Characterization of amine-based CO2 adsorbent for Direct Air Capture

Direct air capture technologies extract CO2 from air at a concentration of as low as 400ppm. The captured CO2 can be used for the production of synthetic methane or liquid fuels. In the literature survey of this thesis, results related to direct air capture by using solid sorbents are presented and critically discussed. In the experimental part, a proprietary amine functionalized resin is characterized for direct air capture. Structural comparison is also made to a commercial resin of similar type. Based on the literature survey, the most important parameters in direct air capture process are low adsorption and desorption temperatures, good cyclic stability in dry and humid conditions, high CO2 outlet purity and a high working capacity. Primary amine functionalized solid sorbents are found to often have good qualities for direct air capture, but overall process performance is rarely studied exhaustively. Based on FTIR spectra, both resin adsorbents are found to be consisted of polystyrene functionalized with primary amine, and capture CO2 by forming carbamate. The commercial resin is more porous, has a slightly higher particle size and contains fewer impurities. Important physical parameters are gained of the proprietary resin, such as internal porosity and median particle size. The resin’s amine group is found to endure thermal treatment reasonably well. CO2 adsorption capacity gained by thermal gravimetry from 400ppm CO2 is highest at 25oC, and is found to be reasonable compared to values presented in literature. Thus, the resin is stated to exhibit promising qualities for direct air capture.

Biomassaperäisen liuoksen fraktiointi membraanisuodatuksella

Työn tavoitteena oli hiilihydraattien ja aminohappojen talteenotto biomassaperäisistä liuoksista erilaisina fraktioina ultra- ja nanosuodattamalla niitä erilaisilla membraaneilla. Työ tehtiin selvitystyönä Senson Oy:lle syystalven 2015 ja kevään 2016 välisenä aikana. Teoriaosassa perehdyttiin nanosuodatukseen ja sen erilaisiin sovelluksiin teollisuudessa, sekä lyhyesti muihin paineavusteisiin membraanisuodatusprosesseihin. Teoriaosassa myös keskityttiin erityisesti nanosuodatuksessa käytettyihin membraaneihin sekä niiden likaantumismekanismeihin. Kokeellisessa osassa keskityttiin hiilihydraattien ja aminohappojen talteenottoon kolmesta biomassaperäisestä liuoksesta. Tutkimuksen osa-alueita olivat ultrasuodatus, ultrasuodatuksen konsentraatin kirkastaminen sekä ultrasuodatuksen permeaatin fraktiointi nanosuodatuksella. Tutkimuksessa kiinnitettiin myös erityistä huomiota suodatuskalvojen likaantumiseen ja peseytyvyyteen sekä kalvojen käytettävyyteen pesujen jälkeen. Ultrasuodatuksessa kaikkien kolmen liuoksen kohdalla tutkittavien hiilihydraattien saanto permeaattiin oli hyvä, noin 90 %. Ultrasuodatuksissa käytettyjen membraanien osalta ei myöskään ollut havaittavissa merkittävää likaantumista. Ultrasuodatuksen konsentraattien kirkastamiskokeissa sameutta aiheuttavat komponentit saatiin poistettua kaikista liuoksista yli 94 %:in tehokkuudella. Nanosuodatuksissa monosakkaridit saatiin erotettua suuremmista hiilihydraattikomponenteista joko täysin tai lähes täysin (97 - 100 %). Nanosuodatuksissa käytettyjen membraanien osalta huomattavaa likaantumista oli havaittavissa vain membraanilla 2. Tulosten perusteella nanosuodatuksen voidaan sanoa olevan tehokas tapa erottaa pienet monosakkaridit suuremmista hiilihydraattiyhdisteistä.

Liquid-phase alcohol promoted methanol synthesis from CO2 and H2

Methanol is an important and versatile compound with various uses as a fuel and a feedstock chemical. Methanol is also a potential chemical energy carrier. Due to the fluctuating nature of renewable energy sources such as wind or solar, storage of energy is required to balance the varying supply and demand. Excess electrical energy generated at peak periods can be stored by using the energy in the production of chemical compounds. The conventional industrial production of methanol is based on the gas-phase synthesis from synthesis gas generated from fossil sources, primarily natural gas. Methanol can also be produced by hydrogenation of CO2. The production of methanol from CO2 captured from emission sources or even directly from the atmosphere would allow sustainable production based on a nearly limitless carbon source, while helping to reduce the increasing CO2 concentration in the atmosphere. Hydrogen for synthesis can be produced by electrolysis of water utilizing renewable electricity. A new liquid-phase methanol synthesis process has been proposed. In this process, a conventional methanol synthesis catalyst is mixed in suspension with a liquid alcohol solvent. The alcohol acts as a catalytic solvent by enabling a new reaction route, potentially allowing the synthesis of methanol at lower temperatures and pressures compared to conventional processes. For this thesis, the alcohol promoted liquid phase methanol synthesis process was tested at laboratory scale. Batch and semibatch reaction experiments were performed in an autoclave reactor, using a conventional Cu/ZnO catalyst and ethanol and 2-butanol as the alcoholic solvents. Experiments were performed at the pressure range of 30-60 bar and at temperatures of 160-200 °C. The productivity of methanol was found to increase with increasing pressure and temperature. In the studied process conditions a maximum volumetric productivity of 1.9 g of methanol per liter of solvent per hour was obtained, while the maximum catalyst specific productivity was found to be 40.2 g of methanol per kg of catalyst per hour. The productivity values are low compared to both industrial synthesis and to gas-phase synthesis from CO2. However, the reaction temperatures and pressures employed were lower compared to gas-phase processes. While the productivity is not high enough for large-scale industrial operation, the milder reaction conditions and simple operation could prove useful for small-scale operations. Finally, a preliminary design for an alcohol promoted, liquid-phase methanol synthesis process was created using the data obtained from the experiments. The demonstration scale process was scaled to an electrolyzer unit producing 1 Nm3 of hydrogen per hour. This Master’s thesis is closely connected to LUT REFLEX-platform.