Biodegradation of poly(L-lactide-co-glycolide) tube stents in bile

The objective of this study was to evaluate degradation behavior and the feasibility of biodegradable polymeric stents in common bile duct (CBD) repair and reconstruction. Various molar ratios of lactide (LA) and glycolide (GA) in poly(L-lactide-co-glycolide) (PLGA) were synthesized and processed into a circular tubing of similar to 10.0 mm outer diameter and a wall thickness of about 2.0 mm.

Stabilization of poly(lactic acid) by polycarbodiimide

Polycarbodiimide (CDI) was used to improve the thermal stability of poly(L-lactic acid) (PLA) during processing. The properties of PLA containing various amounts of CDI were characterized by GPC, DSC, rheology, and tensile tests. The results showed that an addition of CDI in an amount of 0.1-0.7 wt% with respect to PLA led to stabilization of PLA at even 210 degrees C for up to 30 min, as evidenced by much smaller changes in molecular weight. melt viscosity, and tensile strength and elongation compared to the blank PLA samples. In order to examine the possible stabilization mechanism, CDI was reacted with water, acetic acid, L-lactic acid, ethanol and low molecular weight PLA. The molecular structures of the reaction products were measured with FTIR.

Electron-beam irradiation on poly(propylene carbonate) in the presence of polyfunctional monomers

Poly(propylene carbonate) (PPC) showed predominantly degradation under electron-beam irradiation, accompanied by deterioration of its mechanical performance due to sharp decrease of the molecular weight. Crosslinked PPC was prepared by addition of polyfunctional monomer (PFM) to enhance the mechanical performance of PPC. When 8 wt% of PFM like triallyl isocyanurate (TAIL) was added, crosslinked PPC with a gel fraction of 60.7% was prepared at 50 kGy irradiation dose, which showed a tensile strength at 20 degrees C of 45.5 MPa, whereas it was only 38.5 MPa for pure PPC. The onset degradation temperature (T-i) and glass transition temperature (T-g) of this crosslinked PPC was 246 degrees C and 45 degrees C, respectively, a significant increase related to pure PPC of 211 degrees C and 36 C. Therefore, thermal and mechanical performances of PPC could be improved via electron-beam irradiation in the presence of suitable PFM.

gamma-Radiation damage to nylon 1010 containing neodymium oxide

A comparison of radiation damage to nylon 1010 (denoted nylon-a) and nylon 1010 containing neodymium oxide (Nd2O3) (denoted nylon-b) was made by DSC, WAXD, ESR and the determination of gel fractions. The results show that radiation damage to nylon-b is delayed, and radiation damage to nylon-a is more severe than that to nylon-b, due to the protection of the fold surface of the lamellae. Furthermore, the fact that the damage begins with the fold surface of the lamellae is confirmed. (C) 1996 Elsevier Science Limited

Effect of irradiation on pyrolysis of polypropylene in the presence of zeolites

For recycling of waste polymers, the degradation behavior of PP was studied with a combination of radiolysis and thermolysis methods. The results revealed that thermal degradation temperature of PP was significantly reduced when PP was irradiated in the presence of a zeolite. The irradiation-induced temperature reduction depended on the zeolite structure and composition, as well as on the morphology of the mixture. Identification of pyrolysis products indicated that, in the absence of zeolite, irradiation resulted only in a change of the product distribution but no formation of new compounds. In the presence of zeolite, however, a series of oxidized products were formed. In addition, the pyrolysis could be performed at a much lower temperature. (C) 1996 Elsevier Science Limited

Effects of zeolites on the pyrolysis of polypropylene

With the intention of understanding chemical recycling of waste polymers, various kinds of zeolites were used as catalysts in the pyrolysis of polypropylene (PP). The effects of zeolites on the degradation temperature and pyrolyzed products of PP were studied. It was found that the degradation temperature of PP strongly depended on the type of zeolite used and the amount added. One type of HY zeolite (320HOA) was shown to be a very effective catalyst. Pyrolysis products, which were identified by using a coupled gas-chromatograph-mass-spectrometer, were also affected by the addition of zeolites. Some zeolites did not change the structure of the products but narrowed the product distribution to a smaller molecule region, while the HY zeolite led to hydrocarbons concentrated at those containing 4-9 carbons. Furthermore, some new compounds with cyclic structures were found in the presence of the HY zeolite. (C) 1996 Elsevier Science Limited

