Investigation of EDFA power transients in circuit-switched and packet-switched optical networks

Erbium-doped fibre amplifiers (EDFA’s) are a key technology for the design of all optical communication systems and networks. The superiority of EDFAs lies in their negligible intermodulation distortion across high speed multichannel signals, low intrinsic losses, slow gain dynamics, and gain in a wide range of optical wavelengths. Due to long lifetime in excited states, EDFAs do not oppose the effect of cross-gain saturation. The time characteristics of the gain saturation and recovery effects are between a few hundred microseconds and 10 milliseconds. However, in wavelength division multiplexed (WDM) optical networks with EDFAs, the number of channels traversing an EDFA can change due to the faulty link of the network or the system reconfiguration. It has been found that, due to the variation in channel number in the EDFAs chain, the output system powers of surviving channels can change in a very short time. Thus, the power transient is one of the problems deteriorating system performance. In this thesis, the transient phenomenon in wavelength routed WDM optical networks with EDFA chains was investigated. The task was performed using different input signal powers for circuit switched networks. A simulator for the EDFA gain dynamicmodel was developed to compute the magnitude and speed of the power transients in the non-self-saturated EDFA both single and chained. The dynamic model of the self-saturated EDFAs chain and its simulator were also developed to compute the magnitude and speed of the power transients and the Optical signal-to-noise ratio (OSNR). We found that the OSNR transient magnitude and speed are a function of both the output power transient and the number of EDFAs in the chain. The OSNR value predicts the level of the quality of service in the related network. It was found that the power transients for both self-saturated and non-self-saturated EDFAs are close in magnitude in the case of gain saturated EDFAs networks. Moreover, the cross-gain saturation also degrades the performance of the packet switching networks due to varying traffic characteristics. The magnitude and the speed of output power transients increase along the EDFAs chain. An investigation was done on the asynchronous transfer mode (ATM) or the WDM Internet protocol (WDM-IP) traffic networks using different traffic patterns based on the Pareto and Poisson distribution. The simulator is used to examine the amount and speed of the power transients in Pareto and Poisson distributed traffic at different bit rates, with specific focus on 2.5 Gb/s. It was found from numerical and statistical analysis that the power swing increases if the time interval of theburst-ON/burst-OFF is long in the packet bursts. This is because the gain dynamics is fast during strong signal pulse or with long duration pulses, which is due to the stimulatedemission avalanche depletion of the excited ions. Thus, an increase in output power levelcould lead to error burst which affects the system performance.

Structural determinants of oligomerization of the aquaporin-4 channel

The aquaporins (AQP) family of integral membrane protein channels mediate cellular water and solute flow. Although qualitative and quantitative differences in channel permeability, selectivity, subcellular localization and trafficking responses have been observed for different members of the AQP family, the signature homotetrameric quaternary structure is conserved. Using a variety of biophysical techniques, we show that mutations to an intracellular loop (loop D) of human AQP4 reduce oligomerization. Non-tetrameric AQP4 mutants are unable to relocalize to the plasma membrane in response to changes in extracellular tonicity, despite equivalent constitutive surface expression levels and water permeability to wild-type AQP4. A network of AQP4 loop D hydrogen bonding interactions, identified using molecular dynamics simulations and based on a comparative mutagenic analysis of AQPs 1, 3 and 4, suggest that loop D interactions may provide a general structural framework for tetrameric assembly within the AQP family.

Sediment rates and structures in Bay of Kiel, Baltic Sea

Density and diversity of bottom fauna population as dependent on sediment types and water depth is largely well known in Kiel Bay. This is in contrast to structures and processes of bioturbation, although generally it has a big influence on the benthic boundary layer and its processes, e.g., the metabolism of the bottom fauna, the mechanical properties, the age dating, and the large field of chemical processes. In the densely inhabited sands and muddy sands of the shallower waters with sediment thicknesses of some decimeters only, bioturbation is usually ubiquitous, and most of the structures left are monotonously of "biodeformational" character. At greater water depths, however, where a sedimentary column of several meters of Holocene is developed, the X-ray radiographs of numerous sediment cores show heterogeneous biogenic structures with regional and stratigraphical differentiation. They are described in terms of ichnofabrics and are interpreted on ethological knowledge of the related macrobenthos species. lmportant organisms creating specific traces include the bivalve Arctica (Cyprina) islandica and the polychaete worm Pectinaria koreni. These species are abundant in Kiel Bay and produce by their crawling-plowing mode of locomotion, a characteristic biogenic stratification, the "plow-sole structure". Other typical biogenic structures are tube traces, which are left by a number of different polychaetes occurring either singly, or as U-pairs mainly in mud sediments. Although sea urchins are rare to absent in Kiel Bay, layers of their characteristic traces Scolicia occur as witness of paleohydrographic events in channel sediments of the central bay. Plow-sole traces, polychaete-tube ichnofabric, Scolicia layers and alternations of laminated and bioturbated layers are considered as building blocks of a future "ichnostratigraphy" of Kiel Bay.

