Experimental investigation of antenna selection and transmit beamforming for capacity enhancement in 3×3 MIMO-enabled radio-over-fiber DAS

This paper examines the impact of two simple precoding schemes on the capacity of 3 × 3 MIMO-enabled radio-over-fiber (RoF) distributed antenna systems (DAS) with excess transmit antennas. Specifically, phase-shift-only transmit beamforming and antenna selection are compared. It is found that for two typical indoor propagation scenarios, both strategies offer double the capacity gain that non-precoding MIMO DAS offers over traditional MIMO collocated antenna systems (CAS), with capacity improvements of 3.2-4.2 bit/s/Hz. Further, antenna selection shows similar performance to phase-only beamforming, differing by <0.5% and offering median capacities of 94 bit/s/Hz and 82 bit/s/Hz in the two propagation scenarios respectively. Because optical DASs enable precise, centralized control of remote antennas, they are well suited for implementing these beamforming schemes. Antenna selection, in particular, is a simple and effective means of increasing MIMO DAS capacity. © 2013 IEEE.

Interaction of additive and quantization noises in digital PLLs

Phase-locked loops (PLLs) are a crucial component in modern communications systems. Comprising of a phase-detector, linear filter, and controllable oscillator, they are widely used in radio receivers to retrieve the information content from remote signals. As such, they are capable of signal demodulation, phase and carrier recovery, frequency synthesis, and clock synchronization. Continuous-time PLLs are a mature area of study, and have been covered in the literature since the early classical work by Viterbi [1] in the 1950s. With the rise of computing in recent decades, discrete-time digital PLLs (DPLLs) are a more recent discipline; most of the literature published dates from the 1990s onwards. Gardner [2] is a pioneer in this area. It is our aim in this work to address the difficulties encountered by Gardner [3] in his investigation of the DPLL output phase-jitter where additive noise to the input signal is combined with frequency quantization in the local oscillator. The model we use in our novel analysis of the system is also applicable to another of the cases looked at by Gardner, that is the DPLL with a delay element integrated in the loop. This gives us the opportunity to look at this system in more detail, our analysis providing some unique insights into the variance `dip' seen by Gardner in [3]. We initially provide background on the probability theory and stochastic processes. These branches of mathematics are the basis for the study of noisy analogue and digital PLLs. We give an overview of the classical analogue PLL theory as well as the background on both the digital PLL and circle map, referencing the model proposed by Teplinsky et al. [4, 5]. For our novel work, the case of the combined frequency quantization and noisy input from [3] is investigated first numerically, and then analytically as a Markov chain via its Chapman-Kolmogorov equation. The resulting delay equation for the steady-state jitter distribution is treated using two separate asymptotic analyses to obtain approximate solutions. It is shown how the variance obtained in each case matches well to the numerical results. Other properties of the output jitter, such as the mean, are also investigated. In this way, we arrive at a more complete understanding of the interaction between quantization and input noise in the first order DPLL than is possible using simulation alone. We also do an asymptotic analysis of a particular case of the noisy first-order DPLL with delay, previously investigated by Gardner [3]. We show a unique feature of the simulation results, namely the variance `dip' seen for certain levels of input noise, is explained by this analysis. Finally, we look at the second-order DPLL with additive noise, using numerical simulations to see the effects of low levels of noise on the limit cycles. We show how these effects are similar to those seen in the noise-free loop with non-zero initial conditions.

Complex molecule formation in grain mantles

Context. Complex molecules such as ethanol and dimethyl ether have been observed in a number of hot molecular cores and hot corinos. Attempts to model the molecular formation process using gas phase only models have so far been unsuccessful. Aims. To demonstrate that grain surface processing is a viable mechanism for complex molecule formation in these environments. Methods. A variable environment parameter computer model has been constructed which includes both gas and surface chemistry. This is used to investigate a variety of cloud collapse scenarios. Results. Comparison between model results and observation shows that by combining grain surface processing with gas phase chemistry complex molecules can be produced in observed abundances in a number of core and corino scenarios. Differences in abundances are due to the initial atomic and molecular composition of the core/corino and varying collapse timescales. Conclusions. Grain surface processing, combined with variation of physical conditions, can be regarded as a viable method for the formation of complex molecules in the environment found in the vicinity of a hot core/corino and produce abundances comparable to those observed.

