Control of an underactuated-slender-hull unmanned underwater vehicle using Port-Hamiltonian theory

This paper presents a control design for tracking of attitude and speed of an underactuated slender-hull unmanned underwater vehicle (UUV). The control design is based on Port-Hamiltonian theory. The target dynamics (desired dynamic response) is shaped with particular attention to the target mass matrix so that the influence of the unactuated dynamics on the controlled system is suppressed. This results in achievable dynamics independent of uncontrolled states. Throughout the design, insight of the physical phenomena involved is used to propose the desired target dynamics. The performance of the design is demonstrated through simulation with a high-fidelity model.

Modeling and control of a robotic power line inspection vehicle

Power line inspection is a vital function for electricity supply companies but it involves labor-intensive and expensive procedures which are tedious and error-prone for humans to perform. A possible solution is to use an unmanned aerial vehicle (UAV) equipped with video surveillance equipment to perform the inspection. This paper considers how a small, electrically driven rotorcraft conceived for this application could be controlled by visually tracking the overhead supply lines. A dynamic model for a ducted-fan rotorcraft is presented and used to control the action of an Air Vehicle Simulator (AVS), consisting of a cable-array robot. Results show how visual data can be used to determine, and hence regulate in closed loop, the simulated vehicle’s position relative to the overhead lines.

Autonomous bathymetry for risk assessment with ROAZ robotic surface vehicle

The use of unmanned marine robotic vehicles in bathymetric surveys is discussed. This paper presents recent results in autonomous bathymetric missions with the ROAZ autonomous surface vehicle. In particular, robotic surface vehicles such as ROAZ provide an efficient tool in risk assessment for shallow water environments and water land interface zones as the near surf zone in marine coast. ROAZ is an ocean capable catamaran for distinct oceanographic missions, and with the goal to fill the gap were other hydrographic surveys vehicles/systems are not compiled to operate, like very shallow water rivers and marine coastline surf zones. Therefore, the use of robotic systems for risk assessment is validated through several missions performed either in river scenario (in a very shallow water conditions) and in marine coastlines.

Swordfish: an Autonomous Surface Vehicle for Network Centric Operations

The design and development of the swordfish autonomous surface vehicle (ASV) system is discussed. Swordfish is an ocean capable 4.5 m long catamaran designed for network centric operations (with ocean and air going vehicles and human operators). In the basic configuration, Swordfish is both a survey vehicle and a communications node with gateways for broadband, Wi-Fi and GSM transports and underwater acoustic modems. In another configuration, Swordfish mounts a docking station for the autonomous underwater vehicle Isurus from Porto University. Swordfish has an advanced control architecture for multi-vehicle operations with mixed initiative interactions (human operators are allowed to interact with the control loops).

Autonomous Surface Vehicle Docking Manoeuvre with Visual Information

This work presents a hybrid coordinated manoeuvre for docking an autonomous surface vehicle with an autonomous underwater vehicle. The control manoeuvre uses visual information to estimate the AUV relative position and attitude in relation to the ASV and steers the ASV in order to dock with the AUV. The AUV is assumed to be at surface with only a small fraction of its volume visible. The system implemented in the autonomous surface vehicle ROAZ, developed by LSA-ISEP to perform missions in river environment, test autonomous AUV docking capabilities and multiple AUV/ASV coordinated missions is presented. Information from a low cost embedded robotics vision system (LSAVision), along with inertial navigation sensors is fused in an extended Kalman filter and used to determine AUV relative position and orientation to the surface vehicle The real time vision processing system is described and results are presented in operational scenario.

