Micro-hardness evaluation of a micro-hybrid composite resin light cured with halogen light, light-emitting diode and argon ion laser

This in vitro study aimed to determine whether the micro-hardness of a composite resin is modified by the light units or by the thickness of the increment. Composite resin disks were divided into 15 groups (n = 5), according to the factors under study: composite resin thickness (0 mm, 1 mm, 2 mm , 3 mm and 4 mm) and light units. The light activation was performed with halogen light (HL) (40 s, 500 mW/cm(2)), argon ion laser (AL) (30 s, 600 mW/cm(2)) or light-emitting diode (LED) (30 s, 400 mW/cm(2)). Vickers micro-hardness tests were performed after 1 week and were carried out on the top surface (0 mm-control) and at different depths of the samples. Analysis of variance (ANOVA) and Tukey tests (P a parts per thousand currency signaEuro parts per thousand 0.05) revealed no statistically significant difference among the light units for the groups of 0 mm and 1 mm thickness. At 2 mm depth, the AL was not statistically different from the HL, but the latter showed higher micro-hardness values than the LED. In groups with 3 mm and 4 mm thickness, the HL also showed higher micro-hardness values than the groups activated by the AL and the LED. Only the HL presented satisfactory polymerization with 3 mm of thickness. With a 4 mm increment no light unit was able to promote satisfactory polymerization.

Effects of Nd:YAG Laser Irradiation on the Hybrid Layer of Different Adhesive Systems

Purpose: The aim of this in vitro study was to evaluate the microtensile bond strength (mu TBS) and hybrid layer morphology of different adhesive systems, either followed by treatment with Nd:YAG laser irradiation or not. Previous studies have shown the effects of Nd:YAG laser irradiation on the dentin surface at restoration margins, but there are few reports about the significance of the irradiation on the hybrid layer. Materials and Methods: The flattened coronal and root dentin samples of 24 bovine teeth were randomly divided into 8 groups, according to the adhesive system used - Scotchbond Multi Purpose (SBMP) or Clearfil SE Bond (CSEB) - and were either irradiated with Nd:YAG or not, with different parameters: 0.8 W/10 Hz, 0.8 W/20 Hz, 1.2 W/10 Hz, 1.2 W/20 Hz. The left sides of specimens were the control groups, and right sides were irradiated. A composite crown was built over bonded surfaces and stored in water (24 h at 37 degrees C). Specimens were sectioned vertically into slabs that were subjected to mu TBS testing and observed by SEM. Results: Control groups (27.81 +/- 1.38) showed statistically higher values than lased groups (21.37 +/- 0.99), and CSEB control group values (31.26 +/- 15.71) were statistically higher than those of SBMP (24.3 +/- 10.66). There were no significant differences between CSEB (20.34 +/- 10.01) and SBMP (22.43 +/- 9.82) lased groups. Among parameters tested, 0.8 W/10 Hz showed the highest value (25.54 +/- 11.74). Nd:YAG laser irradiation caused dentin to melt under the adhesive layer of both adhesive systems tested. Conclusion: With the parameters used in this study, Nd:YAG laser irradiation of the hybrid layer promoted morphological changes in dentin and negatively influenced the bond strength of both adhesive systems.

Development of a genetic method to estimate effective spawner numbers in the NPF and Queensland tiger prawn fisheries

OBJECTIVES: 1. To critically evaluate a variety of mathematical methods of calculating effective population size (Ne) by conducting comprehensive computer simulations and by analysis of empirical data collected from the Moreton Bay population of tiger prawns. 2. To lay the groundwork for the application of the technology in the NPF. 3. To produce software for the calculation of Ne, and to make it widely available.

The fluorolysis assay, a highly sensitive method for measuring the cytolytic activity of T cells at very low numbers

We have developed a highly sensitive cytolysis test, the fluorolysis assay, as a simple nonradioactive and inexpensive alternative to the standard Cr-51-release assay. P815 cells were stably transfected with a plasmid expressing the enhanced green fluorescent protein (EGFP) gene. These target cells were coated with or without cognate peptide or anti-CD3 Ab and then incubated with CD8(+) T cells to allow antigen-specific or nonspecific lysis. The degree of target cell lysis was measured using flow cytometry to count the percentage of viable propidium iodide(-) EGFP(+) cells, whose numbers were standardized to a reference number of fluorochrome-linked beads. By using small numbers of target cells (200-800 per reaction) and extended incubation times (up to 2 days), the antigen-specific cytolytic activity of one to two activated CD8(+) T cells of a CTL line could be detected. The redirected fluorolysis assay also measured the activity of very few ( greater than or equal to6) primary CD8(+) T cells following polyclonal activation. Importantly, antigen-specific lysis by small numbers ( greater than or equal to 25) of primary CD8(+) T cells could be directly measured ex vivo. This exquisite sensitivity of the fluorolysis assay, which was at least 8-33-folds higher than an optimized 51 Cr-release assay, allows in vitro and ex vivo studies of immune responses that would otherwise not be possible due to low CTL numbers or frequencies. (C) 2002 Elsevier Science B.V. All rights reserved.

