熔制条件对铋酸盐玻璃性质的影响

采用传统的玻璃熔融法制备了组成为60Bi2O3-20B2O3-15SiO2-5La2O3(mol%)的铋酸盐玻璃， 系统研究了不同工艺过程对玻璃性能的影响. 分析了样品ICP的成分，扫描电镜，X-射线衍射谱， 差热分析和紫外-可见-近红外透过光谱测试. 结果表明：使用刚玉坩埚能提高玻璃的抗析晶稳定性 和透过率，陶瓷坩埚和白金坩埚均受到严重腐蚀，玻璃组分也随之发生很大变化. 当熔制温度从1 100 ℃变化到1 300 ℃时，玻璃的颜色从浅黄色变到深红棕色. 尤其是白金粒子被腐蚀进入玻璃液 后，玻璃中很容易形成纳米颗粒或者团聚形成胶体粒子，在玻璃中形成色散源，加深玻璃的颜色， 降低透过率. 1 300 ℃下，白金粒子起到晶核剂的作用，生成Bi2Pt2O7和BiB3O6晶相，导致玻璃失透.

Preparação, caracterização e avaliação de nanocompósitos de PBAT/amido de milho e vermiculita organofilizada

Nos últimos 20-30 anos polímeros biodegradáveis vêm sendo estudados e desenvolvidos e atualmente já são comercializados. Contudo, o custo, a processabilidade e algumas propriedades ainda dificultam a penetração desses polímeros no mercado e a competição com as chamadas commodities. Não são poucos os autores que se dedicam a desenvolver aditivos e formulações para superar essas limitações. Desta forma, esta Tese se dedicou ao desenvolvimento de compósitos de Ecobras, fabricado pela Basf e comercializado pela Corn Products, utilizando como carga mineral resíduo da extração da bauxita, no município de Santa Luzia/PB, o qual consiste em sua totalidade de vermiculita. Esta vermiculita foi quimicamente modificada com sais de alquil fosfônio para melhorar a compatibilidade com a matriz polimérica e também espaçar as camadas de aluminossilicato. De fato, a modificação com o brometo de hexadecil tributil fosfônio resultou na esfoliação da vermiculita tornando-a potencialmente apropriada para a obtenção de nanocompósitos. A preparação dos compósitos foi realizada pelo método de intercalação no estado fundido e foram comparadas a utilização da câmara interna de mistura e da mini extrusora de dupla rosca, sendo esta última mais eficaz na dispersão da vermiculita, conforme revelado pela microscopia eletrônica de varredura, difração de raios-X e reometria de placas. O grau de dispersão também foi influenciado pela estrutura química do modificador da vermiculita e pelo teor dessa carga incorporada à matriz. Teores mais elevados levaram a formação de aglomerados, enquanto a modificação da carga implicou na formação de micro e nanocompósitos. Ainda houve alterações das propriedades térmicas com aumento dos valores da temperatura de transição vítrea, de cristalização e fusão, embora o grau de cristalinidade tenha sido mantido. Nitidamente, foram obtidos materiais mais rígidos, com maior módulo e menor capacidade de deformação. Cerca de 58% de perda de massa foi observada para os micro e nanocompósitos obtidos após 17 semanas de enterro em solo simulado para avaliação da biodegradabilidade, valor bem próximo ao Ecobras puro. De modo geral, a incorporação das diferentes vermiculitas retardou nas primeiras semanas a biodegradação, provavelmente em função de modificações na estrutura cristalina, conforme sugerido pelos maiores valores de temperatura de fusão observados durante o acompanhamento do processo de biodegradação. No entanto, após 7 semanas os perfis de biodegradação dos micro e nanocompósitos se aproximaram bastante do Ecobras puro. Desta forma, foi possível nesta Tese obter um nanocompósito de Ecobras com vermiculita modificada com brometo de hexadecil fosfônio utilizando ferramentas comuns de processamento no estado fundido com biodegradabilidade próxima ao polímero de partida, porém mais rígido e menos deformável

Enhanced Thermal Shock Resistance of Ceramics through Biomimetically Inspired Nanofins

We propose here a new method to make ceramics insensitive to thermal shock up to their melting temperature. In this method the surface of ceramics was biomimetically roughened into nanofinned surface that creates a thin air layer enveloping the surface of the ceramics during quenching. This air layer increases the heat transfer resistance of the surface of the ceramics by about 10 000 times so that the strong thermal gradient and stresses produced by the steep temperature difference in thermal shock did not occur both on the actual surface and in the interior of the ceramics. This method effectively extends the applications of existing ceramics in the extreme thermal environments.