A survey on prevalence rate of aflatoxigenic species of Aspergillus and residues of aflatoxins by ELISA method in cold-water cultural fish (rainbow trout) feeds in Tehran and West Azarbayjan provinces-Iran

Aflatoxins are one kind of fungal toxins produced by species of toxigenic Aspergillus (A. flavus and A. parasiticus) and in other words they are secondary metabolites which are considered as one of the threatening factors of food consumer's health. In this research 96 samples of cold-water cultural fish feed, rainbow trout, during the seasons of spring and summer of 2007 (every fifteenth of the month) were randomized (by simple and stratified random) to determine: 1. The prevalence rate of aflatoxigenic species of Aspergillus in stored feed of cold-water cultural fish in West Azarbayjan cultural fish farms in both seasons (spring and summer); 2. The residues of total aflatoxin in stored feed of fish in cultural fish farms of West Azarbayjan in both seasons by ELISA method; and 3. The residues of that toxin in feed produced in aquatic feed factories in Tehran and West Azarbyjan provinces with the same method. In order to study prevalence rate of toxigenic species of Aspergillus, pour-plate culture method by general medium such as Malt Extract Agar (M.E.A.) and Sabouraud-Dextrose Agar (S.D.A.) and by standard No.997 of Iranian Standard Institute were used. The produced colonies were examined microscopically. To determine the aflatoxins residues, ELISA method using Agra-Quant kit of Romer Lab company, were applied. The results of this survey indicated that only 8.3% of the samples were infected by A. flavus. A. parasiticus was not observed. There were no significant differences between the prevalence rate of AFT and seasons/months, either (P<0.05). Evaluating mean of aflatoxin rate showed that the rates of this variable are lower than the tolerance levels designated by the joint FAO/WHO expert committee (The mean of AFT in all data was lower than 11 ppb). Furthermore, mean of total AFT residues rates of stored feed of various cultural center of West Azarbayjan and Tehran factories were comparable in spring and summer, and no significant differences were observed (P<0.05). But there were significant differences between the total aflatoxin rates in the feed of West Azarbayjan factory and spring and summer (P<0.05), and AFT residues in spring (8.6 ppb) were higher than summer (6.1 ppb). Prevalence rates of AFT in Tehran feed factories (9.2 ppb) are higher than W. Azarbayjan (7.4 ppb). In other words, location was considered as a decisive factor in total AFT rates of samples. Moreover, the results indicated that there was significant difference between total aflatoxin rates of feed and cultural centers (P<0.05). The mean of AFT rates in embankment dam cultural fish farms (6.75 ppb) and multi-functions cultural fish farms (6.25 ppb) was higher than individual cultural pond (4.67 ppb). In conclusion, the finally results of this survey indicated that the lower rates of Aspergillus is not effective on the presence of total aflatoxin rates in trout feed. Due to low levels of aflatoxin rates (lower than 20 ppb), the produced feed of cold-cultural fishes, Rainbow Trout, in Tehran and West Azarbayjan provinces, in spring and summer of 2007, were safe and healthy both for fish and their consumers.

Studies of turbulent flows in continuous casting of steel with and without magnetic field

