retention in the metal foam samples and verified using a regular mesh. Applying the model to both the ideal and actual metal foam geometries showed good agreement with the dip test results in this study.

Cell phone–based health education messaging improves health literacy.

Background: The ubiquity of cell phones, which allow for short message service (SMS), provides new and innovative opportunities for disease prevention and health education. Objective: To explore the use of cell phone–based health education SMS to improve the health literacy of community residents in China. Methods: A multi-stage random sampling method was used to select representative study communities and participants ≥ 18 years old. Intervention participants were sent health education SMSs once a week for 1 year and controls were sent conventional, basic health education measures. Health literacy levels of the residents before and after the intervention were evaluated between intervention and control groups. Results: Public health literacy scores increased 1.5 points, from 61.8 to 63.3, after SMS intervention for 1 year (P<0.01); the increase was greater for males than females (2.01 vs. 1.03; P<0.01) and for Shenzhen local residents than non-permanent residents (2.56 vs. 1.14; P<0.01). The frequency of high health literacy scores was greater for the intervention than control group (22.03% to 30.93% vs. 22.07% to 20.82%). With health literacy as a cost-effective index, the cost-effectiveness per intervention was 0.54. Conclusion: SMS may be a useful tool for improving health literacy.

Is renal medullary carcinoma the seventh nephropathy in sickle cell disease? A multi-center Nigerian survey.

Introduction: Previous studies had enlisted renal medullary carcinoma (RMC) as the seventh nephropathy in sickle cell disease (SCD). Clinical experience has contradicted this claim and this study is targeted at refuting or supporting this assumption. Objective: To estimate the prevalence of RMC and describe other renal complications in SCD. Materials and methods: 14 physicians (haematologists and urologists) in 11 tertiary institutions across the country were collated from patients’ case notes and hospital SCD registers. Results: Of the 3,596 registered sickle patients, 2 (0.056%) had been diagnosed with RMC over a ten year period, thereby giving an estimated prevalence rate of 5.6 per 100,000. The most common renal complication reported by the attending physicians was chronic kidney disease (CKD). The frequency of routine renal screening for SCD patients varied widely between centres – most were done at diagnosis, annually or bi-annually. Conclusion: The ten year prevalence of RMC in Nigerian SCD patients was determined to be 5.6 (estimated incidence of 0.56). RMC is not more common in SCD patients and therefore cannot be regarded as a “Seventh Sickle nephropathy”. Most of the managing physicians reported that the commonest nephropathy observed in their SCD patients was chronic kidney disease.

RELAZIONE TRA IL CONSUMO DI OLIO EXTRAVERGINE DI OLIVA E I CASI DI DECESSO PER MALATTIA DI ALZHEIMER IN SPAGNA

In the chemical composition of olive oil (Olea europaea L.) it is emphasized the massive presence of oleic acid (over 70%), monounsaturated fatty acid part of the family of omega 9, a 7-8% linoleic acid (omega 6) and a small presence (0.5-1%) of linolenic acid (omega 3). For its high content of monounsaturated fatty acids, olive oil is the most stable and therefore the most suitable for heating, compared to oils with a dominance of polyunsaturated fatty acids. Interest in vitamin E has increased in recent years, thanks to its high antioxidant power and its role against related diseases with age-related, visual, dermatological, cardiovascular disorders Alzheimer’s disease and more. Vegetable oils are a major source of vitamin E through diet (Sayago et al., 2007), especially with the variety of olives “Hojiblanca”. Thanks to unsaturated fatty acids cell oxidation can be prevented: this helps prevent many illness, and even premature aging. So far, the advantages acknowledged to olive oil are those of lowering cholesterol, preventing cardiovascular disease, diabetes and cancer. Among the most recent researches it is important to distinguish the studies carried out on their contribution to the prevention and treatment of breast cancer and Alzheimer’s disease. Researchers found that in addition to the benefi ts that give monounsaturated fats, in extra virgin olive oil, there is a substance called “oleocanthal”, which helps protect nerve cells damaged in Alzheimer’s disease. The importance of this discovery is enormous when one considers that only Alzheimer’s disease affects 30 million people around the world, with a different distribution depending on the type of oil in the diet (Olguín Cordero, 2012). The latest research endorses that oleocanthal works by destroying cancer cells without affecting the healthy ones, as it is stated in the Molecular and Cellular Oncology Journal. Studies carried out in different Spanish universities have concluded that thanks to the antioxidant power of olive oil, a disease such as Alzheimer can be prevented. In conclusion, we can say that the Mediterranean diet rich in extra virgin olive oil greatly infl uences on human health, reducing, delaying or even eliminating several diseases.

