Extensometria: estudo das deformações ao redor de três implantes cone morse, com posicionamento linear, sob carga axial

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo das microdeformações geradas ao redor de implantes de hexágono interno com roscas convencionais e implantes com platôs, sob a aplicação de carga vertical

Pós-graduação em Odontologia Restauradora - ICT

Analise eletromiográfica e dinamométrica durante o ciclio da pedalada em cicloergômetro aquático

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo do comportamento biomecânico em protocolos modificados de Branemark (conceito All-on-Four): análise por extensometria linear elétrica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação, por extensometria, da deformação superficial no substrato de retenção dos implantes gerada por próteses fixas implanto suportadas em função do cantilever

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Extensometria: avaliação de implantes de sextavado externo posicionados na configuração linear e compensada (offset), sob carregamento axial

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo in vitro das micro deformações ao redor de implantes suportes de próteses parciais fixas submetidos à cargas axiais e não axiais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Use of Stress Analysis Methods to Evaluate the Biomechanics of Oral Rehabilitation With Implants

Because the biomechanical behavior of dental implants is different from that of natural tooth, clinical problems may occur. The mechanism of stress distribution and load transfer to the implant/bone interface is a critical issue affecting the success rate of implants. Therefore, the aim of this study was to conduct a brief literature review of the available stress analysis methods to study implant-supported prosthesis loading and to discuss their contributions in the biomechanical evaluation of oral rehabilitation with implants. Several studies have used experimental, analytical, and computational models by means of finite element models (FEM), photoelasticity, strain gauges and associations of these methods to evaluate the biomechanical behavior of dental implants. The FEM has been used to evaluate new components, configurations, materials, and shapes of implants. The greatest advantage of the photoelastic method is the ability to visualize the stresses in complex structures, such as oral structures, and to observe the stress patterns in the whole model, allowing the researcher to localize and quantify the stress magnitude. Strain gauges can be used to assess in vivo and in vitro stress in prostheses, implants, and teeth. Some authors use the strain gauge technique with photoelasticity or FEM techniques. These methodologies can be widely applied in dentistry, mainly in the research field. Therefore, they can guide further research and clinical studies by predicting some disadvantages and streamlining clinical time.

A MICROSTRAIN COMPARISON OF PASSIVELY FITTING SCREW-RETAINED AND CEMENTED TITANIUM FRAMEWORKS

Statement of problem. An imprecise fit between frameworks and supporting dental implants in loaded protocols increases the strain transferred to the periimplant bone, which may impair healing or generate microgaps.Purpose. The purpose of this study was to investigate the microstrain between premachined 1-piece screw-retained frameworks (group STF) and screw-retained frameworks fabricated by cementing titanium cylinders to the prefabricated framework (group CTF). This procedure was developed to correct the misfit between frameworks and loaded implants.Material and methods. Four internal hexagon cylindrical implants were placed 10 mm apart in a polyurethane block by using the surgical guides of the corresponding implant system. Previously fabricated titanium frameworks (n=10) were divided into 2 groups. In group STF, prefabricated machined frameworks were used (n=5), and, in group CTF, the frameworks were fabricated by using a passive fit procedure, which was developed to correct the misfit between the cast titanium frameworks and supporting dental implants (n=5). Both groups were screw-retained under torque control (10 Ncm). Six strain gauges were placed on the upper surface of the polyurethane block, and 3 strain measurements were recorded for each framework. Data were analyzed with the Student t test (alpha=.05).Results. The mean microstrain values between the framework and the implants were significantly higher for group STF (2517 me) than for group CTF (844 me) (P<.05).Conclusions. Complete-arch implant frameworks designed for load application and fabricated by using the passive fit procedure decreased the strain between the frameworks and implants more than 1 piece prefabricated machined frameworks.

Extensometria: estudo das microdeformações ao redor de três implantes de hexágono interno, com posicionamento linear, sob a influência da fundição de coifas plásticas e usinadas

The objective of this in vitro study was quantify the micro strain development around the internal hexagon implants, varying the type of prosthetic coping. For This reason, three implants of internal hexagon were inserted into one polyurethane block in line placement. Microunit abutments were screwed onto the implants. Tangentially the implants were bonded the strain gauges, two to the center implant. Ten structures, each one containing three copings were cast in Co-Cr alloy, that were divided into groups in the first group, plastic copings were used, and in the second group machined copings were used. The superstructure’s occlusal screws were tightened onto Microunit abutments with 10 Ncm torque, the magnitude of micro strain was recorded. The mean values of each strain gauge of each plastic copings were 363,37 ± 237,66 and the machined copings were 338,12 ± 223,01. The data were analyzed statistically by t- Student test. No statistically significant difference was found between the prosthetic copings (p= 0,867). It was concluded that to internal hexagon implants in line placement, the type of copings presented similar magnitude of micro strain after prosthetic occlusal screw was tightened

Análise das microdeformações geradas ao redor de implantes de hexágono externo sob a aplicação de cargas verticais em pilares microunit retos e angulados

Pós-graduação em Odontologia Restauradora - ICT

Avaliação in vitro das microdeformações em implantes curtos, com conexão protética cone morse e diferentes desenhos de roscas, convencionais e platôs

Pós-graduação em Odontologia Restauradora - ICT

Estudo das microdeformações geradas ao redor de implantes de hexágono externo, sob a aplicação de cargas axiais e não axiais em pilares protéticos retos e angulados

Pós-graduação em Odontologia Restauradora - ICT

Caracterização biomecânica da conduta motora remada básica de passeio do esporte stand up paddle

Pós-graduação em Engenharia Mecânica - FEG

Effect of framework soldering on the deformation of implant abutments after framework seating

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)