Planform structure of turbulent free convection on horizontal surfaces

The planform structure of turbulent free convection over a heated horizontal surface has been visualized and analyzed for different boundary conditions at the top and for different aspect ratios, for flux Rayleigh numbers ranging from 10 exp 8 - 10 exp 10. The different boundary conditions correspond to Rayleigh-Benard convection, open convection with evaporation at the top and with an imposed external flow on the heated boundary. Without the external flow the planform is one randomly oriented line plume. At large Ra, these line plumes seem to align along the diagonal, persumably due to a large-scale flow along as visualized in the side view. When the external flow is imposed, the line plumes clearly align in the direction of external flow. Flow visualization reveals that at these Ra, the shear tends to break the plumes which otherwise would reach the opposite boundary. (Author)

Plumes Dynamics and Heat Transfer over Horizontal Grooved Surfaces

This study investigates the free convection and plumes dynamics over horizontal surfaces with parallel V-grooves. The convection is studied in a tank of water with the bottom surface being a smooth or grooved surface and the top of the water surface exposed to ambient. Two groove heights were used-10 mm and 3 mm-and the experiment was done with two values of aspect ratio-2.9 and 1.8 (aspect ratio is the width of the fluid layer/height of fluid layer). Heat flux at the bottom surface was from electrical heating. Beyond a certain critical temperature difference, enhanced heat transfer is obtained on the grooved surface compared to a smooth surface. Nusselt numbers are evaluated for both smooth and grooved surfaces and correlated using modified Rayleigh numbers. Visualization shows that the enhanced heat transport in the rough cavities cannot be ascribed to the increase in the contact area; rather, it must be the local dynamics of the thermal boundary layer.

Two-dimensional moist stratified turbulence and the emergence of vertically sheared horizontal flows

Moist stratified turbulence is studied in a two-dimensional Boussinesq system influenced by condensation and evaporation. The problem is set in a periodic domain and employs simple evaporation and condensation schemes, wherein both the processes push parcels towards saturation. Numerical simulations demonstrate the emergence of a moist turbulent state consisting of ordered structures with a clear power-law type spectral scaling from initially spatially uncorrelated conditions. An asymptotic analysis in the limit of rapid condensation and strong stratification shows that, for initial conditions with enough water substance to saturate the domain, the equations support a straightforward state of moist balance characterized by a hydrostatic, saturated, vertically sheared horizontal flow (VSHF). For such initial conditions, by means of long time numerical simulations, the emergence of moist balance is verified. Specifically, starting from uncorrelated data, subsequent to the development of a moist turbulent state, the system experiences a rather abrupt transition to a regime which is close to saturation and dominated by a strong VSHF. On the other hand, initial conditions which do not have enough water substance to saturate the domain, do not attain moist balance. Rather, the system is observed to remain in a turbulent state and oscillates about moist balance. Even though balance is not achieved with these general initial conditions, the time scale of oscillation about moist balance is much larger than the imposed time scale of condensation and evaporation, thus indicating a distinct dominant slow component in the moist stratified two-dimensional turbulent system. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.3694805]

Flow visualization in turbulent free convection over horizontal smooth and grooved surfaces

The present paper discusses the flow visualization for turbulent free convection in a tank of water with the bottom surface being a smooth or a grooved surface and the top of the water surface exposed to ambient. The grooved surface is of parallel 90 degrees V-grooves with groove height of 10 mm and groove width of 20 mm. The experiment is carried out with aspect ratio (AR) of 2.9 and Rayleigh number (Ra) in the range, 1.3 x 10(7) - 4 x 10(7). Here AR is the aspect ratio (= width of fluid layer/height of fluid layer). Heat flux at the bottom surface is from electrical heating. From the pH-dye visualization, interesting flow structures are observed and these structures are analyzed with the help of plumes dynamics and temperature variations with time. (C) 2011 Elsevier Ltd. All rights reserved.

