Pultrusion of fibre reinforced thermoplastic pre-impregnated materials

Fibre reinforced thermoplastic pre impregnated materials produced continuously by diverse methods and processing conditions were used to produce composites using pultrusion. The processing windows used to produce these materials and composites profiles were optimized by using the Taguchi / DOE (Design of Experiments) methods. Composites were manufactured by pultrusion and compression moulding and subsequently submitted to mechanical testing and microscopy analysis. The obtained results were compared with the expected theoretical ones predicted from the Rule of Mixtures (ROM) and with those of similar engineering conventional available materials. The results obtained shown that produced composites have adequate properties for applications in common and structural engineering markets.

Presence of starch enhances in vitro biodegradation and biocompatibility of a gentamicin delivery formulation

The effect of α-amylase degradation on the release of gentamicin from starch-conjugated chitosan microparticles was investigated up to 60 days. Scanning electron microscopic observations showed an increase in the porosity and surface roughness of the microparticles as well as reduced diameters. This was confirmed by 67% weight loss of the microparticles in the presence of α-amylase. Over time, a highly porous matrix was obtained leading to increased permeability and increased water uptake with possible diffusion of gentamicin. Indeed, a faster release of gentamicin was observed with α-amylase. Starch-conjugated chitosan particles are non-toxic and highly biocompatible for an osteoblast (SaOs-2) and fibroblast (L929) cell line as well as adipose-derived stem cells. When differently produced starch-conjugated chitosan particles were tested, their cytotoxic effect on SaOs-2 cells was found to be dependent on the crosslinking agent and on the amount of starch used.

Efecto de la incorporación de proteínas de origen vegetal sobre sistemas alimenticios basados en almidón. Effect of vegetal protein addition to gelled-starch food.

La soja y el maní son cultivos de gran importancia en la provincia de Córdoba y en la Argentina. La utilización de proteínas vegetales se ha incrementado notablemente debido a su alto valor nutricional y a sus atributos funcionales deseables. Las harinas de soja y de maní, subproductos de la extracción de aceite, presentan un alto contenido de proteínas vegetales de excelente calidad nutricional, de bajo precio y con escaso nivel de aprovechamiento en la industria alimenticia. Los concentrados de proteínas de soja son poco utilizados en la elaboración de alimentos, además el desarrollo de concentrados de proteínas de maní puede proveer a la industria de un nuevo ingrediente con alto contenido de proteínas para la formulación y fortificación de alimentos tradicionales. Los postres listos para consumir disponibles en el mercado, están formados por mezclas de almidón gelificado y derivados lácteos, sobre los que se agregan diversos aditivos alimentarios (como sacarosa, aromatizantes, espesantes, etc.). La incorporación de proteínas vegetales puede ser una eficaz forma de incrementar el nivel de proteínas y, en consecuencia, el valor nutricional de estos productos. Además de ser una alternativa a los alimentos elaborados con proteínas animales. Pese a que Córdoba es un gran productor de soja y maní, sus derivados no son empleados actualmente como ingredientes en este tipo de alimentos.El objetivo general de este proyecto es estudiar el efecto de la incorporación de proteínas de origen vegetal sobre las propiedades físico-químicas y funcionales de sistemas alimenticios basados en almidón gelatinizado, prestando fundamental atención a las interacciones que se establecen entre las diferentes moléculas. Se planifica obtener concentrados de proteínas a partir de harina desgrasada de soja y de maní y estudiar su composición y sus propiedades funcionales. Se elaborarán mezclas de los concentrados con almidones de maíz, mandioca y trigo. Se estudiará el comportamiento termo-mecánico de las mezclas y la calidad de los geles mediante la cantidad de agua liberada, el perfil reológico y el color. También se realizarán análisis sensoriales para la selección de los parámetros de calidad de los geles y se estudiarán la digestibilidad de las proteínas y del almidón. Al mismo tiempo se estudiarán las interacciones químicas y físicas entre los distintos componentes. Los resultados servirán para generar y difundir conocimientos sobre la relación entre las interacciones y la calidad de los productos, lo que facilitará la optimización de formulaciones y procesos.