Spatial structure and habitat variation in a grasshopper hybrid zone

A hybrid zone between the grasshoppers Chorthippus brunneus and C. jacobsi (Orthoptera: Acrididae) in northern Spain has been analyzed for variation in morphology and ecology. These species are readily distinguished by the number of stridulatory pegs on the hind femur. Both sexes are fully winged and inhabit disturbed habitats throughout the study area. We develop a maximum-likelihood approach to fitting a two-dimensional cline to geographical variation in quantitative traits and for estimating associations of population mean with local habitat. This method reveals a cline in peg number approximately 30 km south of the Picos de Europa Mountains that shows substantial deviations in population mean compared with the expectations of simple tension zone models. The inclusion of variation in local vegetation in the model explains a significant proportion of the residual variation in peg number, indicating that habitat-genotype associations contribute to the observed spatial pattern. However, this association is weak, and a number of populations continue to show strong deviations in mean even after habitat is included in the final model. These outliers may be the result of long-distance colonization of sites distant from the cline center or may be due to a patchy pattern of initial contact during postglacial expansion. As well as contrasting with the smooth hybrid zones described for Chorthippus parallelus, this situation also contrasts with the mosaic hybrid zones observed in Gryllus crickets and in parts of the hybrid zone between Bombina toad species, where habitat-genotype associations account for substantial amounts of among-site variation.

Impact numbers: measures of risk factor impact on the whole population from case-control and cohort studies

Objective: To describe new measures of risk from case-control and cohort studies, which are simple to understand and relate to numbers of the population at risk. Design: Theoretical development of new measures of risk. Setting: Review of literature and previously described measures. Main results: The new measures are: (1) the population impact number (PIN), the number of those in the whole population among whom one case is attributable to the exposure or risk factor (this is equivalent to the reciprocal of the population attributable risk),- (2) the case impact number (CIN) the number of people with the disease or outcome for whom one case will be attributable to the exposure or risk factor (this is equivalent to the reciprocal of the population attributable fraction); (3) the exposure impact number (EIN) the number of people with the exposure among whom one excess case is attributable to the exposure (this is equivalent to the reciprocal of the attributable risk); (4) the exposed cases impact number (ECIN) the number of exposed cases among whom one case is attributable to the exposure (this is equivalent to the reciprocal of the aetiological fraction). The impact number reflects the number of people in each population (the whole population, the cases, all those exposed, and the exposed cases) among whom one case is attributable to the particular risk factor. Conclusions: These new measures should help communicate the impact on a population, of estimates of risk derived from cohort or case-control studies.

Impact numbers in health policy decisions

Objective: To outline the major methodological issues appropriate to the use of the population impact number (PIN) and the disease impact number (DIN) in health policy decision making. Design: Review of literature and calculation of PIN and DIN statistics in different settings. Setting: Previously proposed extensions to the number needed to treat (NNT): the DIN and the PIN, which give a population perspective to this measure. Main results: The PIN and DIN allow us to compare the population impact of different interventions either within the same disease or in different diseases or conditions. The primary studies used for relative risk estimates should have outcomes, time periods and comparison groups that are congruent and relevant to the local setting. These need to be combined with local data on disease rates and population size. Depending on the particular problem, the target may be disease incidence or prevalence and the effects of interest may be either the incremental impact or the total impact of each intervention. For practical application, it will be important to use sensitivity analyses to determine plausible intervals for the impact numbers. Conclusions: Attention to various methodological issues will permit the DIN and PIN to be used to assist health policy makers assign a population perspective to measures of risk.

Genetic variation in foliar carbon isotope composition in relation to tree growth and foliar nitrogen concentration in clones of the F-1 hybrid between slash pine and Caribbean pine

