Use of spent compost in the cultivation of Agaricus blazei

Two compost formulations, based on Braquiaria straw (Brachiaria sp.), a conventional one and a spent one, were tested in the cultivation of ABL 99/30 and ABL 04/49 strains of Agaricus blazei. The experimental design was in a completely randomized factorial scheme with four treatments (two strains of A. blazei x two types of compost) and 30 repetitions. Each experimental unit consisted of a box with 10 to 10.5 kg of moist fresh compost. According to the results obtained, the loss of organic matter of the composts was affected by the A. blazei strain and the type of compost used. The traditional compost lost a higher organic matter content compared to the spent compost, and the ABL 99/30 strain caused a higher loss of organic matter in the composts compared to the ABL 04/49 strain. Yield, biological efficiency, mass and number of basidiomata produced were similar between the conventional and the spent compost, as well as the chemical analysis of the produced basidiomata. However, the A. blazei strains showed some differences among each other, the basidiomata of strain ABL 04/49 obtained a higher percentage of crude protein in their composition, compared to the ABL 99/30, in both composts. Thus, the utilization of spent compost in the cultivation of A. blazei did not impair the basidiomata yield nor their nutritional value, demonstrating it to be a good option to be used as an ingredient in the compost formulation for the A. blazei cultivation.

Gamma irradiation can control the number of psychotrophic bacteria in Agaricus bisporus during storage

We evaluated the effect of gamma irradiation doses (0, 125, 250, and 500 Gy) in control of psychrotrophic bacteria in different strains of Agaricus bisporus (ABI-07/06, ABI-05/03, and PB-1) during storage, cultivated in composts based on oat straw (Avena sativa) and Brachiaria spp. The experimental design was completely randomized in a factorial scheme 4  2  3 (irradiation doses  composts  strains), with 24 treatments, each consisting of 2 replicates, totaling 48 experimental units (samples of mushrooms). The mushrooms collected from all culture conditions were packaged in plastic polypropylene with 200 g each and subjected to Cobalt-60 irradiator, type Gammacell 220, and dose rate 0.740 kGy h–1 , according to the treatments. Subsequently, the control (nonirradiated) and other treatments were maintained at 4 ± 1°C and 90% relative humidity (RH) in a climatic chamber to perform the microbiological analysis of mushrooms on the 1st and 14th day of storage. According to the results, it was found that the highest mean colony psychotrophic count, after 14 days of storage, was observed in strain ABI-07/06 1.30 × 108 g -1 most probable number (MPN) in nonirradiated mushrooms, coming from Brachiaria grass-based compost, and this same strain under the same storage conditions, coming from the same type of compost that underwent a dose of 500 Gy, obtained a significant reduction in mean colonies of psychrotrophic bacteria (2.25 × 104 g –1 MPN). Thus, the irradiation doses tested favored reducing the number of colonies of psychrotrophic bacteria, regardless of the type of compound and strain of A. bisporus.

Extractos de residuos de la vitivinicultura : concentración de polifenoles

El objetivo del trabajo fue determinar la concentración de polifenoles en extractos de hojas de verano y otoño y de escobajo de variedades tintas de vitis vinifera, obtenidos por distintos métodos.Se trabajó con hojas de verano y de otoño de variedad Syrah y con hojas de otoño variedad Malbec, dividiéndolas por su color en rojas y amarillas, y con escobajo de variedad Malbec. Los extractos se obtuvieron por maceración en agua y baño María hirviente durante tres horas (BM), maceración en agua y agitación, a temperatura ambiente, durante 48 horas (AG). Se utilizó como referencia oleorresina de romero. El orden decreciente respecto de la cantidad de polifenoles expresados en g de quercitina / g de extracto seco fue el siguiente: oleorresina de romero: 56,3 ± 0,3 extracto de: hojas de otoño Syrah por maceración y agitación en agua a temperatura ambiente durante 48 horas: 7,5 ± 0,3; escobajo Malbec por maceración y agitación en agua a temperatura ambiente durante 48 horas: 24 ± 0,3; hojas de otoño rojas Malbec por maceración y agitación en agua a temperatura ambiente durante 48 horas: 22 ± 0,3; escobajo de Malbec: a baño María 21,4 ± 0,3; hojas de otoño Syrah 3 horas a baño María: 21,1 ±0,3; hojas de otoño amarillas Malbec por maceración y agitación en agua a temperatura ambiente durante 48 horas: 17 ± 0,3; hojas de verano Syrah 3 horas a baño María: 16,5 ± 0,3; hojas de otoño rojas Malbec 3 horas a baño María: 13,8 ± 0,3; hojas de otoño amarillas Malbec 3 horas a baño María: 12,4 ± 0,3; hojas de verano Syrah por maceración y agitación en agua a temperatura ambiente durante 48 horas: 12,2 ± 0,3. Se concluyó que las hojas de otoño contienen mayor cantidad de polifenoles que las de verano; la variedad Syrah posee más polifenoles en hojas que la variedad Malbec; el escobajo de Malbec contiene más olifenoles que las hojas de la misma variedad; y el mejor método de extracción para obtener estos compuestos activos fue por maceración en agua y agitación a temperatura ambiente durante 48 horas.

