SUPERCONDUCTING YBA2CU3O7 THIN-FILMS ON MGO BY KRF LASER ABLATION - OPTIMIZATION OF DEPOSITION PARAMETERS

The optimization of interrelated deposition parameters during deposition of in situ YBa2Cu3O7 thin films on MgO substrates by KrF laser ablation was systematically studied in a single experimental chamber. The optimum condition was found to be a substrate temperature of 720-degrees-C and a target-substrate distance of 5 cm in an oxygen partial pressure of 100 mTorr. These conditions produced films with T(c) = 87 K. The presence of YO in the plasma plume was found to be important in producing good quality films. The films were characterized by resistance-temperature measurements, energy dispersive x-ray analyses, scanning electron microscopy, and x-ray-diffraction measurements, and the physical reasons underlying film quality degradation at parameter values away from optimal are discussed.

Potassium-doped Ni-MgO-ZrO catalysts for dry reforming of methane to synthesis gas

Ni/K-MgO-ZrO catalysts for dry reforming of methane, with a range of Mg/Zr ratios and each containing about 10 wt% Ni, were prepared via Ni nitrate impregnation on MgO-ZrO supports synthesized by co-precipitation using KCO. It was found that a proportion of the potassium of the precipitant remained in the samples and improved the stability of the catalysts in the reaction. It was also shown that reduction of the catalysts at 1,023 K without calcination in air is necessary for stable and high activity; calcination in air at 1,073 K gives a deterioration of the catalytic properties, leading to rapid deactivation during the reaction. The order of the CH conversions of the reduced catalysts after 14 h on stream was as follows: Ni/K-MgZr ~ Ni/K-Mg ≥ Ni/K-MgZr Ni/K-Zr. A catalyst with 0.95 wt% K on MgO-ZrO with a Mg:Zr mole ratio of 5:2 showed the best resistance to deactivation. Experiments in a microbalance system showed that there was only negligible coke deposition on the surface of this sample. This behaviour was attributed to the presence of Ni nanoparticles with a diameter of less than 10 nm located on a MgO/NiO solid solution shell doped by K ions; this in turn covers a core of tetragonal ZrO and/or a MgO/ZrO solid solution. This conclusion was supported by EDS/TEM, XPS, XRD and H chemisorption measurements. © 2013 Springer Science+Business Media New York.

Fusión de magnesia (MgO) en horno de arco eléctrico y su caracterización para la industria refractaria [por] Guadalupe Alan Castillo Rodríguez

Tesis (Maestría en Ciencias de Ingeniería Mecánica, con especialidad en Materiales

Cambios físico-químicos de un refractario MgO-C después de servicio en horno de arco eléctrico

Tesis (Maestría en Ciencias de la Ingeniería Mecánica, con especialidad en Materiales) - U.A.N.L, 1992

Obtención de circonia estabilizada con MgO (por) Ana María Arato Tovar

Tesis (Maestría en Ciencias de la Ingeniería Mecánica, con Especialidad en Matriales) U.A.N.L.

Modelo térmico de la fusión de MgO en un horno de arco eléctrico [por] Carlos Evaristo Esparza Garcés

Tesis (Maestría en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) U.A.N.L.

Investigación sobre el efecto de la Hercynita en la microestructura y propiedades de una combinación refractaria base MGO-CaZrO3

Tesis ( Maestro en Ciencias en Ingeniería de Materiales) U.A.N.L.

Nuevo desarrollo de materiales a base de MgO-Espinel (MgO.Al2O3) - carbón por Oscar Díaz Toledo

Tesis (Doctor en Ing. de Materiales) U.A.N.L.

Optimización del proceso de fusión de magnesia (MgO) por horno de arco eléctrico mediante la validación de un modelo matemático [por] Guadalupe Alan Castillo Rodríguez

Tesis (Doctorado en Ingeniería de Materiales) U.A.N.L.

Influencia del hierro en la estructura del espinel en el sistema MgO-Al2O3-Fe2O3 sinterizado en horno convencional y mediante microondas

Tesis (Doctor en Ciencias de la Ingeniería de Materiales) UANL, 2001.

Desarrollo de una tecnología refractaria basada en MgO-CaZrO? reforzado con hercinita para hornos rotatorios de cemento.

Tesis (Doctor en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) UANL, 2009.

The effect of dopants on the microwave dielectric properties of Ba( Mgo.33Ta0.67)03 ceramics

The effect of dopants with different valencies and ionic radii on the densification, structural ordering, and microwave dielectric properties of Ba(Mg1t3Tazt3)O3 (BMT) is investigated. It is found that dopants such as Sb,05, MnO, ZrO,, WO1, and ZnO improve the microwave dielectric properties of BMT. Addition of trivalent dopants is detrimental to the cation ordering and dielectric properties of BMT. A correlation between the microwave dielectric properties of BMT and ionic radii of the dopant has been established. The variation of the dielectric properties of pure and doped BMT at cryogenic temperatures is also discussed

Coverage effects on the magnetism of Fe/MgO(001) ultrathin films

Different aspects of the structure-magnetism and morphology-magnetism correlation in the ultrathin limit are studied in epitaxial Fe films grown on MgO(001). In the initial stages of growth the presence of substrate steps, intrinsically higher than an Fe atomic layer, prevent the connection between Fe islands and hence the formation of large volume magnetic regions. This is proposed as an explanation to the superparamagnetic nature of ultrathin Fe films grown on MgO in addition to the usually considered islanded, or Vollmer-Weber, growth. Using this model, we explain the observed transition from superparamagnetism to ferromagnetism for Fe coverages above 3 monolayers (ML). However, even though ferromagnetism and magnetocrystalline anisotropy are observed for 4 ML, complete coverage of the MgO substrate by the Fe ultrathin films only occurs around 6 ML as determined by polar Kerr spectra and simulations that consider different coverage situations. In annealed 3.5 ML Fe films, shape or configurational anisotropy dominates the intrinsic magnetocrystalline anisotropy, due to an annealing induced continuous to islanded morphological transition. A small interface anisotropy in thicker films is observed, probably due to dislocations observed at the Fe¿MgO(001) interface.