Open-cell Metallic Foams for the Electrochemical Conversion of Biomass-derived Compounds

The electrochemical conversion is a sustainable way for the production of added-value products, operating in mild conditions, using in-situ generated hydrogen/oxygen by water and avoiding the use of high H2/O2 pressures. The aim of this work is to investigate the electrocatalytic conversion of 5-hydroxymetilfurfural (HMF) and D-glucose, in alkaline media, using metallic open-cell foams based-catalysts. The electrochemical hydrogenation of HMF to 2,5-bis(hydroxymethyl)furan (BHMF) was performed using nanostructured Ag, deposited by galvanic displacement (GD) or electrodeposition (ED), on Cu foam, obtaining AgCu bimetallic nanoparticles (ED) or dendrites (GD) which enhanced electroactive surface area, charge and mass transfer, than bare foams. In diluted 0.02M HMF solutions, Ag/Cu samples selectively produce BHMF; the large surface area enhanced the productivity, compared to their 2D counterparts. Furthermore, at more concentrated solutions (0.05 – 0.10M) a gradually decrease of selectivity is observed. The performances of the electrodes is stable during the catalytic tests but a Cu-enrichment of particles occurred. The performances of Ni foam-based catalysts, obtained by calcination of Ni foam or by electrodeposition of Ni-hydroxide/Ni and Ni particle/Ni, were firstly investigated for the selective electrochemical oxidation of D-glucose toward gluconic acid (GO) and glucaric acid (GA). Then, the calcined catalyst was chosen to study the influence of the reaction conditions on the reaction mechanism. The GO and GA selectivities increase with the charge passed, while the formation of by-products from C-C cleavage/retro-aldol process is maximum at low charge. The fructose obtained from glucose isomerization favours the formation of by-products. The best glucose/NaOH ratio is between 0.5 and 0.1: higher values suppress the OER, while lower values favour the formation of low molecular weight products. The increases of the potential enhance the GO selectivity, nevertheless higher GA selectivity is observed at 0.6 – 0.7V vs SCE, confirmed by catalytic test performed in gluconate (30-35% GA selectivity).

Materiali ceramici a struttura Aurivillius per la produzione di solar fuels

Solar fuels from CO2 is a topic of current large scientific and industrial interest. In particular, photo-electrochemical cells (PECs) represent today one of the most promising technology for storing sun energy as chemical bonds exploiting carbon dioxide as starting reagent. In this thesis, the possibility of using Aurivillius-type compounds for the production of solar fuels was deeply investigated. Aurivillius-type perovskites, with general formula Bi(n+1)Fe(n-3)Ti3O(3n+3), were synthesized and fully characterized to study the influence of the number of perovskite layers as well as of the synthesis parameters onto their final properties. In particular, 8 different systems were considered increasing the amount of iron and, as a consequence, the number of perovskite layers. These compounds were synthesized through a standard solid-state reaction method as well as via a sol-gel technique and characterized by XRD, SEM and BET analyses. The band gap value and the photocatalytic activity towards Rhodamine B decomposition were assessed as well. For each system, a screen-printing ink was formulated to be deposited as photo-electrodes onto transparent conducting supports. The photo-electrodes were morphologically characterized by XRD and SEM analysis, and their electrochemical properties (cyclic and linear voltammetry, EIS, Mott-Schottky analysis) were determined. Finally, the most promising materials were tested as photo-cathode inside PEC cell under different illumination conditions, to quantify their ability to convert CO2. The obtained results show the potentiality of Aurivillius-type compounds as innovative material for carbon dioxide photo-electrochemical reduction.

Sintesi e caratterizzazione di CaCu3Ti4O12 (CCTO) per applicazioni in fotoelettrocatalisi

A promising strategy to mitigate both the energy crisis and global warming is the development of solar fuels and chemicals using as feedstock CO2 in combination with simple molecules such as water. This process stores the solar energy into chemical bonds, leading to a carbon-neutral approach of fuels and chemicals production. Aim of this thesis was the synthesis and characterization of CaCu3Ti4O12 (CCTO)- based compounds to be used as visible light photocatalyst for CO2 to chemical conversion. Different compositions were produced doping CCTO with increasing concentration of iron into the perovskite’s A site in order to identify the materials with the highest photo- and photoelectrocatalytic properties. The most promising compositions were used to produce photoelectrodes by screen printing that were characterized by linear and cyclic voltammetry, impedance spectroscopy and Mott-Schottky analysis to evaluate the electrical conductivity and calculate the flat band potential and the number of charge carriers in the samples. The photoelectrodes were then tested in a photoelectrochemical (PEC) cell for the conversion of CO2 into fuel and chemicals. The results obtained confirm that CCTO-based materials can be considered promising materials for carbon dioxide photo-electrochemical reduction.

