Thin films composed of Ag nanoclusters dispersed in TiO2: Influence of composition and thermal annealing on the microstructure and physical responses

Noble metal powders containing gold and silver have been used for many centuries, providing different colours in the windows of the medieval cathedrals and in ancient Roman glasses. Nowadays, the interest in nanocomposite materials containing noble nanoparticles embedded in dielectric matrices is related with their potential use for a wide range of advanced technological applications. They have been proposed for environmental and biological sensing, tailoring colour of functional coatings, or for surface enhanced Raman spectroscopy. Most of these applications rely on the so-called localised surface plasmon resonance absorption, which is governed by the type of the noble metal nanoparticles, their distribution, size and shape and as well as of the dielectric characteristics of the host matrix. The aim of this work is to study the influence of the composition and thermal annealing on the morphological and structural changes of thin films composed of Ag metal clusters embedded in a dielectric TiO2 matrix. Since changes in size, shape and distribution of the clusters are fundamental parameters for tailoring the properties of plasmonic materials, a set of films with different Ag concentrations was prepared. The optical properties and the thermal behaviour of the films were correlated with the structural and morphological changes promoted by annealing. The films were deposited by DC magnetron sputtering and in order to promote the clustering of the Ag nanoparticles the as-deposited samples were subjected to an in-air annealing protocol. It was demonstrated that the clustering of metallic Ag affects the optical response spectrum and the thermal behaviour of the films.

The influence of nitrogen and oxygen additions on the thermal characteristics of aluminium-based thin films

The ternary aluminium oxynitride (AlNxOy) system offers the possibility to obtain a wide range of properties by tailoring the ratio between pure Al, AlNx and AlOy and therefore opening a significant number of possible applications. In this work the thermal behaviour of AlNxOy thin films was analysed by modulated infrared radiometry (MIRR), taking as reference the binary AlOy and AlNx systems. MIRR is a non-contact and non-destructive thermal wave measurement technique based on the excitation, propagation and detection of temperature oscillations of very small amplitudes. The intended change of the partial pressure of the reactive gas (N2 and/or O2) influenced the target condition and hence the deposition characteristics which, altogether, affected the composition and microstructure of the films. Based on the MIRR measurements and their qualitative and quantitative interpretation, some correlations between the thermal transport properties of the films and their chemical/physical properties have been found. Furthermore, the potential of such technique applied in this oxynitride system, which present a wide range of different physical responses, is also discussed. The experimental results obtained are consistent with those reported in previous works and show a high potential to fulfil the demands needed for the possible applications of the systems studied. They are clearly indicative of an adequate thermal response if this particular thin film system is aimed to be applied in small sensor devices or in electrodes for biosignal acquisition, such as those for electroencephalography or electromyography as it is the case of the main research area that is being developed in the group.

Microstructural evolution of Au/TiO2 nanocomposite films: The influence of Au concentration and thermal annealing

Nanocomposite thin films consisting of a dielectric matrix, such as titanium oxide (TiO2), with embedded gold (Au) nanoparticles were prepared and will be analysed and discussed in detail in the present work. The evolution of morphological and structural features was studied for a wide range of Au concentrations and for annealing treatments in air, for temperatures ranging from 200 to 800 °C. Major findings revealed that for low Au atomic concentrations (at.%), there are only traces of clustering, and just for relatively high annealing temperatures, T ≥ 500 °C. Furthermore, the number of Au nanoparticles is extremely low, even for the highest annealing temperature, T = 800 °C. It is noteworthy that the TiO2 matrix also crystallizes in the anatase phase for annealing temperatures above 300 °C. For intermediate Au contents (5 at.% ≤ CAu ≤ 15 at.%), the formation of gold nanoclusters was much more evident, beginning at lower annealing temperatures (T ≥ 200 °C) with sizes ranging from 2 to 25 nm as the temperature increased. A change in the matrix crystallization from anatase to rutile was also observed in this intermediate range of compositions. For the highest Au concentrations (> 20 at.%), the films tended to form relatively larger clusters, with sizes above 20 nm (for T ≥ 400 °C). It is demonstrated that the structural and morphological characteristics of the films are strongly affected by the annealing temperature, as well as by the particular amounts, size and distribution of the Au nanoparticles dispersed in the TiO2 matrix.