微型遥控潜水器视频监控系统

介绍了一种微型遥控潜水器视频监控系统,包括硬件装置及基于软件技术的视频数据处理技术。硬件装置完成视频信号的采集、传输、显示。视频数据处理技术解决了视频信号的捕获、存储、画面质量调节等。该系统已经在微型遥控潜水器中应用,效果良好。

从有缆遥控水下机器人到自治水下机器人

文章给出了水下机器人的定义 ,依据定义进行了分类 ,简要回顾了几类重要水下机器人的进展 ,指出了无人无缆自治水下机器人 (AUVs)是当今水下机器人研究与开发的热点 ,介绍了最近 2 0年沈阳自动化研究所与国内外有关单位合作 ,在水下机器人领域从无人有缆遥控水下机器人 (ROVs)到AUVs的研究开发工作 ,它从一个侧面反映了我国在这一领域的进展情况。

Manobras de condução assistida para veículos submarinos subactuados

A intervenção humana no manuseamento de veículos submarinos operados remotamente (ROVs) é um requisito necessário para garantir o sucesso da missão e a integridade do equipamento. Contudo, a sua teleoperação não é fácil, pelo que a condução assistida destes veículos torna-se relevante. Esta dissertação propõe uma solução para este problema para ROVs de 3DOF (surge, heave e yaw). São propostas duas abordagens distintas – numa primeira propõe-se um sistema de controlo Image Based Visual Servoing (IBVS) tendo em vista a utilização exclusiva de uma câmara (sensor existente neste tipo de sistemas) por forma a melhorar significativamente a teleoperação de um pequeno ROV; na segunda, propõe-se um sistema de controlo cinemático para o plano horizontal do veículo e um algoritmo de uma manobra capaz de dotar o ROV de movimento lateral através de uma trajectória dente-de-serra. Demonstrou-se em cenários de operação real que o sistema proposto na primeira abordagem permite ao operador de um ROV com 3DOF executar tarefas de alguma complexidade (estabilização) apenas através de comandos de alto nível, melhorando assim drasticamente a teleoperação e qualidade de inspecção do veículo em questão. Foi também desenvolvido um simulador do ROV em MATLAB para validação e avaliação das manobras, onde o sistema proposto na segunda abordagem foi validado com sucesso.

A New ROV Design: Issues on Low Drag and Mechanical Symmetry

This paper reports the design of a new remotely operated underwater vehicle (ROV), which has been developed at the Underwater Systems and Technology Laboratory (USTL) - University of Porto. This design is contextualized on the KOS project (Kits for underwater operations). The main issues addressed here concern directional drag minimization, symmetry, optimized thruster positioning, stability and layout of ROV components. This design is aimed at optimizing ROV performance for a set of different operational scenarios. This is achieved through modular configurations which are optimized for each different scenario.

A remotely interrogated all-optical Rb-87 magnetometer

Atomic magnetometry was performed at Earth's magnetic field over a free-space distance of ten meters. Two laser beams aimed at a distant alkali-vapor cell excited and detected the Rb-87 magnetic resonance, allowing the magnetic field within the cell to be interrogated remotely. Operated as a driven oscillator, the magnetometer measured the geomagnetic field with less than or similar to 3.5 pT precision in a similar to 2 s data acquisition; this precision was likely limited by ambient field fluctuations. The sensor was also operated in self-oscillating mode with a 5.3 pT root Hz noise floor. Further optimization will yield a high-bandwidth, fully remote magnetometer with sub-pT sensitivity. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4747206]

Sea-floor videos and photographs (benthos) along 6 shelf profiles from the eastern Weddell Sea, Antarctica taken with remote operated vehicel CHEROKEE during Polarstern cruise ANT-XXI/2

