Optimization of thermoacoustic primemover using response surface methodology

Thermoacoustic engines are energy conversion devices that convert thermal energy from a high-temperature heat source into useful work in the form of acoustic power while diverting waste heat into a cold sink; it can be used as a drive for cryocoolers and refrigerators. Though the devices are simple to fabricate, it is very challenging to design an optimized thermoacoustic primemover with better performance. The study presented here aims to optimize the thermoacoustic primemover using response surface methodology. The influence of stack position and its length, resonator length, plate thickness, and plate spacing on pressure amplitude and frequency in a thermoacoustic primemover is investigated in this study. For the desired frequency of 207 Hz, the optimized value of the above parameters suggested by the response surface methodology has been conducted experimentally, and simulations are also performed using DeltaEC. The experimental and simulation results showed similar output performance.

Evaluation of isopentane, R-245fa and their mixtures as working fluids for organic Rankine cycles

Low grade thermal energy from sources such as solar, geothermal and industrial waste heat in the temperature range of 380-425 K can be converted to electrical energy with reasonable efficiency using isopentane and R-245fa. While the former is flammable and the latter has considerable global warming potential, their mixture in 0.7/0.3 mole fraction is shown to obviate these disadvantages and yet retain dominant merits of each fluid. A realistic thermodynamic analysis is carried out wherein the possible sources of irreversibilities such as isentropic efficiencies of the expander and the pump and entropy generation in the regenerator, boiler and condenser are accounted for. The performance of the system in the chosen range of heat source temperatures is evaluated. A technique of identifying the required source temperature for a given output of the plant and the maximum operating temperature of the working fluid is developed. This is based on the pinch point occurrence in the boiler and entropy generation in the boiling and superheating regions of the boiler. It is shown that cycle efficiencies of 10-13% can be obtained in the range investigated at an optimal expansion ratio of 7-10. (C) 2012 Elsevier Ltd. All rights reserved.

Evaluation of carbon dioxide blends with isopentane and propane as working fluids for organic Rankine cycles

The main theme of this paper is to study the flammability suppression of hydrocarbons by blending with carbon dioxide, and to evaluate these mixtures as possible working fluids in organic Rankine cycle for medium temperature concentrated solar power applications. The analysis takes into account inevitable irreversibilities in the turbine, the pump, and heat exchangers. While the isopentane + CO2 mixture suffers from high irreversibility mainly in the regenerator owing to a large temperature glide, the propane + CO2 mixture performs more or less the same as pure propane albeit with high cycle pressures. In general, large temperature glides at condensing pressures extend the heat recovery into the two-phase dome, which is an advantage. However, at the same time, the shift of the pinch point towards the warm end of the regenerator is found to be a major cause of irreversibility. In fact, as the number of carbon atoms in alkanes decreases, their blend with CO2 moves the pinch point to the colder end of the regenerator. This results in lower entropy generation in the regenerator and improved cycle efficiency of propane + CO2 mixtures. With this mixture, real cycle efficiencies of 15-18% are achievable at a moderate source temperature of 573 K. Applicability for a wide range of source temperatures is found to be an added advantage of this mixture.

Nanostructuring of p- and n-type skutterudites reaching figures of merit of approximately 1.3 and 1.6, respectively

Thermoelectric (TE) conversion of waste heat into useful electricity demands optimized thermal and electrical transport in the leg material over a wide temperature range. In order to gain a reasonably high figure of merit (ZT) as well as high thermal electric conversion efficiency, various conditions of the starting material were studied: industrially produced skutterudite powders of p-type DDy(Fe1-xCox)(4)Sb-12 (DD: didymium) and n-type (Mm, Sm)(y)Co4Sb12 (Mm: mischmetal) were used. After a rather fast reaction-melting technique, the bulk was crushed and sieved with various strainers in order to obtain particles below the respective mesh sizes, followed by ball-milling under three different conditions. The dependence of the TE properties (after hot pressing) on the micro/nanosized particles, grains and crystallites was investigated. Optimized conditions resulted in an increase of ZT for bulk material to current record-high values: from ZT similar to 1.1 to ZT similar to 1.3 at 775 K for p-type and from ZT similar to 1.0 to ZT similar to 1.6 at 800 K for n-type, resulting in respective efficiencies (300-850 K) of eta > 13% and eta similar to 16%. (C) 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Numerical and Experimental Investigation On The Prevention of Co Deflagration

