Food structure : its formation and relationships with other properties

Food materials are complex in nature as it has heterogeneous, amorphous, hygroscopic and porous properties. During processing, microstructure of food materials changes which significantly affects other properties of food. An appropriate understanding of the microstructure of the raw food material and its evolution during processing is critical in order to understand and accurately describe dehydration processes and quality anticipation. This review critically assesses the factors that influence the modification of microstructure in the course of drying of fruits and vegetables. The effect of simultaneous heat and mass transfer on microstructure in various drying methods is investigated. Effects of changes in microstructure on other functional properties of dried foods are discussed. After an extensive review of the literature, it is found that development of food structure significantly depends on fresh food properties and process parameters. Also, modification of microstructure influences the other properties of final product. An enhanced understanding of the relationships between food microstructure, drying process parameters and final product quality will facilitate the energy efficient optimum design of the food processor in order to achieve high-quality food

Evaluation of electrocoagulation for the pre-treatment of coal seam water

This work explored the applicability of electrocoagulation (EC) using aluminium electrodes for the removal of contaminants which can scale and foul reverse osmosis membranes from a coal seam (CS) water sample, predominantly comprising sodium chloride, and sodium bicarbonate. In general, the removal efficiency of species responsible for scaling and fouling was enhanced by increasing the applied current density/voltage and contact times (30–60 s) in the EC chamber. High removal efficiencies of species potentially responsible for scale formation in reverse osmosis units such as calcium (100%), magnesium (87.9%), strontium (99.3%), barium (100%) and silicates (98.3%) were achieved. Boron was more difficult to eliminate (13.3%) and this was postulated to be due to the elevated solution pH. Similarly, fluoride removal from solution (44%) was also inhibited by the presence of hydroxide ions in the pH range 9–10. Analysis of produced flocs suggested the dominant presence of relatively amorphous boehmite (AlOOH), albeit the formation of Al(OH)3 was not ruled out as the drying process employed may have converted aluminium hydroxide to aluminium oxyhydroxide species. Evidence for adsorption of contaminants on floc surface sites was determined from FTIR studies. The quantity of aluminium released during the electrocoagulation process was higher than the Faradaic amount which suggested that the high salt concentrations in the coal seam water had chemically reacted with the aluminium electrodes.

Modelling of the evaporation of a droplet suspended in a binary atmosphere

The process of spray drying is applied in a number of contexts. One such application is the production of a synthetic rock used for storage of nuclear waste. To establish a framework for a model of the spray drying process for this application, we here develop a model describing evaporation from droplets of pure water, such that the model may be extended to account for the presence of colloid within the droplet. We develop a spherically-symmetric model and formulate continuum equations describing mass, momentum, and energy balance in both the liquid and gas phases from first principles. We establish appropriate boundary conditions at the surface of the droplet, including a generalised Clapeyron equation that accurately describes the temperature at the surface of the droplet. To account for experiment design, we introduce a simplified platinum ball and wire model into the system using a thin wire problem. The resulting system of equations is transformed in order to simplify a finite volume solution scheme. The results from numerical simulation are compared with data collected for validation, and the sensitivity of the model to variations in key parameters, and to the use of Clausius–Clapeyron and generalised Clapeyron equations, is investigated. Good agreement is found between the model and experimental data, despite the simplicity of the platinum phase model.

Experimental study on shrinkage behaviour and prediction of shrinkage magnitudes of residual soils

The present study examines the shrinkage behaviour of residually derived black cotton (BC) soil and red soil compacted specimens that were subjected to air-drying from the swollen state. The soil specimens were compacted at varying dry density and moisture contents to simulate varied field conditions. The void ratio and moisture content of the swollen specimens were monitored during the drying process and relationship between them is analyzed. Shrinkage is represented as reduction in void ratio with decrease in water content of soil specimens. It is found to occur in three distinct stages. Total shrinkage magnitude depends on the type of clay mineral present. Variation in compaction conditions effect marginally total shrinkage magnitudes of BC soil specimens but have relatively more effect on red soil specimens. A linear relation is obtained between total shrinkage magnitude and volumetric water content of soil specimens in swollen state and can be used to predict the shrinkage magnitude of soils.

