963 resultados para Adubo de absorção lenta
Resumo:
Stimulation operations have with main objective restore or improve the productivity or injectivity rate in wells. Acidizing is one of the most important operations of well stimulation, consist in inject acid solutions in the formation under fracture formation pressure. Acidizing have like main purpose remove near wellbore damage, caused by drilling or workover operations, can be use in sandstones and in carbonate formations. A critical step in acidizing operation is the control of acid-formation reaction. The high kinetic rate of this reaction, promotes the consumed of the acid in region near well, causing that the acid treatment not achive the desired distance. In this way, the damage zone can not be bypassed. The main objective of this work was obtain stable systems resistant to the different conditions found in field application, evaluate the kinetic of calcite dissolution in microemulsion systems and simulate the injection of this systems by performing experiments in plugs. The systems were obtained from two non ionic surfactants, Unitol L90 and Renex 110, with sec-butanol and n-butanol like cosurfactants. The oily component of the microemlsion was xilene and kerosene. The acqueous component was a solution of HCl 15-26,1%. The results shown that the microemulsion systems obtained were stable to temperature until 100ºC, high calcium concentrations, salinity until 35000 ppm and HCl concentrations until 25%. The time for calcite dissolution in microemulsion media was 14 times slower than in aqueous HCl 15%. The simulation in plugs showed that microemulsion systems promote a distributed flux and promoted longer channels. The permeability enhancement was between 177 - 890%. The results showed that the microemulsion systems obtained have potential to be applied in matrix acidizing
Resumo:
The use of biofuels remotes to the eighteenth century, when Rudolf Diesel made the first trials using peanut oil as fuel in a compression ignition engine. Based on these trials, there was the need for some chemical change to vegetable oil. Among these chemical transformations, we can mention the cracking and transesterification. This work aims at conducting a study using the thermocatalytic and thermal cracking of sunflower oil, using the Al-MCM-41 catalyst. The material type mesoporous Al-MCM-41 was synthesized and characterized by Hydrothermical methods of X-ray diffraction, scanning electron microscopy, nitrogen adsorption, absorption spectroscopy in the infrared and thermal gravimetric analysis (TG / DTG).The study was conducted on the thermogravimetric behavior of sunflower oil on the mesoporous catalyst cited. Activation energy, conversion, and oil degradation as a function of temperature were estimated based on the integral curves of thermogravimetric analysis and the kinetic method of Vyazovkin. The mesoporous material Al-MCM-41 showed one-dimensional hexagonal formation. The study of the kinetic behavior of sunflower oil with the catalyst showed a lower activation energy against the activation energy of pure sunflower oil. Two liquid fractions of sunflower oil were obtained, both in thermal and thermocatalytic pyrolisis. The first fraction obtained was called bio-oil and the second fraction obtained was called acid fraction. The acid fraction collected, in thermal and thermocatalytic pyrolisis, showed very high level of acidity, which is why it was called acid fraction. The first fraction was collected bio-called because it presented results in the range similar to petroleum diesel
Resumo:
The program PROBIODIESEL from the Ministry of Science and Technology has substantially increased glycerine, obtained as a sub-product of biodiesel production process, making it necessary to seek alternatives for the use of this co-product. On the other hand, herbicides although play a role of fundamental importance in the agricultural production system in force, have been under growing concern among the various segments of society because of their potential environmental risk. In this work, we used glycerin in microemulsion systems for application of herbicides, to improve efficiency and lower environmental pollution caused by the loss of those products to the environment. To obtain the systems of microemulsinados were used Unitol L90 NP and Renex 40 as surfactants, butanol as co-surfactant, coconut oil as oil phase and aqueous phase as we used solutions of glycerin + water. Through the determination of phase diagrams, the microemulsion region was found in the system E (L90 Unitol, coconut oil and glycerin + water 1:1). Three points were chosen to the aqueous phase rich in characterization and application in