Crosslinking of polyimides via spirodilactone unit in polymer backbone

A new approach for the crosslinking of polyimides via the lactamization of spirodilactone unit in polyimide backbone was studied by two means: model reaction and the comparison of the properties of the polyimide precursors to those of the crosslinking polymers. Polyimides 4 and 5 were soluble in N,N'dimethylacetamide (DMAc), dimethylformamide (DMF), dimethylsulfoxide (DMSO), N'-methylpyrrolidone (NMP), and other common organic solvents, whereas their corresponding crosslinking polymers were insoluble in these solvents. The glass transition temperatures for polyimide 5 and its crosslinking polymer were 262 degrees C and 291 degrees C, whereas those for polyimide 4 and its crosslinking polymer were 265 degrees C and 360 degrees C. The weight-loss rate of the crosslinling polymers was apparently slower than that of the precursors when the temperature was >400 degrees C. The 10% weight-loss temperature for the polyimides 4 and 5 was <500 degrees C, whereas that for the crosslinking polymers was close to or above 600 degrees C. The results indicate that this type of crosslinking polymer has good thermal properties. The temperature for the formation of lactam was above 180 degrees C. (C) 1999 John Wiley & Sons, Inc.

Soluble 2,5-dimercapto-1,3,4-thiadiazole/poly(o-toluidine) electroactive composite

A poly(o-toluidine) (POT)/2,5-dimercapto-1,3,4-thiadiazole (DMcT) composite was prepared. When POT and DMcT are mixed in a proper solvent, POT in a medium-oxidation state is reduced, and DMcT in turn is oxidized to its soluble dimer when the molar ratio of DMcT to POT is higher than 0.5. Therefore, the composite was soluble in organic solvents such as tetrahydrofuran (THF), dimethylformamide (DMF), and N-methyl-2-pyrrolidone (NMP) and exhibited very high electroactivity, two orders of magnitude higher than that of pure POT and three orders of magnitude higher than that of pure DMcT. Molecular-level contact between POT and DMcT is the reason for the improved catalytic effect of POT on DMcT, compared to that of polyaniline on DMcT. (C) 1999 The Electrochemical Society. S0013-4651(98)08-059-8. All rights reserved.

Study on the structure of hemoglobin in organic solvents by in situ STM

In situ STM has been used to study the structure of hemoglobin(Hb) in two kinds of organic media. In hydrophobic organic solvent such as carbon tetrachloride, the structure of Hb is almost the same as in aqueous solution, similar to its native structure. However, when in hydrophilic organic solvent such as dimethylformamide, the two dimers of Hb molecule become separate and unfold to a certain extent.

Organic phase enzyme electrodes based on organohydrogel

A dimethylformamide-polyhydroxyl cellulose organo-hydrogel has been prepared, and its applications for enzyme immobilization in construction of organic phase biosensors have been exploited. With horseradish peroxidase, tyrosinase, and bilirubin oxidase immobilized in the organohydrogel, enzyme electrodes can be operated in various situations, including aqueous buffer, oil/water mixtures, and anhydrous organic solvents, and even in dimethylformamide, to determine analytes of different solubilities, e.g., organic peroxides, phenolic compounds and bilirubin. Biosensing has no restrictions in terms of measuring media and solubilities of analytes.

New progress in conducting polyaniline

New synthesis system was established to prepare polyaniline (PAn) with controlled molecular weight. The synthesized PAn was completely soluble in many organic solvents such as dimethylsulfoxide (DMSO), dimethylformamide and N-methylpyrrolidone (NMP). The molecular aggregation due to the interaction between PAn and NMP molecules was found in dilute PAn/NMP solution. The gelatin of concentrated PAn/NMP solution was a physical crosslinking between PAn molecules with the help of NMP through hydrogen bonding. A gelatin mechanism was proposed.