The exhaust gases from industrial furnaces contain a huge amount of heat and chemical enthalpy. However, it is hard to recover this energy since exhaust gases invariably contain combustible components such as carbon monoxide (CC). If the CO is unexpectedly ignited during the heat recovery process, deflagration or even detonation could occur, with serious consequences such as complete destruction of the equipment. In order to safely utilize the heat energy contained in exhaust gas, danger of its explosion must be fully avoided. The mechanism of gas deflagration and its prevention must therefore be studied. In this paper, we describe a numerical and experimental investigation of the deflagration process in a semi-opened tube. The results show that, upon ignition, a low-pressure wave initially spreads within the tube and then deflagration begins. For the purpose of preventing deflagration, an appropriate amount of nitrogen was injected into the tube at a fixed position. Both simulation and experimental results have shown that the injection of inert gas can successfully interrupt the deflagration process. The peak value of the deflagration pressure can thereby be reduced by around 50%. (C) 2008 Elsevier Ltd. All rights reserved.

Band Engineering in Thermoelectric Materials Using Optical, Electronic, and Ab-Initio Computed Properties

Thermoelectric materials have demanded a significant amount of attention for their ability to convert waste heat directly to electricity with no moving parts. A resurgence in thermoelectrics research has led to significant enhancements in the thermoelectric figure of merit, zT, even for materials that were already well studied. This thesis approaches thermoelectric zT optimization by developing a detailed understanding of the electronic structure using a combination of electronic/thermoelectric properties, optical properties, and ab-initio computed electronic band structures. This is accomplished by applying these techniques to three important classes of thermoelectric materials: IV-VI materials (the lead chalcogenides), Half-Heusler’s (XNiSn where X=Zr, Ti, Hf), and CoSb₃ skutterudites.

In the IV-VI materials (PbTe, PbSe, PbS) I present a shifting temperature-dependent optical absorption edge which correlates well to the computed ab-initio molecular dynamics result. Contrary to prior literature that suggests convergence of the primary and secondary bands at 400 K, I suggest a higher convergence temperature of 700, 900, and 1000 K for PbTe, PbSe, and PbS, respectively. This finding can help guide electronic properties modelling by providing a concrete value for the band gap and valence band offset as a function of temperature.

Another important thermoelectric material, ZrNiSn (half-Heusler), is analyzed for both its optical and electronic properties; transport properties indicate a largely different band gap depending on whether the material is doped n-type or p-type. By measuring and reporting the optical band gap value of 0.13 eV, I resolve the discrepancy in the gap calculated from electronic properties (maximum Seebeck and resistivity) by correlating these estimates to the electron-to-hole weighted mobility ratio, A, in narrow gap materials (A is found to be approximately 5.0 in ZrNiSn).

I also show that CoSb₃ contains multiple conduction bands that contribute to the thermoelectric properties. These bands are also observed to shift towards each other with temperature, eventually reaching effective convergence for T>500 K. This implies that the electronic structure in CoSb₃ is critically important (and possibly engineerable) with regards to its high thermoelectric figure of merit.

Design for Survival: Sustainability for Planet and Structure

Buildings in Port Aransas encounter drastic environmental challenges: the potential catastrophic storm surge and high winds from a hurricane, and daily conditions hostile to buildings, vehicles, and even most vegetation. Its location a few hundred feet from the Gulf of Mexico and near-tropical latitude expose buildings to continuous high humidity, winds laden with scouring sand and corrosive salt, and extremes of temperature and ultraviolet light. Building construction methods are able to address each of these, but doing so in a sustainable way creates significant challenges. The new research building at the Marine Science Institute has been designed and is being constructed to meet the demand for both survivability and sustainability. It is tracking towards formal certification as a LEED Gold structure while being robust and resistant to the harsh coastal environment. The effects of a hurricane are mitigated by elevating buildings and providing a windproof envelope. Ground-level enclosures are designed to be sacrificial and non-structural so they can wash or blow away without imposing damage on the upper portions of the building, and only non-critical functions and equipment will be supported within them. Design features that integrate survivability with sustainability include: orientation of building axis; integral shading from direct summer sunlight; light wells; photovoltaic arrays; collection of rainwater and air conditioning condensate for use in landscape irrigation; reduced impervious cover; xeriscaping and indigenous plants; recycling of waste heat from air conditioning systems; roofing system that reflects light and heat; long life, low maintenance stainless steel, high-tensile vinyl, hard-anodized aluminum and hot-dipped galvanized mountings throughout; chloride-resistant concrete; reduced visual impact; recycling of construction materials.