the solubilization of glyphosate and atrazine. Three experiments were performed in Horta, Department of Plant Sciences, Plant Science Sector, UFERSA, Mossoró-RN. The first experiment was conducted in randomized complete blocks with 20 treatments and four replications. The treatments consisted of five doses of the herbicide glyphosate (0.0, 0.45, 0.9, 1.35 and 1.8 L ha-1) diluted with four sauces: C1, C2, C3 (microemulsions) and C4 (water). The phytotoxicity of Brachiaria brizantha was measured at 7, 14, 28 and 60 DAA (days after application). At 60 DAA, we evaluated the biomass of plants. The second experiment was developed in randomized complete blocks with 20 treatments and four repetitions. The treatments consisted of five doses of the herbicide atrazine (0.0, 0.4, 0.8, 1.6 and 2.4 L ha-1) diluted with four sauces: C1, C2, C3 (microemulsions) and C4 (water). The phytotoxicity on Zea mays and Talinum paniculatum was evaluated at 2, 7, 20 DAA. The experiment III was developed in randomized complete blocks with 16 treatments and three repetitions. The treatments consisted of 16 combinations among the constituents of the microemulsion: Unitol L90 surfactant (0.0, 1.66, 5.0, 15 %) and glycerin (0.0, 4.44, 13.33 and 40.0 %). The phytotoxicity on Zea mays was evaluated at 1, 7 and 14 DAA. At 14 DAA, we evaluated the biomass of plants. The control plants using the microemulsions was lower than in the water due to the poisoning caused by the initial microemulsions in the leaves of the plants, a fact that hinders the absorption and translocation of the herbicide. There was no toxicity in Zea mays plants caused by the herbicide, however, were highly intoxicated by microemulsions. T. paniculatum was better controlled in spraying with the microemulsions, regardless of the dose of the herbicide. The glycerine did not cause plant damage. Higher poisoning the plants are caused by tensoactive Unitol L90 and higher rates occur with the use of higher concentrations of surfactant and glycerin, or microemulsion. The microemulsions used hampered the action of glyphosate in controlling B. brizantha and caused severe poisoning in corn, and these poisonings attributed mainly to the action of surfactant
Resumo:
The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation
Resumo:
The development of oil wells drilling requires additional cares mainly if the drilling is in offshore ultra deep water with low overburden pressure gradients which cause low fracture gradients and, consequently, difficult the well drilling by the reduction of the operational window. To minimize, in the well planning phases, the difficulties faced by the drilling in those sceneries, indirect models are used to estimate fracture gradient that foresees approximate values for leakoff tests. These models generate curves of geopressures that allow detailed analysis of the pressure behavior for the whole well. Most of these models are based on the Terzaghi equation, just differentiating in the determination of the values of rock tension coefficient. This work proposes an alternative method for prediction of fracture pressure gradient based on a geometric correlation that relates the pressure gradients proportionally for a given depth and extrapolates it for the whole well depth, meaning that theses parameters vary in a fixed proportion. The model is based on the application of analytical proportion segments corresponding to the differential pressure related to the rock tension. The study shows that the proposed analytical proportion segments reaches values of fracture gradient with good agreement with those available for leakoff tests in the field area. The obtained results were compared with twelve different indirect models for fracture pressure gradient prediction based on the compacting effect. For this, a software was developed using Matlab language. The comparison was also made varying the water depth from zero (onshore wellbores) to 1500 meters. The leakoff tests are also used to compare the different methods including the one proposed in this work. The presented work gives good results for error analysis compared to other methods and, due to its simplicity, justify its possible application
Resumo:
