Perfomance evaluation of a direct injection engine using different blends of soybean (Glycine max) methyl biodiesel

Diesel fuel is used widely in Brazil and worldwide. On the other hand, the growing environmental awareness leads to a greater demand for renewable energy resources. Thus, this study aimed to evaluate the use of different blends of soybean (Glycine max) methyl biodiesel and diesel in an ignition compression engine with direct injection fuel. The tests were performed on an electric eddy current dynamometer, using the blends B10, B50 and B100, with 10; 50 e 100% of biodiesel, respectively, in comparison to the commercial diesel B5, with 5% of biodiesel added to the fossil diesel. The engine performance was analyzed trough the tractor power take off (PTO) for each fuel, and the best results obtained for the power and the specific fuel consumption, respectively, were: B5 (44.62 kW; 234.87 g kW-1 h-1); B10 (44.73 kW; 233.78 g kW-1 h-1); B50 (44.11 kW; 250.40 g kW-1 h-1) e B100 (43.40 kW; 263.63 g kW-1 h-1). The best performance occurred with the use of B5 and B10 fuel, without significant differences between these blends. The B100 fuel showed significant differences compared to the other fuels.

Use of blends of bioabsorbable poly(L-lactic acid)/poly(hydroxybutyrate- co-hydroxyvalerate) as surfaces for Vero cell culture

Vero cells, a cell line established from the kidney of the African green monkey (Cercopithecus aethiops), were cultured in F-10 Ham medium supplemented with 10% fetal calf serum at 37°C on membranes of poly(L-lactic acid) (PLLA), poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) and their blends in different proportions (100/0, 60/40, 50/50, 40/60, and 0/100). The present study evaluated morphology of cells grown on different polymeric substrates after 24 h of culture by scanning electron microscopy. Cell adhesion was also analyzed after 2 h of inoculation. For cell growth evaluation, the cells were maintained in culture for 48, 120, 240, and 360 h. For cytochemical study, the cells were cultured for 120 or 240 h, fixed, processed for histological analysis, and stained with Toluidine blue, pH 4.0, and Xylidine ponceau, pH 2.5. Our results showed that cell adhesion was better when 60/40 and 50/50 blends were used although cells were able to grow and proliferate on all blends tested. When using PLLA/PHBV (50/50) slightly flattened cells were observed on porous and smooth areas. PLLA/PHBV (40/60) blends presented flattened cells on smooth areas. PLLA/PHBV (0/100), which presented no pores, also supported spreading cells interconnected by thin filaments. Histological sections showed that cells grew as a confluent monolayer on different substrates. Cytochemical analysis showed basophilic cells, indicating a large amount of RNA and proteins. Hence, we detected changes in cell morphology induced by alterations in blend proportions. This suggests that the cells changed their differentiation pattern when on various PLLA/PHBV blend surfaces.

Osmotic dehydration of sweet potato (Ipomoea batatas) in ternary solutions

The aim of this work was to evaluate the osmotic dehydration of sweet potato (Ipomoea batatas) using hypertonic sucrose solutions, with or without NaCl, at three different concentrations, at 40 °C. Highest water losses were obtained when the mixture of sucrose and NaCl was used. The addition of NaCl to osmotic solutions increases the driving force of the process and it is verified that the osmotic dehydration process is mainly influenced by changes in NaCl concentration, but the positive effect of the salt-sucrose interaction on soluble solids also determined the decrease of solid gain when solutes were at maximum concentrations. Mass transfer kinetics were modeled according to Peleg, Fick and Page's equations, which presented good fittings of the experimental data. Peleg's equation and Page's model presented the best fitting and showed excellent predictive capacity for water loss and salt gain data. The effective diffusivity determined using Fick's Second Law applied to slice geometry was found to be in the range from 3.82 x 10-11 to 7.46 x 10-11 m²/s for water loss and from 1.18 x 10-10 to 3.38 x 10-11 m²/s for solid gain.

Effect of different sweetener blends and fat types on ice cream properties

The development of processed foods requires the understanding of the phenomena that dictate the ingredient interactions normally used in food formulations, as well as the effects of the numerous operations involved in the processing of the final product. In ice creams, sugars are responsible for taste, but they also affect the freezing behavior and viscosity of processed mixes. Components such as fats influence mechanical properties, melting resistance, and palatability of final products. The objective was to study the technological effects of different sugars and fats on the structure of ice cream formulations. Fructose syrup was used as a substitute for glucose syrup in blends with sucrose, and palm fat was employed as an alternative to hydrogenated vegetable fat. The analysis of variance showed significant differences in chemical compositions. Hygroscopicity of fructose syrup increased the solids content in the formulations. Melting rate and overrun were higher in products added with this sugar. Palm fat caused changes in melting ranges of formulations, and higher melting rate was observed in the combination of palm fat and fructose syrup.