Horizontal pullout capacity of a group of two vertical plate anchors in clay

The horizontal pullout capacity of a group of two vertical strip plate anchors, placed along the same vertical plane, in a fully cohesive soil has been computed by using the lower bound finite element limit analysis. The effect of spacing between the plate anchors on the magnitude of total group failure load (P-uT) has been evaluated. An increase of soil cohesion with depth has also been incorporated in the analysis. For a weightless medium, the total pullout resistance of the group becomes maximum corresponding to a certain optimum spacing between the anchor plates which has been found to vary generally between 0.5B and B; where B is the width of the anchor plate. As compared to a single plate anchor, the increase in the pullout resistance for a group of two anchors becomes greater at a higher embedment ratio. The effect of soil unit weight has also been analyzed. It is noted that the interference effect on the pullout resistance increases further with an increase in the unit weight of soil mass.

Horizontal pullout resistance of a group of two vertical anchors in sand

The horizontal pullout capacity of a group of two vertical strip anchors placed along the same vertical plane in sand has been determined by using the upper bound finite elements limit analysis. The variation of the efficiency factor (xi (gamma) ) with changes in clear spacing (S) between the anchors has been established to evaluate the total group failure load for different values of (i) embedment ratio (H/B), (ii) soil internal friction angle (phi), and (iii) anchor-soil interface friction angle (delta). The total group failure load, for a given H/B, becomes always maximum corresponding to a certain optimal spacing (S-opt). The value of S-opt/B was found to lie in a range of 0.5-1.4. The maximum magnitude of xi (gamma) increases generally with increases in H/B, phi and delta.

Vertical uplift resistance of two closely spaced horizontal strip anchors embedded in cohesive-frictional weightless medium

The vertical uplift resistance of two closely spaced horizontal strip plate anchors has been investigated by using lower and upper bound theorems of the limit analysis in combination with finite elements and linear optimization. The interference effect on uplift resistance of the two anchors is evaluated in terms of a nondimensional efficiency factor (eta(c)). The variation of eta(c) with changes in the clear spacing (S) between the two anchors has been established for different combinations of embedment ratio (H/B) and angle of internal friction of the soil (phi). An interference of the anchors leads to a continuous reduction in uplift resistance with a decrease in spacing between the anchors. The uplift resistance becomes a minimum when the two anchors are placed next to each other without any gap. The critical spacing (S-cr) between the two anchors required to eliminate the interference effect increases with an increase in the values of both H/B and phi. The value of S-cr was found to lie approximately in the range 0.65B-1.5B with H/B = 1 and 11B-14B with H/B = 7 for phi varying from 0 degrees to 30 degrees.

Vertical uplift resistance of two horizontal strip anchors with common vertical axis

With an application of the upper bound finite element limit analysis, the vertical pullout capacity of a group of two horizontal strip plate anchors, with the common vertical axis and placed in a cohesive-frictional soil, has been computed. The variation of the uplift factors Fc, Fq and Fy, due to the contributions of soil cohesion, surcharge pressure and unit weight, respectively, has been evaluated for different combinations of S/B and H/B. As compared to single isolated anchor, the group of two anchors generates significantly greater magnitude of Fc for Φ ≤ 20° especially with greater values of H/B and under fully bonded anchor-soil interface condition. The factor Fc attains almost the maximum value when the upper anchor plate is placed midway between ground surface and the lower anchor plate. The factors Fq and Fy, on the other hand, for a group of two anchors are found to remain almost equal to that of a single isolated anchor as long as the levels of the lower plate in the group and the single isolated anchor are kept the same.

Three-Dimensional Study of Natural Convection in a Horizontal Channel With Discrete Heaters on One of Its Vertical Walls

Three-dimensional natural convection in a horizontal channel with an array of discrete flush-mounted heaters on one of its vertical walls is numerically studied. Effects of thermal conductivities of substrate and heaters and convection on outer sides of the channel walls on heat transfer are examined. The substrate affects heat transfer in a wider range of thermal conductivities than do the heaters. At lower heater thermal conductivities a higher heat portion is transferred by direct convection from the heaters to the adjacent coolant. However, higher substrate conductivity is associated with higher heat portion transferred through the substrate. The innermost heater column is found to become the hottest heater column due to the lower coolant accessibility. The heat transfer in the channel is strongly influenced by convection on the outer sides of the channel walls. Correlations are presented for dimensionless temperature maximum and average Nusselt number.

