Light absorption and electrical transport in Si:O alloys for photovoltaics

Thin films (100-500 nm) of the Si:O alloy have been systematically characterized in the optical absorption and electrical transport behavior, by varying the Si content from 43 up to 100 at. %. Magnetron sputtering or plasma enhanced chemical vapor deposition have been used for the Si:O alloy deposition, followed by annealing up to 1250 °C. Boron implantation (30 keV, 3-30× 1014 B/cm2) on selected samples was performed to vary the electrical sheet resistance measured by the four-point collinear probe method. Transmittance and reflectance spectra have been extracted and combined to estimate the absorption spectra and the optical band gap, by means of the Tauc analysis. Raman spectroscopy was also employed to follow the amorphous-crystalline (a-c) transition of the Si domains contained in the Si:O films. The optical absorption and the electrical transport of Si:O films can be continuously and independently modulated by acting on different parameters. The light absorption increases (by one decade) with the Si content in the 43-100 at. % range, determining an optical band gap which can be continuously modulated into the 2.6-1.6 eV range, respectively. The a-c phase transition in Si:O films, causing a significant reduction in the absorption coefficient, occurs at increasing temperatures (from 600 to 1100 °C) as the Si content decreases. The electrical resistivity of Si:O films can be varied among five decades, being essentially dominated by the number of Si grains and by the doping. Si:O alloys with Si content in the 60-90 at. % range (named oxygen rich silicon films), are proved to join an appealing optical gap with a viable conductivity, being a good candidate for increasing the conversion efficiency of thin-film photovoltaic cell. © 2010 American Institute of Physics.

武汉东湖沉积物中重金属生物有效性研究

沉积物中的酸挥发性硫化物(AVS)是预测厌氧沉积物中重金属生物有效性的重要参数,SEM/AVS大于1时沉积物中重金属具有潜在生物毒性,小于1时则无生物有效性. 本文研究了东湖三个不同污染负荷的站点的同步提取金属SEM(Cu, Zn, Pb, Cd, Ni, Co, Ag, Cr)和SEM/AVS的深度分布,研究表明东湖沉积物中主要重金属是Zn, Cr和Cu,约占SEM总量的90%. I站、II站沉积物中AVS是重金属生物有效性的主控因子之一,对重金属的深度分布影响较大,重金属不具有生物有效性;III站沉积

A graphene-based large area surface-conduction electron emission display

The fabrication and functionality of a 21 cm graphene-based transverse electron emission display panel is presented. A screen-printed triode edge electron emission geometry has been developed based on chemical vapor deposited (CVD) graphene supported on vertically aligned carbon nanotubes (CNT) necessary to minimize electrostatic shielding induced by the proximal bulk substrate. Integrated ZnO tetrapod electron scatterers have been shown to increase the emission efficiency by more than 90%. Simulated electron trajectories validate the observed emission characteristics with driving voltages less than 60 V. Fabricated display panels have shown real-time video capabilities that are hysteresis free (<0.2%), have extremely stable lifetimes (<3% variation over 10 h continuous operation) in addition to rapid temporal responses (<1 ms). © 2013 Elsevier Ltd. All rights reserved.

Magnetocaloric effect in nano- and polycrystalline manganite La 0.7Ca0.3MnO3

La0.7Ca0.3MnO3 samples were prepared in nano- and polycrystalline forms by the sol-gel and solid state reaction methods, respectively, and structurally characterized by synchrotron X-ray diffraction. The magnetic properties determined by ac susceptibility and dc magnetization measurements are discussed. The magnetocaloric effect in this nanocrystalline manganite is spread over a broader temperature interval than in the polycrystalline case. The relative cooling power of the poly- and nanocrystalline manganites is used to evaluate a possible application for magnetic cooling below room temperature. © 2007 Springer-Verlag.

Integrated high pressure microhydraulic actuation and control for surgical instruments

To reduce the surgical trauma to the patient, minimally invasive surgery is gaining considerable importance since the eighties. More recently, robot assisted minimally invasive surgery was introduced to enhance the surgeon's performance in these procedures. This resulted in an intensive research on the design, fabrication and control of surgical robots over the last decades. A new development in the field of surgical tool manipulators is presented in this article: a flexible manipulator with distributed degrees of freedom powered by microhydraulic actuators. The tool consists of successive flexible segments, each with two bending degrees of freedom. To actuate these compliant segments, dedicated fluidic actuators are incorporated, together with compact hydraulic valves which control the actuator motion. Especially the development of microvalves for this application was challenging, and are the main focus of this paper. The valves distribute the hydraulic power from one common high pressure supply to a series of artificial muscle actuators. Tests show that the angular stroke of the each segment of this medical instrument is 90°. © 2012 Springer Science+Business Media, LLC.