Evolution of the functional properties of titanium–silver thin films for biomedical applications: Influence of in-vacuum annealing

In this work, the thermal stability of TiAgx thin films, deposited by magnetron sputtering, was evaluated, envisaging their application in biomedical devices, namely as electrodes for biosignal acquisition. Based on the composition and microstructural characterization, a set of four representative TiAgx thin films was selected in order to infer whether they are thermally stable in terms of functional properties. In order to achieve this purpose, the structural and morphological evolution of the films with annealing temperature was correlated with their electrical, mechanical and thermal properties. Two distinct zones were identified and two samples from each zone were extensively analysed. In the first zone (zone I), Ti was the main component (Ti-rich zone) while in the second, zone II, the Ag content was more significant. The selected samples were annealed in vacuum at four different temperatures up to 500 oC. For the samples produced within zone I, small microstructural changes were observed due to the recrystallization of the Ti structure and grain size increment. Also, no significant changes were observed with annealing temperature regarding the f l ’ functional properties, being thermally stable up to 500 oC. For higher Ag contents (zone II) the energy supplied by thermal treatments was sufficient to activate the crystallization of Ti-Ag intermetallic phases. A strong increase of the grain size of these phases was also reported. The structural and morphological organization proved to be determinant for the physical responses of the TiAgx system. The hardness and Y g’s modulus were significantly improved with the formation of the intermetallic phases. The silver addition and annealing treatments also played an important role in the electrical conductivity of the films, which was once again improved by the formation of Ti-Ag phases. The thermal diffusivity of the films was practically unchanged with the heat-treatment. This set of results shows that this intermetallic-like thin film system has good thermal stability up to high temperatures (as high as 500 oC), which in case of the highest Ag content zone is particularly evident for electrical and mechanical properties, showing an important improvement. Hardness increases about three times, while resistivity values become half of those from the lowest Ag contents zone. These set of characteristics are consistent with the targeted applications, namely in terms of biomedical sensing devices.

Multifunctional Ti–Me (Me=Al, Cu) thin film systems for biomedical sensing devices

Ti-Me binary intermetallic thin films based on a titanium matrix doped with increasing amounts of Me (Me = Al, Cu) were prepared by magnetron sputtering (under similar conditions), aiming their application in biomedical sensing devices. The differences observed on the composition and on the micro(structural) features of the films, attributed to changes in the discharge characteristics, were correlated with the electrical properties of the intermetallic systems (Ti-Al and Ti-Cu). For the same Me exposed areas placed on the Ti target (ranging from 0.25 cm2 to 20 cm2) the Cu content increased from 3.5 at.% to 71.7 at.% in the Ti-Cu system and the Al content, in Ti-Al films, ranged from 11 to 45 at.%. The structural characterization evidenced the formation of metastable Ti-Me intermetallic phases for Al/Ti atomic ratios above 0.20 and for Cu/Ti ratios above 0.25. For lower Me concentrations, the effect of the α-Ti(Me) structure domains the overall structure. With the increase amount of the Me into Ti structure a clear trend for amorphization was observed. For both systems it was observed a significant decrease of the electrical resistivity with increasing Me/Ti atomic ratios (higher than 0.5 for Al/Ti atomic ratio and higher than 1.3 for Cu/Ti atomic ratio). Although similar trends were observed in the resistivity evolution for both systems, the Ti-Cu films presented lower resistivity values in comparison to Ti-Al system.

Desenvolvimento de um Posto de Carregamento Lento com BMS e Interface com o Cockpit para o CEPIUM

Dissertação de mestrado integrado em Engenharia Eletrónica Industrial e de Computadores

Desenvolvimento de um protótipo didático de uma máquina de corte de pedra por fio diamantado

Dissertação de mestrado integrado em Engenharia Mecânica

Conversão sistemática do comportamento definido nos blocos funcionais da norma IEC 61 131-3 para autómatos finitos temporizados

Dissertação de mestrado integrado em Engenharia Mecânica

Frameworks no desenvolvimento de software: o caso da Elevation da PRIMAVERA BSS

Dissertação de mestrado integrado em Engenharia e Gestão de Sistemas de Informação

Comparação de diferentes métodos de avaliação da capacidade de carga de pavimentos rodoviários

Dissertação de mestrado integrado em Engenharia Civil

Desenvolvimento de um laboratório pedagógico de vias de comunicação na Universidade do Minho

Dissertação de mestrado integrado em Engenharia Civil

Estudo de betumes modificados recuperados de misturas produzidas pelo método húmido e pelo método seco