Ossidazione elettrocatalitica di glucosio su schiume di nickel per la produzione selettiva di acido gluconico e acido glucarico

The selective electro-oxidation of D-glucose represents a promising way for the synthesis of many platform molecules, currently produced from non-renewable fossil fuels. Electrocatalysis is gaining considerable interest as an alternative to the thermochemical process, since it allows the process to be sustainable by operating at room temperature and pressure as well as using green solvents and electricity produced from renewable sources. In this work, the activity of three electrocatalysts, based on open cell Ni foams, towards the electrochemical oxidation of glucose to gluconic acid and glucaric acid was initially compared: a Ni bare foam, and Ni foams calcined at 500 °C for one hour and electrodeposited with Ni NP nanoparticles. The calcined foam turned out to be the most efficient. Then, the performance of this Ni calcined electrocatalyst was studied varying the reaction conditions, such as the potential applied (from 0,5V to 1,0V vs SCE), D-glucose concentration (0,01M, 0,05M and 0,10M) and NaOH concentration (0,10M and 1,0M). The activity of the electrocatalysts was evaluated in terms of glucose conversion, gluconic and gluconic acid selectivity and faradic efficiency. The best results were obtained over a Ni calcined foam with a 0,05M solution of D-glucose and 0,10M of NaOH at a 0,80V vs SCE potential.

Identificazione di nuove strategie per la valutazione della malattia minima residua nel Mieloma Multiplo: la Biopsia Liquida

Il Mieloma Multiplo (MM) è una patologia neoplastica delle cellule B caratterizzata dalla proliferazione di più cloni di plasmacellule portatrici di diverse anomalie genomiche. Il MM presenta tipicamente un’eterogeneità genomica spaziale e intraclonale, che rende l’aspirato midollare "a singolo sito", attualmente utilizzato per la valutazione della malattia residua (MRD) dopo trattamento, non realmente informativo sulla taglia di malattia e sul panorama genomico della malattia. In considerazione della crescente importanza che sta assumendo la valutazione della MRD, i test per monitorarla dovrebbero essere non invasivi, affidabili e in grado di rappresentare le eterogeneità che caratterizzano il MM. Il presente studio ha permesso di dimostrare la possibilità di utilizzare la biopsia liquida, una metodica innovativa e non invasiva, per caratterizzare i pazienti con MM attivo o con MM smoldering ad alto rischio di evoluzione (HR-SMM) e per determinale l’MRD nei pazienti sottoposti a terapia di prima linea, integrando le metodiche attualmente validate. Nei pazienti arruolati nel presente studio è stato possibile identificare la frazione tumorale di DNA libero circolante (cfDNA-TF) nel sangue periferico, ed è stato possibile caratterizzare la malattia da un punto di vista qualitativo, dimostrando un’elevata concordanza del profilo genomico tra DNA libero circolante e DNA midollare (100% nei pazienti con HR-SMM e 86% nei pazienti con MM attivo). L’esecuzione seriata di biopsie liquide in corso di terapia, con un follow-up mediano di 24 mesi, ha mostrato una rapida e netta riduzione della cfDNA-TF xdalle prime fasi di terapia, con una tendenza a mantenersi mediamente sotto la soglia di sensibilità della metodica anche nelle fasi successive, indipendentemente dall’eventuale persistenza di MRD individuabile a livello midollare o mediante PET-CT. Con un follow-up più lungo probabilmente sarà possibile valutare meglio la capacità di questa metodica di affiancare o eventualmente sostituire l’aspirato midollare.