Vertical Uplift Resistance of Two Interfering Horizontal Anchors in Clay

The vertical uplift resistance of two interfering rigid strip plate anchors embedded horizontally at the same level in clay has been examined. The lower and upper bound theorems of the limit analysis in combination with finite-elements and linear optimization have been employed to compute the failure load in a bound form. The analysis is meant for an undrained condition and it incorporates the increase of cohesion with depth. For different clear spacing (S) between the anchors, the magnitude of the efficiency factor (eta c gamma) resulting from the combined components of soil cohesion (c) and soil unit weight (gamma), has been computed for different values of embedment ratio (H/B), the rate of linear increase of cohesion with depth (m) and normalized unit weight (gamma H/c). The magnitude of eta c gamma has been found to reduce continuously with a decrease in the spacing between the anchors, and the uplift resistance becomes minimum for S/B=0. It has been noted that the critical spacing between the anchors required to eliminate the interference effect increases continuously with (1) an increase in H/B, and (2) a decrease in m.

Estimates of site response based on spectral ratio between horizontal and vertical components of ambient vibrations in the source zone of 2001 Bhuj earthquake

We investigated the site response characteristics of Kachchh rift basin over the meizoseismal area of the 2001, Mw 7.6, Bhuj (NW India) earthquake using the spectral ratio of the horizontal and vertical components of ambient vibrations. Using the available knowledge on the regional geology of Kachchh and well documented ground responses from the earthquake, we evaluated the H/V curves pattern across sediment filled valleys and uplifted areas generally characterized by weathered sandstones. Although our HIV curves showed a largely fuzzy nature, we found that the hierarchical clustering method was useful for comparing large numbers of response curves and identifying the areas with similar responses. Broad and plateau shaped peaks of a cluster of curves within the valley region suggests the possibility of basin effects within valley. Fundamental resonance frequencies (f(0)) are found in the narrow range of 0.1-2.3 Hz and their spatial distribution demarcated the uplifted regions from the valleys. In contrary, low HIV peak amplitudes (A(0) = 2-4) were observed on the uplifted areas and varying values (2-9) were found within valleys. Compared to the amplification factors, the liquefaction indices (kg) were able to effectively indicate the areas which experienced severe liquefaction. The amplification ranges obtained in the current study were found to be comparable to those obtained from earthquake data for a limited number of seismic stations located on uplifted areas; however the values on the valley region may not reflect their true amplification potential due to basin effects. Our study highlights the practical usefulness as well as limitations of the HIV method to study complex geological settings as Kachchh. (C) 2014 Elsevier Ltd. All rights reserved.

Application of Electrical Resistance Tomography System to Monitor Gas/Liquid Two-Phase Flow in a Horizontal Pipe

The Electrical Resistance Tomography (ERT) technique possesses great potential in monitoring widely exiting industrial two/multi-phase flow. For vertical pipe flow and inclined pipe flow, some application studies with exciting results have been reported, but there is rarely a paper regarding the application of ERT to horizontal gas/liquid pipe flow. This paper addresses this issue and proposes a smart method, Liquid Level Detection method, to conventional ERT system. The enhanced ERT system using the new method can monitor horizontal pipe flow effectively and its application is no longer restricted by the flow conditions. Some experimental results from monitoring an air/water slug pipe flow are presented.

Experimental Study of Pore Pressure and Deformation of Suction Bucket Foundations Under Horizontal Dynamic Loading

Centrifuge experiments are carried out to investigate the responses of suction bucket foundations under horizontal dynamic loading. The effects of loading amplitude, the size of the bucket and the structural weight on the dynamic responses are investigated. It is shown that, when the loading amplitude is over a critical value, the sand at the upper part around the bucket softens or even liquefies. The liquefactio...