Thermoelectric Cooling and Power Generation

In a typical thermoelectric device, a junction is formed from two different conducting materials, one containing positive charge carriers (holes) and the other negative charge carriers (electrons). When an electric current is passed in the appropriate direction through the junction, both types of charge carriers move away from the junction and convey heat away, thus cooling the junction. Similarly, a heat source at the junction causes carriers to flow away from the junction, making an electrical generator. Such devices have the advantage of containing no moving parts, but low efficiencies have limited their use to specialty applications, such as cooling laser diodes. The principles of thermoelectric devices are reviewed and strategies for increasing the efficiency of novel materials are explored. Improved materials would not only help to cool advanced electronics but could also provide energy benefits in refrigeration and when using waste heat to generate electrical power.

Design and Operation of A 5.5 MWe Biomass Integrated Gasification Combined Cycle Demonstration Plant

The design and operation of a 5.5 MWe biomass integrated gasification combined cycle (IGCC) demonstration plant, which is located in Xinghua, Jiangsu Province of China, are introduced. It is the largest complete biomass gasification power plant that uses rice husk and other agricultural wastes as fuel in Asia. It mainly consists of a 20 MWt atmospheric circulating fluidized-bed gasifier, a gas-purifying system, 10 sets of 450 kW(e) gas engines, a waste heat boiler, a 1.5 MWe steam turbine, a wastewater treatment system, etc. The demonstration plant has been operating since the end of 2005, and its overall efficiency reaches 26-28%. Its capital cost is less than 1200 USD/kW, and its running cost is about 0.079 USD/kWh based on the biomass price of 35.7 USD/ton. There is a 20% increment on capital cost and 35% decrease on the fuel consumption compared to that of a 1 MW system without a combined cycle. Because only part of the project has been performed, many of the tests still remain and, accordingly, must be reported at a later opportunity.

Mathematical Modelling of a Reciprocating Piston Expander

Modern internal combustion (IC) engines reject around two thirds of the energy provided by the fuel as low-grade waste heat. Capturing a portion of this waste heat energy and transforming it into a more useful form of energy could result in a significant reduction in fuel consumption. By using the low-grade heat, an organic Rankine cycle (ORC) can produce mechanical work from a pressurised organic fluid with the use of an expander.
Ideal gas assumptions are shown to produce significant errors in expander performance predictions when using an organic fluid. This paper details the mathematical modelling technique used to accurately model the thermodynamic processes for both ideal and non-ideal fluids within the reciprocating expander. A comparison between the two methods illustrates the extent of the errors when modelling a reciprocating piston expander. Use of the ideal gas assumptions are shown to produce an error of 55% in the prediction of power produced by the expander when operating on refrigerant R134a.

Improving fuel economy application of the organic Rankine Cycle on a hybrid bus

Globally vehicle operators are experiencing rising fuel costs and increased
running expenses as governments around the world attempt to decrease carbon dioxide emissions and fossil fuel consumption, due to global warming and the drive to reduce dependency on fossil fuels. Recent advances in hybrid vehicle design have made great strides towards more efficient operation, with regenerative braking being widely used to capture otherwise lost energy. In this paper a hybrid series bus is developed a step further, by installing another method of energy capture on the vehicle. In this case, it is in the form of the Organic Rankine Cycle (ORC). The waste heat expelled to the exhaust and coolant streams is recovered and converted to electrical energy which is then stored in the hybrid vehicles batteries. The electrical energy can then be used for the auxiliary power circuit or to assist in vehicle propulsion, thus reducing the load on the engine, thereby improving the overall fuel economy of the vehicle and reducing carbon dioxide emissions.