Compostabilidad de envases de bolsas de PBAT+PLA y envases rígidos de PLA mediante tecnologías de pila y túnel

Los polímeros compostables suponen en torno al 30% de los bioplásticos destinados a envasado, siendo a su vez esta aplicación el principal destino de la producción de este tipo de materiales que, en el año 2013, superó 1,6 millones de toneladas. La presente tesis aborda la biodegradación de los residuos de envases domésticos compostables en medio aerobio para dos tipos de formato y materiales, envase rígido de PLA (Clase I) y dos tipos de bolsas de PBAT+PLA (Clases II y III). Sobre esta materia se han realizado diversos estudios en escala de laboratorio pero para otro tipo de envases y biopolímeros y bajo condiciones controladas del compost con alguna proyección particularizada en plantas. La presente tesis da un paso más e investiga el comportamiento real de los envases plásticos compostables en la práctica del compostaje en tecnologías de pila y túnel, tanto a escala piloto como industrial, dentro del procedimiento y con las condiciones ambientales de instalaciones concretas. Para ello, con el método seguido, se han analizado los requisitos básicos que debe cumplir un envase compostable, según la norma UNE – EN 13432, evaluando el porcentaje de biodegradación de los envases objeto de estudio, en función de la pérdida de peso seco tras el proceso de compostaje, y la calidad del compost obtenido, mediante análisis físico-químico y de fitotoxicidad para comprobar que los materiales de estudio no aportan toxicidad. En cuanto a los niveles de biodegrabilidad, los resultados permiten concluir que los envases de Clase I se compostan adecuadamente en ambas tecnologías y que no requieren de unas condiciones de proceso muy exigentes para alcanzar niveles de biodegradación del 100%. En relación a los envases de Clase II, se puede asumir que se trata de un material que se composta adecuadamente en pila y túnel industrial pero que requiere de condiciones exigentes para alcanzar niveles de biodegradación del 100% al afectarle de forma clara la ubicación de las muestras en la masa a compostar, especialmente en el caso de la tecnología de túnel. Mientras el 90% de las muestras alcanza el 100% de biodegradación en pila industrial, tan sólo el 50% lo consigue en la tecnología de túnel a la misma escala. En cuanto a los envases de Clase III, se puede afirmar que es un material que se composta adecuadamente en túnel industrial pero que requiere de condiciones de cierta exigencia para alcanzar niveles de biodegradación del 100% al poderle afectar la ubicación de las muestras en la masa a compostar. El 75% de las muestras ensayadas en túnel a escala industrial alcanzan el 100% de biodegradación y, aunque no se ha ensayado este tipo de envase en la tecnología de pila al no disponer de muestras, cabe pensar que los resultados de biodegrabilidad que hubiera podido alcanzar habrían sido, como mínimo, los obtenidos para los envases de Clase II, al tratarse de materiales muy similares en composición. Por último, se concluye que la tecnología de pila es más adecuada para conseguir niveles de biodegradación superiores en los envases tipo bolsa de PBAT+PLA. Los resultados obtenidos permiten también sacar en conclusión que, en el diseño de instalaciones de compostaje para el tratamiento de la fracción orgánica recogida selectivamente, sería conveniente realizar una recirculación del rechazo del afino del material compostado para aumentar la probabilidad de someter este tipo de materiales a las condiciones ambientales adecuadas. Si además se realiza un triturado del residuo a la entrada del proceso, también se aumentaría la superficie específica a entrar en contacto con la masa de materia orgánica y por tanto se favorecerían las condiciones de biodegradación. En cuanto a la calidad del compost obtenido en los ensayos, los resultados de los análisis físico – químicos y de fitotoxicidad revelan que los niveles de concentración de microorganismo patógenos y de metales pesados superan, en la práctica totalidad de las muestras, los niveles máximos permitidos en la legislación vigente aplicable a productos fertilizantes elaborados con residuos. Mediante el análisis de la composición de los envases ensayados se constata que la causa de esta contaminación reside en la materia orgánica utilizada para compostar en los ensayos, procedente