Evolution of vertical phase separation in P3HT:PCBM thin films induced by thermal annealing

The achievement of the desirable morphology at the nanometer scale of bulk heterojunctions consisting of a conjugated polymer with fullerene derivatives is a prerequisite in order to optimize the power conversion efficiency of organic solar cells. The various experimental conditions such as the choice of solvent, drying rates and annealing have been found to significantly affect the blend morphology and the final performance of the photovoltaic device. In this work, we focus on the effects of post deposition thermal annealing at 140 °C on the blend morphology, the optical and structural properties of bulk heterojunctions that consist of poly(3-hexylthiophene) (P3HT) and a methanofullerene derivative (PCBM). The post thermal annealing modifies the distribution of the P3HT and the PCBM inside the blend films, as it has been found by Spectroscopic Ellipsometry studies in the visible to far-ultraviolet spectral range. Phase separation was identified by AFM and GIXRD as a result of a slow drying process which took place after the spin coating process. The increase of the annealing time resulted to a significant increase of the P3HT crystallinity at the top regions of the blend films. © 2011 Elsevier B.V. All rights reserved.

The influence of diets containing dried bivalve feces and/or powdered algae on growth and energy distribution in sea cucumber Apostichopus japonicus (Selenka) (Echinodermata : Holothuroidea)

In recent years, bivalve feces and powdered algae have been used as the food sources of holothurians in China. In this study, growth and energy budget for sea cucumber Apostichopus japonicus (Selenka) with initial wet body,veights of 32.5 1.0 g (mean +/- SE, n=45) when fed with five different granule diets containing dried bivalve feces and/or powdered algae in water temperature 13.2-19.8 degrees C and salinity 30-32ppt were quantified in order to investigate how diets influence growth and energy distribution and to find out the proper diet for land-based intensive culture of this species. Results showed that diets affected the food ingestion, feces production, food conversion efficiency and apparent digestive ratios, hence the growth and energy budget. Sea cucumbers fed with dried feces of bivalve showed poorer energy absorption, assimilation and growth than individuals fed with other four diets; this could be because feces-drying process removed much of the benefits. Dried bivalve feces alone, therefore, were not a suitable diet for sea cucumbers in intensive cultivation. The mixed diets of feces and powered algae showed promising results for cultivation of sub-adult Apostichopus japonicus, while animals fed with powdered algae alone, could not obtain the best growth. According to SGR of tested animals, a formula of 75% feces and 25% powdered algae is the best diet for culture of this species. Extruded diets were used in the present experiment to overcome shortcomings of the traditional powdered feeds, however, it seems a conflict exists between drying bivalve feces to form extruded diets and feeding sea cucumbers with fresh feces which contain beneficial bacteria. Compared with other echinoderms, in holothurians the energy deposited in growth is lower and the energy loss in feces accounts for the majority of the ingested energy. Such detailed information could be helpful in further development of more appropriate diets for culture of holothurians. (c) 2006 Elsevier B.V. All rights reserved.

Hydrogen permeation and corrosion behaviour of high strength steel 35CrMo under cyclic wet-dry conditions

Hydrogen permeation behaviours of high strength steel 35CrMo under different cyclic wet-dry conditions have been investigated by using Devanathan-Stachurski's technique. Four electrolytes were used: distilled water, seawater, seawater containing 1500 ppm H2S and seawater containing 0.03 mol L-1 SO2. The corrosion weight loss of 35CrMo in the wet-dry cycles was measured simultaneously. The experimental results show that hydrogen can be detected at the surface opposite to the corroding side of the specimen during wet-dry cycles and the permeation current density during a wet-dry cycle showed a maximum during the drying process. The hydrogen permeation was obviously promoted by Cl- ions, H2S and SO2. The hydrogen permeation in the real marine atmosphere has also been investigated. There is a clear correlation between the amount of hydrogen permeated and the corrosion weight losses. Results show the importance of hydrogen permeation that merits further investigation.