Case study investigation of indoor air quality in mechanically ventilated and naturally ventilated UK social housing

There is a significant lack of indoor air quality research in low energy homes. This study compared the indoor air quality of eight
newly built case study homes constructed to similar levels of air-tightness and insulation; with two different ventilation strategies (four homes with Mechanical Ventilation with Heat Recovery (MVHR) systems/Code level 4 and four homes naturally ventilated/Code level 3). Indoor air quality measurements were conducted over a 24 h period in the living room and main bedroom of each home during the summer and winter seasons. Simultaneous outside measurements and an occupant diary were also employed during the measurement period. Occupant interviews were conducted to gain information on perceived indoor air quality, occupant behaviour and building related illnesses. Knowledge of the MVHR system including ventilation related behaviour was also studied. Results suggest indoor air quality problems in both the mechanically ventilated and naturally ventilated homes, with significant issues identified regarding occupant use in the social homes

An investigation of IAQ, thermal comfort and Sick Building Syndrome symptoms in UK energy efficient homes

Purpose
– Concern of the deterioration of indoor environmental quality as a result of energy efficient building design strategies is growing. Apprehensions of the effect of airtight, super insulated envelopes, the reduction of infiltration, and the reliance on mechanical systems to provide adequate ventilation (air supply) is promoting emerging new research in this field. The purpose of this paper is to present the results of an indoor air quality (IAQ) and thermal comfort investigation in UK energy efficient homes, through a case study investigation.

Design/methodology/approach
– The case study dwellings consisted of a row of six new-build homes which utilize mechanical ventilation with heat recovery (MVHR) systems, are built to an average airtightness of 2m3/m2/hr at 50 Pascal’s, and constructed without a central heating system. Physical IAQ measurements and occupant interviews were conducted during the summer and winter months over a 24-hour period, to gain information on occupant activities, perception of the interior environment, building-related health and building use.

Findings
– The results suggest inadequate IAQ and perceived thermal comfort, insufficient use of purge ventilation, presence of fungal growth, significant variances in heating patterns, occurrence of sick building syndrome symptoms and issues with the MVHR system.

Practical implications
– The findings will provide relevant data on the applicability of airtight, mechanically ventilated homes in a UK climate, with particular reference to IAQ.

Originality/value
– IAQ data of this nature is essentially lacking, particularly in the UK context. The findings will aid the development of effective sustainable design strategies that are appropriate to localized climatic conditions and sensitive to the health of building occupants.

