Preparation of a novel polysulfone/polyethylene oxide/silicone rubber multilayer composite membrane for hydrogen-nitrogen separation

A novel poly sulfone/polyethylene oxide/silicone rubber (PSOPEO/SR) multilayer composite membrane was fabricated by double coating polysulfone substrate membrane with polyethylene oxide and silicone rubber. Gas permeation experiments were performed at 30 degrees C for hydrogen and nitrogen. PSf(PEO/SR membrane displayed high and steady performance for H-2/N-2: permeances of H-2 and N-2 of 49.51 and 0.601 GPU, respectively, and H-2/N-2 ideal separation factor of 82.3. It was explained that layer interfaces due to the introduction of PEO layer act as the permselective media and are responsible for the higher H-2/N-2 ideal separation factor which has exceeded the intrinsic permselectivities of the three polymers used in this study. (c) 2005 Elsevier B.V. All rights reserved.

Subset Warping: Rubber Sheeting with Cuts

Image warping, often referred to as "rubber sheeting" represents the deformation of a domain image space into a range image space. In this paper, a technique is described which extends the definition of a rubber-sheet transformation to allow a polygonal region to be warped into one or more subsets of itself, where the subsets may be multiply connected. To do this, it constructs a set of "slits" in the domain image, which correspond to discontinuities in the range image, using a technique based on generalized Voronoi diagrams. The concept of medial axis is extended to describe inner and outer medial contours of a polygon. Polygonal regions are decomposed into annular subregions, and path homotopies are introduced to describe the annular subregions. These constructions motivate the definition of a ladder, which guides the construction of grid point pairs necessary to effect the warp itself.

Replacing rubber plantations by rain forest in Southwest China - Who would gain and how much?

The cultivation of rubber trees in Xishuangbanna Prefecture in China’s Yunnan Province has triggered an unprecedented economic development but it is also associated with severe environmental problems. Rubber plantations are encroaching the indigenous rainforests at a large scale and a high speed in Xishuangbanna. Many rare plant and animal species are endangered by this development, the natural water management is disturbed and even the microclimate in this region has changed over the past years. The present study aims at an assessment of the environmental benefits accruing from a reforestation project partly reversing the deforestation that has taken place over the past years. To this end a Contingent Valuation survey has been conducted in Xishuangbanna to elicit local residents’ willingness to pay for this reforestation program that converts existing rubber plantations back into forest. It is shown that local people's awareness of the environmental problems caused by increasing rubber plantation is quite high and that in spite of the economic advantages of rubber plantation there is a positive willingness among the local population to contribute financially to a reduction of existing rubber plantations for the sake of a partial restoration of the local rainforest. These results could be used for the practical implementation of a PES (Payments for Eco-System Services) system for reforestation in Xishuangbanna.

Correlating Additives to Deterioration and Assessing the Effectiveness of Acrylic Coatings for the Protection of Rubber

Conservators have long been aware of the problems associated with the preservation of rubber objects due to inherent instability that can be attributed, in part, to the presence of additives. Inorganic additives, such as fillers, accelerators, stabilizers, and special ingredients are necessary in manufacturing to alter the properties of natural rubber. These materials all have different interactions with the rubber, and each other, and differing effects on the ageing process. To date, the most effective and accepted methods to preserve rubber are cold, dark storage of objects, or the use of low oxygen environments. While these methods are effective, they greatly limit access. The application of coatings to the surface of rubber objects can slow deterioration and greatly increase the ability of an institution to handle and display rubber objects. While numerous coatings for preventive and interventive treatment have been tested, none have been so successful to warrant routine use. The first section of this research highlighted the relationship between the inclusion of certain additives in natural rubber objects and the accelerated or slowed down overall degradation. In the second part of this research, the acrylic varnishes Golden Polymer Varnish with UVLS, Lascaux Acrylic Transparent Varnish-UV, Sennelier Matte Lacquer with UV Protection, and Liquitex Soluvar Varnish containing ultraviolet light absorbers or stabilizers were tested as a preventative coating for rubber. Through testing the visual and physical properties of the samples, as well as compound analysis the results of this research suggest that acrylic varnishes do provide protection, each to varying degrees. The results also provided insight into the behavior of rubber and these varnishes with continuing light exposure.

Adsorption of Ni(SO4) on Malaysian rubber-wood ash

The possible use of wood ash as an adsorbent of nickel sulphate from dilute solutions and the effect of operating parameters were investigated in this study. The rate constants of adsorption were determined at different concentrations and temperatures. The applicability of the first-order reversible equation and an empirical kinetic model were tested to understand the kinetics of nickel sulphate removal at different concentrations. Pore diffusion was found as the rate-controlling step. The Langmuir and Freundlich isotherms were applied to find out the adsorption parameters. The activation energy of adsorption was -11.54 kJ mol-1. The value of the enthalpy change was ?H=-10.35 kcal mol-1.

Clarification of rubber mill wastewater by a plant based biopolymer- comparison with common inorganic coagulants

Background: In this study, the efficiency of Guar gum as a biopolymer has been compared with two other widely used inorganic coagulants, ferric chloride (FeCl3) and aluminum chloride (AlCl3), for the treatment of effluent collected from the rubber-washing tanks of a rubber concentrate factory. Settling velocity distribution curves were plotted to demonstrate the flocculating effect of FeCl3, AlCl3 and Guar gum. FeCl3 and AlCl3 displayed better turbidity removal than Guar gum at all settling velocities.