The ROV operations had three objectives: (1) to check, whether the "Cherokee" system is suited for advanced benthological work in the high latitude Antarctic shelf areas; (2) to support the disturbance experiment, providing immediate visual Information; (3) to continue ecological work that started in 1989 at the hilltop situated at the northern margin of the Norsel Bank off the 4-Seasons Inlet (Weddell Sea). The "Cherokee" is was equipped with 3 video cameras, 2 of which support the operation. A high resolution Tritech Typhoon camera is used for scientific observations to be recorded. In addition, the ROV has a manipulator, a still camera, lights and strobe, compass, 2 lasers, a Posidonia transponder and an obstacle avoidance Sonar. The size of the vehicle is 160 X 90 X 90cm. In the present configuration without TMS (tether management system) the deployment has to start with paying out the full cable length, lay it in loops on deck and connect the glass fibres at the tether's spool winch. After a final technical check the vehicle is deployed into the water, actively driven perpendicular to the ship's axis and floatings are fixed to the tether. At a cable length of approx. 50 m, the tether is tightened to the depressor by several cable ties and both components are lowered towards the sea floor, the vehicle by the thruster's propulsion and the depressor by the ship's winch. At 5 m intervals the tether has to be tied to the single conductor cable. In good weather conditions the instruments supporting the navigation of the ROV, especially the Posidonia system, allow an operation mode to follow the ship's course if the ship's speed is slow. Together with the lasers which act as a scale in the images they also allow a reproducible scientific analysis since the transect can be plotted in a GIS system. Consequently, the area observed can be easily calculated. An operation as a predominantly drifting system, especially in areas with bottom near currents, is also possible, however, the connection of the tether at the rear of the vehicle is unsuitable for such conditions. The recovery of the system corresponds to that of the deployment. Most important is to reach the surface of the sea at a safe distance perpendicular to the ship's axis in order not to interfere with the ship's propellers. During this phase the Posidonia transponder system is of high relevance although it has to be switched off at a water depth of approx. 40 m. The minimum personal needed is 4 persons to handle the tether on deck, one person to operate the ship's winch, one pilot and one additional technician for the ROV's operation itself, one scientist, and one person on the ship's bridge in addition to one on deck for whale watching when the Posidonia system is in use. The time for the deployment of the ROV until it reaches the sea floor depends on the water depth and consequently on the length of the cable to be paid out beforehand and to be tightened to the single conductor cable. Deployment and recovery at intermediate water depths can last up to 2 hours each. A reasonable time for benthological observations close to the sea floor is 1 to 3 hours but can be extended if scientifically justified. Preliminary results: after a first test station, the ROV was deployed 3 times for observations related to the disturbance experiment. A first attempt to Cross the hilltop at the northern margin of the Norsel Bank close to the 4- Seasons Inlet was successful only for the first hundreds of metres transect length. The benthic community was dominated in biomass by the demosponge Cinachyra barbata. Due to the strong current of approx. 1 nm/h, the design of the system, and an expected more difficult current regime between grounded icebergs and the top of the hilltop the operation was stopped before the hilltop was reached. In a second attempt the hilltop was successfully crossed because the current and wind situation was much more suitable. In contrast to earlier expeditions with the "sprint" ROV it was the first time that both slopes, the smoother in the northeast and the steeper in the southwest were continuously observed during one cast. A coarse classification of the hilltop fauna shows patches dominated by single taxa: cnidarians, hydrozoans, holothurians, sea urchins and stalked sponges. Approximately 20 % of the north-eastern slope was devastated by grounding icebergs. Here the sediments consisted of large boulders, gravel or blocks of finer sediment looking like an irregularly ploughed field. On the Norsel Bank the Cinachyra concentrations were locally associated with high abundances of sea anemones. Total observation time amounted to 11.5 hours corresponding to almost 6-9 km transect length.