Microstructure design of Titanate-based electroceramics

Electrocerâmicos são uma classe de materiais avançados com propriedades eléctricas valiosas para aplicações. Estas propriedades são geralmente muito dependentes da microestrutura dos materiais. Portanto, o objectivo geral deste trabalho é investigar o desenho da resposta dieléctrica de filmes espessos obtidos por Deposição Electroforética (EPD) e cerâmicos monolíticos, através do controlo da evolução da microestrutura durante a sinterização de electrocerâmicos à base de titanatos. Aplicações sem fios na indústria microelectrónica e de comunicações, em rápido crescimento, tornaram-se um importante mercado para os fabricantes de semicondutores. Devido à constante necessidade de miniaturização, redução de custos e maior funcionalidade e integração, a tecnologia de filmes espessos está a tornar-se uma abordagem de processamento de materiais funcionais cada vez mais importante. Uma técnica adequada neste contexto é EPD. Os filmes espessos resultantes necessitam de um passo subsequente de sinterização que é afectada pelo substrato subjacente, tendo este um forte efeito sobre a evolução da microestrutura. Relacionado com a miniaturização e a discriminação do sinal, materiais dieléctricos usados como componentes operando a frequências das microondas em aplicações na industria microelectrónica de comunicações devem apresentar baixas perdas dieléctricas e elevadas permitividade dieléctrica e estabilidade com a temperatura. Materiais do sistema BaO-Ln2O3- TiO2 (BLnT: Ln = La ou Nd), como BaLa4Ti4O15 (BLT) e Ba4.5Nd9Ti18O54 (BNT), cumprem esses requisitos e são interessantes para aplicações, por exemplo, em estações de base para comunicações móveis ou em ressonadores para telefones móveis, onde a miniaturização dos dispositivos é muito importante. Por sua vez, o titanato de estrôncio (SrTiO3, STO) é um ferroeléctrico incipiente com constante dieléctrica elevada e baixas perdas, que encontra aplicação em, por exemplo, condensadores de camada interna, tirando partido de fronteiras de grão altamente resistivas. A dependência da permitividade dieléctrica do campo eléctrico aplicado torna este material muito interessante para aplicações em dispositivos de microondas sintonizáveis. Materiais à base de STO são também interessantes para aplicações termoeléctricas, que podem contribuir para a redução da actual dependência de combustíveis fósseis por meio da geração de energia a partir de calor desaproveitado. No entanto, as mesmas fronteiras de grão resistivas são um obstáculo relativamente à eficiência do STO para aplicações termoeléctricas. Para além do efeito do substrato durante a sinterização constrangida, outros factores, como a presença de fase líquida, a não-estequiometria ou a temperatura de sinterização, afectam significativamente não apenas a microestrutura dos materiais funcionais, mas também a sua resposta dieléctrica. Se adequadamente compreendidos, estes factores podem ser intencionalmente usados para desenhar a microestrutura dos electrocerâmicos e, desta forma, as suas propriedades dieléctricas. O efeito da não-estequiometria (razão Sr/Ti 0.995-1.02) no crescimento de grão e resposta dieléctrica de cerâmicos de STO foi investigado neste trabalho. A mobilidade das fronteiras de grão aumenta com a diminuição da razão Sr/Ti. A resistividade do interior dos grãos e das fronteiras de grão é sistematicamente diminuída em amostras não-estequiométricas de STO, em comparação com o material estequiométrico. O efeito é muito mais forte para as fronteiras de grão do que para o seu interior. Dependências sistemáticas da não-estequiometria foram também observadas relativamente à dependência da condutividade da temperatura (muito mais afectada no caso da contribuição das fronteiras de grão), à capacitância do interior e fronteiras de grão e à espessura das fronteiras de grão. Uma anomalia no crescimento de grão em cerâmicos de STO ricos em Ti foi também observada e sistematicamente analisada. Foram detectadas três descontinuidades na dependência do tipo Arrhenius do crescimento de grão relativamente à temperatura com diminuições no tamanho de grão a temperaturas em torno de 1500, 1550 e 1605 °C. Além disso, descontinuidades semelhantes foram também observadas na dependência da energia de activação relativamente à condutividade das fronteiras de grão e na espessura das fronteiras de grão, avaliadas por Espectroscopia de Impedância. Estas notáveis coincidências suportam fortemente a formação de diferentes complexos de fronteira de grão com transições entre os regimes de crescimento de grão observados, que podem ser correlacionados com diferentes mobilidades de fronteira de grão e propriedades dieléctricas. Um modelo é sugerido, que se baseia na diminuição da fase líquida localizada nas fronteiras de grão, como o aumento da temperatura de sinterização, um cenário compatível com um fenómeno de solubilidade retrógrada, observado anteriormente em metais e semicondutores, mas não em cerâmicos. A EPD de filmes espessos de STO em substratos de folha de Pt e a sinterização constrangida dos filmes fabricados foram também preliminarmente tratadas. Filmes