Research on metallic ion beam production at IMP

Since 1998, many experiments for metallic ion production have been done on LECR2 (Lanzhou ECR ion source NO.2), LECR3 (Lanzhou ECR ion source NO.3) and SECRAL (Superconductiong ECR ion source Advanced design in Lanzhou) at Institute of Modern Physics. The very heavy metallic ion beams such as those of uranium were also produced by the plasma sputtering method, and supplied for HIRFL (Heavy Ion Research Facility in Lanzhou) accelerators successfully. During the test, 11.5e mu AU(28+), 9e mu AU(24+) were obtained. Some ion beams of the metal having lower melting temperature such as Ni and Mg ion beams were produced by oven method on LECR3 too. The consumption rate was controlled to be lower for Mg-26 ion beams production, and the minimum consumption was about 0.3mg per hour. In this paper, the main experimental results are given. Some discussions are made for some experimental phenomena and results, and some conclusions are drawn.

Heat capacity and enthalpy of fusion of pyrimethanil laurate (C24H37N3O2)

Low-temperature heat capacities of pyrimethanil laurate (C24H37N3O2) were precisely measured with an automated adiabatic calorimeter over the temperature range between T = 78 K and T = 340 K. The sample was observed to melt at (321.52 +/- 0.04) K. The molar enthalpy and entropy of fusion as well as the chemical purity of the compound were determined to be (67244 +/- 11) J (.) mol(-1), (209.28 +/- 0.02) J (.) mol(-1) (.) K-1, (0.9943 +/- 0.0004) mass fraction, respectively. The extrapolated melting temperature for the absolutely pure compound obtained from fractional melting experiments was (322.264 +/- 0.006) K. (C) 2004 Elsevier Ltd. All rights reserved.

Effect of gamma-radiation on the thermal and mechanical properties of a commercial poly(butylene adipate-co-terephthalate)

BACKGROUND: Poly(butylene adipate-co-terephthalate) (PBAT) has attracted wide interest as a biodegradable polymer. However, its use is restricted in certain applications due to its low melting point.RESULTS: PBAT was treated using gamma-radiation. The radiation features were analyzed using Soxhlet extraction, and the ratio of chain scission and crosslinking and gelation dose were determined using the classical Charlesby-Pinner equation. The results showed that PBAT is a radiation-crosslinkable polymer. The degree of crosslinking increased with increasing radiation dose; the relation between sol fraction and dose followed the Charlesby-Pinner equation. Differential scanning calorimetry analyses showed that the melting temperature (T-m) and the heat of fusion (Delta H-m) of PBAT exhibited almost no change in the first scan. The second scan, however, showed a decrease in T-m and Delta H-m. The glass transition temperature of irradiated PBAT increased with increasing radiation dose.

Effect of peroxide crosslinking on thermal and mechanical properties of poly(epsilon-caprolactone)

Poly(epsilon-caprolactone) (PCL), a saturated polyester, derived from ring-opening polymerization of epsilon-caprolactone, was chemically crosslinked with various amounts of benzoyl peroxide (BPO) by a two-step method by first evenly dispersing the BPO into the PCL matrix and then crosslinking at elevated temperature. The gel fraction increased with an increase in BPO content. The modified Charlesby-Pinner equation was used to calculate the ratio of chain scission and crosslinking. The results showed that both scission and crosslinking occurred, and that crosslinking predominated over scission. The number-average molecular weight between the crosslinks determined by the rubber elasticity theory using the hot set test showed a decrease with increasing BPO content. The melting temperature and crystallinity decreased with an increase in BPO content, and the crystallization temperature increased after crosslinking. Dynamic mechanical analysis results showed a decrease in the glass transition temperature as a result of chemical crosslinking of PCL. This was explained by the observed reduction in crystallinity and the increase in free volume due to restrictions in chain packing.