元谋地区晚新生代河湖相沉积物磁性地层学及古环境研究

Yuanmou area lies on the southeastern edge of the Tibetan Plateau, the middlesegment of Yunnan-Sichuan North-South Extending Tectonic Belt and the upper reaches of the Yangztze River, which is renowned for its thick late Cenozoic fluvial-lacustrine sequences that yield rich mammalian fossils including hominoid and early human. The sediments provides great potentials for understanding the relationships between uplift of the Tibetan Plateau, evolution of hominoids and other mammalian and evolution and formation of basins in Southwest China since late Miocene. However, lithostratigrphic and chronologic views on them are controversial and hinder further discussion of the relationships of them. To this end, we selected the Baozidongqing section and the Dapoqing section to carry out systematic lithostratigraphic, magnetostratlgraphic and environmental magnetism researches in this area.The Baozidongqing section was dated to about 10.95-7.17 Ma. The age estimation of the topmost hominoid-bearing layer was about 7.43-7.17 Ma. Rock magnetic results show that the dominant magnetic carrier is hematite, with minor amount of magnetite. Both the composition and concentration of magnetic minerals strongly correlate with the lithostratigraphy, indicating that Yuanmou basin is characterized by alternating of long-term torrid-humid climate and short-term dry-hot climate. But the pattern of these short-term hot-dry events, including both the lasting time and the frequency of their occurrence dramatically changed since -8.1 Ma. Our results infer that the drying process of the Asian west interior and a significant uplift of the Tibetan Plateau would have probably caused jointly the extinction of hominoids, or the emigration of hominoids from Yuanmou to adjacent relatively torrid-humid areas.The strata between the upper of the Dapoqing section, the Niujianbao Hill and Shangnabang area can be linked by three mark layers of conglomerate, which is rather continuous and coherent than physical disturbance by new tectonic activities. Rock magnetic studies indicate that hematite is the main magnetic carriers. The section is dated back to about 2.8-1.37 Ma. Its paleocurrent flowed northeastward, which was a close and stagnant river and swamp environment about 2.2 Ma ago. Then it ran northwestward and turned into an open overflown and braid river sedimentary face during 2.2 to 1.57 Ma. Since 1.57 Ma, the paleocurrent flowed intensely northwestern and about 1.37 Ma ago, it ended the basically continuous fluvial-lacustrine deposition.

A novel method to synthesize amorphous silica-alumina materials with mesoporous distribution without using templates and pore-regulating agents

In this study, a novel sol-gel method is used to synthesize amorphous silica-alumina materials with a narrow mesoporous distribution and various Si/Al molar ratios without using any templates and pore-regulating agents. During the preparation procedure, only inexpensive inorganic salts were used as raw materials, instead of expensive and harmful alkoxides. The precursor sol was dried at room temperature in a vacuum box kept at 60 mmHg until it began to form the gel. The results of a nitrogen sorption experiment indicate that the synthesized materials with different Si/Al molar ratios have similar mesoporous distributions (within 2-12 nm). Moreover, it was found that the material's pore size distribution remains at a similar value during the heat treatment from room temperature to 550 degreesC. On the basis of the nitrogen sorption, TEM, and AFM characterization results, a formation mechanism of mesopores which accounts for the experimental data is also suggested. This suggested mechanism involves rearrangement of the primary particles during the drying process to form the precursors of the similarly sized mesopores. The synthesized materials were characterized by XRD, thermal analysis (TG/DTA), Al-27 and Si-29 MAS NMR spectroscopy, SEM, TEM, and AFM. The results of Al-27 and 29Si MAS NMR indicate that the distribution of silicon and aluminum in the synthesized materials is more uniform and homogeneous than that in the mixed oxides prepared via the traditional sol-gel method even at high alumina contents. The type and density of the acid sites were studied using pyridine adsorption-desorption FTIR spectroscopy. It was shown that the acidity of the synthesized materials is higher than that of the silica-alumina materials prepared by conventional methods.