del residuo de origen doméstico de la denominada “fracción resto”. Esta conclusión confirma la necesidad de realizar una recogida selectiva de la fracción orgánica en origen, existiendo estudios que evidencian la mejora de la calidad del residuo recogido en la denominada “fracción orgánica recogida selectivamente” (FORM). Compostable polymers are approximately 30% of bioplastics used for packaging, being this application, at same time, the main destination for the production of such materials exceeded 1.6 million tonnes in 2013. This thesis deals with the biodegradation of household packaging waste compostable in aerobic medium for two format types and materials, rigid container made of PLA (Class I) and two types of bags made of PBAT + PLA (Classes II and III). There are several studies developed about this issue at laboratory scale but for other kinds of packaging and biopolymers and under composting controlled conditions with some specifically plants projection. This thesis goes one step further and researches the real behaviour of compostable plastic packaging in the composting practice in pile and tunnel technologies, both at pilot and industrial scale, within the procedure and environmental conditions of concrete devices. Therefore, with a followed method, basic requirements fulfilment for compostable packaging have been analysed according to UNE-EN 13432 standard. It has been assessed the biodegradability percentage of the packaging studied, based on loss dry weight after the composting process, and the quality of the compost obtained, based on physical-chemical analysis to check no toxicity provided by the studied materials. Regarding biodegradability levels, results allow to conclude that Class I packaging are composted properly in both technologies and do not require high exigent process conditions for achieving 100% biodegradability levels. Related to Class II packaging, it can be assumed that it is a material that composts properly in pile and tunnel at industrial scale but requires exigent conditions for achieving 100% biodegradability levels for being clearly affected by sample location in the composting mass, especially in tunnel technology case. While 90% of the samples reach 100% of biodegradation in pile at industrial scale, only 50% achieve it in tunnel technology at the same scale. Regarding Class III packaging, it can be said that it is a material properly composted in tunnel at industrial scale but requires certain exigent conditions for reaching 100% biodegradation levels for being possibly affected by sample location in the composting mass. The 75% of the samples tested in tunnel at industrial scale reaches 100% biodegradation. Although this kind of packaging has not been tested on pile technology due to unavailability of samples, it is judged that biodegradability results that could be reached would have been, at least, the same obtained for Class II packaging, as they are very similar materials in composition. Finally, it is concluded that pile technology is more suitable for achieving highest biodegradation levels in bag packaging type of PBAT+PLA. Additionally, the obtained results conclude that, in the designing of composting devices for treatment of organic fraction selectively collected, it would be recommended a recirculation of the refining refuse of composted material in order to increase the probability of such materials to expose to proper environmental conditions. If the waste is grinded before entering the process, the specific surface in contact with organic material would also be increased and therefore biodegradation conditions would be more favourable. Regarding quality of the compost obtained in the tests, physical-chemical and phytotoxicity analysis results reveal that pathogen microorganism and heavy metals concentrations exceed, in most of the samples, the maximum allowed levels by current legislation for fertilizers obtained from wastes. Composition analysis of tested packaging verifies that the reason for this contamination is the organic material used for composting tests, comes from the household waste called “rest fraction”. This conclusion confirms the need of a selective collection of organic fraction in the origin, as existing studies show the quality improvement of the waste collected in the so-called “organic fraction selectively collected” (FORM).