SYNTHESIS AND PHOTOCHROMISM IN SOLUTION OF PHENOXYNAPHTHACENEQUINONE DERIVATIVES

Two new phenoxynaphthacenequinone derivatives, 6-[4-(2-(4-hydroxyphenyl)isopropyl)phenoxy] -5,12-naphthacenequinone (7) and 6-[4-(potassium sulfophenylazo)phenoxy]-5,12-naphthacenequinone (8), were synthesized, and their photochromism in solution was investigated and compared with that of 6-phenoxy-5,12-naphthacenequinone (1). On the basis of the spectral data and the selective irreversible reaction of ammonia with the colored phenoxy-ana-naphthacenequinone, the concentrations of the ana forms at the photostationary state (PSS), achieved by 365 nm UV irradiation, and the molar extinction coefficients of the pure ana forms at 481-482 nm of compounds 1, 7 and 8 in dimethylsulfoxide (DMSO) were found to be 83 mol.% and 1.70x10(4) mol(-1) dm(3) cm(-1), 82 mol.% and 1.62x10(4) mol(-1) dm(3) cm(-1) and 16 mol.% and approximately 1.34x10(4) mol(-1) dm(3) cm(-1) respectively; the absorption spectra of the colored ana forms of 7 and 1 in DMSO were estimated; the rate;constants of photoconversion induced by 365 nm light were obtained. The results show the strong effect of the structure of the phenoxynaphthacenequinones on their photochromism in solution. In addition to DMSO solution, compound 7 exhibited normal photochromism in toluene, benzene, chloroform and a DMSO-ethanol mixed solvent, but not in dimethylformamide (DMF) in which a photoinduced reaction occurred between 7 and DMF or impurities.

STUDY ON THE KINETIC PROCESS OF THE COMPLEX-REACTION BETWEEN BILIRUBIN AND CYCLODEXTRINS

The complex behavior of bilirubin (BR) with beta-CD (cyclodextrin) and gamma-CD in aqueous and dimethylformamide (DMF) solution was investigated by absorption spectroscopy and cyclic voltammetry, respectively. The data shows that the complexation mechanis

INVESTIGATION ON MECHANISMS FOR THE ELECTROOXIDATION OF SOME BILE-PIGMENTS BY SPECTROELECTROCHEMISTRY

The electrooxidation behavior of bilirubin (BR), biliverdin (BV), purpurin (Pu), and choletelin (Ch in dimethylformamide (DMF) have been investigated bv voltammetry, in situ electron spin resonance (ESR) thin-layer spectroelectrochemistry and especially i

Determination of free fatty acids in soil and bryophyte plants by precolumn derivatization via HPLC with fluorescence detection and tandem mass spectrometry (HPLC-MS/MS)

A sensitive method for the determination of 30 kinds of free fatty acids (FFAs, C-1-C-30) with 1-[2-(p-toluenesulfonate)-ethyl]-2-phenylimidazole-[4,5-f] 9,10-phenan- threne (TSPP) as labeling reagent and using high performance liquid chromatography with fluorescence detection and identification by online postcolumn mass spectrometry with atmospheric pressure chemical ionization (APCI) source in positive-ion mode (HPLC/MS/APCI) has been developed. TSPP could easily and quickly label FFAs in the presence of K2CO3 catalyst at 90 degrees C for 30 min in N,N-dimethylformamide (DMF) solvent, and maximal labeling yields close to 100% were observed with a 5-fold excess of molar reagent. Derivatives were stable enough to be efficiently analyzed by high performance liquid chromatography. TSPP was introduced into fatty acid molecules and effectively augmented MS ionization of fatty acid derivatives and led to regular MS and MS/MS information. The collision induced cleavage of protonated molecular ions formed specific fragment ions at m/z [MH](+)(molecular ion), m/z [M'+CH2CH2](+)(M' was molecular mass of the corresponding FFA) and m/z 295.0 (the, mass of protonated molecular core structure of TSPP). Fatty acid derivatives were separated on a reversed-phase Eclipse XDB-C-8 column (4.6 x 150 mm, 5 mu m, Agilent) with a good baseline resolution in combination with a gradient elution. Linear ranges of 30 FFAs are 2.441 x 10(-3) to 20 mu mol/L, detection limits are 3.24 similar to 36.97 fmol (injection volume 10 mu L, at a signal-to-noise ratio of 3, S/N 3:1). The mean interday precision ranged from 93.4 to 106.2% with the largest mean coefficients of variation (R.S.D.) < 7,5%. The mean intraday precision for all standards was < 6.4% of the expected concentration. Excellent linear responses were observed with correlation coefficients of > 0.9991. Good compositional data could be obtained from the analysis of extracted fatty acids from as little as 200 mg of bryophyte plant samples.Therefore, the facile TSPP derivatization coupled with HPLC/MS/APCI analysis allowed the development of a highly sensitive method for the quantitation of trace levels of short and long chain fatty acids from biological and natural environmental samples.