The Response of Bucket Foundation under Horizontal Dynamic Loading

The experimental investigation of the response of suction bucket foundation in fine sand layer under horizontal dynamic loading has been carried out. The developments of settlement and excess pore pressure of sand foundation have been mainly studied. It is shown that the sand surrounding the bucket softens or even liquefies at the first stage if the loading amplitude is over a critical value, at later stage, the bucket settles and the sand layer consolidates gradually. With the solidification of the liquefied sand layer and the settlement of the bucket, the movement of the sand layer and the bucket reach a stable state.

Efecto de la dosis y el momento de aplicación de nitrógeno sobre la producción y calidad de semilla de pasto Gamba (Andropogon gayanus Kunth CIAT 621)

En el centro experimental ele pastos y forrajes "Santa Rosa", de la Comisión Nacional de Ganadería, ubicada al Norte de la comunidad de Sabana Grande, municipio de Managua, se realizó el ensayo acerca de los efectos de diferentes dosis y momentos de aplicación de nitrógeno, sobre la producción y calidad de semillas de A. gavanus Kunth CIAT 621. Se utilizó un diseño experimental de parcelas divididas con bloques completamente al azar con arreglo bifactorial. Se probaron cuatro dosis de fertilizante nitrogenado (urea al 46%): 50, 75, 100 y 125 kg/N/ha/corte, y un testigo (sin fertilizar), además de tres momentos de aplicación del fertilizante (al momento del corte, 15 y 30 días después del corte de uniformidad) Los resultados demostraron que tanto las dosis como los momentos tuvieron efectos estadísticamente significativos (P<0.01), sobre los componentes estructurales del rendimiento: tamaño de inflorescencia y número de tallos reproductivos por hectárea. Otros como: tamaño del raquis, número de raquis y número de ramificaciones, no mostraron diferencia significativa para dosis, ni para momentos de aplicación. Además, las dos is de nitrógeno influyeron más sobre el rendimiento de semilla, que los momentos de aplicación. La prueba de proporciones "Z", fue el estadístico de prueba utilizado, para analizar la calidad de la semilla, por la diferencia de proporciones entre las medias comparadas de los tratamientos. La variable de calidad de semilla pura, reflejó su mayor valor con el momento de aplicación 30 días después del corte de uniformidad (57.18 %), presentando únicamente diferencia significativa (P<0.05), con la aplicación de nitrógeno al momento del corte de uniformidad; respecto a las dosis aplicadas el máximo valor le correspondió a los 100 kg/N/ha/corte con 57.9 %, mostrando diferencia significativa (P<0.05), solamente con la dosis de 125 kg/N/ha/corte. El porcentaje de germinación fue más alto para el tratamiento de aplicación del nitrógeno a los 30 días después del corte de uniformidad con 48.7 %, teniendo únicamente diferencia significativa (P<0.05), con la aplicación al momento del corte de uniformidad; sin embargo, la mayor germinación se registró con la dosis de 100 kg/N/ha/corte (49.5 %). mostrando solamente diferencias significativas (P<0.05), con la dosis de 125 kg/N/ha/corte. El valor cultural, mostró una tendencia igual a las dos variables de calidad anteriores, por factores separados (dosis y momentos). El mayor valor obtenido fue con la dosis ele 100 kg/N/ha/corte(28.67 %), siendo estadísticamente igual (P>0.05), con las dosis de 50, 75 kg/N/ha/corte y el testigo; únicamente resultó diferencias significativas (P<0.05), con la dosis de 125 kg/N/ha/corte. Además, el momento a los 30 días después del corte de uniformidad (27.99 %), fue diferente estadísticamente (P<0.05), a la aplicación de nitrógeno al momento del corte de uniformidad. Este resultado se debió a que el valor cultural es un índice compuesto, producto de ambas variables (%de semilla pura y % de germinación). Por otra parte, el valor cultural mostró que al interactuar ambos factores (momento y dosis), se registró un alto valor de pureza y germinación con respecto al obtenido por efecto de factores separados; el mayor valor obtenido fue con el momento de aplicación a los 30 días después del corte de uniformidad y la dosis de 50 kg/N/ha/corte (34.2 % de semilla pura y germinable).