Trichloroethylene fate and transport studies and biodegradation kinetics in the saturated zone

Permeable reactive barriers (PRB) are constructed from soil solid amendments to support the growth of bacteria that are capable of degrading organic contaminants. The objective of this study was to identify low-cost soil solid amendments that could retard the movement of trichloroethylene (TCE) while serving as long-lived carbon sources to foster its biodegradation in shallow groundwater through the use of a PRB. The natural amendments high in organic carbon content such as eucalyptus mulch, compost, wetland peat, organic humus were compared based on their geophysical characteristics, such as pHw, porosity and total organic carbon (TOC), and as well as TCE sorption potentials. The pHw values were within neutral range except for pine bark mulch and wetland peat. All other geophysical characteristics of the amendments showed suitability for use in a PRB. While the Freundlich model showed better fit for compost and pine bark mulch, the linear sorption model was adequate for eucalyptus mulch, wetland peat and Everglades muck within the concentration range studied (0.2-0.8 mg/L TCE). According to these results, two composts and eucalyptus mulch were selected for laboratory column experiments to evaluate their effectiveness at creating and maintaining conditions suitable for TCE anaerobic dechlorination. The columns were monitored for pH, ORP, TCE degradation, longevity of nutrients and soluble TOC to support TCE dechlorination. Native bacteria in the columns had the ability to convert TCE to DCEs; however, the inoculation with the TCE-degrading culture greatly increased the rate of biodegradation. This caused a significant increase in by-product concentration, mostly in the form of DCEs and VC followed by a slow degradation to ethylene. Of the tested amendments eucalyptus mulch was the most effective at supporting the TCE dechlorination. The experimental results of TCE sequential dechlorination took place in eucalyptus mulch and commercial compost from Savannah River Site columns were then simulated using the Hydrus-1D model. The simulations showed good fit with the experimental data. The results suggested that sorption and degradation were the dominant fate and transport mechanisms for TCE and DCEs in the column, supporting the use of these amendments in a permeable reactive barrier to remediate the TCE.

Cultivo de microalgas utilizando pentoses como fonte de carbono

As microalgas podem ser consideradas como um dos mais eficientes sistemas biológicos de transformação de energia solar em compostos orgânicos. Quando cultivadas em meios adequados, certas espécies podem duplicar sua biomassa diariamente. Além disso, possuem inúmeras vantagens, como: elevada velocidade de crescimento; potencial para absorver CO2, reduzindo assim a quantidade de emissões deste gás na atmosfera e diminuindo o efeito estufa. O objetivo do trabalho foi estudar o efeito do uso de pentoses no cultivo de Chlorella minutissima, Chlorella vulgaris, Chlorella homosphaera, Dunaliella salina, Spirulina paracas e Synechococcus nidulans, avaliando o perfil cinético do crescimento e a capacidade de produção de carboidratos e proteínas. Para o cultivo das microalgas foram utilizados os meios: Zarrouk, Bristol`S Modificado e DUN. Em todos os meios o componente nitrogenado foi reduzido pela metade e utilizado 1%, 5%, 10%, 20% e 30% de pentoses, com concentrações de xilose e arabinose que representassem as mesmas presentes em caldo hidrolisado do bagaço de cana de açúcar pré-tratado. Os cultivos foram realizados em fotobiorreatores de 2 L, mantidos em estufa a 30 ºC, fotoperíodo de 12h claro/escuro e 2500 Lx, com agitação a uma vazão de 0,75 v.v.m. . O crescimento de biomassa foi monitorado diariamente pela densidade ótica das culturas em espectrofotômetro a 670nm. Foram avaliados parâmetros cinéticos como a concentração máxima de biomassa, produtividade máxima e velocidade específica máxima de crescimento. A determinação do consumo das pentoses foi realizada através da metodologia de Somogy e Nelson, para a determinação de carboidratos foi utilizada uma adaptação do método do ácido 3,5 dinitro salicílico, as proteínas foram quantificadas pelo método de micro-Kjeldahl. Todas as microalgas foram capazes de consumir em no máximo quatro dias as concentrações de pentoses, e logo após esta etapa mixotrófica manter-se em crescimento autotrófico, destacando-se as cepas de Dunaliella salina e Synechococcus nidulans que esgotaram as maiores concentrações utililizadas em dois dias de cultivo. Para as cianobactérias estudadas, Spirulina paracas cultivada com 10% de C5, foi a que obteve os melhores resultados de concentração celular, produtividade e velocidade específica de crescimento máxima, 1,364 g.L-1 , 0,128 g.L-1 .dia-1 e 0,240 dia-1 . Em relação ao efeito na composição da biomassa, Synechococcus nidulans produziu o maior teor de proteínas, 62,9%, nos ensaios com 10% de C5. Já as cepas de Chlorophytas os melhores resultados foram obtidos com o uso de 5% de C5, para os parâmetros cinéticos destacam-se os valores encontrados para Dunaliella salina, onde a maior concentração de biomassa, produtividade e velocidade específica de crescimento foram 1,246 g.L-1 , 0,091 g.L- 1 .dia-1 e 0,379 dia-1 , respectivamente. Chlorella minutissima e Dunaliella salina foram as melhores produtoras de carboidratos, alcançando 58,6%/0,3 g.L-1 e 23,07%/0,29 g.L-1 ,respecivamente. Logo, o uso de pentoses nas microalgas em substituição as fontes tradicionais de carbono, resultou no crescimento das mesmas, o que mostra que estas podem agir como intermediários para a absorção de açúcares de cinco carbonos.