Phase transitions in biodegradable films based on blends of gelatin and poly (vinyl alcohol)

The aim of this work was to study the effect of the hydrolysis degree (HD) and the concentration (C PVA) of two types of poly (vinyl alcohol) (PVA) and the effect of the type and the concentration of plasticizers on the phase properties of biodegradable films based on blends of gelatin and PVA, using a response-surface methodology. The films were made by casting and the studied properties were their glass (Tg) and melting (Tm) transition temperatures, which were determined by diferential scanning calorimetry (DSC). For the data obtained on the first scan, the fitting of the linear model was statistically significant and predictive only for the second melting temperature. In this case, the most important effect on the second Tm of the first scan was due to the HD of the PVA. In relation to the second scan, the linear model could be fit to Tg data with only two statistically significant parameters. Both the PVA and plasticizer concentrations had an important effect on Tg. Concerning the second Tm of the second scan, the linear model was fit to data with two statistically significant parameters, namely the HD and the plasticizer concentration. But, the most important effect was provoked by the HD of the PVA.

Some functional characteristics of extruded blends of fiber from sugarcane bagasse, whey protein concentrate, and corn starch

Blends of fiber from sugar cane bagasse, corn starch, and whey protein concentrate were extruded. A single screw extruder, equipped with a screw at a constant compression ratio of 1:1 and a die diameter of 3 mm, was used. The best processing conditions were determined according to a central composite rotatable design (α = 1.41) with 5 central points, which gives a total of 13 tests. During the extrusion process the content of insoluble fiber decreased and that of soluble fiber increased. An increase in the contents of fiber and in the barrel temperature resulted in a decrease in the expansion index values and an increase in the water absorption index values; whereas in blends with intermediate fiber contents the effects in these parameters were found to be the opposite. High fiber contents increased penetration force but decreased luminosity, water solubility index values and the adhesive force in gels. The extrusion process improved the functional properties of sugarcane fiber bagasse enabling its addition to diverse alimentary systems.

Effects of processing on physical properties of extruded snacks with blends of sour cassava starch and flaxseed flour

The opportunity to supplement common cassava biscuits with a product of higher nutritional value meets consumer expectations. In this work it was studied the effects of process parameters and flaxseed addition on physical properties of expanded snacks. Extrusion process was carried out using a single screw extruder in a factorial central composite rotatable design with four factors: flaxseed flour percentage (0-20%), moisture (12-20%), extrusion temperature (90-130 °C) and screw speed (190-270). The effect of extrusion variables was investigated in terms of expansion index, specific volume, water absorption index, water solubility index, color parameters (L*, a* ,b*) and hardness. The data analysis showed that variable parameters of the extrusion process and flaxseed flour affected physical properties of puffed snacks. Among the experimental conditions used in the present study, expanded snack products with good physical properties can be obtained under the conditions of 10% flaxseed flour, 230 rpm screw speed, temperature of 90 °C and moisture of 12%.

Extrusion of blends of cassava leaves and cassava flour: physical characteristics of extrudates

A cassava-based puffed snack was produced using a single screw extruder to determine the effect of the raw material composition (cassava leaf flour and moisture) and the process parameters (extrusion temperature and screw speed) on the physical characteristics of an extruded-expanded snack. A central composite rotational design, including four factors with 30 treatments, was used with the following as dependent variables: expansion index, specific volume, water solubility index, water absorption index, color (L*, a*, b*), and hardness. Under conditions of low moisture content (12 to 14%), low percentage of cassava leaf flour (2 to 4%), and intermediate conditions of extrusion temperature (100°C) and screw speed (230rpm), it was possible to obtain puffed snack products with desirable characteristics.

