Surface quality of profile extrusion dies manufactured by Selective Laser Melting

The design of plastics profile extrusion dies becomes increasingly more complex so that conventional manufacture processes reach their limit in the die manufacture. A feasible manufacture of arbitrarily designed dies is only possible by additive manufacturing. An especially promising process is hereby the Selective Laser Melting with which metal parts with series identical mechanical properties can be produced without the need for part specific tooling or downstream sintering processes. Disadvantegeous is, however, the relatively rough surface of additively manufactured parts. Against this background, the manufacturing of an profile extrusion die by Selective Laser Melting and the plastics profile surface quality, that can be achieved with such dies, is investigated. For this purpose, profiles are extruded both with an additively manufactured die and a conventionally milled sample of the same die geometry. In case of the additively manufactured die a concept for the surface finishing of the flow channel is required, which can be applied to arbitrarily shaped geometries. Therefore, two different reworking processes are applied only to the die land of the flow channel. The comparison of the surface roughnesses shows that the additively manufactured die with a polished die land delivers the same surface quality as the conventional die.

Novel free-form optical surface design with spiral symmetry

Manufacturing technologies as injection molding or embossing specify their production limits for minimum radii of the vertices or draft angle for demolding, for instance. These restrictions may limit the system optical efficiency or affect the generation of undesired artifacts on the illumination pattern when dealing with optical design. A novel manufacturing concept is presented here, in which the optical surfaces are not obtained from the usual revolution symmetry with respect to a central axis (z axis), but they are calculated as free-form surfaces describing a spiral trajectory around z axis. The main advantage of this new concept lies in the manufacturing process: a molded piece can be easily separated from its mold just by applying a combination of rotational movement around axis z and linear movement along axis z, even for negative draft angles. The general designing procedure will be described in detail

Toward mass production of microtextured microdevices: linking rapid prototyping with microinjection molding

The possibility of manufacturing textured materials and devices, with surface properties controlled from the design stage, instead of being the result of machining processes or chemical attacks, is a key factor for the incorporation of advanced functionalities to a wide set of micro and nanosystems. Recently developed high-precision additive manufacturing technologies, together with the use of fractal models linked to computer-aided design tools, allow for a precise definition and control of final surface properties for a wide set of applications, although the production of larger series based on these resources is still an unsolved challenge. However, rapid prototypes, with controlled surface topography, can be used as original masters for obtaining micromold inserts for final large-scale series manufacture of replicas using microinjection molding. In this study, an original procedure is presented, aimed at connecting rapid prototyping with microinjection molding, for the mass production of two different microtextured microsystems, linked to tissue engineering tasks, using different thermoplastics as ultimate materials.

Low-cost manufacturing by fused filament fabrication of microwave waveguide passive devices for space applications

Presentación en poster de impresión 3D de guias de onda.

Conceptual plan for an interactive highway safety design model. Final report.

Federal Highway Administration, Office of Safety and Traffic Operations Research and Development, McLean Va.

Remote Control Electrodeposition: Patterning on Substrates without Direct Electrical Connections

Thesis (Ph.D.)--University of Washington, 2016-06

Modelling manufacturing planning and control systems:the application of object-oriented principles and discrete-event simulation