Impact of the C2/C6 ratio of high-molecular-weight hydroxyethyl starch on pharmacokinetics and blood coagulation in pigs

Rapport de synthèse : Contexte: l'hydroxyéthylamidon (HEA) est largement utilisé comme expanseur volémique en anesthésiologie et réanimation. Cependant, cette classe de produits perturbe le system de la coagulation. Des améliorations restent possibles dans le choix de la combinaison optimale de poids moléculaire, de degré de substitution en radicaux éthyle et de localisation de ces radicaux sur le squelette glucidique des polymères, afin d'optimiser leur efficacité et leur tolérance. L'HEA de poids moléculaire élevé et faiblement substitué n'affecte pas plus la coagulation sanguine que de l'HEA de bas poids moléculaire faiblement substitué. Nous examinons in vivo l'effet d'un abaissement du rapport C2/C6 sur les caractéristiques pharmacocinétiques et l'impact sur la coagulation sanguine d'un HEA de haut poids moléculaire faiblement substitué. Matériels et méthode: nous comparons dans une étude prospective, randomisée et parallèle l'HEA 650/0.42/2.8 avec l'HEA 650/0.42/5.6 auprès de 30 cochons. Avant, pendant et jusqu'à 630 minutes après une perfusion de 30 ml/kg d'HEA, des échantillons sanguins ont été collectés pour mesurer les concentrations d'HEA, les tests de coagulation plasmatique classiques et la coagulation sanguine par thrombélastographie (TEG®, Haemoscope Corporation, Niles, II, U.S.). Les paramètres pharmacocinétiques ont été estimés en adaptant un modèle à deux compartiments. Résultats: la constante d'élimination est de 0.009 ± 0.001 (min-1) pour l'HEA 650/0.42/2.8 et 0.007 ± 0.001 (min-1) pour l'HEA 650/0.42/5.6 (p<0.001); la surface sous la courbe de concentration est de 1374 ± 340 min*g/L pour l'HEA 650/0.42/2.8 et 1697 ± 411 min*g/L pour l'HEA 650/0.42/5.6 (p=0.026). Les concentrations mesurées d'HEA ne montrent pas de différence entre l'HEA 650/0.42/2.8 et l'HEA 650/0.42/5.6. Les deux solutions d'HEA affectent de façon identique la coagulation sanguine: l'index de coagulation thrombélastographique diminue pareillement à ta fin de la perfusion d'HEA 650/0.42/2.8 et d'HEA 650/0.42/5.6 (p=0.29). De même, le temps de thromboplastine partielle activée et le temps de prothrombine augmentent de manière similaire pour l'HEA 650/0.42/2.8 et l'HEA 650/0.42/5.6 (p=0.83). Conclusion: la réduction du rapport C2/C6 de l'HEA de poids moléculaire élevé et faiblement substitué aboutit à une élimination légèrement accélérée d'HEA. Cependant, elle ne modifie pas l'effet perturbateur sur la coagulation.

Molecular weight of hydroxyethyl starch : is there an effect on blood coagulation and pharmacokinetics ?