Crosslinked poly (epsilon-caprolactone) initiated by benzoyl peroxide

Poly(epsilon-caprolactone) (PCL) was chemically crosslinked with various amounts of benzoyl peroxide (BPO) The effect of BPO contents, crosslinking temperature and time on the crosslinking reaction was studied. The thermal, mechanical, and biodegradable properties of crosslinked PCL were also examined by DSC and DMA etc. The results showed that the melting temperature, crystallinity and glass transition temperature decreased with increase in BPO contents, while the crystallization temperature increased with increase in BPO content. The Young's modulus and elongation at break generally decreased with increase in BPO content. Moreover, the crosslinked PCL still had biodegradable ability.

Energetic basis of molecular recognition in a DNA aptamer

The thermal stability and ligand binding properties of the L-argininamide-binding DNA aptamer (5'-GATCGAAACGTAGCGCCTTCGATC3') were studied by spectroscopic and calorimetric methods. Differential calorimetric studies showed that the uncomplexed aptamer melted in a two-state reaction with a melting temperature T-m = 50.2 +/- 0.2 degrees C and a folding enthalpy Delta H degrees(fold) = -49.0 +/- 2.1 kcal mol(-1). These values agree with values of T-m = 49.6 degrees C and Delta H degrees(fold) = -51.2 kcal mol(-1) predicted for a simple hairpin structure. Melting of the uncomplexed aptamer was dependent upon salt concentration, but independent of strand concentration. The T of aptamer melting was found to increase as L-argininamide concentrations increased. Analysis of circular dichroism titration data using a single-site binding model resulted in the determination of a binding free energy Delta G degrees(bind) = -5.1 kcal mol(-1). Isothermal titration calorimetry studies revealed an exothermic binding reaction with Delta H degrees(bind) = -8.7 kcal mol(-1). Combination of enthalpy and free energy produce ail unfavorable entropy of -T Delta S degrees = +3.6 kcal mol(-1). A molar heat capacity change of -116 cal mol(-1) K-1 was determined from calorimetric measurements at four temperatures over the range of 15-40 degrees C. Molecular dynamics simulations were used to explore the structures of the unligated and ligated aptamer structures.

Study of beta-alpha recrystallization of the polypropylene

The crystalline modifications alpha and beta of polypropylene (PP) were studied by using polarized light microscopy (PLM), wide-angle X-ray diffraction (WAXD), and differential scanning calorimetry (DSC). Typically beta crystals surrounded by alpha spherulites were observed at low temperature. With increasing temperature the beta crystals melted and a new crystal appeared. More interestingly, the melting temperature of the new crystal was about 5degrees higher than that of alpha spherulites originally present in the sample formed isothermally. It was assumed that this new crystal was the recrystalline alpha crystal. This assumption was supported by the DSC results. Furthermore, the crystallization kinetics of the PP used was studied on the basis of the traditional Avrami analysis. As a result, the Avrami exponents of crystallization temperature from 120 to 130degreesC ranged between 4.21 and 3.60, indicating that the crystallization mechanism of PP order melt was spherulitic growth and random nucleation.

The mechanical and thermal behaviors of glass bead filled polypropylene

Notch Izod impact strength of poly(propylene) (PP)/glass bead blends was studied as a function of temperature. The results indicated that the toughness for various blends could undergo a brittle-ductile transition (BDT) with increasing temperature. The BDT temperature (T-BD) decreased with increasing glass bead content. Introducing the interparticle distance (ID) concept into the study, it was found that the critical interparticle distance (IDc) reduced with increasing test temperature correspondingly. The static tensile tests showed that the Young's modulus of the blends decreased slightly first and thereafter increased with increasing glass bead content. However, the yield stress decreased considerably with the increase in glass bead content. Dynamic mechanical analysis (DMA) measurements revealed that the heat-deflection temperature of the PP could be much improved by the incorporation of glass beads. Moreover, the glass transition temperature (T-g) increased obviously with increasing glass beads content. Differential scanning calorimetry (DSC) results implied that the addition of glass beads could change the crystallinity as well as the melting temperature of the PP slightly.