This thesis develops and tests various transient and steady-state computational models such as direct numerical simulation (DNS), large eddy simulation (LES), filtered unsteady Reynolds-averaged Navier-Stokes (URANS) and steady Reynolds-averaged Navier-Stokes (RANS) with and without magnetic field to investigate turbulent flows in canonical as well as in the nozzle and mold geometries of the continuous casting process. The direct numerical simulations are first performed in channel, square and 2:1 aspect rectangular ducts to investigate the effect of magnetic field on turbulent flows. The rectangular duct is a more practical geometry for continuous casting nozzle and mold and has the option of applying magnetic field either perpendicular to broader side or shorter side. This work forms the part of a graphic processing unit (GPU) based CFD code (CU-FLOW) development for magnetohydrodynamic (MHD) turbulent flows. The DNS results revealed interesting effects of the magnetic field and its orientation on primary, secondary flows (instantaneous and mean), Reynolds stresses, turbulent kinetic energy (TKE) budgets, momentum budgets and frictional losses, besides providing DNS database for two-wall bounded square and rectangular duct MHD turbulent flows. Further, the low- and high-Reynolds number RANS models (k-ε and Reynolds stress models) are developed and tested with DNS databases for channel and square duct flows with and without magnetic field. The MHD sink terms in k- and ε-equations are implemented as proposed by Kenjereš and Hanjalić using a user defined function (UDF) in FLUENT. This work revealed varying accuracies of different RANS models at different levels. This work is useful for industry to understand the accuracies of these models, including continuous casting. After realizing the accuracy and computational cost of RANS models, the steady-state k-ε model is then combined with the particle image velocimetry (PIV) and impeller probe velocity measurements in a 1/3rd scale water model to study the flow quality coming out of the well- and mountain-bottom nozzles and the effect of stopper-rod misalignment on fluid flow. The mountain-bottom nozzle was found more prone to the longtime asymmetries and higher surface velocities. The left misalignment of stopper gave higher surface velocity on the right leading to significantly large number of vortices forming behind the nozzle on the left. Later, the transient and steady-state models such as LES, filtered URANS and steady RANS models are combined with ultrasonic Doppler velocimetry (UDV) measurements in a GaInSn model of typical continuous casting process. LES-CU-LOW is the fastest and the most accurate model owing to much finer mesh and a smaller timestep. This work provided a good understanding on the performance of these models. The behavior of instantaneous flows, Reynolds stresses and proper orthogonal decomposition (POD) analysis quantified the nozzle bottom swirl and its importance on the turbulent flow in the mold. Afterwards, the aforementioned work in GaInSn model is extended with electromagnetic braking (EMBr) to help optimize a ruler-type brake and its location for the continuous casting process. The magnetic field suppressed turbulence and promoted vortical structures with their axis aligned with the magnetic field suggesting tendency towards 2-d turbulence. The stronger magnetic field at the nozzle well and around the jet region created large scale and lower frequency flow behavior by suppressing nozzle bottom swirl and its front-back alternation. Based on this work, it is advised to avoid stronger magnetic field around jet and nozzle bottom to get more stable and less defect prone flow.

Adaptive discontinuous Galerkin methods for eigenvalue problems arising in incompressible fluid flows

In this article we consider the a posteriori error estimation and adaptive mesh refinement of discontinuous Galerkin finite element approximations of the hydrodynamic stability problem associated with the incompressible Navier-Stokes equations. Particular attention is given to the reliable error estimation of the eigenvalue problem in channel and pipe geometries. Here, computable a posteriori error bounds are derived based on employing the generalization of the standard Dual-Weighted-Residual approach, originally developed for the estimation of target functionals of the solution, to eigenvalue/stability problems. The underlying analysis consists of constructing both a dual eigenvalue problem and a dual problem for the original base solution. In this way, errors stemming from both the numerical approximation of the original nonlinear flow problem, as well as the underlying linear eigenvalue problem are correctly controlled. Numerical experiments highlighting the practical performance of the proposed a posteriori error indicator on adaptively refined computational meshes are presented.

The judgments of Justice Lionel Murphy

Member of High Court Bench; includes references to Aboriginal voting rights; protection of Aboriginal sites in Franklin Dam Case; authors statements from cases - Onus v Alcoa of Australia Ltd, Portland; Neal v Queen, Yarrabah, Koowarta v BjelkePeterson, and Racial Discrimination Act 1975, Archer River; Queen v Toohey (Kenbi, Cox Peninsula); Coe v Commonwealth; Veen v Queen.

Common and rare variants of the renin-angiotensin system and their relation to antihypertensive drug responses