Chemiluminescence studies of radiation induced oxidation of various polyethylenes

The chemiluminescence (CL) emission from three kinds of polyethylene, HDPE, LLDPE and LDPE, which had been exposed to 80 kGy dose from Co-60 in both air and nitrogen, has been examined. CL measurement was done under both nitrogen and oxygen atmosphere. The results show that the CL emission from irradiated samples does not result from irradiation itself, but from the oxidation reactions occurring during and after irradiation. Addition of 1 phr of an antioxidant, Irganox 1010, can effectively inhibit the radiation induced oxidation in LLDPE and LDPE. In the case of HDPE, however, it was found that pure HDPE has the best resistance to radiation-induced oxidation of the polymers examined in this work. However, incorporation of Irganox 1010 was found to have not only a stabilizing effect against radiation induced oxidation, but also to promote the oxidation in some cases.

THE INFLUENCE OF GAMMA-RADIATION ON POLYAMIDE-1010 AGGREGATE STRUCTURES

The influence of gamma-radiation on polyamide 1010 aggregate structures and crystal damage were examined by using wide angle X-ray diffraction (WAXD) and small angle X-ray scattering (SAXS) techniques. The results revealed that some structural parameters of the aggregated state, the density differences and the degree of crystallinity W-c,W-x, essentially decreased with increasing radiation dose, but the specific surface O-s increased. Crosslinking and scission of irradiated polyamide 1010 samples occurred mainly in amorphous and interphase regions, and crystal damage and amorphization induced by gamma-radiation spread from the interphase and extended into the crystal phase with increasing radiation dose. This result also indicated that the (010) reflection with the hydrogen bond was more susceptible to the action of radiation.

ESTIMATION OF THE RADIATION-INDUCED DAMAGE IN PTFE BY DEPRESSION OF THE MELTING AND CRYSTALLIZATION TEMPERATURES

The radiation induced depression of the melting and crystallization temperatures of PTFE irradiated at various temperatures followed by heat treatment at 380-degrees-C, and their relationship to structural changes, were investigated. The G(-units) values obtained in this work are different from those of samples which have not undergone heat treatment and seem to be more closely associated with radiation induced branched structures.

RADIATION CROSS-LINKING OF CHLORINATED POLYISOBUTYLENE

The effects of radiation on chlorinated polyisobutylene were studied. It was found that polyisobutylene, which is generally considered to be a typical radiation-degradative polymer, could be crosslinked by gamma-ray irradiation after chlorine had been introduced into its macromolecules. Carbon-chlorine bonds act both as radiation-sensitive groups and reaction species in the radiation process of chlorinated polyisobutylene.

SOME CHEMICAL-CHANGES IN CHITOSAN INDUCED BY GAMMA-RAY IRRADIATION

Chitosan was subjected to gamma-ray irradiation in air. It was found that the -NH2 group is more sensitive to irradiation than the -NHCOCH3 group, and moreover, the hydroxyl group increases with increasing radiation dose while the C-O-C group decreases, but no evidence for carbonyl formation was observed.

RADIATION-INDUCED CRYSTAL DEFECTS IN PTFE

Changes induced in the crystal structure of PTFE by irradiation at different temperatures have been investigated. In the dose and temperature range examined, the density of PTFE was observed to increase continuously with increasing dose due to the radiation-induced increase in crystallinity, while after post-irradiation annealing at 380-degrees-C, the density was observed to increase for samples irradiated at 20-degrees-C, and to begin to decrease after a certain dose for samples irradiated at 150 and 200-degrees-C. On the basis of the observation of radiation-induced separation of the melting peak of PTFE and its stability relative to the change in the rate of heating, the observed decrease in density was explained as being due to the radiation-induced crosslinking and/or branching inhibiting the process of crystallization and existing in the crystalline region as defects.

THE RADIATION STABILITY OF PERFLUOROALKOXY RESIN

By examining the changes in melting temperature, heat of fusion, tensile strength and ultimate elongation at 150-degrees-C, and weight loss, radiation effects on perfluoroalkoxy resins (PFA) were investigated. The results show that at the temperatures used here the predominant effect caused by radiation on PFA is degradation of the molecular weight. The radiation stability is much better than that of polytetrafluoroethylene, however.