The critical lowest molecular weight for PEG to crystallize in cross-linked networks

Poly(ethylene glycol) (PEG) networks were synthesized by gamma-irradiation. The crystalline behavior of PEG was investigated by differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD). It was shown that the crystallinity of PEG is dramatically lower in the cross-linked, networks than in pure PEG. When the molecular weight of PEG in the networks decreased to 1000, it could not crystallize at all. Moreover, we also found that the melting temperature of PEG is greatly affected by the presence of a cross-linked network.

Thermal analysis of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) irradiated under vacuum

Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) was irradiated by Co-60 gamma-rays (doses of 50, 100 and 200kGy) under vacuum. The thermal analysis of control and irradiated PHBV, under vacuum was carried out by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The tensile properties of control and irradiated PHBV were examined by using an Instron tensile testing machine. In the thermal degradation of control and irradiated PHBV, a one-step weight loss was observed. The derivative thermogravimetric curves of control and irradiated PHBV confirmed only one weight-loss step change. The onset degradation temperature (T-o) and the temperature of maximum weight-loss rate (T-p) of control and irradiated PHBV were in line with the heating rate (degreesC min(-1)). T-o and T-p of PHBV decreased with increasing radiation dose at the same heating rate. The DSC results showed that Co-60 gamma-radiation significantly affected the thermal properties of PHBV. With increasing radiation dose, the melting temperature (T-m) of PHBV shifted to a lower value, due to the decrease in crystal size. The tensile strength and fracture strain of the irradiated PHBV decreased, hence indicating an increased brittleness.

Stereoselective polymerization of rac-lactide with a bulky aluminum/Schiff base complex

An aluminum/Schiff base complex {[2,2-dimethyl-1,3-propylenebis(3,5-di-tert-butylsalicylideneiminato)](isopropanolato)aluminum(III) (2)} based on a bulky ligand and aluminum isopropoxide was prepared and employed for the stereoselective ring-opening polymerization (ROP) of rac-lactide (rac-LA). The initiator was characterized with nuclear magnetic resonance (NMR), crystal structure measurements, and elemental analysis. It contained a five-coordinate aluminum atom that was trigonal bipyramidal in the solid state according to the crystal structure measurements. The two conformational stereoisomers of 2 exchanged quickly on the NMR scale. Compound 2 polymerized rac-LA into a crystalline polymer that was characterized with H-1 NMR, wide-angle X-ray diffraction, electrospray ionization mass spectrometry, and gel permeation chromatography. The kinetics of the polymerization were first-order in both the monomer and initiator, and there was a linear relationship between the rac-LA conversion and the number-average molecular weight of poly(rac-LA) with a narrow molecular distribution (1.04-1.08). These features showed that the polymerization was well controlled. The high melting temperature (196-201 degreesC) and isotacticity of poly(rac-LA) indicated that complex 2 was a highly stereoselective initiator for the ROP of rac-LA.

Stereoselective polymerization of rac-lactide using a monoethylaluminum Schiff base complex

A monoethylaluminum Schiff base complex (2) with formula LA1Et (L = N,N'-(2,2-dimethylpropylene)bis(3,5-di-tei-t-butylsalicylideneimine) was synthesized and employed for the stercoselective ring-opening polymerization of rac-lactide (rac-LA). The complex 2 was characterized by nuclear magnetic resonance, crystal structure, and elemental analysis. It contains a five-coordinate aluminum atom with distorted trigonal bipyramidal geornetry in the solid state. In the presence of 2-propanol, 2 showed high stereoselectivity for the polymerization of rac-LA. The polymerization yielded crystalline poly(rac-LA) with a high melting temperature (193-201 degreesC). NMR, differential scanning calorimetry, and wide-angle X-ray diffraction indicated that the poly(rac-LA) was highly isotactic, and a stereocomplex was formed between poly-L- and poly-D-lactide block sequences. By the analysis of electrospray-ionization mass spectrometry and H-1 NMR, the polymer was demonstrated to be endcapped in both terminals with an isopropyl ester and a hydroxy group, respectively. The polymerization was of first order in rac-LA concentration. The relationship between the rac-LA conversion and molecular weights of the polymer was linear so that the polymerization could be well controlled.