Determination of 30 free fatty acids in two famous Tibetan medicines by HPLC with fluorescence detection and mass spectrometric identification

A simple and sensitive high-performance liquid chromatographic (HPLC) method with fluorescence detection and mass spectrometric identification has been developed for analysis of 30 long-chain and short-chain free Fatty acids (FFAs). The fatty acids were derivatized to their esters with 1-[2-(p-toluenesulfonate)ethyl]-2-phenylimidazole-[4,5-f]-9,10-phenanthrene (TSPP) in N,N-dimethylformamide (DMF) at 90 degrees C with anhydrous K2CO3 as catalyst. A mixture Of C-1-C-30 fatty acids was completely separated within 60 min by gradient elution on a reversed-phase C-8 column. Qualitative identification of the acids was performed by atmospheric-pressure chemical ionization mass spectrometry (APCI-MS) in positive-ion mode. The fluorescence excitation and emission wavelengths were 260 and 380 nm, respectively. Quantitative determination of the 30 acids in two Tibetan medicines Gentiana straminea and G. dahurica was performed. The results indicated that the medicines contained many FFAs. Linear correlation coefficients for the FFA derivatives were > 0.9991. Relative standard deviations (RSDs, n = 6) for the fatty acid derivatives were < 3%. Detection limits (at a signal-to-noise ratio of 3:1) were 3.1-38 fmol. When the fatty acid derivatives were determined in the two real samples results were satisfactory and the sensitivity and reproducibility of the method were good.

Analysis of saturated free fatty acids from pollen by HPLC with fluorescence detection

A sensitive method for the determination of free fatty acids using 2-(2-(anthracen-10-yl)-1H-naphtho[2,3-dimidazol-1-yl) ethyl-p-toluenesuIfonate (ANITS) as tagging reagent with fluorescence detection has been developed. ANITS could easily and quickly label fatty acids in the presence of the K2CO3 catalyst at 90 degrees C for 40 min in N,N-dimethylformamide solvent. From the extracts of rape bee pollen samples, 20 free fatty acids were sensitively determined. Fatty acid derivatives were separated on a reversed-phase Eclipse XDB-C8 column by HPLC in conjunction with gradient elution. The corresponding derivatives were identified by post-column APCI/MS in positive-ion detection mode. ANITS-fatty acid derivatives gave an intense molecular ion peak at mlz [M+H](+); with MS/MS analysis, the collision-induced dissociation spectra of m/z [M+H](+) produced the specific fragment ions at mlz [M-345](+) and mlz 345.0 (here, m/z 345 is the core structural moiety of the ANITS molecule). The fluorescence excitation and emission wavelengths of the derivatives were lambda(ex) = 250 nm and lambda(em) = 512 nm, respectively. Linear correlation coefficients for all fatty acid derivatives are > 0.9999. Detection limits, at a signal-to-noise ratio of 3 : 1, are 24.76-98.79 fmol for the labeled fatty acids.

Changed reactivity of the 1-bromo-4-nitrobenzene radical anion in a room temperature ionic liquid

Radical anions of 1-bromo-4-nitrobenzene (p-BrC6H4NO2) are shown to be reactive in the room temperature ionic liquid N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide, ([C(4)mPyrr][NTf2]), by means of voltammetric measurements. In particular, they are shown to react via a DISP type mechanism such that the electrolysis of p-BrC6H4NO2 occurs consuming between one and two electrons per reactant molecule, leading to the formation of the nitrobenzene radical anion and bromide ions. This behaviour is a stark contrast to that in conventional non-aqueous solvents such as acetonitrile, dimethyl sulfoxide or N,N-dimethylformamide, which suggests that the ionic solvent promotes the reactivity of the radical anion, probably via stabilisation of the charged products.