Valorização de resíduos provenientes da atividade no setor avícola: aplicação do processo de compostagem

O setor avícola, como setor em constante crescimento está associado à produção de elevadas quantidades de resíduos sólidos orgânicos. A crescente taxa de produção de resíduos avícolas leva à necessidade de lhes dar um destino adequado podendo a valorização orgânica, nomeadamente a compostagem, ser uma opção. O presente estudo pretende dar um contributo para o projeto de uma unidade de compostagem numa empresa portuguesa do setor, com valorização dos resíduos produzidos pela mesma, avaliando o potencial de aplicação desta operação de tratamento de resíduos e a qualidade do produto final. Como primeiro passo foi realizada uma caracterização dos resíduos a utilizar de forma a perceber a sua possível influência no processo de degradação. Os ensaios de compostagem foram realizados à escala laboratorial, numa gama de temperatura de 50 a 55ᵒC, utilizando como substrato base uma mistura dos resíduos avícolas, de acordo com os seus quantitativos de produção. Vários potenciais agentes estruturantes foram também testados, como adição ao substrato. A monitorização do processo foi feita com base em análises das fases gasosa (gases de exaustão), sólida (substrato em decomposição) e líquida (lixiviado). A avaliação do processo foi ainda complementada com a caracterização dos produtos finais obtidos, os quais foram ainda sujeitos a testes de fitotoxicidade. Foram observados graus de conversão de matéria orgânica relativamente altos (40-50%), comprovando a aplicabilidade desta operação de tratamento de resíduos. Embora a diferença entre ensaios tenha sido pouco notória, a utilização de uma combinação de cama de aviário e mato destroçado e compostado aparenta ser ligeiramente mais eficiente, enquanto a utilização de casca de eucalipto produziu os piores resultados. Perdas de humidade e de azoto foram as duas situações mais críticas observadas para os vários ensaios, tendo influência tanto sobre o processo como sobre o produto final. Os compostos obtidos revelam baixa qualidade, exibindo valores elevados de pH e condutividade elétrica e elevadas concentrações de metais pesados, tais como cobre e zinco. Supõe-se que as características adversas verificadas estejam associadas à aplicação de quantidades demasiado elevadas de cinza nos substratos, levando à necessidade de redução deste material; estudos adicionais seriam necessários a fim de avaliar as possibilidades de ajuste das quantidades a utilizar, dos diferentes materiais, com o intuito de produzir um produto final com qualidade, respeitando os requisitos legais.

EFFECT OF COMPOST ON THE MICROCLOVER ESTABLISHMENT AND USE OF COMPOST AND MICROCLOVER TO REDUCE LAWN NUTRIENT RUNOFF

High volume compost incorporation can reduce runoff from compacted soils but its use also associated with elevated N and P concentrations in runoff making it difficult to assess if this practice will reduce nutrient loading of surface waters. Additionally, little is known about how this practice will effect leguminous species establishment in lawns as means to reduce long term fertilizer use. When 5 cm of compost was incorporated into soil a reduction in runoff of 40 and 59% was needed for N and P losses from a tall fescue + microclover lawn to be equivalent to a non-compost amended soil supporting a well fertilized tall fescue lawn. Use of compost as a soil amendment resulted in quicker lawn establishment and darker color, when compared to non-amended soil receiving a mineral fertilizer. Biosolid composts containing high amounts ammonium severely reduce the establishment of clover in tall fescue + micrclover seed mixture.