Résumé Fondement : le développement de solutions d'hydroxy-éthyl-amidons (HEAS) avec peu d'impact sur la coagulation sanguine, mais un effet supérieur sur la volémie, par comparaison aux HEAS couramment utilisés, est d'un grand intérêt clinique. Nous posons l'hypothèse que des solutions de haut poids moléculaire et de bas degré de substitution possèdent ces caractéristiques. Méthode : trente porcs ont été perfusés avec trois HEAS différents (20 ml/kg) de même degré de substitution (0.42) mais de poids moléculaire différent (130, 500 et 900 kDa). Une série de prélèvements sanguins ont été effectués sur 24 heures, sur lesquels des analyses de coagulation sanguine étaient effectuées par thromboélastographie et dosages plasmatiques. De plus, la concentration plasmatique ainsi que le poids moléculaire in vivo ont été déterminés, ainsi que des paramètres de pharmacocinétiques, ceci en se basant sur un modèle bi-compartimental. Résultats : les analyses de thromboélastographie et les tests de coagulation plasmatique n'ont pas démontré d'altération plus marquée de la coagulation sanguine après l'utilisation des solutions des HAES 500 et HAES 900, par comparaison avec celle de HAES 130. Par contre, les HAES 500 et HAES 900 ont présenté une plus grande aire sous la courbe (area under the curve), dans la relation concentration en fonction du temps [1542 (142) g min litre-1, p<0.001, 1701 (321) g min litre-1, p<0.001] par rapport au HAES 130 [1156 (223) g min litre-1]. La demi-vie alpha (t ½α) était plus longue pour les HAES 500 [53.8 (8.6) min, p<0.01] et HAES 900 [57.1 (12.3) min, p<0.01 ]que pour le HAES 130 [39.9 (10.7) min]. La demi-vie beta (t½β) était par contre similaire pour les trois types de HAES [de 332 (100) à 381 (63) min]. Conclusions : pour les HAES de bas degré de substitution, le poids moléculaire n'est pas un facteur clé en ce qui concerne l'altération de la coagulation. La persistance intravasculaire initialement plus longue des HAES de haut poids moléculaire et bas degré de substitution pourrait résulter dans un plus long effet volémique de ces substances. Abstract Background: The development of hydroxyethyl starches (HES) with low impact on blood coagulation but higher volume effect compared with the currently used HES solutions is of clinical interest. We hypothesized that high molecular weight, low-substituted HES might possess these properties. Methods: Thirty pigs were infused with three different HES solutions (20 ml kg-1) with the same degree of molar substitution (0.42) but different molecular weights (130, 500 and 900 kDa). Serial blood samples were taken over 24 h and blood coagulation was assessed by Thromboelastograph® analysis and analysis of plasma coagulation. In addition, plasma concentration and in vivo molecular weight were determined and pharmacokinetic data were computed based on a two-compartment model. Results: Thromboelastograph analysis and plasma coagulation tests did not reveal a more pronounced alteration of blood coagulation with HES 500 and HES 900 compared with HES 130. In contrast, HES 500 and HES 900 had a greater area under the plasma concentration-time curve [1542 (142) g min litre-1, P<0.001, 1701 (321) g min litre-1, P<0.001] than HES 130 [I 156 (223) g min litre-1] and alpha half life (t ½α) was longer for HES 500 [53.8 (8.6) min, P<0.01 ] and HES 900 [57. I (I 2.3) min, P<0.01 ] than for HES 130 [39.9 (I 0.7) min]. Beta half life (t½β), however, was similar for all three types of HES [from 332 (100) to 381 (63) min]. Conclusions. In low-substituted HES, molecular weight is not a key factor in compromising blood coagulation. The longer initial intravascular persistence of high molecular weight lowsubstituted HES might result in a longer lasting volume effect.

Thermoplastic Pavement Markings, HR-172, 1975

It is difficult to maintain reflectorized lane markings on high-traffic, multi-lane highways. This is particularly true of sections in urban areas where there are frequent lane changes, such as on the Des Moines Freeway, I-235. In spite of the fact that the lane markings are painted on an average of three times a year, they are frequently absent during a considerable portion of the winter period. In the summer of 1973, the office of Highway Maintenance suggested a research project using a new thermoplastic paint developed by the Prismo Universal Corporation. Because of difficulties in scheduling the work, a definite proposal was not submitted until 1974. Upon the recommendation of the Iowa Highway Research Board, the project was approved by the Iowa State Highway Commission on August 7, 1974.

Epoxy and Thermoplastic Pavement Markings on US 30 in Carroll County, HR-545, 1995

A one mile section each of thermoplastic and epoxy pavement marking materials were placed on new ACC pavement near Carroll, IA on Highway 30. The markings were evaluated for four years to see if they were suitable materials for durable pavement markings. The epoxy markings were inadvertently repainted after two years. They were performing well up to that time with little plow damage and good retroreflectivity. The thermoplastic dash lines suffered heavy snow plow damage after the first year and were repainted after the third winter. The thermoplastic edge lines performed fairly well for four years.