Most of the diseases affecting public health, like hypertension, are multifactorial by etiology. Hypertension is influenced by genetic, life style and environmental factors. Estimation of the influence of genes to the risk of essential hypertension varies from 30 to 50%. It is plausible that in most of the cases susceptibility to hypertension is determined by the action of more than one gene. Although the exact molecular mechanism underlying essential hypertension remains obscure, several monogenic forms of hypertension have been identified. Since common genetic variations may predict, not only to susceptibility to hypertension, but also response to antihypertensive drug therapy, pharmacogenetic approaches may provide useful markers in finding relations between candidate genes and phenotypes of hypertension. The aim of this study was to identify genetic mutations and polymorphisms contributing to human hypertension, and examine their relationships to intermediate phenotypes of hypertension, such as blood pressure (BP) responses to antihypertensive drugs or biochemical laboratory values. Two groups of patients were investigated in the present study. The first group was collected from the database of patients investigated in the Hypertension Outpatient Ward, Helsinki University Central Hospital, and consisted of 399 subjects considered to have essential hypertension. Frequncies of the mutant or variant alleles were compared with those in two reference groups, healthy blood donors (n = 301) and normotensive males (n = 175). The second group of subjects with hypertension was collected prospectively. The study subjects (n=313) underwent a protocol lasting eight months, including four one-month drug treatment periods with antihypertensive medications (thiazide diuretic, β-blocker, calcium channel antagonist, and an angiotensin II receptor antagonist). BP responses and laboratory values were related to polymorphims of several candidate genes of the renin-angiotensin system (RAS). In addition, two patients with typical features of Liddle’s syndrome were screened for mutations in kidney epithelial sodium channel (ENaC) subunits. Two novel mutations causing Liddle’s syndrome were identified. The first mutation identified located in the beta-subunit of ENaC and the second mutation found located in the gamma-subunit, constituting the first identified Liddle mutation locating in the extracellular domain. This mutation showed 2-fold increase in channel activity in vitro. Three gene variants, of which two are novel, were identified in ENaC subunits. The prevalence of the variants was three times higher in hypertensive patients (9%) than in reference groups (3%). The variant carriers had increased daily urinary potassium excretion rate in relation to their renin levels compared with controls suggesting increased ENaC activity, although in vitro they did not show increased channel activity. Of the common polymorphisms of the RAS studied, angiotensin II receptor type I (AGTR1) 1166 A/C polymorphism was associated with modest changes in RAS activity. Thus, patients homozygous for the C allele tended to have increased aldosterone and decreased renin levels. In vitro functional studies using transfected HEK293 cells provided additional evidence that the AGTR1 1166 C allele may be associated with increased expression of the AGTR1. Common polymorphisms of the alpha-adducin and the RAS genes did not significantly predict BP responses to one-month monotherapies with hydroclorothiazide, bisoprolol, amlodipin, or losartan. In conclusion, two novel mutations of ENaC subunits causing Liddle’s syndrome were identified. In addition, three common ENaC polymorphisms were shown to be associated with occurrence of essential hypertension, but their exact functional and clinical consequences remain to be explored. The AGTR1 1166 C allele may modify the endocrine phenotype of hypertensive patients, when present in homozygous form. Certain widely studied polymorphisms of the ACE, angiotensinogen, AGTR1 and alpha-adducin genes did not significantly affect responses to a thiazide, β-blocker, calcium channel antagonist, and angiotensin II receptor antagonist.

Direct numerical simulation of turbulent spots

A group of high-order finite-difference schemes for incompressible flow was implemented to simulate the evolution of turbulent spots in channel flows. The long-time accuracy of these schemes was tested by comparing the evolution of small disturbances to a plane channel flow against the growth rate predicted by linear theory. When the perturbation is the unstable eigenfunction at a Reynolds number of 7500, the solution grows only if there are a comparatively large number of (equispaced) grid points across the channel. Fifth-order upwind biasing of convection terms is found to be worse than second-order central differencing. But, for a decaying mode at a Reynolds number of 1000, about a fourth of the points suffice to obtain the correct decay rate. We show that this is due to the comparatively high gradients in the unstable eigenfunction near the walls. So, high-wave-number dissipation of the high-order upwind biasing degrades the solution especially. But for a well-resolved calculation, the weak dissipation does not degrade solutions even over the very long times (O(100)) computed in these tests. Some new solutions of spot evolution in Couette flows with pressure gradients are presented. The approach to self-similarity at long times can be seen readily in contour plots.

MRT Letter: Light Sheet Based Imaging Flow Cytometry on a Microfluidic Platform

We propose a light sheet based imaging flow cytometry technique for simultaneous counting and imaging of cells on a microfluidic platform. Light sheet covers the entire microfluidic channel and thus omits the necessity of flow focusing and point scanning based technology. Another advantage lies in the orthogonal detection geometry that totally cuts-off the incident light, thereby substantially reducing the background in the detection. Compared to the existing state-of-art techniques the proposed technique shows marked improvement. Using fluorescently-coated Saccharomyces cerevisiae cells we have recorded cell counting with throughput as high as 2,090 cells/min in the low flow rate regime and were able to image the individual cells on-the-go. Overall, the proposed system is cost-effective and simple in channel geometry with the advantage of efficient counting in operational regime of low laminar flow. This technique may advance the emerging field of microfluidic based cytometry for applications in nanomedicine and point of care diagnostics. Microsc. Res. Tech. 76:1101-1107, 2013. (c) 2013 Wiley Periodicals, Inc.