Experimental quantification and modelling of attrition of infant formulae during pneumatic conveying

Infant formula is often produced as an agglomerated powder using a spray drying process. Pneumatic conveying is commonly used for transporting this product within a manufacturing plant. The transient mechanical loads imposed by this process cause some of the agglomerates to disintegrate, which has implications for key quality characteristics of the formula including bulk density and wettability. This thesis used both experimental and modelling approaches to investigate this breakage during conveying. One set of conveying trials had the objective of establishing relationships between the geometry and operating conditions of the conveying system and the resulting changes in bulk properties of the infant formula upon conveying. A modular stainless steel pneumatic conveying rig was constructed for these trials. The mode of conveying and air velocity had a statistically-significant effect on bulk density at a 95% level, while mode of conveying was the only factor which significantly influenced D[4,3] or wettability. A separate set of conveying experiments investigated the effect of infant formula composition, rather than the pneumatic conveying parameters, and also assessed the relationships between the mechanical responses of individual agglomerates of four infant formulae and their compositions. The bulk densities before conveying, and the forces and strains at failure of individual agglomerates, were related to the protein content. The force at failure and stiffness of individual agglomerates were strongly correlated, and generally increased with increasing protein to fat ratio while the strain at failure decreased. Two models of breakage were developed at different scales; the first was a detailed discrete element model of a single agglomerate. This was calibrated using a novel approach based on Taguchi methods which was shown to have considerable advantages over basic parameter studies which are widely used. The data obtained using this model compared well to experimental results for quasi-static uniaxial compression of individual agglomerates. The model also gave adequate results for dynamic loading simulations. A probabilistic model of pneumatic conveying was also developed; this was suitable for predicting breakage in large populations of agglomerates and was highly versatile: parts of the model could easily be substituted by the researcher according to their specific requirements.

Fabrication and Repair of Cartilage Defects with a Novel Acellular Cartilage Matrix Scaffold

The objectives of this study were to develop a three-dimensional acellular cartilage matrix (ACM) and investigate its possibility for use as a scaffold in cartilage tissue engineering. Bovine articular cartilage was decellularized sequentially with trypsin, nuclease solution, hypotonic buffer, and Triton x 100 solution; molded with freeze-drying process; and cross-linked by ultraviolet irradiation. Histological and biochemical analysis showed that the ACM was devoid of cells and still maintained the collagen and glycosaminoglycan components of cartilage. Scanning electronic microscopy and mercury intrusion porosimetry showed that the ACM had a sponge-like structure of high porosity. The ACM scaffold had good biocompatibility with cultured rabbit bone marrow mesenchymal stem cells with no indication of cytotoxicity both in contact and in extraction assays. The cartilage defects repair in rabbit knees with the mesenchymal stem cell-ACM constructs had a significant improvement of histological scores when compared to the control groups at 6 and 12 weeks. In summary, the ACM possessed the characteristics that afford it as a potential scaffold for cartilage tissue engineering.

Investigation Into The Effect of Varying L-leucine Concentration on the product characteristics of Spray-dried Liposome Powders

Spray-dried formulations offer an attractive delivery system for administration of drug encapsulated into liposomes to the lung, but can suffer from low encapsulation efficiency and poor aerodynamic properties. In this paper the effect of the concentration of the anti-adherent l-leucine was investigated in tandem with the protectants sucrose and trehalose. Two manufacturing methods were compared in terms of their ability to offer small liposomal size, low polydispersity and high encapsulation of the drug indometacin. Unexpectedly sucrose offered the best protection to the liposomes during the spray drying process, although formulations containing trehalose formed products with the best powder characteristics for pulmonary delivery; high glass transition values, fine powder fraction and yield. It was also found that l-leucine contributed positively to the characteristics of the powders, but that it should be used with care as above the optimum concentration of 0.5% (w/w) the size and polydispersity index increased significantly for both disaccharide formulations. The method of liposome preparation had no effect on the stability or encapsulation efficiency of spray-dried powders containing optimal protectant and anti-adherent. Using l-leucine at concentrations higher than the optimum level caused instability in the reconstituted liposomes.