espessos de STO foram depositados com êxito por EPD sobre substratos de Pt e, depois de sinterizados, atingiram densidades elevadas. Um aumento da densificação e do tamanho de grão assim como o alargamento da distribuição de tamanho do grão foram observados com a diminuição da razão Sr/Ti, tal como anteriormente observado em amostras cerâmicas. Grãos equiaxiados foram observados para todas as composições, mas um certo grau de anisotropia na orientação dos poros foi detectado: os poros revelaram uma orientação vertical preferencial. Este trabalho focou-se também na sinterização constrangida do sistema BLnT (Ln = La ou Nd), nomeadamente de filmes espessos de BLT e BNT sobre substratos de folha de platina, e na relação do desenvolvimento de anisotropia microestrutural com as propriedades dieléctricas. As observações durante a sinterização constrangida foram comparadas com cerâmicos monolíticos equivalentes sinterizados livremente. Filmes espessos de BLnT (Ln = La ou Nd) com elevada densidade foram obtidos por EPD e subsequente sinterização constrangida. A anisometria cristalográfica do material em conjunto com um passo de sinterização constrangida resultou em grãos alongados e microestruturas anisotrópicas. O efeito do stress do substrato durante a sinterização constrangida originou graus mais elevados de anisotropia (grãos e poros alongados e orientação preferencial, bem como textura cristalográfica) nos filmes sinterizados relativamente aos cerâmicos equivalentes sinterizados livremente, não obstante o estado equivalente das amostras em verde. A densificação dos filmes de BLnT (Ln = La ou Nd) é retardada em comparação com os cerâmicos, mas depois de longos tempos de sinterização densidades semelhantes são obtidas. No entanto, em oposição a observações na sinterização constrangida de outros sistemas, o crescimento do grão em filmes de BLnT (Ln = La ou Nd) é favorecido pelo constrangimento causado pelo substrato. Além disso, grãos e poros alongados orientados paralelamente ao substrato foram desenvolvidos durante a sinterização constrangida de filmes espessos. Verificou-se uma forte correlação entre a evolução de grãos e poros, que começou assim que o crescimento do grão se iniciou. Um efeito da tensão do substrato no aumento do crescimento de grão, bem como um forte “Zener pinning”, origina microestruturas altamente texturizadas, o que também é observado a nível cristalográfico. Efeitos marcantes da anisotropia microestrutural foram também detectados nas propriedades dieléctricas dos filmes de BLnT (Ln = La ou Nd). Juntamente com o aumento da razão de aspecto dos grãos, do factor de orientação e do grau de textura cristalográfica, a permitividade relativa é ligeiramente diminuída e o coeficiente de temperatura da permitividade evolui de negativo para positivo com o aumento do tempo isotérmico de sinterização. Este trabalho mostra que a não-estequiometria pode ser usada para controlar a mobilidade das fronteiras de grão e, portanto, desenhar a microestrutura e as propriedades dieléctricas de electrocerâmicos à base de STO, com ênfase nas propriedades das fronteiras de grão. O papel da não-estequiometria no STO e dos complexos de fronteira de grão no desenvolvimento microestrutural é discutido e novas oportunidades para desenhar as propriedades de materiais funcionais são abertas. As observações relativamente à sinterização constrangida apontam para o efeito de tensões mecânicas desenvolvidas devido ao substrato subjacente no desenvolvimento da microestrutura de materiais funcionais. É assim esperado que a escolha adequada de substrato permitia desenhar a microestrutura de filmes espessos funcionais com desempenho optimizado. “Stress Assisted Grain Growth” (SAGG) é então proposto como uma técnica potencial para desenhar a microestrutura de materiais funcionais, originando microestruturas anisotrópicas texturizadas com propriedades desejadas.

A new combined joules supercritical rankine cycle exergetic analysis and optimization

The application of a supercritical Rankine cycle in combined cycles does not happen in today’s thermoelectric power stations. Nevertheless, the most recent development in gas turbines, that allows a high efficiency and high exhaust gases temperatures, and the improvement of high pressure and temperature alloys, makes this cycle possible. This study’s intent is to prove the viability of this combined cycle, since it can break the 60% efficiency barrier, which is the plafond in actual power stations. To attain this target, several configurations for this cycle have been simulated, optimized and analyzed [1]. The simulations were done with the computational program IPSEpro [2] and the optimizations were effectuated with software developed for the effect, using the DFP method [3]. In parallel with the optimization that claims the cycle’s efficiency maximization, an exergetic analysis was also made [4] to all the cycle components. In opposite to what happens in subcritical combined cycles, it was demonstrated that in supercritical combined cycles the higher efficiency takes place with a single steam pressure in the heat recovery steam generator (HRSG).