Epoxy Thermoplastic Traffic Marking Material, HR-1033, 1982

This Implementation Package summarizes the result of an effort to develop a more durable traffic marking material-Epoxy Thermoplastic (ETP). The report includes background information on the development of ETP, a discussion of the field tests and evaluations, the material composition and equipment modifications for applying ETP. The package also includes material specifications for purchasing ETP and specifications for the application of ETP by contract.

Molar substitution and C2/C6 ratio of hydroxyethyl starch: influence of blood coagulation

Résumé Cette étude a démontré l'effet individuel sur la coagulation sanguine humaine des deux principales caractéristiques de la molécule d'hydroxyéthylamidon (HES) : la substitution molaire et le rapport C2/C6. L'analyse par thrombélastographe (TEG®) indique que la molécule de HES dont la substitution molaire est de 0.42 et le rapport C2/C6 de 2.7 a le moins d'effet sur la coagulation sanguine chez l'être humain. Objectifs de l'étude Le développement d'hydroxyéthylamidons (HES) qui ont à la fois peu d'impact sur la coagulation sanguine et une longue persistance intravasculaire est d'un grand intérêt clinique. Une précédente étude in vitro a démontré qu'une solution de HES de haut poids moléculaire et de bas degré de substitution molaire ne compromettait pas plus la coagulation sanguine qu'une solution HES de poids moléculaire moyen (1). La présente étude examine l'effet individuel de la substitution molaire et du rapport C2/C6 d'une solution de HES de haut poids moléculaire (700 kDa) sur la coagulation sanguine. Matériel et méthode Nous avons prélevé du sang chez 30 adultes en bonne santé; le sang a été mélangé avec 6 solutions de HES qui diffèrent par leur degré de substitution molaire (0.42 et 0.51) et leur rapport C2/C6 (2.7, 7 et 14) à trois degrés de dilution : 20%, 40% et 60%. Les échantillons ont ensuite été analysés par thrombélastographe. Les données ont été étudiées par analyse de variance à trois voies pour mesures répétées sur une voie (dilution). Résultats Plus la substitution molaire est élevée, plus la coagulation sanguine est compromise et ce concernant tous les paramètres du TEG® (tous les p sont < à 0.05). La solution HES avec le rapport C2/C6 le plus bas a l'effet le moins prononcé sur le temps r (p<0.001), l'angle α (p=0.003) et l'Index de Coagulation CI (p<0.001) ; on n'a pas observé d'effet sur le temps k (p=0.513) et l'amplitude maximale (p=0.699) concernant ce paramètre. Conclusion L'analyse par thrombélastographe révèle qu'une molécule de HES avec une substitution molaire de 0.42 et un rapport C2/C6 de 2.7 a un effet minimal sur la coagulation sanguine humaine in vitro.

Thermoplastic bioactive composite – with special reference to dissolution behaviour and tissue response

Bioactive glasses are surface-active ceramic materials which support and accelerate bone growth in the body. During the healing of a bone fracture or a large bone defect, fixation is often needed. The aim of this thesis was to determine the dissolution behaviour and biocompatibility of a composite consisting of poly(ε-caprolactone-co-DL-lactide) and bioactive glass (S53P4). In addition the applicability as an injectable material straight to a bone defect was assessed. In in vitro tests the dissolution behaviour of plain copolymer and composites containing bioactive glass granules was evaluated, as well as surface reactivity and the material’s capability to form apatite in simulated body fluid (SBF). The human fibroblast proliferation was tested on materials in cell culture. In in vivo experiments, toxicological tests, material degradation and tissue reactions were tested both in subcutaneous space and in experimental bone defects. The composites containing bioactive glass formed a unified layer of apatite on their surface in SBF. The size and amount of glass granules affected the degradation of polymer matrix, as well the material’s surface reactivity. In cell culture on the test materials the human gingival fibroblasts proliferated and matured faster compared with control materials. In in vitro tests a connective tissue capsule was formed around the specimens, and became thinner in the course of time. Foreign body cell reactions in toxicological tests were mild. In experimental bone defects the specimens with a high concentration of small bioactive glass granules (<45 μm) formed a dense apatite surface layer that restricted the bone ingrowth to material. The range of large glass granules (90-315 μm) with high concentrations formed the best bonding with bone, but slow degradation on the copolymer restricted the bone growth only in the superficial layers. In these studies, the handling properties of the material proved to be good and tissue reactions were mild. The reactivity of bioactive glass was retained inside the copolymer matrix, thus enabling bone conductivity with composites. However, the copolymer was noticed to degradate too slowly compared with the bone healing. Therefore, the porosity of the material should be increased in order to improve tissue healing.