Pilot Tone Actuated Antenna Array Pattern Reconfiguration

A new strategy for remote reconfiguration of an antenna array far field radiation pattern is described. The scheme uses a pilot tone co-transmitted with a carrier signal from a location distant from that of a receive antenna array whose far field pattern is to be reconfigured. By mixing the co-transmitted signals locally at each antenna element in the array an IF signal is formed which defines an equivalent array spacing that can be made variable by tuning the frequency of the pilot tone with respect to the RF carrier. This makes the antenna array factor hence far field spatial characteristic reconfigurable on receive. For a 10 x 1 microstrip patch element array we show that the receive pattern can be made to vary from 35 to 10 degrees half power beam width as the difference frequency between the pilot and the carrier at 2.45 GHz varies between 10 MHz and 500 MHz carrier.

Analogies to semantic and syntactic mental labour in the Feist decision

The Supreme Court of the United States in Feist v. Rural (Feist, 1991) specified that compilations or databases, and other works, must have a minimal degree of creativity to be copyrightable. The significance and global diffusion of the decision is only matched by the difficulties it has posed for interpretation. The judgment does not specify what is to be understood by creativity, although it does give a full account of the negative of creativity, as ‘so mechanical or routine as to require no creativity whatsoever’ (Feist, 1991, p.362). The negative of creativity as highly mechanical has particularly diffused globally.

A recent interpretation has correlated ‘so mechanical’ (Feist, 1991) with an automatic mechanical procedure or computational process, using a rigorous exegesis fully to correlate the two uses of mechanical. The negative of creativity is then understood as an automatic computation and as a highly routine process. Creativity is itself is conversely understood as non-computational activity, above a certain level of routinicity (Warner, 2013).

The distinction between the negative of creativity and creativity is strongly analogous to an independently developed distinction between forms of mental labour, between semantic and syntactic labour. Semantic labour is understood as human labour motivated by considerations of meaning and syntactic labour as concerned solely with patterns. Semantic labour is distinctively human while syntactic labour can be directly humanly conducted or delegated to machine, as an automatic computational process (Warner, 2005; 2010, pp.33-41).

The value of the analogy is to greatly increase the intersubjective scope of the distinction between semantic and syntactic mental labour. The global diffusion of the standard for extreme absence of copyrightability embodied in the judgment also indicates the possibility that the distinction fully captures the current transformation in the distribution of mental labour, where syntactic tasks which were previously humanly performed are now increasingly conducted by machine.

The paper has substantive and methodological relevance to the conference themes. Substantively, it is concerned with human creativity, with rationality as not reducible to computation, and has relevance to the language myth, through its indirect endorsement of a non-computable or not mechanical semantics. These themes are supported by the underlying idea of technology as a human construction. Methodologically, it is rooted in the humanities and conducts critical thinking through exegesis and empirically tested theoretical development

References

Feist. (1991). Feist Publications, Inc. v. Rural Tel. Service Co., Inc. 499 U.S. 340.

Warner, J. (2005). Labor in information systems. Annual Review of Information Science and Technology. 39, 2005, pp.551-573.

Warner, J. (2010). Human Information Retrieval (History and Foundations of Information Science Series). Cambridge, MA: MIT Press.

Warner, J. (2013). Creativity for Feist. Journal of the American Society for Information Science and Technology. 64, 6, 2013, pp.1173-1192.