Application of extruded broken bean flour for formulation of gluten-free cake blends

The aim of this study was to determine the physical and microbiological characteristics of extruded broken beans flour, in addition to developing mixtures for gluten-free cake with these flours, evaluating their technological and sensory quality. Gluten-free formulations were prepared with 45%, 60% and 75% of extruded broken beans. All analyzes of the flours and mixtures for cakes were performed according to standard techniques found in the literature. Sensory analyzes of cakes applied the 9-point structured hedonic scale. Results were submitted to variance analysis and comparison of means test (Tukey, p<0.05). The use of extruded broken beans improved the water absorbed and water solubility index of the mixtures for gluten-free cake, and for the lower viscosity and retrogradation when compared to the standard formulation. All cakes were accepted (rate ≥ 7) for all the analyzed attributes. From the technological and sensory standpoints, the development of gluten-free cake mixtures is feasible with up to 75% of extruded broken beans.

Construction of I-Deletion-Correcting Ternary Codes

Finding large deletion correcting codes is an important issue in coding theory. Many researchers have studied this topic over the years. Varshamov and Tenegolts constructed the Varshamov-Tenengolts codes (VT codes) and Levenshtein showed the Varshamov-Tenengolts codes are perfect binary one-deletion correcting codes in 1992. Tenegolts constructed T codes to handle the non-binary cases. However the T codes are neither optimal nor perfect, which means some progress can be established. Latterly, Bours showed that perfect deletion-correcting codes have a close relationship with design theory. By this approach, Wang and Yin constructed perfect 5-deletion correcting codes of length 7 for large alphabet size. For our research, we focus on how to extend or combinatorially construct large codes with longer length, few deletions and small but non-binary alphabet especially ternary. After a brief study, we discovered some properties of T codes and produced some large codes by 3 different ways of extending some existing good codes.

The Role of Specific Amino Acids in the Formation of Ternary Complexes in Nitrogenase Regulation in the Photosynthetic Bacterium Rhodobacter capsulatus

L'azote est l'un des éléments les plus essentiels dans le monde pour les êtres vivants, car il est essentiel pour la production des éléments de base de la cellule, les acides aminés, les acides nucléiques et les autres constituants cellulaires. L’atmosphère est composé de 78% d'azote gazeux, une source d'azote inutilisable par la plupart des organismes à l'exception de ceux qui possèdent l’enzyme nitrogénase, tels que les bactéries diazotrophique. Ces micro-organismes sont capables de convertir l'azote atmosphérique en ammoniac (NH3), qui est l'une des sources d'azote les plus préférables. Cette réaction exigeant l’ATP, appelée fixation de l'azote, est catalysée par une enzyme, nitrogénase, qui est l'enzyme la plus importante dans le cycle de l'azote. Certaines protéines sont des régulateurs potentiels de la synthèse de la nitrogénase et de son activité; AmtB, DraT, DraG, les protéines PII, etc.. Dans cette thèse, j'ai effectué diverses expériences afin de mieux comprendre leurs rôles détailés dans Rhodobacter capsulatus. La protéine membranaire AmtB, très répandue chez les archaea, les bactéries et les eucaryotes, est un membre de la famille MEP / Amt / Rh. Les protéines AmtB sont des transporteurs d'ammonium, importateurs d'ammonium externe, et ont également été suggéré d’agir comme des senseurs d'ammonium. Il a été montré que l’AmtB de Rhodobacter capsulatus fonctionne comme un capteur pour détecter la présence d'ammonium externe pour réguler la nitrogénase. La nitrogénase est constituée de deux métalloprotéines nommées MoFe-protéine et Fe-protéine. L'addition d'ammoniaque à une culture R. capsulatus conduit à une série de réactions qui mènent à la désactivation de la nitrogénase, appelé "nitrogénase switch-off". Une réaction critique dans ce processus est l’ajout d’un groupe ADP-ribose à la Fe-protéine par DraT. L'entrée de l'ammoniac dans la cellule à travers le pore AmtB est contrôlée par la séquestration de GlnK. GlnK est une protéine PII et les protéines PII sont des protéines centrales dans la régulation du métabolisme de l'azote. Non seulement la séquestration de GlnK par AmtB est importante dans la régulation nitrogénase, mais la liaison de l'ammonium par AmtB ou de son transport partiel est également nécessaire. Les complexes AmtB-GlnK sont supposés de lier DraG, l’enzyme responsable pour enlever l'ADP-ribose ajouté à la nitrogénase par DraT, ainsi formant un complexe ternaire. Dans cette thèse certains détails du mécanisme de transduction du signal et de transport d'ammonium ont été examinés par la génération et la caractérisation d’un mutant dirigé, RCZC, (D335A). La capacité de ce mutant, ainsi que des mutants construits précédemment, RCIA1 (D338A), RCIA2 (G344C), RCIA3 (H193E) et RCIA4 (W237A), d’effectuer le « switch-off » de la nitrogénase a été mesurée par chromatographie en phase gazeuse. Les résultats ont révélé que tous les résidus d'acides aminés ci-dessus ont un rôle essentiel dans la régulation de la nitrogénase. L’immunobuvardage a également été effectués afin de vérifier la présence de la Fe-protéine l'ADP-ribosylée. D335, D388 et W237 semblent être cruciales pour l’ADP-ribosylation, puisque les mutants RCZC, RCIA1 et RCIA4 n'a pas montré de l’ADP-ribosylation de la Fe-protéine. En outre, même si une légère ADP-ribosylation a été observée pour RCIA2 (G344C), nous le considérons comme un résidu d'acide aminé important dans la régulation de la nitrogénase. D’un autre coté, le mutant RCIA3 (H193E) a montré une ADP-ribosylation de la Fe-protéine après un choc d'ammonium, par conséquent, il ne semble pas jouer un rôle important dans l’ADP-ribosylation. Par ailleurs R. capsulatus possède une deuxième Amt appelé AmtY, qui, contrairement à AmtB, ne semble pas avoir des rôles spécifiques. Afin de découvrir ses fonctionnalités, AmtY a été surexprimée dans une souche d’E. coli manquant l’AmtB (GT1001 pRSG1) (réalisée précédemment par d'autres membres du laboratoire) et la formation des complexes AmtY-GlnK en réponse à l'addition d’ammoniac a été examinée. Il a été montré que même si AmtY est en mesure de transporter l'ammoniac lorsqu'il est exprimé dans E. coli, elle ne peut pass’ associer à GlnK en réponse à NH4 +.