Cassava and corn starch in maltodextrin production

Maltodextrin was produced from cassava and corn starch by enzymatic hydrolysis with alpha-amylase. The cassava starch hydrolysis rate was higher than that of corn starches in maltodextrin production with shorter dextrose equivalent (DE). DE values do not show directly the nature of the obtained oligosaccharides. Maltodextrin produced from cassava and corn starch was analysed by high performance liquid chromatography (HPLC), and the analysis showed that maltodextrin production differs according to the source of the starch. This is important in defining the application of the maltodextrin, according to its desired function.

High-Performance-Tensile-Strength Alpha-Grass Reinforced Starch-Based Fully Biodegradable Composites

Though there has been a great deal of work concerning the development of natural fibers in reinforced starch-based composites, there is still more to be done. In general, cellulose fibers have lower strength than glass fibers; however, their specific strength is not far from that of fiberglass. In this work, alpha-fibers were obtained from alpha-grass through a mild cooking process. The fibers were used to reinforce a starch-based biopolymer. Composites including 5 to 35% (w/w) alpha-grass fibers in their formulation were prepared, tested, and subsequently compared with those of wood- and fiberglass-reinforced polypropylene (PP). The term “high-performance” refers to the tensile strength of the studied composites and is mainly due to a good interphase, a good dispersion of the fibers inside the matrix, and a good aspect ratio. The tensile strength of the composites showed a linear evolution for fiber contents up to 35% (w/w). The strain at break of the composites decreased with the fiber content and showed the stiffening effects of the reinforcement. The prepared composites showed high mechanical properties, even approaching those of glass fiber reinforced composites

Effect of the radiolitic sterilization in polyethylene/starch blends

Samples of LDPE/modified starch blends 80/20 m/m before and after exposure to gamma rays were examined by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction. The effect of gamma radiation is clearly seen in the samples irradiated at a dose of 25 kGy. The main alteration in the polymeric material after exposure at the radiation range was a decrease in the mechanical properties, alterations in the chemical structure of the blend with an increase in the carbonyl and vinyl indices and the appearance of new crystalline symmetry generating a crystalline domain not existing before in the blend.

Volatile compounds in the thermoplastic extrusion of bovine rumen

The volatile compounds of raw and extruded bovine rumen, extracted by dynamic headspace, were separated by gas chromatography and analyzed by GC-MS. Raw and extruded materials presented thirty-two volatile compounds. The following compounds were identified in raw bovine rumen: heptane, 1-heptene, 4-methyl-2-pentanone, toluene, hexanal, ethyl butyrate, o-xylene, m-xylene, p-xylene, heptanal, limonene, nonanal, dodecane, tridecane, tetradecane, pentadecane, hexadecane, heptadecane and octadecane. The following compounds were identified in the extruded material: 1-heptene, 2,4-dimethylhexane, toluene, limonene, undecane, tetradecane, pentadecane, hexadecane, heptadecane, octadecane and nonadecane. Mass spectra of some unidentified compounds indicated the presence of hydrocarbons with branched chains or cyclic structure.

Citric acid as multifunctional agent in blowing films of starch/PBAT

Citric acid was used as a compatibilizer in the production of starch and PBAT films plasticized with glycerol and processed by blow extrusion. Films produced were characterized by WVP, mechanical properties, FT-IR-ATR and SEM. WPV ranged from 3.71 to 12.73×10-11 g m-1 s-1 Pa-1, while tensile strength and elongation at break ranged from 1.81 to 7.15 MPa and from 8.61 to 23.63%, respectively. Increasing the citric acid concentration improved WVP and slightly decreased film resistance and elongation. The films micrographs revealed a more homogeneous material with the addition of citric acid. However, the infrared spectra revealed little about cross-linking esterification reaction