Secagem convectiva de produtos alimentares: otimização e controlo

O presente trabalho tem como objetivo analisar a cinética de secagem do bacalhau salgado verde (Gadus morhua) em secador convectivo. É apresentada a análise da composição físico-química dos bacalhaus utilizados nos ensaios experimentais, bem como o estudo das isotermas de sorção do produto, através de experiências e modelação matemática. Dos modelos usados para o ajuste das isotermas de sorção do bacalhau salgado verde, o que melhor se adaptou aos resultados experimentais foi o modelo de GAB Modificado, com coeficientes de correlação variando entre 0,992 e 0,998. Para o controlo do processo de secagem (nomeadamente os parâmetros temperatura, humidade relativa e velocidade do ar) foi utilizada lógica difusa, através do desenvolvimento de controladores difusos para o humidificador, desumidificador, resistências de aquecimento e ventilador. A modelação do processo de secagem foi realizada através de redes neuronais artificiais (RNA), modelo semi-empírico de Page e modelo difusivo de Fick. A comparação entre dados experimentais e simulados, para cada modelo, apresentou os seguintes erros: entre 1,43 e 11,58 para o modelo de Page, 0,34 e 4,59 para o modelo de Fick e entre 1,13 e 6,99 para a RNA, com médias de 4,38, 1,67 e 2,93 respectivamente. O modelo obtido pelas redes neuronais artificiais foi submetido a um algoritmo de otimização, a fim de buscar os parâmetros ideais de secagem, de forma a minimizar o tempo do processo e maximizar a perda de água do bacalhau. Os parâmetros ótimos obtidos para o processo de secagem, após otimização realizada, para obter-se uma humidade adimensional final de 0,65 foram: tempo de 68,6h, temperatura de 21,45°C, humidade relativa de 51,6% e velocidade de 1,5m/s. Foram também determinados os custos de secagem para as diferentes condições operacionais na instalação experimental. Os consumos por hora de secagem variaram entre 1,15 kWh e 2,87kWh, com uma média de 1,94kWh.

Développement de papier bioactif par couchage à grande échelle d’enzymes immobilisées par microencapsulation