Result: FeCl3, AlCl3 and Guar gum removed 92.8%, 88.2% and 88.1% turbidity, respectively, of raw wastewater at a settling velocity of 0.1 cm min-1, respectively. Scanning electron microscopic (SEM) study conducted on the flocs revealed that Guar gum and FeCl3produced strong intercoiled honeycomb patterned floc structure capable of entrapping suspended particulate matter. Statistical experimental design Response Surface Methodology (RSM) was used to design all experiments, where the type and dosage of flocculant, pH and mixing speed were taken as control factors and, an optimum operational setting was proposed.

Conclusion: Due to biodegradability issues, the use of Guar gum as a flocculating agent for wastewater treatment in industry is highly recommended.

The ageing behaviour of hydrogenated nitrile butadiene rubber/nanoclay nanocomposites in various mediums

Hydrogenated nitrile butadiene rubber (HNBR) nanocomposites were prepared using commercially available organoclays (Cloisite 15A). The main focus of the current investigation is to study the influence of the organoclay reinforced in HNBR after subjecting it to long-term oxidative ageing and immersion studies. All the different nanoclay nanocomposites were air aged for a period of 168 h and at 150°C. The changes in the mechanical properties such as tensile strength and elongation at break have been compared with respect to the control sample. For immersion tests, three different liquid mediums were considered for this current investigation. All the samples were immersed in different mediums for a period of 168 h at 150°C. The changes in the swelling index and the mechanical properties have been reported with respect to the control sample. After reinforcing nanoclays into HNBR there was good resistance to swelling in all the three different liquid mediums in comparison to control sample. Tensile testing was performed on the immersed nanocomposites to evaluate the mechanical behaviour after immersion studies. A probable mechanism behind the improved performance has been suggested. © The Author(s) 2012.

Influence of nanoclays on mechanical and barrier properties of hydrogenated acrylonitrile butadiene rubber nanocomposites

In this research, two different methods have been investigated for optimising the preparation of hydrogenated acrylonitrile butadiene rubber/clay nanocomposites. Commercially available organoclay (Cloisite 20A) has been considered for the preparation of rubber nanocomposites. A detailed analysis has been made to investigate the morphological structure and mechanical behaviour at room temperature and at elevated temperature. Also the influence of organoclays on permeability has been studied. Structural analysis indicates very good dispersion for a low loading of 5 parts per hundred (phr) amount of nanoclays. Significant improvements in mechanical properties have been observed with the addition of organoclays at both room and elevated temperatures. Even with the low level of addition of nanoclays, there was a remarkable reduction in permeability. © Institute of Materials, Minerals and Mining 2011.

Design of an automated solar concentrator for the pyrolysis of scrap rubber

An automated solar reactor system was designed and built to carry out catalytic pyrolysis of scrap rubber tires at 550°C. To maximize solar energy concentration, a two degrees-of-freedom automated sun tracking system was developed and implemented. Both the azimuth and zenith angles were controlled via feedback from six photo-resistors positioned on a Fresnel lens. The pyrolysis of rubber tires was tested with the presence of two types of acidic catalysts, H-beta and H-USY. Additionally, a photoactive TiO<inf>2</inf> catalyst was used and the products were compared in terms of gas yields and composition. The catalysts were characterized by BET analysis and the pyrolysis gases and liquids were analyzed using GC-MS. The oil and gas yields were relatively high with the highest gas yield reaching 32.8% with H-beta catalyst while TiO<inf>2</inf> gave the same results as thermal pyrolysis without any catalyst. In the presence of zeolites, the dominant gasoline-like components in the gas were propene and cyclobutene. The TiO<inf>2</inf> and non-catalytic experiments produced a gas containing gasoline-like products of mainly isoprene (76.4% and 88.4% respectively). As for the liquids they were composed of numerous components spread over a wide distribution of C<inf>10</inf> to C<inf>29</inf> hydrocarbons of naphthalene and cyclohexane/ene derivatives.

Control of wild rubber extraction in the forests of northeast India, 1850-1880

This paper uses the history of rubber extraction to explore competing attempts to control the forest environments of Assam and beyond in the second half of the nineteenth century. Forest communities faced rival efforts at environmental control from both European and Indian traders, as well as from various centres of authority within the Raj. Government attempts to regulate rubber collection were undermined by the weak authority of the Raj in these regions, leading to widespread smuggling. Partly in response to the disruptive influence of rubber traders on the frontier, the Raj began to restrict the presence of outsiders in tribal regions, which came to be understood as distinct areas outside British control. When rubber yields from the forests nearest the Brahmaputra fell in the wake of intensive exploitation, India's scientific foresters demanded and from 1870 obtained the ability to regulate the Assamese forests, blaming indigenous rubber tapping strategies for the declining yields and arguing that Indian rubber could be ‘equal [to] if not better' than Amazonian rubber if only tappers would change their practices. The knowledge of the scientific foresters was fundamentally flawed, however, and their efforts to establish a new type of tapping practice failed. By 1880, the government had largely abandoned attempts to regulate wild Indian rubber, though wild sources continued to dominate the supply of global rubber until after 1910.

Formulation of emulsion systems for the preparation of butyl rubber gloves

Mémoire numérisé par la Division de la gestion de documents et des archives de l'Université de Montréal