Analysis of efficacy and safety of CAR T-cell therapy in relapsed/refractory lymphomas: current indications and future perspectives

In the last few years, the introduction of chimeric antigen receptor (CAR) T-cell therapy into clinical practice has revolutionized the approach to patients with relapsed/refractory (R/R) large B-cell lymphoma (LBCL), whose outcome used to be dismal with median overall survival (OS) of approximately 6 months with standard salvage therapy. At our Institute, we started treating diffuse large B-cell lymphoma (DLBCL) patients with CAR T-cell products in August 2019 and they received either axicabtagene ciloleucel (axi-cel) and tisagenlecleucel (tisa-cel) as per regulatory indications. This research project presents the 2-year follow-up of the first 53 treated patients. Our first aim is to investigate the feasibility of this treatment strategy in a real-world setting, although the reimbursement criteria set by the Italian Medicines Agency (Agenzia Italiana del Farmaco, AIFA) are very similar to the inclusion criteria of clinical trials and stricter than those established by the regulatory authorities of many foreign countries. One month after infusion, the ORR was 66% with 19 patients already in CR (38%). Restaging at 3, 6 and 12 months post-infusion shows that early CRs tend to be maintained over time and, moreover, that a considerable number of PRs and a few SDs can improve into a CR. The safety data were consistent with what is reported in the literature; toxicity was generally manageable, largely due to the increasing expertise in handling the specific adverse events related to CAR T-cell therapy. Our results confirms that CAR T-cell therapy is both safe and effective in a real-life setting and that it represents a crucial weapon in a subset of patients who were previously doomed to an inevitably severe prognosis.

Developing a radiomic based machine learning model to identify patients with resected non-small-cell lung cancer at high risk of relapse

Background There is a wide variation of recurrence risk of Non-small-cell lung cancer (NSCLC) within the same Tumor Node Metastasis (TNM) stage, suggesting that other parameters are involved in determining this probability. Radiomics allows extraction of quantitative information from images that can be used for clinical purposes. The primary objective of this study is to develop a radiomic prognostic model that predicts a 3 year disease free-survival (DFS) of resected Early Stage (ES) NSCLC patients. Material and Methods 56 pre-surgery non contrast Computed Tomography (CT) scans were retrieved from the PACS of our institution and anonymized. Then they were automatically segmented with an open access deep learning pipeline and reviewed by an experienced radiologist to obtain 3D masks of the NSCLC. Images and masks underwent to resampling normalization and discretization. From the masks hundreds Radiomic Features (RF) were extracted using Py-Radiomics. Hence, RF were reduced to select the most representative features. The remaining RF were used in combination with Clinical parameters to build a DFS prediction model using Leave-one-out cross-validation (LOOCV) with Random Forest. Results and Conclusion A poor agreement between the radiologist and the automatic segmentation algorithm (DICE score of 0.37) was found. Therefore, another experienced radiologist manually segmented the lesions and only stable and reproducible RF were kept. 50 RF demonstrated a high correlation with the DFS but only one was confirmed when clinicopathological covariates were added: Busyness a Neighbouring Gray Tone Difference Matrix (HR 9.610). 16 clinical variables (which comprised TNM) were used to build the LOOCV model demonstrating a higher Area Under the Curve (AUC) when RF were included in the analysis (0.67 vs 0.60) but the difference was not statistically significant (p=0,5147).

Vettore energetico idrogeno: specificità per un'adeguata sperimentazione

L'elaborato analizza, in maniera generica, come avviene la produzione, lo stoccaggio ed il trasporto dell'idrogeno e valuta i mezzi che sfruttano l'idrogeno come combustibile: i veicoli a fuel cell e i veicoli con motori a combustione interna alimentati a idrogeno (H2ICE). Poiché le proprietà dell'idrogeno sono molto diverse rispetto a quelle dei combustibili convenzionali, queste nuove tecnologie necessitano di celle di prova appositamente progettate e dimensionate. L'elaborato, pertanto, descrive nel dettaglio quali sono le normative, le strumentazioni e gli standard da rispettare per garantire che, all'interno della sala, i test possano essere eseguiti in totale sicurezza. Inoltre, vengono esaminati i sistemi di consegna e dosaggio dell'idrogeno, passando poi al sistema di ventilazione che gioca un ruolo fondamentale nel funzionamento dei test. Infine, sono riportati esempi di specifici set-up sperimentali volti allo studio delle problematiche riscontrate nei motori a combustione interna alimentati a idrogeno. Nel primo set-up, vengono descritti i sistemi di controllo, il tipo di motore e tutti i sensori utilizzati per analizzare l'impatto che ha l'EGR sui motori H2ICE; mentre, nel secondo, vengono esaminati i fattori che inducono la detonazione e la relativa frequenza.