活性藻系统对氮、磷及有机物的去除研究

报道了实验室条件下利用活性藻反应系统对合成污水中N、P、CODCr和BOD5等的去除 效果.在26±2℃条件下,当停留时间为24h时,TN, TP, CODCr 和BOD5 的平均去除率分别为 7 7.62%, 33.23%, 90.89% 和 95.77%.当进水负荷加大一倍、停留时间相应缩短、光强、水温 同时减弱和降低时,该系统对TP 和BOD5的处理效果受到明显影响,对 CODCr的处理效果影响 不大,运行条件的改变基本上不影响活性藻系统对TN的处理效果,两种运行条件下,TN的平均 去除率分别为77

Numerical simulation of post-flame oxidation of hydrocarbons in spark ignition engines

About 50-90 percent of the hydrocarbons that escape combustion during flame passage in spark-ignition engine operation are oxidized in the cylinder before leaving the system. The process involves the transport of unreacted fuel from cold walls towards the hotter burned gas regions and subsequent reaction. In order to understand controlling factors in the process, a transient one-dimensional reactive-diffusive model has been formulated for simulating the oxidation processes taking place in the reactive layer between hot burned gases and cold unreacted air/fuel mixture, with initial and boundary conditions provided by the emergence of hydrocarbons from the piston top land crevice. Energy and species conservation equations are solved for the entire process, using a detailed chemical kinetic mechanism for propane. Simulation results show that the post-flame oxidation process takes place within a reactive layer where intermediate hydrocarbon products are formed at temperatures above 1100-1200 K, followed by a carbon monoxide conversion region closer to the hot burned gases. Model results show that most of hydrocarbons leaving the crevice are completely oxidized inside the cylinder. The largest contribution of remaining hydrocarbons are those leaving the crevice at temperatures below 1400 K. The largest fraction of non-fuel (intermediate) hydrocarbons results from hydrocarbons leaving the crevice when core temperatures are around 1400 K Copyright © 1997 Society of Automotive Engineers, Inc.

The smallest thermal nuclear reactor

There is a growing need for very small nuclear reactors for space applications and as portable high-intensity neutron sources. This technical note investigates the question of what is the smallest possible thermal reactor. It was found that the smallest reactor is a spherically shaped solution of 242mAm(NO3)3 in water. The weight of such a reactor is 4.95 kg with 0.7 kg of 242mAm nuclear fuel. The radius of the reactor in this case is 9.6 cm.

Ultra-thin 242mAm fuel elements in nuclear reactors

There is a growing interest in using 242mAm as a nuclear fuel. The advantages of 242mAm as a nuclear fuel derive from the fact that 242mAm has the highest thermal fission cross section. The thermal capture cross section is relatively low and the number of neutrons per thermal fission is high. These nuclear properties make it possible to obtain nuclear criticality with ultra-thin fuel elements. The possibility of having ultra-thin fuel elements enables the use of these fission products directly, without the necessity of converting their energy to heat, as is done in conventional reactors. There are three options of using such highly energetic and highly ionized fission products. 1. Using the fission products themselves for ionic propulsion. 2. Using the fission products in an MHD generator, in order to obtain electricity directly. 3. Using the fission products to heat a gas up to a high temperature for propulsion purposes. In this work, we are not dealing with a specific reactor design, but only calculating the minimal fuel elements' thickness and the energy of the fission products emerging from these fuel elements. It was found that it is possible to design a nuclear reactor with a fuel element of less than 1 μm of 242mAm. In such a fuel element, 90% of the fission products' energy can escape.