In this work, biodiesel was produced from castor oil that was a byproduct glycerin. The molar ratio between oil and alcohol, as well as the use of (KOH) catalyst to provide the chemical reaction is based on literature. The best results were obtained using 1 mol of castor oil (260g) to 3 moles of methyl alcohol (138g), using 1.0% KOH as catalyst at a temperature of 260 ° C and shaken at 120 rpm. The oil used was commercially available, the process involves the reaction of transesterification of a vegetable oil with methyl alcohol. The product of this reaction is an ester, biodiesel being the main product and the glycerin by-product which has undergone treatment for use as raw material for the production of allyl alcohol. The great advantage of the use of glycerin to obtain allyl alcohol is that its use eliminates the large amount of waste of the biodiesel and various forms of insult to the environment. The reactions for the formation of allyl alcohol was conducted from formic acid and glycerin in a ratio 1/1, at a temperature of 260oC in a heater blanket, being sprayed by a spiral condenser for a period of 2 hours and the product obtained contains mostly the allylic alcohol .. The monitoring of reactions was performed by UV-Visible Spectrophotometer: FTIR Fourier transform, the analysis showed that these changes occur spectrometer indicating the formation of the product allylic alcohol (prop-2-en-1-ol) in the presence of water, This alcohol was appointed Alcohol GL. The absorption bands confirms that the reaction was observed in (υ C = C) 1470 -1600 cm -1 and (υ CO), 3610-3670 attributed to C = C groups and OH respectively. The thermal analysis was carried out in a thermogravimetric analyzer SDT Q600, where the mass and temperature are displayed against time, that allows checking the approximate rate of heating. The innovative methodology developed in the laboratory (LABTAM, UFRN), was able to treat the glycerine produced by transesterification of castor oil and used as raw material for production of allyl alcohol, with a yield of 80%, of alcohol, the same is of great importance in the manufacture of polymers, pharmaceuticals, organic compounds, herbicides, pesticides and other chemicals
Resumo:
Aiming to reduce and reuse waste oil from oily sludge generated in large volumes by the oil industry, types of nanostructured materials Al-MCM-41 and Al-SBA-15, with ratios of Si / Al = 50, were synthesized , and calcined solids used as catalysts in the degradation of oily sludge thermocatalytic oil from oilfield Canto do Amaro, in the state of Rio Grande do Norte. Samples of nanostructured materials were characterized by thermogravimetric analysis (TG / DTG), X-ray diffraction (XRD), scanning electron microscopy (SEM), absorption spectroscopy in the infrared Fourier transform (FT-IR) and adsorption nitrogen (BET). The characterization showed that the synthesized materials resulted in a catalyst nanostructure, and ordered pore diameter and surface area according to existing literature. The oily sludge sample was characterized by determining the API gravity and sulfur content and SARA analysis (saturates, aromatics, resins and asphaltenes). The results showed a material equivalent to the average oil with API gravity of 26.1, a low sulfur content and considerable amount of resins and asphaltenes, presented above in the literature. The thermal and catalytic degradation of the oily sludge oil was performed from room temperature to 870 ° C in the ratios of heating of 5, 10 and 20 ° C min-1. The curves generated by TG / DTG showed a more accelerated degradation of oily sludge when it introduced the nanostructured materials. These results were confirmed by activation energy calculated by the method of Flynn-Wall, in the presence of catalysts reduced energy, in particular in the range of cracking, showing the process efficiency, mainly for extraction of lightweight materials of composition of oily sludge, such as diesel and gasoline
Resumo:
O Eucalyptus grandis é uma das espécies mais cultivadas no Brasil devido à sua produtividade e qualidade da madeira. Avaliaram-se o efeito da aplicação de lodo de esgoto tratado (0 a 40 t ha-1 base seca) e uma dose de adubo mineral nos atributos físicos e químicos da madeira de Eucalyptus grandis de árvores com cinco anos de idade, no Município de Itatinga, São Paulo, Brasil. O tipo de solo foi caracterizado como Latossolo Vermelho-Amarelo Distrófico (argila = 120 g kg-1 na camada de 0-20 cm) e o clima, como mesotérmico úmido (Cwa), segundo a classificação de Köeppen. O delineamento experimental foi o de blocos ao acaso, com seis tratamentos e quatro repetições. O diâmetro à altura do peito (DAP), a altura das árvores e o volume de madeira foram obtidos em todas as parcelas de oito árvores com DAP na classe de maior freqüência. As caracterizações físicas e químicas da madeira foram realizadas de acordo com as normas da ABTCP, TAPPI e ABNT. O lodo de esgoto diminuiu a densidade básica da madeira, mas não afetou os teores de celulose, lignina, extrativos e o poder calorífico da madeira. O decréscimo de densidade da madeira pela adubação com lodo de esgoto foi compensado pela maior produtividade de madeira.