Controlling air solubility to maintain `'Cassie'' state for sustained drag reduction

`'Cassie'' state of wetting can be established by trapping air pockets on the crevices of textured hydrophobic surfaces, leading to significant drag reduction. However, this drag reduction cannot be sustained due to gradual dissolution of trapped air into water. In this paper, we explore the possibility of sustaining the underwater Cassie state of wetting in a microchannel by controlling the solubility of air in water; the solubility being changed by controlling the local absolute pressure near the surface. We show that using this method, we can in fact make the water locally supersaturated with air thus encouraging the growth of trapped air pockets on the surface. In this case, the water acts as a pumping medium, delivering air to the crevices of the hydrophobic surface in the microchannel, where the presence of air pockets is most beneficial from the drag reduction perspective. In our experiments, the air trapped on a textured surface is visualized using total internal reflection based technique, at different local absolute pressures with the pressure drop (or drag) also being simultaneously measured. We find that, by controlling the pressure and hence the solubility close to the surface, we can either shrink or grow the trapped air bubbles, uniformly over a large surface area. The experiments show that, by precisely controlling the pressure and hence the solubility we can sustain the `'Cassie state'' over extended periods of time. This method thus provides a means of getting sustained drag reduction from a textured hydrophobic surface in channel flows. (C) 2014 Elsevier B.V. All rights reserved.

Effect of nonuniform seismic input on arch dams

Standard earthquake analyses of civil engineering structures use uniform ground motions even though considerable variations in both amplitude and phase can occur along the foundation interface for long-span bridges and large dams. The objective of this thesis is to quantify the effect that these nonuniformities have on the structural response.

The nonuniform, free-field motions of the foundation interface are assumed to be caused by incident plane body waves. The medium in which these waves travel is a linear, elastic half-space containing a canyon of uniform cross section in which the structure is placed. The solutions for the free-field motions that are due to incident SH, P and SV waves are calculated using the boundary element method.

An analysis of Pacoima (arch) dam located near Los Angeles, California, is performed for both uniform and nonuniform excitations. The important effect of nonuniformities in the free-field motions, sometimes leading to a decrease in the dam response and sometimes to an increase, is quantified.

Introduction of boulders to the R. Ribble: a short geomorphological evaluation

The placement of artificial in-channel structures (including large cobbles / boulders) into any fluvial system needs to be considered carefully. This brief report summarises considerations for boulder introductions into the River Ribble from a geomorphological perspective. This includes boulder placement and shape. Bagnold's Excess Stream Power Method is used to calculate the boulder sizing.

Novel nonvolatile memory with multibit storage based on a ZnO nanowire transistor.

We demonstrate a room temperature processed ferroelectric (FE) nonvolatile memory based on a ZnO nanowire (NW) FET where the NW channel is coated with FE nanoparticles. A single device exhibits excellent memory characteristics with the large modulation in channel conductance between ON and OFF states exceeding 10(4), a long retention time of over 4 × 10(4) s, and multibit memory storage ability. Our findings provide a viable way to create new functional high-density nonvolatile memory devices compatible with simple processing techniques at low temperature for flexible devices made on plastic substrates.

Avaliaçāo preliminar do estado da exploraçāo de Kapenta (Limnothrissa miodon, Boulenger 1906), em cahora bassa com base em dados históricos de captura e esforço de 1995-2000

The fishing of kapenta (Limnothrissa miodon, Boulenger 1906) on the Cahora Bassa Dam started around 1992, when considerable stocks of this species were discovered in the lake. The species is believed to have successful established in the Dam following a natural introduction through a downstream movement from Kariba dam where it was introduced in 1967/68. Fisheries statistics on the kapenta fishery have been collected since 1993 by the Ministry of Fisheries through the Provincial Offices for Fisheries Administration of Tete (SPAP - Tete) but only data from 1995 onward are available on the database of the Ministry of Fisheries and these are the data that was used for compiling the present report on which trends of fishing effort, catch and CPUE are analyzed. Catch and effort have increased with time, from a minimum of the 4 thousand metric tons for an annual fishing effort of 36 fishing rigs in 1995 to a maximum of 12 tons for a fishing effort of 135 rigs while CPUE followed a decreasing trend during the same period. Correlation analysis between catch and effort suggests that probably environmental factors may have influence on catch variation than the increase on fishing effort. Two models were applied for calculating MSY and FMSY resulting in two pairs of roof leading to two scenario of fisheries management. 10137 tons and a FMSY of 177 fishing rigs were computed using Schaefer model while 11690 tons and a FMSY of 278 were obtained using Fox model. Considering the differences between the two results and considering the fact that the two models have no differences in terms of precision and the fact that their determination coefficient are not different it is suggested, using the precautionary principle that result from Schaefer model be a adopted for fisheries management purpose.