Taper-free and vertically oriented Ge nanowires on Ge/Si substrates grown by a two-temperature process

Taper-free and vertically oriented Ge nanowires were grown on Si (111) substrates by chemical vapor deposition with Au nanoparticle catalysts. To achieve vertical nanowire growth on the highly lattice mismatched Si substrate, a thin Ge buffer layer was first deposited, and to achieve taper-free nanowire growth, a two-temperature process was employed. The two-temperature process consisted of a brief initial base growth step at high temperature followed by prolonged growth at lower temperature. Taper-free and defect-free Ge nanowires grew successfully even at 270 °C, which is 90 °C lower than the bulk eutectic temperature. The yield of vertical and taper-free nanowires is over 90%, comparable to that of vertical but tapered nanowires grown by the conventional one-temperature process. This method is of practical importance and can be reliably used to develop novel nanowire-based devices on relatively cheap Si substrates. Additionally, we observed that the activation energy of Ge nanowire growth by the two-temperature process is dependent on Au nanoparticle size. The low activation energy (∼5 kcal/mol) for 30 and 50 nm diameter Au nanoparticles suggests that the decomposition of gaseous species on the catalytic Au surface is a rate-limiting step. A higher activation energy (∼14 kcal/mol) was determined for 100 nm diameter Au nanoparticles which suggests that larger Au nanoparticles are partially solidified and that growth kinetics become the rate-limiting step. © 2011 American Chemical Society.

~(90)锶对鲫鱼胚胎发育的影响及鲫仔鱼对~(90)锶吸收积累的研究

在胚胎发育过程中,用不同比放射性的~(90)锶试液处理受精卵,各处理组都有畸形和死亡现象。畸形的高峰一般出现在囊胚期和晶体形成期,畸形的类型一般为脊椎弯曲、体短、胸腔和卵黄囊扩大,头和眼畸形。随后即出现死亡高峰。例如:游动期的死亡率分别是:21%(对照);36%(5×10~(-11)居里/升);40%(5×1-~(-10)居里/升);45%(5×10~(-9)居里/升)。鲫仔鱼对~(90)锶吸收积累的结果表明:鲫仔鱼体中比放射性大小与试液的比放射性大小成正比,并随试验吋间的延长,生物量的增加而增加,鲫仔鱼

固定化假单胞菌CTP-01细胞分解对硫磷的研究

用明胶-戊二醛(GGA)和聚丙烯酰胺(PAA)包埋的固定化Pseudomonas sp.CTP-01细胞具有降解对硫磷的特性。GGA固定化细胞水解对硫磷的活力比PAA固定化细胞高5.8倍。当保存在4℃时GGA和PAA固定化细胞分别可以保持活力31.3和70%。GGA和PAA包埋的细胞最适反应温度分别为50℃到70℃和60℃到70℃,然而整细胞在温度超过65℃时活力很快下降。GGA和PAA两种固定化细胞最适pH为8.0,当pH低于7.0时活力开始下降,pH4吋则完全失活。

草鱼血液学的研究 Ⅰ.九项血液常数的周年变化

用741尾健康草鱼种作红细胞、血红蛋白、红细胞比积、红细胞平均体积、红细胞平均血红蛋白量、红细胞平均血红蛋白浓度、红细胞沉降率、血浆总蛋白和血浆葡萄糖浓度等九项血液常数的测定。所得的年均值经变异系数分析,除红细胞沉降率和血浆葡萄糖浓度外,其余各项常数的可靠性基本一致。另从周年变动的规律分析,高值出现在冬夏季,低值出现的月份较为分散。水温仅对总蛋白含量的变动呈现显著的负相关(P<0.01)。而体重与血液常数存在着一定的相关因素,在10—90克之间的鱼种中,血红蛋白、红细胞比积、红细胞平均体积、红细胞平均血红

Stretching-assembled nanowires for organic-based thin film transistors

We demonstrate a stretched contact-printing technique to assemble one-dimensional nanostructures with controlled density and orientation. Over 90% nanowires are highly aligned along the primary stretching direction. Specifically, The hybrid inorganic-organic TFTs based on a parallel-aligned nanowire network and a semiconducting polymer reveal a significant positive enhancement in transistor performance and air-stability.

有机磷农药在水生态系中生物净化机理研究---- ----4. Pseudomonas sp. CTP-01 的对硫磷水解酶诱导合成性质

Pseudomonas sp.CTP-01的对硫磷水解酶具有底物诱导合成性质。停滞生长期的细胞接触底物半小时即产生相应酶的合成,而指数生长期的细胞接触底物48小时后才发生酶的合成。甲基对硫磷及对硝基酚也具有诱导作用,可见合成对硫磷水解酶的诱导特异基团可能与对硝基酚及其苯环上的取代基有密切关系。