Resumo:
Tamoxifen (TX), a drug used in the treatment of breast cancer, may cause hepatic changes in some patients. The consequences of its use on the liver tissues of rats with or without diabetes mellitus (DM) have not been fully explored. The purpose of this multidisciplinary study was to evaluate the correlation between plasma hepatic enzyme levels and the presence of iron overload in the hepatic tissue of female Wistar rats with or without streptozotocin-induced DM and using TX. Female rats were studied in control groups: C-0 (non-drug users), C-V (sorbitol vehicle only) and C-TX (using TX). DM (diabetic non-drug users) and DM-TX (diabetics using TX) were the test groups. Sixty days after induced DM, blood samples were collected for glucose, alanine aminotransferase (ALT), aspartate aminotransferase (AST) alkaline phosphatase (ALP) and bilirubin measures. Hepatic fragments were processed and stained with hematoxylin and eosin (H&E), Masson s trichrome, Perls. The hepatic iron content was quantified by atomic absorption spectrometry. AST, ALT and ALP levels were significantly elevated in the DM and DM-TX groups, with unchanged bilirubin levels. Liver iron overload using Perls stain and atomic absorption spectrometry were observed exclusively in groups C-TX and DM-TX. There was positive correlation between AST, ALT and ALP levels and microscopic hepatic siderosis intensity in group DM-TX. In conclusion, TX administration is associated with liver siderosis in diabetic and non-diabetic rats. In addition, TX induced liver iron overload with unaltered hepatic function in 2 non-diabetic rats and may be a useful tool for investigating the biological control of iron metabolism
Resumo:
The contribution of green manure to soil improvement and crop production depends primarily on biomass production and its chemical composition, which vary depending on the species, region and growing season. The aim of this research was to evaluate the chemical composition of biomass produced by green manures in Vale do Ribeira, São Paulo, Brazil. In order to develop this research, was carried an experiment in Pariquera-Acu, in 2006/2007, in completely randomized blocks design with four treatments (three green manure and spontaneous vegetation) and five replications. At 30, 60, 90 and 120 after sowing samples were collected in 1m(2) of the shoots and determined fresh and dry, and chemical composition biomass. Sunhemp, pigeon pea and mucuna produced, in decreasing order, the largest quantities of biomass and were more efficient than the spontaneous vegetation. The biomass produced by green manure had higher quality than that produced by spontaneous vegetation. Sunhemp and pigeon pea have a higher proportion of dry matter in stems which have low N, high C/N and L/N ratio, variables indicating slow decomposition of residues. The analysis of dry matter partitioned to better indication of the chemical composition of the residues and the prevision of the availability of nutrients in the soil.
Resumo:
O conhecimento sobre o crescimento e o acúmulo de nutrientes em hipobiotos de caramboleira permite melhor eficiência da adubação na produção de hipobiotos (porta-enxertos). Objetivou-se determinar o crescimento e o acúmulo de nutrientes em hipobiotos de caramboleira cultivada em solução nutritiva. O experimento constituiu de cinco tratamentos, referentes aos tempos de coleta 25; 50; 75; 100 e 125 dias após o transplantio, dispostos em delineamento inteiramente casualizado em seis repetições. As plantas utilizadas foram obtidas de sementes de frutos de caramboleira 'Malásia', cultivadas em vasos com solução nutritiva. Nos diferentes órgãos dos hipobiotos (folhas, caule e raízes), avaliou-se o crescimento e o acúmulo de nutrientes e os índices nutricionais, a cada 25 dias. O ponto de enxertia (6 mm) foi atingido aos 110 dias após o transplantio. A ordem decrescente dos nutrientes acumulados em cada hipobioto produzido é de (em mg por planta): N = 634; K = 368; Ca = 152; Mg = 106; S = 98; P = 88 (em µg por planta) de: Fe = 2.963; Mn = 2.165; B = 722; Zn =780, e Cu = 96. O acúmulo médio de nutrientes é maior nas folhas > caule = raízes. O período de maior exigência de nutrientes pelos hipobiotos é compreendido entre 25-75 dias após o transplantio. As diferentes taxas de acumulação líquida dos nutrientes, nas diferentes partes da caramboleira, nem sempre acompanham a taxa de acumulação de nutrientes do respectivo órgão.