IB-DFE receiver techniques for CP-assisted block transmission within DS-CDMA and MC-CDMA systems

MC-CDMA (MultiCarrier Code Division Multiple Access), currently regarded as a promissing multiple access scheme for broadband communications, is known to combine the advantages of an OFDM-based (Orthogonal Frequency Division Multiplexing), CP-assisted (Cyclic Prefix) block transmission with those of CDMA systems. Recently, it was recognised that DS-CDMA (Direct Sequence) implementations can also take advantage of the beneficts of the CP-assisted block transmission approach, therefore enabling an efficient use of FFT-based (Fast Fourier Transform), chip level FDE (Frequency- Domain Equalisation) techniques. In this paper we consider the use of IB-DFE (Iterative Block Decision Feedback Equalisation) FDE techniques within both CP-assisted MC-CDMA systems with frequency-domain spreading and DS-CDMA systems. Our simulation results show that an IB-DFE receiver with moderate complexity is suitable in both cases, with excellent performances that can be close to the single-code matched filter bound (especially for the CP-assisted DSCDMA alternative), even with full code usage.

SIC and PIC multiuser detection for prefix-assisted DS-CDMA systems

In this paper we present iterative frequency-domain multiuser detection (MUD) receivers for the uplink transmission of direct sequence code division multiple access systems (DS-CDMA) that combine iterative block decision feedback equalization (IB-DFE) principles with interference cancelation techniques. Both successive interference cancelation (SIC) and parallel interference cancelation (PIC) structures are considered. Our performance results show that the proposed receiver structures have excellent bit error rate (BER) performances, that can be close to the single-user matched filter bound (MFB), even for fully loaded systems and severely time-dispersive channels1.

Multiuser Detection for the Uplink of Prefix-Assisted DS-CDMA Systems Employing Multiple Transmit and Receive Antennas

In this paper we consider the uplink transmission within a DS-CDMA system employing CP-assisted (Cylic Prefix) block transmission techniques combined with spatial multiplexing techniques that require multiple antennas at both the transmitter and the receiver. We present an efficient frequency-domain receiver structure with iterative MUD (MultiUser Detection). The performance of the proposed receiver can be close to the single user matched filter bound, even for fully loaded systems and/or severely time-dispersive channels.

Simulação de um processo de pirólise rápida de biomassa

Mestrado em Engenharia Química - Ramo Optimização Energética na Indústria Química

Rôle des informations proprioceptives dans l’équilibre à la marche chez les personnes en santé et hémiparétiques

L'utilisation des informations proprioceptives pour le contrôle de l’équilibre à la marche est encore mal comprise chez les sujets en santé ou hémiparétiques suite à un accident vasculaire cérébral. Le but de cette étude était d’évaluer le rôle des informations proprioceptives dans le maintien de l'équilibre à la marche chez les patients en santé et hémiparétiques. Une analyse de mouvement en trois dimensions a été faite chez treize participants en santé et six hémiparétiques qui marchaient sur un tapis roulant instrumenté pour déterminer leur difficulté à maintenir l’équilibre postural et dynamique, évaluée respectivement par les forces stabilisante et déstabilisante. Des vibrations étaient appliquées en continu ou pendant la phase d’appui sur les muscles postérieurs du cou et sur le triceps sural du côté non-dominant/parétique. La vibration continue ou à l’appui du triceps sural a diminué, chez les sujets en santé, la difficulté à maintenir l’équilibre dynamique et postural (p< 0,01), avec une position du corps plus en arrière, sans changement des paramètres temporels de marche. L'équilibre et les paramètres temporels de la marche n'étaient pas modifiés significativement par la vibration à la nuque (p>.17). Aucun effet des vibrations n'a été mesuré chez les patients hémiparétiques (p> 0,45). Les informations proprioceptives sont donc bien utilisées lors de la marche, mais leur rôle dépendrait des conditions de marche et des afférences visuelles disponibles. Un changement dans les capacités d’intégration expliquerait l'absence d'effet des vibrations chez les patients hémiparétiques. D’autres études sont nécessaires pour comprendre l’intégration des informations proprioceptives et visuelles dans le contrôle de l’équilibre à la marche.

Coupling cancellation based multiuser detector for asynchronous DS/CDMA

A three-shot multiuser detector is proposed for the reverse link of asynchronous DS/CDMA systems. By taking advantage of the preceding (already reconstructed) bit and the matched filter output for the following two bits, the coupling between temporally adjacent bits (TABs, which always exists for asynchronous systems) is cancelled in a three step fashion. The obtained detector has several useful advantages over existing schemes.