Manufacturing planning and control systems are fundamental to the successful operations of a manufacturing organisation. 10 order to improve their business performance, significant investment is made by companies into planning and control systems; however, not all companies realise the benefits sought Many companies continue to suffer from high levels of inventory, shortages, obsolete parts, poor resource utilisation and poor delivery performance. This thesis argues that the fit between the planning and control system and the manufacturing organisation is a crucial element of success. The design of appropriate control systems is, therefore, important. The different approaches to the design of manufacturing planning and control systems are investigated. It is concluded that there is no provision within these design methodologies to properly assess the impact of a proposed design on the manufacturing facility. Consequently, an understanding of how a new (or modified) planning and control system will perform in the context of the complete manufacturing system is unlikely to be gained until after the system has been implemented and is running. There are many modelling techniques available, however discrete-event simulation is unique in its ability to model the complex dynamics inherent in manufacturing systems, of which the planning and control system is an integral component. The existing application of simulation to manufacturing control system issues is limited: although operational issues are addressed, application to the more fundamental design of control systems is rarely, if at all, considered. The lack of a suitable simulation-based modelling tool does not help matters. The requirements of a simulation tool capable of modelling a host of different planning and control systems is presented. It is argued that only through the application of object-oriented principles can these extensive requirements be achieved. This thesis reports on the development of an extensible class library called WBS/Control, which is based on object-oriented principles and discrete-event simulation. The functionality, both current and future, offered by WBS/Control means that different planning and control systems can be modelled: not only the more standard implementations but also hybrid systems and new designs. The flexibility implicit in the development of WBS/Control supports its application to design and operational issues. WBS/Control wholly integrates with an existing manufacturing simulator to provide a more complete modelling environment.

Product design in the context of the social needs in less industrialised economies

This thesis is related to the subject of technical innovation, specifically to the activity of design in microenterprises operating in less industrialised economies. Design here is understood as a process, which is not the sole domain of formally trained categories such as engineers, architects or industrial designers. The 'professional boundary' discussion in this investigation is perceived as secondary as, in this context, products are designed, copied or adapted by workers, entrepreneurs themselves, or directly by the poor community. Design capacity at this level is considered to be important both in relation to the conception of capital and consumer goods and to the building up of technical knowledge. Although professional design emerged in Latin America little over three decades ago, this activity has remained marginalised throughout industry. Design activity tends to be concentrated in some product categories in the formalised industrial sector. For microenterprises operating informally, industrial design appears to be unknown. The existing literature pays little attention to 'informal design' capacity. Other areas of knowledge, such as development economies, recognise the importance of microenterprises and technological capability but neglect the potential role of industrial design in small manufacturing units. The management literature, though it focuses on technical innovation and design, has also paid little attention to 'informal design'. In less industrialised economies this neglect is felt by the lack of programmes specifically tailored to create or stimulate 'informal design'. There is a need for recognition of 'informal design' capacity and for the implementation of programmes which specifically target design as a central activity in the manufacturing firm, independent of their size and technological capability. Addressing 'design by the poor for the poor', requires a down-to-earth approach.

Humans:the missing link in manufacturing simulation?

Computer based discrete event simulation (DES) is one of the most commonly used aids for the design of automotive manufacturing systems. However, DES tools represent machines in extensive detail, while only representing workers as simple resources. This presents a problem when modelling systems with a highly manual work content, such as an assembly line. This paper describes research at Cranfield University, in collaboration with the Ford Motor Company, founded on the assumption that human variation is the cause of a large percentage of the disparity between simulation predictions and real world performance. The research aims to improve the accuracy and reliability of simulation prediction by including models of human factors.

Simultaneous optimisation of structural topology and material grading using level set method

Peer reviewed

Selective Laser Melting of the Eutectic Silver-Copper Alloy Ag 28 wt % Cu

The aim of this work was to perform a detailed investigation of the use of Selective Laser Melting (SLM) technology to process eutectic silver-copper alloy Ag 28 wt. % Cu (also called AgCu28). The processing occurred with a Realizer SLM 50 desktop machine. The powder analysis (SEM-topography, EDX, particle distribution) was reported as well as the absorption rates for the near-infrared (NIR) spectrum. Microscope imaging showed the surface topography of the manufactured parts. Furthermore, microsections were conducted for the analysis of porosity. The Design of Experiments approach used the response surface method in order to model the statistical relationship between laser power, spot distance and pulse time.