Resumo:
The aim of this work was to perform the extraction and characterization of xylan from corn cobs and prepare xylan-based microcapsules. For that purpose, an alkaline extraction of xylan was carried out followed by the polymer characterization regarding its technological properties, such as angle of repose, Hausner factor, density, compressibility and compactability. Also, a low-cost and rapid analytical procedure to identify xylan by means of infrared spectroscopy was studied. Xylan was characterized as a yellowish fine powder with low density and poor flow properties. After the extraction and characterization of the polymer, xylan-based microcapsules were prepared by means of interfacial crosslinking polymerization and their characterization was performed in order to obtain gastroresistant multiparticulate systems. This work involved the most suitable parameters of the preparation of microcapsules as well as the study of the process, scale-up methodology and biological analysis. Magnetic nanoparticles were used as a model system to be encapsulated by the xylan microcapsules. According to the results, xylan-based microcapsules were shown to be resistant to several conditions found along the gastrointestinal tract and they were able to avoid the early degradation of the magnetic nanoparticles
Resumo:
The aim of this study was to assess the acute and chronic effects of zinc in serum iron profile of children aged 6-9 years in relation to nutritional status and dietary intake. The study participants were 11 children regardless of sex, aged 6-9 years. They were selected from three public schools of the city of Natal, Brazil. Body mass index was used to assess nutritional status. In order to determine the patterns of childhood growth and ideal weight we used the standards of the World Health Organization. The dietary intake assessment was based on information from a three-day prospective food survey. The variables were energy intake, protein, lipids, carbohydrates, fiber, calcium, iron and zinc. All children underwent an intravenous administration of zinc (IVAZn) before and after oral administration of zinc (OAZn) (5 mg Zn / day) for three months. We measured serum iron, hematocrit, hemoglobin and total protein, before and after the use of oral zinc. The analysis of hematocrit, hemoglobin and total protein was performed using standard methods of clinical laboratory. Zinc levels and serum iron were measured by atomic absorption spectrophotometry. The project was evaluated and approved by the Ethics in Research Committee of Federal University of Rio Grande do Norte. Results: All children had normal weight. The consumption of energy, fat, fiber, calcium and iron were below recommended levels. However, the levels of protein and carbohydrates were high. Protein and zinc increased significantly after OAZn. Carbohydrate and protein were elevated in the blood. After OAZn, both protein and zinc increased, being statistically significant. Conclusion: The potential inhibitory effect of physiological or pharmacological doses of zinc on the profile of serum iron was observed in children with healthy weight and aged between 6 and 9 years. This negative effect of zinc did not affect the levels of hematocrit or hemoglobin, and therefore did not cause anemia. This was a multidisciplinary study, involving researchers from medicine, nutrition and pharmacy. This met the requirements of multidisciplinarity of the Post Graduate Program in Health Sciences of Federal University of Rio Grande do Norte.
Resumo:
Although many studies point to alterations in the organic concentrations of zinc in elderly patients, the mechanisms by which aging might cause changes in the metabolism of this nutrient remain unclear. Thus, we assessed the changes in plasma zinc, Zinc Binding Capacity to Plasma Protein (ZnBCPP) and Saturation Index (SI), comparing elderly individuals and young adults. The zinc analyses were performed by atomic absorption spectrophotometry. A statistically significant difference (p < 0.001) was found between the two groups, in relation to plasma zinc and SI, but the ZnBCPP did not differ between the younger and older subjects. In agreement with this result, it was shown in the young group that 76% (R2 = 0.760) of the ZnBCPP variations are explained by the variations in plasma zinc and SI. In the elderly group this measure decreased to 30.5% (R2 = 0.305). We conclude, therefore, that aging may be a factor associated to changes in control mechanisms and in zinc homeostasis, and could even alter ZnBCPP response patterns and other zinc-related indicators of nutritional status.
Resumo:
Thiamethoxam is a systemic insecticide from the neonicotinoid group, nitroguanidin family which affects the nicotinic receptor acetyl choline in the insect membrane, wounding the nervous system and causing the death of the insect. It was used with success in the control of initial pests of several crops. It was considered that thiamethoxam has a bioactivator effect, because in the absence of insects promoted increase in vigor, development and productivity of crops. This work was carried out to verify if thiamethoxam causes histological changes in sugarcane roots. In this work, it was used optical microscopy, images arrest, tissue biometrics and statistical analysis, in young roots of sugarcane RB 83 5486 after the treatments with different thiamethoxam concentrations. It was determined changes in histological structure of tissues 7, 14, 21 and 28 days after the treatments, establishing its effects on root plant anatomy. It was verified that thiamethoxam increased root cortex width, increasing the vascular cylinder and the metaxylem vessel elements number in the vascular tissue until 21 days after application.