Injection Locked Clocking and Transmitter Equalization Techniques for Chip to Chip Interconnects

Semiconductor technology scaling has enabled drastic growth in the computational capacity of integrated circuits (ICs). This constant growth drives an increasing demand for high bandwidth communication between ICs. Electrical channel bandwidth has not been able to keep up with this demand, making I/O link design more challenging. Interconnects which employ optical channels have negligible frequency dependent loss and provide a potential solution to this I/O bandwidth problem. Apart from the type of channel, efficient high-speed communication also relies on generation and distribution of multi-phase, high-speed, and high-quality clock signals. In the multi-gigahertz frequency range, conventional clocking techniques have encountered several design challenges in terms of power consumption, skew and jitter. Injection-locking is a promising technique to address these design challenges for gigahertz clocking. However, its small locking range has been a major contributor in preventing its ubiquitous acceptance.

In the first part of this dissertation we describe a wideband injection locking scheme in an LC oscillator. Phase locked loop (PLL) and injection locking elements are combined symbiotically to achieve wide locking range while retaining the simplicity of the latter. This method does not require a phase frequency detector or a loop filter to achieve phase lock. A mathematical analysis of the system is presented and the expression for new locking range is derived. A locking range of 13.4 GHz–17.2 GHz (25%) and an average jitter tracking bandwidth of up to 400 MHz are measured in a high-Q LC oscillator. This architecture is used to generate quadrature phases from a single clock without any frequency division. It also provides high frequency jitter filtering while retaining the low frequency correlated jitter essential for forwarded clock receivers.

To improve the locking range of an injection locked ring oscillator; QLL (Quadrature locked loop) is introduced. The inherent dynamics of injection locked quadrature ring oscillator are used to improve its locking range from 5% (7-7.4GHz) to 90% (4-11GHz). The QLL is used to generate accurate clock phases for a four channel optical receiver using a forwarded clock at quarter-rate. The QLL drives an injection locked oscillator (ILO) at each channel without any repeaters for local quadrature clock generation. Each local ILO has deskew capability for phase alignment. The optical-receiver uses the inherent frequency to voltage conversion provided by the QLL to dynamically body bias its devices. A wide locking range of the QLL helps to achieve a reliable data-rate of 16-32Gb/s and adaptive body biasing aids in maintaining an ultra-low power consumption of 153pJ/bit.

From the optical receiver we move on to discussing a non-linear equalization technique for a vertical-cavity surface-emitting laser (VCSEL) based optical transmitter, to enable low-power, high-speed optical transmission. A non-linear time domain optical model of the VCSEL is built and evaluated for accuracy. The modelling shows that, while conventional FIR-based pre-emphasis works well for LTI electrical channels, it is not optimum for the non-linear optical frequency response of the VCSEL. Based on the simulations of the model an optimum equalization methodology is derived. The equalization technique is used to achieve a data-rate of 20Gb/s with power efficiency of 0.77pJ/bit.

1.55-μm VCSEL transmission performance up to 20 Gb/s for access networks

We experimentally demonstrate for the first time 1.55μm vertical-cavity surface-emitting laser (VCSEL) transmission over 6.5 km single mode fiber (SMF) at 20 Gb/s for optical access networks. Characterization of the device is also investigated. © 2009 IEEE.

32 Gb/s multilevel modulation of an 850 nm VCSEL for next-generation datacommunication standards

An 850 nm vertical-cavity surface-emitting laser is modulated at 32 Gb/s using pulse-amplitude modulation with four levels. Transmitter predistortion generates an optimized modulation waveform, which requires a receiver bandwidth of only 15 GHz. © 2011 OSA.

A CMOS analogue predistortion circuit for wideband optical fibre links

The laser is a major source of nonlinearity for optical fibre communication systems. In this paper, we propose a CMOS analogue predistortion circuit to reduce laser nonlinearity for wideband optical fibre links. The circuit uses a nonlinearity having the inverse transfer characteristic of the directly modulated vertical cavity surface emitting laser (VCSEL). It is shown by post-layout simulation that the predistortion circuit shows 12dBm improvement in the optical fibre system. The optical fibre transmitter front-end with predistortion lineariser is being fabricated using the austriamicrosystems (AMS) 0.3 5μm CMOS technology.

28 Gb/s unequalized PAM3 modulation of an 850 nm VCSEL for next-generation datacommunication links

An 850 nm vertical-cavity surface-emitting laser is modulated at 28 Gb/s using pulseamplitude modulation with three levels. Unequalized transmission over 100 m of OM3 MMF is demonstrated, with advantages over NRZ and PAM4 modulation. © 2012 OSA.

28 Gb/s unequalized PAM3 modulation of an 850 nm VCSEL for next-generation datacommunication links

An 850 nm vertical-cavity surface-emitting laser is modulated at 28 Gb/s using pulseamplitude modulation with three levels. Unequalized transmission over 100 m of OM3 MMF is demonstrated, with advantages over NRZ and PAM4 modulation. © OSA 2012.