The objectives of this study were: (1) to quantify the genetic variation in foliar carbon isotope composition (delta(13)C) of 122 clones of ca. 4-year-old F-1 hybrids between slash pine (Pinus elliottii Engelm var. elliottii) and Caribbean pine (Pinus caribaea var. hondurensis Barr.,et Golf.) grown at two field experimental sites with different water and nitrogen availability in southeast Queensland, Australia, in relation to tree growth and foliar nitrogen concentration (N-mass); and (2) to assess the potential of using delta(13)C measurements, in the foliage materials collected from the clone hedges at nursery and the 4-year-old tree canopies in the field, as an indirect index of tree water use efficiency for selecting elite F-1 hybrid pine clones with improved tree growth. There were significant differences in foliar delta(13)C between the nursery hedges and the 4-year-old tree canopies in the field, between the summer and winter seasons, between the two experimental sites, and between the upper outer and lower outer canopy positions sampled. This indicates that delta(13)C measurements in the foliage materials are significantly influenced by the sampling techniques and environmental conditions. Significant differences in foliar delta(13)C, at the upper outer canopy in both field experiments in summer and winter, were detected between the clones, and between the female parents of the clones. Clone means of tree height at age ca. 3 years were positively related to those of the upper outer canopy delta(13)C at both experimental sites in winter, but only for the wetter site in summer. There were positive, linear relationships between clone means of canopy delta(13)C and those of canopy N-mass, indicating that canopy photosynthetic capacity might be an important factor regulating the clonal variation in canopy delta(13)C. Significant correlations were found between clone means of canopy delta(13)C at both experimental sites in summer and winter, and between those at the upper outer and lower outer canopy positions. Mean clone delta(13)C for the nursery hedges was only positively related to mean clone stem diameter at 1.3 m height at age 3 years on the wetter site. The clone by site interaction for foliar delta(13)C at the upper outer canopy was significant only in summer. Overall, the relatively high genetic variance components for foliar delta(13)C and significant, positive correlations between clone means of foliar delta(13)C and tree growth have highlighted the potential of using foliar delta(13)C measurements for assisting in selection of the elite F-1 hybrid pine clones with improved tree growth. (C) 2002 Elsevier Science B.V. All rights reserved.

Nutritional effects on neuron numbers

Undemutrition during early life is known to cause deficits and distortions of brain structure although it has remained uncertain whether or not this includes a diminution of the total numbers of neurons. Estimates of numerical density (e.g. number of cells per microscopic field, or number of cells per unit area of section, or number of cells per unit volume of tissue) are extremely difficult to interpret and do not provide estimates of total numbers of cells. However, advances in stereological techniques have made it possible to obtain unbiased estimates of total numbers of cells in well defined biological structures. These methods have been utilised in studies to determine the effects of varying periods of undernutrition during early life on the numbers of neurons in various regions of the rat brain. The regions examined so far have included the cerebellum, the dentate gyrus, the olfactory bulbs and the cerebral cortex. The only region to show, unequivocally, that a period of undernutrition during early life causes a deficit in the number of neurons was the dentate gyrus. These findings are discussed in the context of other morphological and functional deficits present in undernourished animals.

CAUSE-FIT, POSITIVE ATTITUDES AND BEHAVIORS WITHIN HYBRID COLOMBIAN ORGANIZATIONS

ABSTRACTSocially oriented ventures have provided livelihoods and social recognition to disadvantaged communities in different corners of the world. In some cases, these ventures are the result of Corporate Social Responsibility (CSR) programs. In Latin America, this type of undertaking has responded positively to unmet social needs. The social cause drives these organizations and their human resources and they give high value to organizational cause-fit. This paper presents empirical evidence of the effects of perceived cause-fit on several worker attitudes and behaviors. Psychological contract theory was adopted as theoretical background. Employees working in a hybrid (for-profit/socially oriented) Colombian organization created by a CSR program participated in the survey. Data provided by 218 employees were analyzed using PLS structural equation modeling. The results suggest the ideological components of the employee-employer relationship predict positive attitudes and cooperative organizational behaviors towards hybrid organizations.

A hybrid PSO-ANFIS approach for short-term wind power prediction in Portugal

The increased integration of wind power into the electric grid, as nowadays occurs in Portugal, poses new challenges due to its intermittency and volatility. Wind power prediction plays a key role in tackling these challenges. The contribution of this paper is to propose a new hybrid approach, combining particle swarm optimization and adaptive-network-based fuzzy inference system, for short-term wind power prediction in Portugal. Significant improvements regarding forecasting accuracy are attainable using the proposed approach, in comparison with the results obtained with five other approaches.

A hybrid approach to multi-agent decision-making

In the aftermath of a large-scale disaster, agents' decisions derive from self-interested (e.g. survival), common-good (e.g. victims' rescue) and teamwork (e.g. fire extinction) motivations. However, current decision-theoretic models are either purely individual or purely collective and find it difficult to deal with motivational attitudes; on the other hand, mental-state based models find it difficult to deal with uncertainty. We propose a hybrid, CvI-JI, approach that combines: i) collective 'versus' individual (CvI) decisions, founded on the Markov decision process (MDP) quantitative evaluation of joint-actions, and ii)joint-intentions (JI) formulation of teamwork, founded on the belief-desire-intention (BDI) architecture of general mental-state based reasoning. The CvI-JI evaluation explores the performance's improvement

Short-term electricity prices forecasting in a competitive market by a hybrid PSO-ANFIS approach

In this paper, a novel hybrid approach is proposed for electricity prices forecasting in a competitive market, considering a time horizon of 1 week. The proposed approach is based on the combination of particle swarm optimization and adaptive-network based fuzzy inference system. Results from a case study based on the electricity market of mainland Spain are presented. A thorough comparison is carried out, taking into account the results of previous publications, to demonstrate its effectiveness regarding forecasting accuracy and computation time. Finally, conclusions are duly drawn. (C) 2012 Elsevier Ltd. All rights reserved.