Investigation into the Influence of Build Parameters on Failure of 3D Printed Parts

Additive manufacturing, including fused deposition modeling (FDM), is transforming the built world and engineering education. Deep understanding of parts created through FDM technology has lagged behind its adoption in home, work, and academic environments. Properties of parts created from bulk materials through traditional manufacturing are understood well enough to accurately predict their behavior through analytical models. Unfortunately, Additive Manufacturing (AM) process parameters create anisotropy on a scale that fundamentally affects the part properties. Understanding AM process parameters (implemented by program algorithms called slicers) is necessary to predict part behavior. Investigating algorithms controlling print parameters (slicers) revealed stark differences between the generation of part layers. In this work, tensile testing experiments, including a full factorial design, determined that three key factors, width, thickness, infill density, and their interactions, significantly affect the tensile properties of 3D printed test samples.

Studio e ottimizzazione del processo di fabbricazione additiva (SLM) per applicazioni in ambito biomedicale: produzione di protesi e strutture reticolari

Il progetto di dottorato che verrà presentato in questa tesi è focalizzato sullo sviluppo di un metodo sperimentale per la produzione di protesi personalizzate utilizzando il processo di fabbricazione additiva di Selective Laser Melting (SLM). L’obiettivo è quello di definire una condizione di processo ottimizzata per applicazioni in ambito chirurgico che possa essere generalizzabile, ovvero che ne garantisca la riproducibilità al variare dell’anatomia del paziente e che rappresenti la base per estendere il metodo ad altre componenti protesiche. Il lavoro si è sviluppato lungo due linee principali, la cui convergenza ha permesso di realizzare prototipi di protesi complete utilizzando un solo processo: da una parte la produzione di componenti a massima densità per il raggiungimento di elevate resistenze meccaniche, buona resistenza ad usura e corrosione e controllo di tensioni residue e deformazione delle parti stampate. Dall’altra si sono studiate strutture reticolari a geometria e porosità controllata per favorire l’osteointegrazione della componente protesica post impianto. In questo studio sono stati messe a confronto le possibili combinazioni tra parametri di processo e sono state individuate le correlazioni con le proprietà finali dei componenti stampati. Partendo da queste relazioni si sono sviluppate le strategie tecnologiche per la progettazione e la produzione dei componenti. I test sperimentali svolti e i risultati ottenuti hanno dimostrato la fattibilità dell’utilizzo del processo SLM per la produzione di protesi personalizzate e sono stati fabbricati i primi prototipi funzionali. La fabbricazione di protesi personalizzate richiede, però, anche la progettazione e la produzione di strumentario chirurgico ad hoc. Per questo motivo, parallelamente allo studio della lega di Cromo Cobalto, sono stati eseguiti i test anche su campioni in INOX 316L. Anche in questo caso è stato possibile individuare una finestra operativa di processo che garantisse proprietà meccaniche comparabili, e in alcuni casi superiori, a quelle ottenute con processi convenzionali.

Numerical simulation of the flow and performance evaluation of an aerospike engine

The main focus of this work is to define a numerical methodology to simulate an aerospike engine and then to analyse the performance of DemoP1, which is a small aerospike demonstrator built by Pangea Aerospace. The aerospike is a promising solution to build more efficient engine than the actual one. Its main advantage is the expansion adaptation that allows to reach the optimal expansion in a wide range of ambient pressures delivering more thrust than an equivalent bell-shaped nozzle. The main drawbacks are the cooling system design and the spike manufacturing but nowadays, these issues seem to be overcome with the use of the additive manufacturing method. The simulations are performed with dbnsTurbFoam which is a solver of OpenFOAM. It has been designed to simulate a supersonic compressible turbulent flow. This work is divided in four chapters. The first one is a short introduction. The second one shows a brief summary of the theoretical performance of the aerospike. The third one introduces the numerical methodology to simulate a compressible supersonic flow. In the fourth chapter, the solver has been verified with an experiment found in literature. And in the fifth chapter, the simulations on DemoP1 engine are illustrated.