A linear CDMA detector based on minimum variance distortionless response (MVDR)

A bit-level processing (BLP) based linear CDMA detector is derived following the principle of minimum variance distortionless response (MVDR). The combining taps for the MVDR detector are determined from (1) the covariance matrix of the matched filter output, and (2) the corresponding row (or column) of the user correlation matrix. Due to the interference suppression capability of MVDR and the fact that no inversion of the user correlation matrix is involved, the influence of the synchronisation errors is greatly reduced. The detector performance is demonstrated via computer simulations (both synchronisation errors and intercell interference are considered).

A three-shot improvement scheme for hard-decision based linear decorrelating detector in DS/CDMA

This paper proposes a three-shot improvement scheme for the hard-decision based method (HDM), an implementation solution for linear decorrelating detector (LDD) in asynchronous DS/CDMA systems. By taking advantage of the preceding (already reconstructed) bit and the matched filter output for the following two bits, the coupling between temporally adjacent bits (TABs), which always exists for asynchronous systems, is greatly suppressed and the performance of the original HDM is substantially improved. This new scheme requires no signaling overhead yet offers nearly the same performance as those more complicated methods. Also, it can easily accommodate the change in the number of active users in the channel, as no symbol/bit grouping is involved. Finally, the influence of synchronisation errors is investigated.

Constraints on wave drag parameterization schemes for simulating the quasi-biennial oscillation. Part I: gravity wave forcing

Parameterization schemes for the drag due to atmospheric gravity waves are discussed and compared in the context of a simple one-dimensional model of the quasi-biennial oscillation (QBO). A number of fundamental issues are examined in detail, with the goal of providing a better understanding of the mechanism by which gravity wave drag can produce an equatorial zonal wind oscillation. The gravity wave–driven QBOs are compared with those obtained from a parameterization of equatorial planetary waves. In all gravity wave cases, it is seen that the inclusion of vertical diffusion is crucial for the descent of the shear zones and the development of the QBO. An important difference between the schemes for the two types of waves is that in the case of equatorial planetary waves, vertical diffusion is needed only at the lowest levels, while for the gravity wave drag schemes it must be included at all levels. The question of whether there is downward propagation of influence in the simulated QBOs is addressed. In the gravity wave drag schemes, the evolution of the wind at a given level depends on the wind above, as well as on the wind below. This is in contrast to the parameterization for the equatorial planetary waves in which there is downward propagation of phase only. The stability of a zero-wind initial state is examined, and it is determined that a small perturbation to such a state will amplify with time to the extent that a zonal wind oscillation is permitted.

Evaluation of moisture sources for the Central European summer flood of May/June 2013 based on regional climate model simulations

Heavy precipitation affected Central Europe in May/June 2013, triggering damaging floods both on the Danube and the Elbe rivers. Based on a modelling approach with COSMO-CLM, moisture fluxes, backward trajectories, cyclone tracks and precipitation fields are evaluated for the relevant time period 30 May–2 June 2013. We identify potential moisture sources and quantify their contribution to the flood event focusing on the Danube basin through sensitivity experiments: Control simulations are performed with undisturbed ERA-Interim boundary conditions, while multiple sensitivity experiments are driven with modified evaporation characteristics over selected marine and land areas. Two relevant cyclones are identified both in reanalysis and in our simulations, which moved counter-clockwise in a retrograde path from Southeastern Europe over Eastern Europe towards the northern slopes of the Alps. The control simulations represent the synoptic evolution of the event reasonably well. The evolution of the precipitation event in the control simulations shows some differences in terms of its spatial and temporal characteristics compared to observations. The main precipitation event can be separated into two phases concerning the moisture sources. Our modelling results provide evidence that the two main sources contributing to the event were the continental evapotranspiration (moisture recycling; both phases) and the North Atlantic Ocean (first phase only). The Mediterranean Sea played only a minor role as a moisture source. This study confirms the importance of continental moisture recycling for heavy precipitation events over Central Europe during the summer half year.