Structuring reductive media containing protic ionic liquids and their application to the formation of metallic nanoparticles

Herein, we present a facile method for the formation of monodispersed metal nanoparticles (NPs) at room temperature from M^(III)Cl₃ (with M = Au, Ru, Mn, Fe or V) in different media based on N,N-dimethylformamide (DMF) or water solutions containing a protic ionic liquid (PIL), namely the octylammonium formate (denoted OAF) or the bis(2-ethyl-hexyl)ammonium formate (denoted BEHAF). These two PILs present different structures and redox-active structuring properties that influence their interactions with selected molecular compounds (DMF or water), as well as the shape and the size of formed metal NPs in these solutions. Herein, the physical properties, such as the thermal, transport and micellar properties, of investigated PIL solutions were firstly investigated in order to understand the relation between PILs structure and their properties in solutions with DMF or water. The formation of metal NPs in these solutions was then characterized by using UV–vis spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and dynamic light scattering (DLS) measurements. From our investigations, it appears that the PILs structure and their aggregation pathways in selected solvents affect strongly the formation, growths, the shape and the size of metal NPs. In fact by using this approach, the shape-/size-controlled metal NPs can be generated under mild condition. This approach suggests also a wealth of potential for these designer nanomaterials within the biomedical, materials, and catalysis communities by using designer and safer media based on PILs.

Tunable gold nanoparticles shape and size in reductive and structuring media containing protic ionic liquids

Herein, a facile method was developed for preparing high concentration of monodispersed gold nanoparticles (NPs) at room temperature from gold(III) chloride by using different media based on N,N-dimethylformamide or water solutions containing a protic ionic liquid (PIL), namely, the octylammonium formate or the bis(2-ethyl-hexyl)ammonium formate, based on which both PILs were used as redox-active structuring media. The formation of gold NPs in these systems was then characterized using UV-visible spectroscopy, transmission electron microscopy, and dynamic light scattering. From these investigations, it appears that the structure and aggregation pathway of PILs in selected solvents affect strongly the formation, growth, the shape, and the size of gold NPs. In fact, by using this approach, the shape-/ size-controlled gold NPs (branched and spherical) can be generated under mild condition. This approach suggests also a wealth of potential for these designer nanomaterials within the biomedical, materials, and catalysis communities by using designer and safer media based on PILs.