Studies on Xanthate/Dithiocarbamate Accelerator Combination in NR/BR Blends

Zinc butyl xanthate [Zn(bxt)2] was prepared in the laboratory . The effect of this xanthate with zinc diethyl dithiocarbamate (ZDC) on the vulcanization of natural rubber ( NR), polybutadiene rubber (BR), and NR/BR blend has been studied at different temperatures. The amounts of Zn (bxt)2 and ZDC in the compounds were optimized by varying the amount of ZDC from 0 . 75 to 1.5 phr and Zn (bxt)2 from 0 . 75 to 1 .5 phr. The cure characteristics were also studied . HAF filled NR, BR, and NR / BR blend compounds were cured at different temperatures from 60 to 150 C. The sheets were molded and properties such as tensile strength, tear strength, crosslink density and elongation at break, compression set, abrasion resistance, etc. were evaluated. The results show that the mechanical properties of 80NR/20BR blends are closer to that of NR vulcanizates, properties of 60NR/40BR blends are closer to BR vulcanizates, while the 70NR/30BR blends show an intermediate property.

EPDM/CIIR Blends : Effect of EPDM Grade on Mechanical Properties

Blends of chlorobutyl rubber (CIIR) with two grades of ethylene-propylene diene monomer rubber (EPDM) were prepared and the effect of blend ratio on the cure characteristics, hot air ageing resistance, steam ageing resistance, and mechanical properties were evaluated. The blend of CIIR with EPDM grade 301 T showed additive behavior and the blend with the other grade of EPDM (NDR 4640) showed synergistic behavior.

Chemical Modification of Blends of Poly (Vinyl Chloride) With Linear Low Density Polyethylene

The effects of modifying blends of poly(vinyl chloride) (PVC) with linear low density polyethylene (LLDPE) by means of acrylic acid, maleic anhydride, phenolic resins and p-phenylene diamine were investigated. Modification by acrylic acid and maleic anhydride in the presence of dicumyl peroxide was found to be the most useful procedure for improving the mechanical behaviour and adhesion properties of the blend. The improvement was found to be due mainly to the grafting of the carboxylic acid to the polymer chains; grafting was found to be more effective in LLDPE/PVC blends than in pure LLDPE.

Studies on NBR/PVC Blends

Studies conducted on butadiene-acrylonitrile copolymer (NBR)/poly(vinyl chloride) (PVC) blends at different temperatures indicate that an optimum temperature exists for the formation of a particular blend. The mechanical properties of the blends confirm this observation. PVC stabilizer based on, magnesium oxide , zinc oxide, and stearic acid was found to be very useful in NBR/PVC blends.