A nano-patterned photonic crystal laser with a dye-doped liquid crystal

Covering a nano-patterned titanium dioxide photonic crystal (PC) within a well-oriented film of dye-doped liquid crystal (LC), a distributed feedback laser is constructed whereby the emission characteristics can be manipulated in-situ using an electric field. This hybrid organic-inorganic structure permits simultaneous selectivity of both the beam pattern and laser wavelength by electrical addressing of the LC director. In addition, laser emission is obtained both in the plane and normal to the PC. Along with experimental data, a theoretical model is presented that is based upon an approximate calculation of the band structure of this birefringent, tuneable laser device. © 2013 AIP Publishing LLC.

Parabolic tapered photonic crystal cavity in silicon

We demonstrate the design, fabrication, transmission and nearfield characterization of a novel parabolic tapered 1D photonic crystal cavity in silicon. The design allows repeatable device fabrication, high quality factor and small modal volume. © 2012 OSA.

Parabolic tapered photonic crystal cavity in silicon

We demonstrate the design, fabrication, transmission and nearfield characterization of a novel parabolic tapered 1D photonic crystal cavity in silicon. The design allows repeatable device fabrication, high quality factor and small modal volume. © OSA 2012.

Parabolic tapered photonic crystal cavity in silicon

We demonstrate the design, fabrication, transmission and nearfield characterization of a novel parabolic tapered 1D photonic crystal cavity in silicon. The design allows repeatable device fabrication, high quality factor and small modal volume. © 2012 OSA.

Parabolic tapered photonic crystal cavity in silicon

We demonstrate the design, fabrication, transmission spectrum measurement, and near-field characterization of a parabolic tapered one-dimensional photonic crystal cavity in silicon. The results shows a relatively high quality factor (∼43 000), together with a small modal volume of ∼ 1. 1 (λ/n) 3. Moreover, the design allows repeatable device fabrication, as evident by the similar characteristics obtained for several tens of devices that were fabricated and tested. These demonstrated 1D PhC cavities may be used as a building block in integrated photonic circuits for optical on-chip interconnects and sensing applications. © 2012 American Institute of Physics.

Parabolic tapered photonic crystal cavity in silicon

We demonstrate the design, fabrication, transmission and nearfield characterization of a novel parabolic tapered 1D photonic crystal cavity in silicon. The design allows repeatable device fabrication, high quality factor and small modal volume. © OSA 2012.

Computational modelling and characterisation of nanoparticle-based tuneable photonic crystal sensors

Photonic crystals are materials that are used to control or manipulate the propagation of light through a medium for a desired application. Common fabrication methods to prepare photonic crystals are both costly and intricate. However, through a cost-effective laser-induced photochemical patterning, one-dimensional responsive and tuneable photonic crystals can easily be fabricated. These structures act as optical transducers and respond to external stimuli. These photonic crystals are generally made of a responsive hydrogel that can host metallic nanoparticles in the form of arrays. The hydrogel-based photonic crystal has the capability to alter its periodicity in situ but also recover its initial geometrical dimensions, thereby rendering it fully reversible and reusable. Such responsive photonic crystals have applications in various responsive and tuneable optical devices. In this study, we fabricated a pH-sensitive photonic crystal sensor through photochemical patterning and demonstrated computational simulations of the sensor through a finite element modelling technique in order to analyse its optical properties on varying the pattern and characteristics of the nanoparticle arrays within the responsive hydrogel matrix. Both simulations and experimental results show the wavelength tuneability of the sensor with good agreement. Various factors, including nanoparticle size and distribution within the hydrogel-based responsive matrices that directly affect the performance of the sensors, are also studied computationally. © 2014 The Royal Society of Chemistry.

A Single-Fundamental-Mode Photonic Crystal Vertical Cavity Surface Emitting Laser

Single-fundamental-mode photonic crystal (PhC) vertical cavity surface emitting lasers (VCSEL) are produced and their single-fundamental-mode performances are investigated and demonstrated. A two-dimensional PhC with single-point-defect structure is fabricated using UV photolithography and inductive coupled plasma reactive ion etching on the surface of the VCSEL's top distributed Bragg-reflector. The PhC VCSEL maintains single-fundamental-mode operating with output power 1.7 mW and threshold current 2.5 mA. The full width half maximum of the lasing spectrum is less than 0.1 nm, the far field divergence angle is less than 10 degrees and the side mode suppression ratio is over 35 dB. The device characteristics are analyzed based on the effective index model of the photonic crystal fiber. The experimental results agree well with the theoretical expectation.