Síntese e caracterização de nanocompósitos de carbon-dot e lantanídeos

Dissertação (mestrado)—Universidade de Brasília, Instituto de Química, 2015.

Effect of diazotrophic bacterium inoculation and organic fertilization on yield of Champaka pineapple intercropped with irrigated sapota.

The purpose of this study was to evaluate the response of the Champaka pineapple to inoculation with the diazotrophic bacterium Asaia bogorensis (strain 219) when grown with organic fertilizer in an irrigated sapota orchard. Plantlets were transplanted to tubes containing a mixture of worm compost and vermiculite and inoculated with 108 bacterial cells. After five and a half months of acclimatization the plantlets were transplanted in furrows in the sapota orchard. Fertilizer was placed at the bottom of the furrows and covered with three doses (2.5; 5.0 and 7.5 L linear m−1 row) of three organic composts. The successful association of the plantlets with the diazo-trophic bacterium was confirmed by most probable number analysis before transferring to the field. Plants inoculated with strain AB219 showed the greatest initial leaf growth and produced the heaviest fruits compared to uninoculated plants. Plant growth and fruit yield increased with increasing compost dosages. The results suggested that Champaka pineapple benefited from the association of A. bogorensis (strain 219) when grown under irrigation and with organic fertilizer.

Composting of different agro-food wastes: Effects of the phenolic and lignocellulosic fractions on greenhouse gases emissions

Currently, society faces a number of challenges related to the large amounts of organic wastes generated and accumulated by the increasing expansion of agroindustrial activities1. Most of these wastes are rich in lignocellulosic compounds, which represents a major fraction of all plant biomass (of above 90%), so, its degradation is crucial for global carbon cycle2. These organic wastes may be introduced directly on agriculture sector as soil organic amendment, however, these might contain phytochemicals, such as phenolic compounds which may introduce toxic effects to soil and to beneficial organisms. Transformation and degradation of these renewable organic wastes into composts (COMPOSTING) is a possible solution for these problems and an environmentally friendly processes that allows make use of natural resources efficiently3. The main potential handicap is generation and emission of greenhouse gases such as carbon dioxide (CO2 ), methane (CH4 ) and nitrous oxide (N2O) and another ones which may led serious problems like nitric oxide (NO) and ammonia (NH3) 4. For this reason, quantification of GHG emissions from composting and finding possible relations with the chemical and structural composition of the wastes used is crucial to the development of technologies for mitigating emissions and should help to make decisions concerning waste management.

Co-Composting of Poultry Manure with Different Organic Amendments

To study the influence of different organic amendments on the quality of poultry manure compost, three pilot composting trials were carried out with different mixes: poultrymanure/carcasse meal/ashes/grape pomace (Pile 1), poultry manure/cellulosic sludge (Pile 2) and poultry manure (Pile 3). For all piles, wood chips were applied as bulking agent. The process was monitored, over time, by evaluating standard physical and chemical parameters, such as, pH, electric conductivity, moisture, organic matter and ash content, total carbon and total nitrogen content, carbon/nitrogen ratio (C/N) and content in mineral elements. Piles 1 and 2 reached a thermophilic phase, however having different trends. Pile 1 reached this phase earlier than Pile 2. For both, the pH showed a slight alkaline character and the electric conductivity was lower than 2 mS/cm. Also, the initial C/N value was 22 and reached values lower than 15 at the end of composting process. The total N content of the Pile 1 increased slightly during composting, in contrast with the others piles. At the end of composting process, the phosphorus content ranged between 54 and 236 mg/kg dry matter, for Pile 2 and 3, respectively. Generally, the Piles 1 and 3 exhibited similar heavy metals content. This study showed that organic amendments can be used as carbon source, given that the final composts presented parameters within the range of those recommended in the 2nd Draft of EU regulation proposal (DG Env.A.2 2001) for compost quality.