A new three phase method (SDP method) for the multi-objective vehicle routing problem with simultaneous delvery and pickup (VRPSDP)

Transportation service operators are witnessing a growing demand for bi-directional movement of goods. Given this, the following thesis considers an extension to the vehicle routing problem (VRP) known as the delivery and pickup transportation problem (DPP), where delivery and pickup demands may occupy the same route. The problem is formulated here as the vehicle routing problem with simultaneous delivery and pickup (VRPSDP), which requires the concurrent service of the demands at the customer location. This formulation provides the greatest opportunity for cost savings for both the service provider and recipient. The aims of this research are to propose a new theoretical design to solve the multi-objective VRPSDP, provide software support for the suggested design and validate the method through a set of experiments. A new real-life based multi-objective VRPSDP is studied here, which requires the minimisation of the often conflicting objectives: operated vehicle fleet size, total routing distance and the maximum variation between route distances (workload variation). The former two objectives are commonly encountered in the domain and the latter is introduced here because it is essential for real-life routing problems. The VRPSDP is defined as a hard combinatorial optimisation problem, therefore an approximation method, Simultaneous Delivery and Pickup method (SDPmethod) is proposed to solve it. The SDPmethod consists of three phases. The first phase constructs a set of diverse partial solutions, where one is expected to form part of the near-optimal solution. The second phase determines assignment possibilities for each sub-problem. The third phase solves the sub-problems using a parallel genetic algorithm. The suggested genetic algorithm is improved by the introduction of a set of tools: genetic operator switching mechanism via diversity thresholds, accuracy analysis tool and a new fitness evaluation mechanism. This three phase method is proposed to address the shortcoming that exists in the domain, where an initial solution is built only then to be completely dismantled and redesigned in the optimisation phase. In addition, a new routing heuristic, RouteAlg, is proposed to solve the VRPSDP sub-problem, the travelling salesman problem with simultaneous delivery and pickup (TSPSDP). The experimental studies are conducted using the well known benchmark Salhi and Nagy (1999) test problems, where the SDPmethod and RouteAlg solutions are compared with the prominent works in the VRPSDP domain. The SDPmethod has demonstrated to be an effective method for solving the multi-objective VRPSDP and the RouteAlg for the TSPSDP.

Characterization of Atlantic Cod Spawning Habitat and Behavior in Icelandic Coastal Waters

The physical habitat used during spawning may potentially be an important factor affecting reproductive output of broadcast spawning marine fishes, particularly for species with complex, substrate-oriented mating systems and behaviors, such as Atlantic cod Gadus morhua. We characterized the habitat use and behavior of spawning Atlantic cod at two locations off the coast of southwestern Iceland during a 2-d research cruise (15–16 April 2009). We simultaneously operated two different active hydroacoustic gear types, a split beam echosounder and a dual frequency imaging sonar (DIDSON), as well as a remotely operated underwater vehicle (ROV). A total of five fish species were identified through ROV surveys: including cusk Brosme brosme, Atlantic cod, haddock Melanogrammus aeglefinus, lemon sole Microstomus kitt, and Atlantic redfish Sebastes spp. Of the three habitats identified in the acoustic surveys, the transitional habitat between boulder/lava field and sand habitats was characterized by greater fish density and acoustic target strength compared to that of sand or boulder/lava field habitats independently. Atlantic cod were observed behaving in a manner consistent with published descriptions of spawning. Individuals were observed ascending 1–5 m into the water column from the bottom at an average vertical swimming speed of 0.20–0.25 m s−1 and maintained an average spacing of 1.0–1.4 m between individuals. Our results suggest that cod do not choose spawning locations indiscriminately despite the fact that it is a broadcast spawning fish with planktonic eggs that are released well above the seafloor.

Low-Cost vision-based AUV guidance system for reef navigation

Ensuring the long term viability of reef environments requires essential monitoring of many aspects of these ecosystems. However, the sheer size of these unstructured environments (for example Australia’s Great Barrier Reef pose a number of challenges for current monitoring platforms which are typically remote operated and required significant resources and infrastructure. Therefore, a primary objective of the CSIRO robotic reef monitoring project is to develop and deploy a large number of AUV teams to perform broadscale reef surveying. In order to achieve this, the platforms must be cheap, even possibly disposable. This paper presents the results of a preliminary investigation into the performance of a low-cost sensor suite and associated processing techniques for vision and inertial-based navigation within a highly unstructured reef environment.