Dissertação de mestrado integrado em Engenharia Civil

Prevalência de dislipidemias em adultos da demanda laboratorial de Salvador, Brasil

OBJETIVO: Determinar a prevalência das dislipidemias em adultos da demanda laboratorial não-hospitalar da cidade de Salvador (BA). MÉTODOS: Casuística procedente de amostra probabilística de 25% dos laboratórios não-hospitalares da cidade que usavam o método enzimático para dosagem dos lípides séricos e controle de qualidade da Sociedade Brasileira de Patologia Clínica (93% do total); LDL estimado pela fórmula de Friedewald. Sorteados os meses ímpares de 1995 para o estudo. Critérios para dislipidemias, em mg/dl: colesterol ³240; LDL ³160; HDL <35 e triglicérides ³200. Análise: prevalências, seus intervalos de confiança (IC) a 95% e qui-quadrado (chi²). RESULTADOS: Excluídos uma recusa e um laboratório que arquivava laudos só por 3 meses, foram analisados dados de 24 dos 26 laboratórios amostrados. Dos 7392 adultos, 65,5% eram mulheres. Prevalências estimadas e valores dos IC a 95% para homens, foram: hipercolesterolemia =24,0% (20,5; 27,5); LDL elevado =26,1 (22,4; 29,3); HDL baixo =15,9 (14,2; 17,8) e hipertrigliceridemia =27,6 (25,7; 29,5). Para mulheres: hipercolesterolemia =30,0 (27,8; 32,2), LDL elevado =33,1 (30,8; 35,4); HDL baixo =8,0 (7,1; 8,9) e hipertrigliceridemia =30,4 (29,0; 31,4). Todas as prevalências diferiram significantemente inter-gênero (p, 0,05 a p<0,001). Também foram mais freqüentes nas mulheres os níveis indesejáveis do colesterol e LDL. CONCLUSÃO: As dislipidemias são importante fator de risco para aterosclerose na demanda laboratorial de Salvador em ambos os gêneros. Os resultados subsidiam os médicos para incentivar mudanças no estilo de vida que conduzam seus pacientes a níveis lipídicos desejáveis.

Prevalência de dislipidemias na demanda laboratorial de três diferentes prestadores de assistência

OBJETIVO: Detectar diferenças nas prevalências das dislipidemias em adultos da demanda laboratorial de três diferentes prestadores de assistência médica, em Salvador, 1995. MÉTODOS: Estudo seccional, clínico epidemiológico, baseado em resultados das dosagens de lípides séricos de uma amostra probabilística de 25% dos 104 laboratórios que usavam o mesmo método de dosagem e o mesmo padrão para controle de qualidade. O critério de dislipidemia foi o do II Consenso Brasileiro de Dislipidemias para adultos. Os resultados foram agrupados conforme procedência: Sistema Único de Saúde (SUS), convênios (C) e seguros privados + particulares (SP). Análise: prevalência com intervalos de confiança (IC) a 95%, e teste do chi². RESULTADOS: Dos 5.464 adultos com menção da procedência, 14,8% foram do SUS, 31,6% dos C e 53,6% dos S+P. As mais elevadas prevalências de hipercolesterolemia - 28,0% (IC 24,0; 32,0) e de LDL-c elevado - 30,4% (IC 27,6; 33,2) foram detectadas no grupo C. No grupo S+P concentraram-se as maiores prevalências de HDL-c anormal - 12,3% (IC 10,0; 13,8) e hipertrigliceridemia - 17,8% (IC 16,3; 19,3). Quase todas as diferenças entre as prevalências foram estatisticamente significantes, favoráveis às taxas mais baixas do SUS. CONCLUSÃO: O melhor perfil lipídico do grupo SUS sugere diferenças sociais nas prevalências das dislipidemias. Para os três prestadores de assistência, a prevalência do HDL-c <35mg/dL foi baixa quando comparada às das demais dislipidemias. Os resultados podem ser inferidos para a prática médica dos respectivos prestadores de assistência e indicam a necessidade de informação e de orientação dos usuários para redução das dislipidemias e melhoria do estilo de vida.

Contributos dos ambientes digitais online para a aprendizagem em contexto de atividades de apoio extraescolar

Dissertação de mestrado em Ciências da Educação (área de especialização em Tecnologia Educativa)