L’objectif principal de cette recherche est de contribuer au développement de biocapteurs commerciaux utilisant des surfaces de papier comme matrices d’immobilisation, capables de produire un signal colorimétrique perceptible dans les limites sensorielles humaines. Ce type de biocapteur, appelé papier bioactif, pourrait servir par exemple à la détection de substances toxiques ou d’organismes pathogènes. Pour atteindre l’objectif énoncé, ce travail propose l’utilisation de systèmes enzymatiques microencapsulés couchés sur papier. Les enzymes sont des catalyseurs biologiques dotés d’une haute sélectivité, et capables d'accélérer la vitesse de certaines réactions chimiques spécifiques jusqu’à des millions des fois. Les enzymes sont toutefois des substances très sensibles qui perdent facilement leur fonctionnalité, raison pour laquelle il faut les protéger des conditions qui peuvent les endommager. La microencapsulation est une technique qui permet de protéger les enzymes sans les isoler totalement de leur environnement. Elle consiste à emprisonner les enzymes dans une sphère poreuse de taille micrométrique, faite de polymère, qui empêche l’enzyme de s’echapper, mais qui permet la diffusion de substrats à l'intérieur. La microencapsulation utilisée est réalisée à partir d’une émulsion contenant un polymère dissous dans une phase aqueuse avec l’enzyme désirée. Un agent réticulant est ensuite ajouté pour provoquer la formation d'un réseau polymérique à la paroi des gouttelettes d'eau dans l'émulsion. Le polymère ainsi réticulé se solidifie en enfermant l’enzyme à l'intérieur de la capsule. Par la suite, les capsules enzymatiques sont utilisées pour donner au papier les propriétés de biocapteur. Afin d'immobiliser les capsules et l'enzyme sur le papier, une méthode courante dans l’industrie du papier connu sous le nom de couchage à lame est utilisée. Pour ce faire, les microcapsules sont mélangées avec une sauce de couchage qui sera appliquée sur des feuilles de papier. Les paramètres de viscosité i de la sauce et ceux du couchage ont été optimisés afin d'obtenir un couchage uniforme répondant aux normes de l'industrie. Les papiers bioactifs obtenus seront d'abord étudiés pour évaluer si les enzymes sont toujours actives après les traitements appliqués; en effet, tel que mentionné ci-dessus, les enzymes sont des substances très sensibles. Une enzyme très étudiée et qui permet une évaluation facile de son activité, connue sous le nom de laccase, a été utilisée. L'activité enzymatique de la laccase a été évaluée à l’aide des techniques analytiques existantes ou en proposant de nouvelles techniques d’analyse développées dans le laboratoire du groupe Rochefort. Les résultats obtenus démontrent la possibilité d’inclure des systèmes enzymatiques microencapsulés sur papier par couchage à lame, et ce, en utilisant des paramètres à grande échelle, c’est à dire des surfaces de papier de 0.75 x 3 m2 modifiées à des vitesses qui vont jusqu’à 800 m/min. Les biocapteurs ont retenu leur activité malgré un séchage par évaporation de l’eau à l’aide d’une lampe IR de 36 kW. La microencapsulation s’avère une technique efficace pour accroître la stabilité d’entreposage du biocapteur et sa résistance à l’exposition au NaN3, qui est un inhibiteur connu de ce biocapteur. Ce projet de recherche fait partie d'un effort national visant à développer et à mettre sur le marché des papiers bioactifs; il est soutenu par Sentinel, un réseau de recherche du CRSNG.

Einfluss der Führung des Trocknungsprozesses auf den Trocknungsverlauf und die Produkteigenschaften empfindlicher biologischer Güter

Die Konvektionstrocknung ist eine der ältesten Methoden zur Konservierung von Lebensmitteln. Es ist bekannt, dass Agrarprodukte temperaturempfindlich sind. Bei Überhitzung erleiden sie chemische und physikalische Veränderungen, die ihre Qualität vermindern. In der industriellen Praxis wird die Konvektionstrocknung in der Regel auf Grundlage empirisch ermittelter Werte durchgeführt, welche die Produkttemperatur nicht berücksichtigen. Es ist deshalb nicht sichergestellt, ob der Prozess optimal oder auch nur gut betrieben wird. Inhalt dieser Arbeit ist ein Vergleich der klassischen einstufigen Konvektionstrocknung mit einer Prozessführungsstrategie bei der die Produkttemperatur als Regelgröße eingeführt wird. Anhand der Untersuchung des Trocknungsverhaltens von Äpfeln werden die beiden Verfahren analysiert, die erhaltenen Ergebnisse miteinander verglichen und daraus optimierte Trocknungsbedingungen abgeleitet. Die für dieses Projekt entwickelte Prozessanlage erlaubt die simultane Untersuchung sämtlicher wesentlicher Temperaturen, der Gewichtsveränderung und der optischen Qualitätskriterien. Gleichzeitig ist es möglich, entweder die Lufttemperatur oder die Temperatur des Produktes zur regeln, während die jeweils andere Größe als Messwert erfasst wird. Es kann weiterhin zwischen Durch- und Überströmung gewählt werden.