Caracterização e transformação de Lenhosulfonatos de Eucalyptus globulus

Os lenhosulfonatos representam um sub-produto formado durante o cozimento ao sulfito ácido, sendo queimados para a regeneração da base e recuperação de energia. No entanto, os lenhosulfonatos são também considerados uma importante matéria-prima para a produção de vários produtos de valor acrescentado. Os objectivos principais deste trabalho foram contribuir para uma melhor compreensão sobre a caracterização química e estrutural dos lenhosulfonatos do Eucalyptus globulus, assim como, para complementar a informação disponível sobre a síntese e a caracterização estrutural e térmica de materiais poliméricos obtidos a partir de compostos modelo dos produtos de oxidação dos lenhosulfonatos. O licor de cozimento ao sulfito foi analisado em termos do teor de cinzas, extractáveis, compostos voláteis, açúcares e lenhosulfonatos. O teor de cinzas e açúcares no licor de cozimento é muito elevado, tendo sido necessário purificar o mesmo (2,8-13,8 % e 3,2-9,1 %, respectivamente). A análise dos açúcares mostrou uma quantidade considerável de pentoses, sendo o açúcar predominante a xilose. Os lenhosulfonatos foram purificados, isolados e caracterizados por química molhada (titulação potenciométrica e oxidação com permanganato), análise elementar, espectroscopia de ultravioleta/visível (UV/Vis), espectroscopia de infravermelho de transformada de Fourier (FTIR), espectroscopia de ressonância magnética nuclear de protão (RMN de 1H) e carbono (RMN de 13C), espectrometria de massa de ionização por electrospray (ESI-MS), cromatografia de permeação em gel (GPC), termogavimetria (TGA) e calorimetria diferencial de varrimento (DSC). Os lenhosulfonatos são constituídos principalmente por unidades S, são parcialmente sulfonados e possuem um peso molecular relativamente baixo (Mw = 1250-2400 Da). A ruptura das ligações β-O-4 e α-O-4 da lenhina do Eucalyptus globulus após cozimento ao sulfito ácido originam olígomeros de baixo peso molecular cuja estrutura foi elucidada por RMN 1D/2D e ESI-MS. A degradação térmica dos lenhosulfonatos apresentou dois máximos de degradação a 188-190ºC e a 315-380ºC. As curvas de DSC mostraram um pico endotérmico para temperaturas inferiores a 130ºC e um pico exotérmico a 300-500ºC. Os lenhosulfonatos foram despolimerizados na presença de oxigénio molecular em meio alcalino. Os produtos de oxidação principais foram o aldeído siríngico, a vanilina, o ácido vanílico e o ácido siríngico. A adição do catalisador (sal de cobre) promoveu a oxidação dos lenhosulfonatos aumentando o rendimento dos aldeídos aromáticos (< 50%). A presença de açúcares nos lenhosulfonatos teve um efeito negativo no rendimento dos produtos de oxidação principais. Alguns compostos modelo dos produtos de oxidação dos lenhosulfonatos foram polimerizados por poliadição (catiónica e radicalar) e policondensação. Os monómeros e os polímeros foram caracterizados por espectroscopia de infravermelho de transformada de Fourier e reflectância total atenuada (FTIR-ATR), RMN em solução e no estado sólido, UV/Vis no estado sólido, GPC, difracção de raios-X (XRD), TGA e DSC. Os compostos modelo estudados foram os estirenos metoxi-substituídos (p-metoxiestireno e 3,4-dimetoxiestireno) e os ácidos hidroxi aromáticos metoxi-substituídos (ácido vanílico e ácido siríngico). O 3,4-dimetoxiestireno foi ainda copolimerizado com o éter isobutil vinílico e os seus copolímeros foram desmetilados, assim como, o poli(p-metoxiestireno) e o poli(3,4-dimetoxiestireno). A polimerização catiónica do p-metoxiestireno e 3,4-dimetoxiestireno é mais rápida e mais completa do que a polimerização radicalar produzindo polímeros com pesos moleculares elevados. O poli(p-metoxiestireno) (Mw = 235000 Da) possui um peso molecular maior do que o poli(3,4-dimetoxiestireno) (Mw = 18800 Da). A estabilidade térmica e a temperatura de transição vítrea diminuiram com a presença do segundo grupo metoxilo. A desmetilação dos homopolímeros foi bem sucedida, tendo sido corroborada por FTIR-ATR e RMN. A policondensação do ácido siríngico foi dificultada pela presença do segundo grupo metoxilo, tendo sido necessário adicionar uma maior quantidade do agente de condensação devido a factores estéricos. O poli(ácido vanílico) e poli(ácido siríngico) são insolúveis na maior parte dos solventes orgânicos, sendo parcialmente solúveis em clorofórmio, ácido triflúoracético, 1,1,2,2- tetracloroetano, dimetilsulfóxido, tetrahidrofurano, N,N’-dimetilformamida e 1,1,1,3,3,3-hexaflúor-2-propanol. A estabilidade térmica diminuiu com a presença do segundo grupo metoxilo e os dois polímeros não exibiram temperatura de transição vítrea. O poli(ácido vanílico) e poli(ácido siríngico) apresentaram uma estrutura muito cristalina (grau de cristalinidade 70% e 50%, respectivamente). O segundo grupo metoxilo aumentou o valor da absorvância, mas a forma do espectro de UV/Vis foi similar. A polimerização catiónica do éter isobutil vinílico resultou na produção de um polímero muito viscoso com peso molecular elevado (Mw = 20400 Da). A degradação térmica do polímero ocorreu em várias gamas de temperatura e foi completa (0% de resíduo a 800ºC). A copolimerização catiónica do 3,4-dimetoxiestireno com o éter isobutil vinílico foi realizada com proporções diferentes 80:20, 50:50 e 20:80. Os copolímeros apresentaram uma viscosidade elevada e um peso molecular baixo (Mw = 2000-4000 Da) que aumentou com a quantidade de éter isobutil vinílico. A degradação térmica dos copolímeros ocorreu também em várias gamas de temperatura, sendo a sua degradação completa (0,9-1,5% de resíduo a 800ºC). A desmetilação dos copolímeros não foi bem sucedida, tendo sido confirmada por FTIR-ATR e RMN.