Ultracompact triplexer by coupling and decoupling of multiple photonic crystal waveguides

We investigate numerically the self-imaging effect in a system of multiple coupled photonic crystal waveguides (M-CPCWs) with asymmetric coupling. Then two couplers of 2-CPCWs and 3-CPCWs are cascaded to form an ultracompact triplexer by employing coupling and decoupling of M-CPCWs. The wavelength of 1310 nm propagates along the input direction because the M-CPCWs are decoupled at the same decoupling frequency. The other two wavelengths (1490 and 1550 nm) are separated by combining multimode interference and the dual mode coupling effect. Only by introducing a single defect near the crossing point between two output photonic crystal waveguides (PCWs) are the high extinction ratios for the three wavelengths achieved simultaneously.

Degenerate four-wave mixing based all-optical wavelength conversion in a semiconductor optical amplifier and highly-nonlinear photonic crystal fiber parametric loop mirror

The idler is separated from the co-propagating pump in a degenerate four-wave mixing (DFWM) with a symmetrical parametric loop mirror (PALM), which is composed of two identical SOAs and a 70 m highly-nonlinear photonic crystal fiber (HN-PCF). The signal and pump are coupled into the symmetrical PALM from different ports, respectively. After the DFWM based wavelength conversion (WC) in the clockwise and anticlockwise, the idler exits from the signal port, while the pump outputs from its input port. Therefore, the pump is effectively suppressed in the idler channel without a high-speed tunable filter. Contrast to a traditional PALM, the DFWM based conversion efficiency is increased greatly, and the functions of the amplification and the WC are integrated in the smart SOA and HN-PCF PALM. (C) 2008 Elsevier B.V. All rights reserved.

The impact of imperfect symmetry on band edge modes of a two-dimensional photonic crystal with square lattice

A theoretical analysis has been performed by means of the plane-wave expansion method to examine the dispersion properties of photons at high symmetry points of an InP based two-dimensional photonic crystal with square lattice. The Q factors are compared qualitatively. The mechanism of surface-emitting is due to the photon manipulation by periodic dielectric materials in terms of Bragg diffraction. A surface-emitting photonic crystal resonator is designed based on the phenomenon of slow light. Photonic crystal slabs with different unit cells are utilized in the simulation. The results indicate that the change of the air holes can affect the polarization property of the modes. So we can find a way to improve the polarization by reducing the symmetry of the structure.

Design of a compact polarization beam splitter based on a deformed photonic crystal directional coupler

In this paper a compact polarization beam splitter based on a deformed photonic crystal directional coupler is designed and simulated. The transverse-electric (TE) guided mode and transverse-magnetic (TM) guided mode are split due to different guiding mechanisms. The effect of the shape deformation of the air holes on the coupler is studied. It discovered that the coupling strength of the coupled waveguides is strongly enhanced by introducing elliptical airholes, which reduce the device length to less than 18.5 mu m. A finite-difference time-domain simulation is performed to evaluate the performance of the device, and the extinction ratios for both TE and TM polarized light are higher than 20 dB.

Application of fast Pade approximation in simulating photonic crystal nanocavities by FDTD technology

The exact calculation of mode quality factor Q is a key problem in the design of high-Q photonic crystal nanocavity. On the basis of further investigation on conventional Pade approximation, FDM and DFT, Pade approximation with Baker's algorithm is enhanced through introducing multiple frequency search and parabola interpolation. Though Pade approximation is a nonlinear signal processing method and only short time sequence is needed, we find the different length of sequence requirements for 2D and 3D FDTD, which is very important to obtain convergent and accurate results. By using the modified Pade approximation method and 3D FDTD, the 2D slab photonic crystal nanocavity is analyzed and high-Q multimode can be solved quickly instead of large range high-resolution scanning. Monitor position has also been investigated. These results are very helpful to the design of photonic crystal nanocavity devices. (C) 2008 Elsevier B.V. All rights reserved.

Dispersion-compensating photonic crystal fibers with special characteristics

Based on the modified dual core structure, three kinds of special photonic crystal fibers are presented, which are extremely large negative dispersion, super-broad bond, and large area made field dispersion-compensating photonic crystal fibers (DCPCF). For extremely large negative dispersion DCPCF, the peak of negative dispersion reaches -5.9 x 10(4) ps/(mn km). Super-broad bond DCPCF has broadband large negative dispersion and the dispersion value varies linearly from -380 ps/(nm km) to -420 ps/(nm km) in the C band. The designed large area made field DCPCF has a peak dispersion of -1203 ps/(nm km) with the inner core mode area of 47 mu m(2) and outer core mode area of 835 mu m(2). Furthermore, for the large area mode field DCPCF, the experimental result is also obtained. (C) 2008 Wiley Periodicals, Inc.

Room-temperature photonic crystal laser in H3 cavity on InGaAsP/InP slab

We fabricate and investigate two-dimensional photonic crystal H3 microcavities in an InGaAsP slab. The lasing action at room temperature is observed. The lasering threshold is 7mW under the pulsed pump of 0.75% duty cycle. The Q factor and the lasing mode characteristics are simulated by three-dimensional finite difference time domain method. The simulation result matches well with the experiment.