Egfr Activating Mutations And Their Association With Response To Platinum-doublet Chemotherapy In Brazilian Non-small Cell Lung Cancer Patients.

The aim of the study was to analyze the frequency of epidermal growth factor receptor (EGFR) mutations in Brazilian non-small cell lung cancer patients and to correlate these mutations with response to benefit of platinum-based chemotherapy in non-small cell lung cancer (NSCLC). Our cohort consisted of prospective patients with NSCLCs who received chemotherapy (platinum derivates plus paclitaxel) at the [UNICAMP], Brazil. EGFR exons 18-21 were analyzed in tumor-derived DNA. Fifty patients were included in the study (25 with adenocarcinoma). EGFR mutations were identified in 6/50 (12 %) NSCLCs and in 6/25 (24 %) adenocarcinomas; representing the frequency of EGFR mutations in a mostly self-reported White (82.0 %) southeastern Brazilian population of NSCLCs. Patients with NSCLCs harboring EGFR exon 19 deletions or the exon 21 L858R mutation were found to have a higher chance of response to platinum-paclitaxel (OR 9.67 [95 % CI 1.03-90.41], p = 0.047). We report the frequency of EGFR activating mutations in a typical southeastern Brazilian population with NSCLC, which are similar to that of other countries with Western European ethnicity. EGFR mutations seem to be predictive of a response to platinum-paclitaxel, and additional studies are needed to confirm or refute this relationship.

Solid Lipid Nanoparticles For Hydrophilic Biotech Drugs: Optimization And Cell Viability Studies (caco-2 & Hepg-2 Cell Lines).

Insulin was used as model protein to developed innovative Solid Lipid Nanoparticles (SLNs) for the delivery of hydrophilic biotech drugs, with potential use in medicinal chemistry. SLNs were prepared by double emulsion with the purpose of promoting stability and enhancing the protein bioavailability. Softisan(®)100 was selected as solid lipid matrix. The surfactants (Tween(®)80, Span(®)80 and Lipoid(®)S75) and insulin were chosen applying a 2(2) factorial design with triplicate of central point, evaluating the influence of dependents variables as polydispersity index (PI), mean particle size (z-AVE), zeta potential (ZP) and encapsulation efficiency (EE) by factorial design using the ANOVA test. Therefore, thermodynamic stability, polymorphism and matrix crystallinity were checked by Differential Scanning Calorimetry (DSC) and Wide Angle X-ray Diffraction (WAXD), whereas the effect of toxicity of SLNs was check in HepG2 and Caco-2 cells. Results showed a mean particle size (z-AVE) width between 294.6 nm and 627.0 nm, a PI in the range of 0.425-0.750, ZP about -3 mV, and the EE between 38.39% and 81.20%. After tempering the bulk lipid (mimicking the end process of production), the lipid showed amorphous characteristics, with a melting point of ca. 30 °C. The toxicity of SLNs was evaluated in two distinct cell lines (HEPG-2 and Caco-2), showing to be dependent on the concentration of particles in HEPG-2 cells, while no toxicity in was reported in Caco-2 cells. SLNs were stable for 24 h in in vitro human serum albumin (HSA) solution. The resulting SLNs fabricated by double emulsion may provide a promising approach for administration of protein therapeutics and antigens.

Autologous Platelet Gel: Five Cases Illustrating Use On Sickle Cell Disease Ulcers.

Leg ulcers represent a particularly disabling complication in patients with sickle cell disease (SCD). Platelet gel (PG) is a novel therapeutic strategy used for accelerating wound healing of a wide range of tissues through the continuous release of platelet growth factors. Here, we describe the use of PG preparation according to Anitua's PRGF (preparations rich in growth factors) protocol for treating chronic nonhealing ulcers in patients with SCD. A positive response occurred in 3 patients with an area reduction of 85.7% to 100%, which occurred within 7 to 10 weeks, and a 35.2% and 20.5% of area reduction in 2 other patients, who however, had large ulcers. After calcium chloride addition, the platelet-rich plasmas demonstrated enhanced platelet-derived growth factors-BB (P < .001), transforming growth factor-β1 (P = .015), vascular endothelial growth factors (P = .03), and hepatocyte growth factors (nonsignificant) secretion. Furthermore, calcium chloride addition induced a significant decrease in platelet number (P = .0134) and there was no leukocyte detection in the PG product. These results demonstrate that PG treatment might impact the healing of leg ulcers in sickle cell disease, especially in patients with small ulcers.