32 Gb/s multilevel modulation of an 850 nm VCSEL for next-generation datacommunication standards

An 850 nm vertical-cavity surface-emitting laser is modulated at 32 Gb/s using pulseamplitude modulation with four levels. Transmitter predistortion generates an optimized modulation waveform, which requires a receiver bandwidth of only 15 GHz. © OSA/ CLEO 2011.

The application of parallel optical transmitter and receiver modules in communication subsystems

A new 12 channels parallel optical transmitter module in which a Vertical Cavity Surface Emitting Laser (VCSEL) has been selected as the optical source is capable of transmitting 37.5Gbps date over hundreds meters. A new 12 channels parallel optical receiver module in which a GaAs PIN (p-intrinsic-n-type) array has been selected as the optical receiver unit is capable of responding to 30Gbps date. A transmission system based on a 12 channels parallel optical transmitter module and a 12 channels parallel optical receiver module can be used as a 10Gbps STM-64 or an OC-192 optical transponder. The parallel optical modules and the parallel optical transmission system have passed the test in laboratory.

VCSEL-based parallel optical transmission module

This paper describes the design process and performance of the optimized parallel optical transmission module. Based on 1x12 VCSEL (Vertical Cavity Surface Emitting Laser) array, we designed and fabricated the high speed parallel optical modules. Our parallel optical module contains a 1x12 VCSEL array, a 12 channel CMOS laser driver circuit, a high speed PCB (Printed Circuit Board), a MT fiber connector and a packaging housing. The L-I-V characteristics of the 850nm VCSEL was measured at the operating current 8mA, 3dB frequency bandwidth more than 3GHz and the optical output 1mW. The transmission rate of all 12 channels is 30Gbit/s, with a single channel 2.5Gbit/s. By adopting the integration of the 1x12 VCSEL array and the driver array, we make a high speed PCB (Printed Circuit Board) to provide the optoelectronic chip with the operating voltage and high speed signals current. The LVDS (Low-Voltage Differential Signals) was set as the input signal to achieve better high frequency performance. The active coupling was adopted with a MT connector (8 degrees slant fiber array). We used the Small Form Factor Pluggable (SFP) packaging. With the edge connector, the module could be inserted into the system dispense with bonding process.

High Speed VCSEL-Based Parallel Optical Transmission Modules

Design and fabrication of a parallel optical transmitter are reported. The optimized 12 channel parallel optical transmitter,with each channel＇s data rate up to 3Gbit/s,is designed, assembled, and measured. A top-emitting 850nm vertical cavity surface emitting laser（VCSEL） array is adopted as the light source,and the VCSEL chip is directly wire bonded to a 12 channel driver IC. The outputs of the VCSEL array are directly butt coupled into a 12 channel fiber array. Small form factor pluggable （SFP） packaging technology is used in the module to support hot pluggable in application. The performance results of the module are demonstrated. At an operating current of 8mA, an eye diagram at 3Gbit/s is achieved with an optical output of more than 1mW.

1.55-μm Si-based MOEMS optical tunable filter

A prototype 1.55-μm Si-based micro-opto-electro-mechanical-systems (MOEMS) tunable filter is fabricated, employing surface micromachining technology. Full-width-at-half-maximum (FWHM) of the transmission spectrum is 23 nm. The tuning range is 30 nm under 50-V applied voltage. The device can be readily integrated with resonant cavity enhanced (RCE) detector and vertical cavity surface emitting laser (VCSEL) to fabricate tunable active devices.

10Gbit/s甚短距离(VSR)并行光传输系统

介绍了一个适用于甚短距离(Very Short Reach,VSR)网络传输的并行光传输系统。系统的发射部分用垂直腔面发射激光器(vERTICAL cAVITY sURFACE eMITTING lASER,vcsel)1×12列阵代替传统的边发射激光器，接收部分也采用相应的探测器列阵，并由多模光纤列阵相连接，在300m距离内以单信道1．25Gbit/s速率实现的10Gbit/s的高传输速率。

16-channel 0.35 mu m CMOS/VCSEL optoelectronic devices

We report some investigations on vertical cavity surface emitting laser (VCSEL) arrays and VCSEL based optoelectronic smart photonic multiple chip modules (MCM), consisting of 1 x 16 vertical cavity surface emitting laser array and 16-channel lasers driver 0.35 mum CMOS circuit. The hybrid integrated multiple chip modules based on VCSEL operate at more than 2GHz in -3dB frequency bandwidth.

Hybrid CMOS/VCSEL optoelectronic modules

We report some investigations on vertical cavity surface emitting laser (VCSEL) arrays and VCSEL based optoelectronic smart photonic multiple chip modules (MCM), consisting of 1x16 vertical cavity surface emitting laser array and 16-channel lasers driver 0.35 Pin CMOS circuit. The hybrid integrated multiple chip modules based on VCSEL operate at more than 2GHz in -3dB frequency bandwidth.

VCSEL based optoelectronic multiple chip modules

We report on optoelectronic multiple chip modules, consisting of vertical cavity surface emitting laser(VCSEL), photodetector and 1.2 mum CMOS electronic circuit, The hybrid integrated components operate at a date rate of 155Mb/s, which could be used in optical interconnects for multiple computers.